Wind and solar technologies have experienced rapid market growth recently as a result of the growing interest for implementation of renewable energy. However, the intermittency of wind and solar power is a major obstacle to their broader use. The additional risks of unexpected interruptions and mismatch with demand have hindered the expansion of these two primary renewable resources. The goal of this research is to analyze an integrated energy system that includes a novel configuration of wind and solar coupled with two storage methods to make both wind and solar sources dispatchable during peak demand, thereby enabling their broader use. Named DSWiSS for Dispatchable Solar Wind Storage System, the proposed system utilizes compressed air energy storage (CAES) that is driven from wind energy and thermal storage supplied by concentrating solar thermal power in order to achieve this desired dispatchability. Although DSWiSS mimics the operation of a typical CAES facility, the replacement of energy derived from fossil fuels with energy generated from renewable resources makes this system unique. While current CAES facilities use off peak electricity to power their compressors, this system uses power from wind turbines. Also, rather than using natural gas for heating of the compressed air before its expansion through a turbine, DSWiSS uses solar thermal energy and thermal storage. For this research, two models were created; the first is a dynamic model of a 1.5 MW variable speed wind turbine, programmed in PSCAD/EMTDC, that utilizes rotor resistive control to maintain rated power output. This model simulates the dynamic response of the wind turbine to changing wind conditions as well as the nominal performance parameters at all wind speeds. The second model is a steady state thermodynamic simulation of the turbomachinery power unit in the DSWiSS facility. By assuming conditions similar to those of a currently operating CAES facility in McIntosh, Alabama, the model calculates the performance parameters of DSWiSS and estimates the relative energy input requirements. By combining these models with a levelized lifetime cost analysis estimates of the power system performance and the cost of energy for the DSWiSS facility were estimated. The combination of these components yielded an efficiency greater than 46% for the main power block and a nearly equal utilization of both renewable resources. It was also estimated that the overall system is only slightly more expensive per unit of electricity generated than the current technologies employed today, namely coal, nuclear, and natural gas, but is comparable to a stand-alone solar thermal facility. However, this economic analysis, though accurate with regard to the technologies chosen, will not be complete until cost values can be placed on some of the externalities associated with power generation such as fuel cost volatility, national security, and emissions. / text

Le concentrateur à réflecteur linéaire de Fresnel (LFR) est une technologie solaire thermodynamique en plein essor : petites applications industrielles (chaleur, froid, électricité) à centrales électriques (10-100 MWel). Ce travail de thèse établit un modèle global du procédé solaire, en régime permanent, pour un prédimensionnement du système. Le modèle comprend trois parties chaînées : (i) les transferts radiatifs dans le concentrateur optique, modélisés précisément par une méthode de Monte Carlo (environnement EDStar) ; (ii) les transferts thermiques dans le récepteur, évalués analytiquement (puissances, températures) ; (iii) le cycle thermodynamique, avec Thermoptim. L’application étudiée couple un concentrateur LFR à un moteur Ericsson. L’air est fluide caloporteur et de travail. Un prototype est en construction. L’hybridation et le stockage thermique sont des options clés. Un modèle systémique permettrait d’optimiser l’opération du procédé, en étudiant son comportement dynamique. / Linear Fresnel Reflector (LFR) is a promising Concentrating Solar Power technology. Research is booming and industrial applications are emerging. Applications range from small production units (heat, cold, electricity) to utility scale power plants (several tenths of MW). This PhD work establishes a global model of the solar process, in order to improve our knowledge of the system’s performances. It is a static model suited for a pre-design of the system. The model is chaining three parts. Radiative heat transfer in the optical concentrator is modelled by Monte Carlo statistical Method. The algorithm enables a detailed study of any geometrical configuration, especially through absorbed power flux maps on the receiver. The simulation tool is using the environment of development EDStar. The thermal model calculates analytically the useful thermal power, losses and temperature profiles along the receiver (glass cover, fluid, pipe...). The thermodynamic cycle is simulated analytically using the software Thermoptim. The studied application uses air as heat transfer and working fluid. Air directly feeds an Ericsson engine. The engine developed by LaTEP laboratory is promising for small scale cogeneration (1 to several tenths of kWel). The prototype Linear Fresnel Reflector built in Ecole des Mines d’Albi will enable experimental study of a solar process coupling an LFR concentrator and an Ericsson engine. The technology under study can feed a power plant or a cogeneration system in the industry, producing electricity and heat at 100 to 250°C. Hybridisation with an other energy source (biomass, gas...) and thermal storage (molten salt?) are key features to investigate. To optimise the operating strategy of the process, dynamic behaviour must be studied: a systemic or agent based model is a very relevant approach.

Segundo o Atlas Brasileiro de Energia Solar, apesar das diferentes características climáticas observadas no Brasil, pode-se constatar que a média anual de irradiação solar global apresenta boa uniformidade e elevados índices por todo o país. Os valores desta grandeza em quase toda a extensão do território brasileiro (4200-6700 Wh/m2/dia) são superiores aos da maioria dos países da União Europeia, como Alemanha (900-1250 Wh/m2/dia), França (900-1650 Wh/m2/dia) e Espanha (1200-1850 Wh/m2/dia), onde projetos para aproveitamento de energia solar, alguns contando com fortes incentivos governamentais, são amplamente disseminados. Grande parte dos avanços científicos obtidos nos estudos sobre aproveitamento da energia solar se deve à utilização de simuladores solares compactos nos experimentos de longa duração. Ao substituir o Sol por fontes artificiais, como lâmpadas capazes de emitir radiação próxima à solar, os simuladores eliminam a dependência de fatores naturais como condições climáticas, horário do dia, intermitência e movimento de direção da radiação solar. O projeto proposto para esta dissertação de Mestrado teve como objetivo o domínio do processo de concepção e fabricação de um simulador solar concentrador formado por lâmpadas e um refletor ótico. Uma vez dominada a técnica, um modelo piloto de simulador solar foi construído e alguns testes executados para avaliar a qualidade do projeto, a resistência dos componentes e o fator de concentração do aparato. / According to the Brazilian Atlas of Solar Energy, despite the different climatic characteristics observed in Brazil, the annual average of global solar irradiation has good uniformity and high levels throughout the country. The values of global solar irradiation in almost the entire length of Brazil (4200-6700 Wh/m2/day) are higher than those observed in most European Union countries, like Germany (900-1250 Wh/m2/day), France (900-1650 Wh/m2/day) and Spain (1200-1850 Wh/m2/day), where projects for solar energy applications, some of them relying on strong government incentives, are widely disseminated. Several scientific and technological advances made in the study of solar energy applications are due to the use of compact solar simulators in long-term experiments. Replacing the Sun by artificial sources, such as arc lamps with radiation emission similar to the Sun spectrum, indoor simulators avoid the dependence on natural conditions such as the weather, the daytime, the sunlight intermittence and the directional change of the solar radiation. The project proposed for this dissertation aimed to master the design and manufacturing processes of a high-flux solar simulator consisting of arc lamps and an optical reflector. Once technique was understood, a solar simulation pilot model was built and some tests were performed to assess the project quality, the resistance of components and the apparatus concentration factor.

Submitted by Silvana Teresinha Dornelles Studzinski (sstudzinski) on 2015-11-30T14:46:17Z No. of bitstreams: 1 Sérgio Luiz Bohrer Filho_.pdf: 1393460 bytes, checksum: 335661e44d51f93aa77abb3a780e6e5a (MD5) / Made available in DSpace on 2015-11-30T14:46:17Z (GMT). No. of bitstreams: 1 Sérgio Luiz Bohrer Filho_.pdf: 1393460 bytes, checksum: 335661e44d51f93aa77abb3a780e6e5a (MD5) Previous issue date: 2015-10-14 / CAPES - Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / PROSUP - Programa de Suporte à Pós-Gradução de Instituições de Ensino Particulares / Este trabalho apresenta um estudo de viabilidade de inserção de energia solar térmica na matriz elétrica brasileira, através de integração de um campo de energia termosolar concentrada com uma usina termelétrica de ciclo combinado localizada na Região Centro-Oeste. A atual conjuntura do setor elétrico, que apresenta crescimento do despacho termelétrico e consequente elevação dos custos de geração de energia elétrica, provocados principalmente por períodos de Energia Natural Afluente (ENA) abaixo da média, justifica o desenvolvimento de fontes alternativas. O objetivo principal deste estudo é apresentar um modelo de empreendimento de produção de eletricidade por meio de fonte solar térmica, compatível à realidade tecnológica e econômica do mercado de energia. O estudo baseia-se na simulação de integração de um campo solar com tecnologia de concentração Fresnel linear e geração direta de vapor superaquecido, junto à Usina Termelétrica Luís Carlos Prestes (UTE-LCP), no município de Três Lagoas, no estado de Mato Grosso do Sul. O desempenho do campo solar é verificado através do software System Advisor Model (SAM) da National Renewable Energy Laboratory (NREL) e a produção adicional de termeletricidade é determinada com base na análise de eficiência do ciclo de Rankine da UTE-LCP. Por fim, é realizada a análise financeira do projeto através de ferramentas de engenharia econômica, onde identifica-se um custo nivelado da energia elétrica (LCOE) de pelo menos 139,24 USD MW-1h-1, uma redução de 42,7% em relação às estimativas de custo internacionais para usinas heliotérmicas. Análises de sensibilidade indicam que o custo do capital tem impacto crítico sobre o LCOE, fato atribuído ao caráter de alta dependência dos recursos de capital da tecnologia solar térmica. / This work presents a study of concentrated solar power insertion in the Brazilian energy matrix, through integration of the solar energy with Luís Carlos Prestes Thermoelectric Power Plant (UTE-LCP) in Três Lagoas city. The current situation of the Brazilian electricity sector, which has presented strong growth of thermoelectric dispatch in recent years and the consequent increase in the cost of electricity generation, justifies the development of alternative energy sources. The purpose of this study is to present a model of electricity generation through thermal solar source compatible to technological and economic realities of the energy market. The study is based on evaluation of the linear Fresnel reflector with direct steam generation, because this configuration has investment, operation and maintenance attractive costs. The performance of the solar field is simulated in the System Advisor Model software (SAM) of the National Renewable Energy Laboratory (NREL). The predict performance is used with UTE-LCP operational database to estimate the additional electricity generation. Finally, the financial analysis is carried out through economic engineering tools, which identifies a Levelized Cost of Electricity (LCOE) of the 139.24 USD MW-1h-1 at least. This LCOE is 42.7% less than cost estimates for Concentrating Solar Power plants. Sensitivity analysis indicates that the cost of capital has critical impact on the LCOE, which was attributed to the character of high dependence on Concentrating Solar Power (CSP) capital resources.

La durabilité des miroirs solaires est un point clé pour le développement des centrales solaires à concentration, du fait de l’investissement important, des 30 ans d’opération visés et des zones d’implantations aux climats agressifs. Ces travaux de recherche portent ainsi sur l’étude des modes de dégradation et de la durabilité de miroirs solaires en verre monolithiques ou laminés. Cette thèse a permis d’appliquer avec succès au CSP une méthodologie de prédiction de la durée de vie développée dans des domaines plus matures. Les corrélations entre les vieillissements accélérés et les expositions extérieures réalisées sur trois sites ont mis en avant le rôle prédominant de l’eau et de l’irradiance dans la dégradation des peintures de protection des miroirs monolithiques. Les essais en chaleur humide ont quant à eux été jugés trop agressifs pour les miroirs, considérant de plus les conditions climatiques des sites d’application potentiels. Les résultats expérimentaux des essais de vieillissements accélérés ont conduit à la détermination des paramètres cinétiques des miroirs inclus dans les relations mathématiques modélisant les principaux facteurs de stress identifiés précédemment. Les facteurs d’accélération ont ainsi été calculés pour des essais standards par rapport à des sites comportant des centrales CSP opérationnelles. Ce travail a permis au final d’estimer des durées de vie des miroirs sur les sites choisis, en considérant que seuls les facteurs de stress étudiés intervenaient dans la dégradation. / Durability of solar mirrors is a key point for the development of concentrating solar power plants, because of the large investment, the goal of 30 years lifetime and of the implantations areas with hostile climates. This research work concerns the study of degradation modes and of monolithic or laminated glass solar mirrors durability. This thesis allows to successfully apply to CSP a lifetime prediction method already developed in more mature fields. Correlations between accelerated ageing tests and natural outdoor exposures performed on three sites evidence the predominant role of water and irradiance in protection paints of monolithic mirrors degradation. Damp heat tests were evaluated too aggressive for mirrors, considering thus the climatic conditions of potential application sites. Experimental results of accelerated ageing tests lead to the determination of kinetic parameters included in mathematical relationships modelling the main stress factors previously identified. Acceleration factors were then calculated for standard tests compared to sites with operational CSP plants. This work finally allows to estimate lifetimes of mirrors on specific sites, assuming that only the studied stress factors take part in degradation.

The percentage of renewable energy within the global electric power generation portfolio is expected to increase rapidly over the next few decades due to increasing concerns about climate change, fossil fuel costs, and energy security. Solar thermal energy, also known as concentrating solar power (CSP), is emerging as an important solution to new demands for clean, renewable electricity generation. Dish-Stirling (DS) technology, a form of CSP, is a relatively new player in the renewable energy market, although research in the technology has been ongoing now for nearly thirty years. The first large plant utilizing DS technology, rated at 1.5 MW, came online in January 2010 in Peoria, AZ, and plants rated for several hundred MW are in the planning stages. Increasing capacity of this technology within the utility grid requires extensive dynamic simulation studies to ensure that the power system maintains its safety and reliability in spite of the technological challenges that DS technology presents, particularly related to the intermittency of the energy source and its use of a non-conventional asynchronous generator. The research presented in this thesis attempts to fill in the gaps between the well established research on Stirling engines in the world of thermodynamics and the use of DS systems in electric power system applications, a topic which has received scant attention in publications since the emergence of this technology. DS technology uses a paraboloidal shaped dish of mirrors to concentrate sunlight to a single point. The high temperatures achieved at the focal point of the mirrors is used as a heat source for the Stirling engine, which is a closed-cycle, external heat engine. Invented by the Scottish clergyman Robert Stirling in 1816, the Stirling engine is capable of high efficiency and releases no emissions, making it highly compatible with concentrated solar energy. The Stirling engine turns a squirrel-cage induction generator, where electricity is delivered through underground cables from thousands of independent, autonomous 10-25 kW rated DS units in a large solar farm. A dynamic model of the DS system is presented in this thesis, including models of the Stirling engine working gas and mechanical dynamics. Custom FORTRAN code is written to model the Stirling engine dynamics within PSCAD/EMTDC. The Stirling engine and various other components of the DS system are incorporated into an electrical network, including first a single-machine, infinite bus network, and then a larger 12-bus network including conventional generators, loads, and transmission lines. An analysis of the DS control systems is presented, and simulation results are provided to demonstrate the system's steady state and dynamic behavior within these electric power networks. Potential grid interconnection requirements are discussed, including issues with power factor correction and low voltage ride-through, and simulation results are provided to illustrate the dish-Stirling system's capability for meeting such requirements.

The demand for clean and environmentally benign energy resources has been a great concern in the last two decades. To alleviate the associated environmental problems, reduction of the use of fossil fuels by developing more cost-effective renewable energy technologies becomes more and more significant. Among various types of renewable energy sources, solar energy and bioenergy take a great proportion. This dissertation focuses on the heat transfer and flow in solar energy and bioenergy systems, specifically for Thermal Energy Storage (TES) systems in Concentrated Solar Power (CSP) plants and open-channel algal culture raceways for biofuel production. The first part of this dissertation is the discussion about mathematical modeling, numerical simulation and experimental investigation of solar TES system. First of all, in order to accurately and efficiently simulate the conjugate heat transfer between Heat Transfer Fluid (HTF) and filler material in four different solid-fluid TES configurations, formulas of an effective heat transfer coefficient were theoretically developed and presented by extending the validity of Lumped Capacitance Method (LCM) to large Biot number, as well as verifications/validations to this simplified model. Secondly, to provide design guidelines for TES system in CSP plant using Phase Change Materials (PCM), a general storage tank volume sizing strategy and an energy storage startup strategy were proposed using the enthalpy-based 1D transient model. Then experimental investigations were conducted to explore a novel thermal storage material. The thermal storage performances were also compared between this novel storage material and concrete at a temperature range from 400 °C to 500 °C. It is recommended to apply this novel thermal storage material to replace concrete at high operating temperatures in sensible heat TES systems. The second part of this dissertation mainly focuses on the numerical and experimental study of an open-channel algae culture raceway for biofuel production. According to the proposed flow field design of ARID-HV algal raceway, experiments and numerical simulation have been conducted to understand the enhancement of flow mixing in the flow field of ARID-HV raceway by cutting slots on top of the dam near the dead zones. A new method was proposed to quantitatively evaluate the flow mixing by using the statistics of temporal and spatial distribution of the massless fluid particles (centered in each cell at the inlet surface) in the raceway collecting the data of path-lines of fluid particles from CFD results. It is hoped that this method can be applied to assist the algal raceway flow field design as well as other engineering applications. The third part introduces the details about the construction work of a high temperature molten salt test loop. Because of the limited operating temperature of conventional synthetic oils, in order to obtain higher energy conversion efficiency, higher operating temperature is always desirable in a CSP plant which leads to the requirement of new generation of HTF. Currently, a halide salt eutectic mixture (NaCl-KCl-ZnCl₂) as a potential HTF for future CSP applications has been proposed by a multi-institute research team, led by University of Arizona. The thermophysical properties of the halide eutectic salt have been measured. However, this new developed halide eutectic salt has not been tested in a circulating loop at a high operating temperature for the measurement of heat transfer coefficient. It is a significant effort to build such a test system due to extremely high operating temperature. As a consequence, in the third part of this dissertation, details about the design of the lab-scale test system and all the equipment items will be introduced. The investigations included in this dissertation for the heat transfer and flow in solar energy and bioenergy systems are of particular interest to the renewable energy engineering community. It is expected that the proposed methods can provide useful information for engineers and researchers.

Segundo o Atlas Brasileiro de Energia Solar, apesar das diferentes características climáticas observadas no Brasil, pode-se constatar que a média anual de irradiação solar global apresenta boa uniformidade e elevados índices por todo o país. Os valores desta grandeza em quase toda a extensão do território brasileiro (4200-6700 Wh/m2/dia) são superiores aos da maioria dos países da União Europeia, como Alemanha (900-1250 Wh/m2/dia), França (900-1650 Wh/m2/dia) e Espanha (1200-1850 Wh/m2/dia), onde projetos para aproveitamento de energia solar, alguns contando com fortes incentivos governamentais, são amplamente disseminados. Grande parte dos avanços científicos obtidos nos estudos sobre aproveitamento da energia solar se deve à utilização de simuladores solares compactos nos experimentos de longa duração. Ao substituir o Sol por fontes artificiais, como lâmpadas capazes de emitir radiação próxima à solar, os simuladores eliminam a dependência de fatores naturais como condições climáticas, horário do dia, intermitência e movimento de direção da radiação solar. O projeto proposto para esta dissertação de Mestrado teve como objetivo o domínio do processo de concepção e fabricação de um simulador solar concentrador formado por lâmpadas e um refletor ótico. Uma vez dominada a técnica, um modelo piloto de simulador solar foi construído e alguns testes executados para avaliar a qualidade do projeto, a resistência dos componentes e o fator de concentração do aparato. / According to the Brazilian Atlas of Solar Energy, despite the different climatic characteristics observed in Brazil, the annual average of global solar irradiation has good uniformity and high levels throughout the country. The values of global solar irradiation in almost the entire length of Brazil (4200-6700 Wh/m2/day) are higher than those observed in most European Union countries, like Germany (900-1250 Wh/m2/day), France (900-1650 Wh/m2/day) and Spain (1200-1850 Wh/m2/day), where projects for solar energy applications, some of them relying on strong government incentives, are widely disseminated. Several scientific and technological advances made in the study of solar energy applications are due to the use of compact solar simulators in long-term experiments. Replacing the Sun by artificial sources, such as arc lamps with radiation emission similar to the Sun spectrum, indoor simulators avoid the dependence on natural conditions such as the weather, the daytime, the sunlight intermittence and the directional change of the solar radiation. The project proposed for this dissertation aimed to master the design and manufacturing processes of a high-flux solar simulator consisting of arc lamps and an optical reflector. Once technique was understood, a solar simulation pilot model was built and some tests were performed to assess the project quality, the resistance of components and the apparatus concentration factor.

Cette thèse, financée dans le cadre du projet européen CSP2, porte sur l'étude d'un nouveau type de récepteur solaire thermique à concentration utilisant comme fluide caloporteur une suspension dense de fines particules en circulation ascendante dans des tubes verticaux. Ladite suspension est obtenue par fluidisation de particules de classe A. Le principe consiste à créer un écoulement ascendant de la suspension dans un tube vertical exposé au rayonnement solaire concentré qui chauffe la paroi du tube, qui transmet ensuite cette chaleur aux particules, qui la transportent jusqu'à un cycle de conversion d'énergie pour la production d'électricité. Au contraire des fluides solaires classiques, les particules peuvent atteindre les hautes températures (> 700 °C) permettant l'utilisation de cycles à haut rendement de conversion (Brayton, cycles combinés), tout en permettant un stockage direct de la pour une production continue. Au cours de la thèse, un récepteur à un tube a été testé avec succès au grand four solaire du laboratoire PROMES-CNRS à Odeillo, les particules en sortie atteignant 750 °C, ce qui a prouvé la faisabilité du concept et permis la détermination des premières valeurs de coefficient d'échange de chaleur tube-suspension. L'hydrodynamique de l'écoulement et les mécanismes d'échange de chaleur ont été observés grâce à des simulations numériques 3D. Un récepteur de 150 kWth à 16 tubes a ensuite été testé et modélisé, validant l'utilisation du procédé à plus grande échelle. / This thesis, financed in the frame of the CSP2 European project, concerns the study of a new kind of thermal concentrating solar receiver using a dense suspension of solid particles circulating upward in vertical tubes. The suspension is obtained by fluidizing Geldart A-type particles. The principle consists in creating an upward flow of the suspension in a vertical tube exposed to the concentrated solar radiation that heats the tube wall. The heat is then transmitted to the particles circulating inside that transport it to a conversion cycle for electricity production. Contrarily to usual solar heat transfer fluids, particles can reach high temperatures (> 700 °C) that permit to power high efficiency thermodynamic cycles such as Brayton or combined cycles. Moreover they can be used as a direct heat storage medium for continuous electricity production. During this thesis, a one-tube solar receiver was successfully tested at the PROMES-CNRS solar furnace in Odeillo, with particle outlet temperatures of 750 °C reached. The first values of wall-to-suspension heat transfer coefficient were calculated and a Nusselt correlation was determined. A specific flow pattern with a particle downward flux close to the wall and upward flux in the tube center was underlined. The flow hydrodynamics and the heat transfer mechanisms were studied thanks to 3D numerical simulations. A 16-tube 150 kWth receiver was finally tested and modeled, proving the process applicability at larger scale.

The change in climate as a consequence of anthropogenic activities is a subject ofmajor concerns. In order to reduce the amount of greenhouse gas emissions inthe atmosphere, the utilization of renewable, fossil-free power generationapplications becomes inevitable. Geothermal and solar energy play a major rolein covering the increased demand for renewable energy sources of today’s andfuture’s society. A special focus hereby lies on the Concentrating Solar Powertechnologies and different geothermal concepts. The costs for producingelectricity through Concentrating Solar Power and therefore Parabolic Trough Collectorsas well as geothermal conversion technologies are still comparatively high. Inorder to minimize these expenses and maximize the cycle’s efficiency, thepossible synergies of a hybridization of these two technologies becomeapparent. This thesis therefore investigates the thermodynamic and economicbenefits and drawbacks of this combination from a global perspective. For that,a Parabolic Trough Collector system is combined with the geothermal conversionconcepts of Direct Steam, Single and Double Flash, Organic Rankine as well asKalina Cycles. The solar integrations under investigation are Superheat,Preheat and Superheat & Reheat of the geothermal fluid. The thermodynamicanalysis focuses on the thermal and utilization efficiencies, as well as therequired Parabolic Trough Collector area. The results indicate that in the caseof the Superheat and Superheat & Reheat setup, the thermal efficiency canbe improved for all geothermal concepts in comparison to their correspondinggeothermal stand-alone case. The Preheat cases, with the major contributionfrom solar energy, are not able to improve the cycle’s thermal efficiencyrelative to the reference setup. From an exergy perspective the findings varysignificantly depending on the applied boundary conditions. Still, almost allcases were able to improve the cycle’s performance compared to the referencecase. For the economic evaluation, the capital investment costs and thelevelized costs of electricity are studied. The capital costs increasesignificantly when adding solar energy to the geothermal cycle. The levelizedelectricity costs could not be lowered for any hybridization case compared tothe reference only-geothermal configurations. The prices vary between20.04 €/MWh and 373.42 €/MWh. When conducting a sensitivity analysison the solar system price and the annual mean irradiance, the Kalina Superheatand Superheat & Reheat, as well as the Organic Rankine Preheathybridizations become cost competitive relative to the reference cases.Concluding, it is important to remark, that even if the hybridization of the ParabolicTrough and the different geothermal concepts makes sense from a thermodynamicperspective, the decisive levelized costs of electricity could not be improved.It is, however, possible that these costs can be further reduced under speciallocal conditions, making the addition of Parabolic Trough solar heat tospecific geothermal concepts favorable.