Materiais poliméricos têm sido explorados para o encapsulamento e liberação controlada de moléculas e o CO2-sc é um dos solventes alternativos de maior interesse da indústria farmacêutica para tal, por não deixar resíduos no produto final. Neste trabalho foram sintetizados e caracterizados polímeros do tipo \"core-shell\" tendo como \"core\" poligliceróis hiperramificados, sintetizados via abertura de anel glicidol, iniciados por três diferentes polióis e possuindo dois tipos de \"shell\" contendo grupos acetila, potencialmente compatíveis com CO2-sc. Também foi sintetizada β-Ciclodextrina peracetilada (TA-β-CD) que foi utilizada como molécula encapsulante modelo, por também ser um tipo de poliéter, ser reconhecida pela sua capacidade encapsulante, por ser uma ciclodextrina, e ser solúvel no CO2-sc. O Ibuprofeno foi o fármaco utilizado como modelo de molécula encapsulada, por ser solúvel em CO2-sc e possuir logP intermediário. O primeiro grupo de polímeros foram os poligliceróis peracetilados (PGH-Acs), que possuiam grupos acetilas como \"shell\". O estudo de seu comportamento em CO2-denso (CO2-sc e CO2 líquido próximo ao ponto crítico), pré-requisito para o encapsulamento neste meio, foi avaliado através de experimentos de expansão volumétrica e/ou solubilidade e determinação de pontos de névoa. Estes materiais apresentaram solubilidade total ou parcial, solubilizaram o CO2 e apresentaram expansão volumétrica em sua presença. A incorporação de Ibuprofeno foi realizada com sucesso, alcançando teores pouco maiores do que o apresentado para a TA-β-CD, e se mostrou associada aos valores de temperatura de transição vítrea (Tg) dos polímeros, sendo que a caracterização dos materiais encapsulados sugere que a molécula do fármaco interage preferencialmente com os grupos acetila dos materiais. Os dados do estudo de liberação das moléculas de Ibuprofeno dos materiais encapsulantes foi modelado principalmente segundo o modelo de Weibull e mostrou que ela foi prolongada, para os PGH-Acs, numa escala de horas e que foi menos lenta quanto mais hidrofílico o polímero, enquanto a liberação apresentada pela TA-&#946-CD foi imediata. Com o propósito de alcançar maiores teores de encapsulamento e liberações mais prolongadas, o segundo grupo de polímeros, com maior massa molar foi proposto. Este grupo foram os polímeros estrela PGH-PVAcs, contendo os mesmos cores dos polímeros anteriores, porém possuindo como \"shell\" cadeias lineares de poliacetato de vinila, sintetizadas via polimerização por Transferência Reversível de Cadeia por Adição-Fragmentação (RAFT). Os PGH-PVAcs solubilizaram o CO2 e apresentaram expansão, mas não foram solúveis neste solvente. A comparação do comportamento de todos os materiais estudados mostrou que a presença de grupos acetila é determinante para a sua CO2-filicidade, devido a interações específicas do tipo ácido-base de Lewis. Para os PGH-PVAcs, também houve encapsulamento do Ibuprofeno, os seus teores atingiram valores seis vezes maior do que os obtidos pelos PGH-Acs e também apresentaram associação com os valores de Tg dos polímeros. A liberação a partir deste materiais também foi prolongada, mas agora numa escala de dias e/ou meses. Os materiais obtidos se mostraram CO2-fílicos e capazes de encapsular Ibuprofeno em CO2-sc, sendo que o seu comportamento em CO2 denso, sua capacidade encapsulante e suas características de liberação podem ser modulados pela composição de sua estrutura \"core-shell\". / Polymeric materials have been explored for encapsulation and controlled release of molecules and sc-CO2 is one of the alternative solvents with most interest for the pharmaceutical industry for this purpose, for it does not leave traces at the final product. In this work, core-shell type polymers were synthesized and characterized. The polymers had hyperbranched polyglycerols initiated by three different polyols and synthesized through ring opening polymerization of glicidol, as cores; and had two diferente types of shells, bearing acetyl groups, potentially compatible with sc-CO2. Also Peracetilated β-Cyclodextrin (TA-β-CD) was synthesized, to be used as the model encapsulating material, because it is also a kind of polyether, is known for its encapsulating capacity, for being a cyclodextrin, and is soluble in sc-CO2. The Ibuprofen was the model drug chosen for the encapsualtion because it is soluble in sc-CO2 and has an intermediary logP. The first group of polymers were the peracetilated polyglycerols (PGH-Acs), bearing acethyl groups as their \"shell\". The behavior of those materials in dense CO2 (sc-CO2 and liquid CO2), pre-requisite for the encapsulation using this media, was evaluated through experiments of volumetric expansion and/or solubility and determination of cloud points. These materials presented solubility (total or partial), solubilized the CO2 and presented expansion in its presence. The incorporation of Ibuprofen was successfully performed, reaching levels slightly higher than the one presented by the TA-β-CD, and it showed to be associated with the values of the glass transition temperature (Tg) of the polymers; the characterization of the encapsulated materials suggests that the molecule of the drug interacts preferentially with the acetyl groups of the materials. The data of the release study of the Ibuprofen molecules from the encapsulating materials was modelled mainly through the Weibull model and showed, for the PGH-Acs materials, that the release was prolonged for a time scale of hours and was faster as the hydrophilicity of the polymers increases, while the release of Ibuprofeno from the TA-β-CD was immediate. Aiming to reach higher levels of encapsulation and also more prolonged releases, a second group of core-shell polymers, with a higher molar mass was proposed. This group was the one of the star polymers PGH-PVAc, having the same cores as the other polymers, but bearing as shell, linear chains of polyvinyl acetate, synthesized via Reversible Addition-Fragmentation Transfer (RAFT) Polymerization. The PGH-PVAc presented expansion, solubilized the solvent, but where not soluble in it. The comparison of the behavior of all studied materials showed that the presence of the acetyl groups is determinant for their CO2 -philicity and this because these groups and CO2 show specific interactions of the Lewis acid-base type. For the PGH-PVAcs the incorporation of Ibuprofen was also successfully performed and their levels reached six times higher than the ones obtained for the PGH-Acs and also presented association with the values of the Tg of the polymers. The release from these materials are also prolonged, but now in a time scale of days/months. The obtained materials have shown to be CO2-philic and able to encapsulate Ibuprofen in CO2-sc media. Their behavior in dense CO2, their encapsulation ability and the characteristics of the release can be modulated through the composition of their core-shell structure.

Submitted by Maria Beatriz Vieira (mbeatriz.vieira@gmail.com) on 2017-04-04T13:22:16Z No. of bitstreams: 2 license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) dissertacao_cintia_muller_leal.pdf: 2650724 bytes, checksum: 0735a2bb9f056999c0b6a14b82b893b4 (MD5) / Approved for entry into archive by Aline Batista (alinehb.ufpel@gmail.com) on 2017-04-07T18:52:23Z (GMT) No. of bitstreams: 2 dissertacao_cintia_muller_leal.pdf: 2650724 bytes, checksum: 0735a2bb9f056999c0b6a14b82b893b4 (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) / Approved for entry into archive by Aline Batista (alinehb.ufpel@gmail.com) on 2017-04-07T18:59:09Z (GMT) No. of bitstreams: 2 dissertacao_cintia_muller_leal.pdf: 2650724 bytes, checksum: 0735a2bb9f056999c0b6a14b82b893b4 (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) / Made available in DSpace on 2017-04-07T18:59:23Z (GMT). No. of bitstreams: 2 dissertacao_cintia_muller_leal.pdf: 2650724 bytes, checksum: 0735a2bb9f056999c0b6a14b82b893b4 (MD5) license_rdf: 0 bytes, checksum: d41d8cd98f00b204e9800998ecf8427e (MD5) Previous issue date: 2015-12-07 / Sem bolsa / Anacauíta (Schinus molle L.) é uma espécie arbórea de ocorrência nativa no Rio Grande do Sul, pioneira de pequeno porte, com importância ecológica, bioquímica e farmacológica, contudo suas sementes apresentam dormência, fato que dificulta a produção de mudas em escala comercial. Este trabalho objetivou avaliar métodos de superação de dormência das sementes de S. molle de um lote com 15 meses de armazenamento em câmara fria seca e germinação inicial de 5% quando submetidas a tratamento para superação de dormência com ácido sulfúrico por 160 minutos, utilizando diferentes tempos de escarificação mecânica (150, 300, 450 e 600 segundos) em escarificador elétrico equipado com lixa grão 80. O tratamento de 150 segundos de escarificação mecânica proporcionou maior percentual de germinação (61%), menor número de sementes mortas e plântulas anormais, maior massa seca e comprimento de plântulas aos sete dias, maior embebição e maior índice de velocidade de emergência (2,28). Para a produção de mudas desta espécie foram testados dois volumes de tubetes (100 e 175 mL) e quatro níveis de adubação com fertilizante de liberação controlada (FLC) Osmocote Plus, em um experimento fatorial 2 x 4. Os níveis de adubação com FLC foram zero, quatro, oito e doze gramas por litro de substrato. Os resultados quanto aos parâmetros de crescimento e qualidade de mudas, onde foram avaliados altura, diâmetro do coleto, número de folhas, relação altura/diâmetro do coleto, massa seca da raiz, massa seca da parte aérea, massa seca total, relação massa seca da parte aérea e massa seca da raiz, volume de raiz, índice de qualidade de Dickson, índice de clorofila, teor de clorofila a, clorofila b e carotenoides ao longo de 120 dias após a emergência das plântulas, revelou que o tubete de 175 mL e a dosagem de oito gramas de FLC por litro de substrato foi superior aos demais tratamentos por produzir mudas de anacauíta de alta qualidade. / Anacauita (Schinus molle L.) is arborea, native species in a Rio Grande do Sul small pioneer with ecological, biochemical and pharmacological importance, but its seeds present dormancy , a fact that hinders the production of seedlings on a commercial scale. This study aimed at evaluating methods of overcoming seed dormancy of S. molle of a batch of 15 months of storage in dry cold chamber and 5% germination when undergoing treatment to overcome dormancy with sulfuric acid for 160 minutes, using different times mechanical scarification (150, 300, 450 and 600 seconds) in electric scarifier equipped with 80 grit sandpaper. Treatment of 150 seconds of mechanical scarification showed higher germination percentage (61%), fewer dead seeds and abnormal seedlings, imbibition largest and most emergency velocity index (2.28). For the production of seedlings of this species were tested two volumes of tubes (100 and 175 mL) and four levels of fertilizer controlled release fertilizer (CRF) Osmocote Plus in 2 x 4 factorial experiment. Nutrient levels were CRF zero, four, eight and twelve grams per liter of substrate. The results regarding the growth parameters and quality seedlings, which were assessed height, stem diameter, number of leaves, height / stem diameter, root dry mass, dry mass of shoots, total dry matter, dry weight ratio of shoot and root dry mass, root volume, Dickson quality index, chlorophyll index, chlorophyll content a, chlorophyll b and carotenoids over 120 days after seedling emergence, revealed that the plastic tube 175 ml and the dose of CRF eight grams per liter substrate was superior to the other treatments for producing seedlings of high quality anacauita.

O crescimento da população mundial tem como consequência direta a busca cada vez maior de uma agricultura altamente produtiva e sustentável. Isto requer uso de nutrientes de modo que haja proporcionalidade entre a aplicação e a demanda de fertilizantes. Assim, surge uma crescente busca por materiais de revestimento, para que, ao serem aplicados sobre a superfície de sólidos, controlem a liberação de espécies fertilizantes ou mesmo, de um princípio ativo para o controle de pragas e doenças. Com isso, reduzem-se as quantidades aplicadas no solo e nas plantas, com grande impacto na redução de custos e de efeitos indesejáveis de deriva e excessos na aplicação, tornando a prática agrícola mais sustentável econômica e ambientalmente. Uma das mais importantes aplicações de materiais revestidos na agricultura consiste no revestimento ou encapsulamento da ureia. Este insumo mineral é útil devido ao seu elevado conteúdo de nitrogênio (entre 44 a 46% em massa). Porém, tem-se uma desvantagem devido às perdas por volatilização e por lixiviação, levando a um total que chega a 50%. Assim, este trabalho tem como finalidade desenvolver e avaliar novos sistemas de revestimentos poliméricos, a partir de poliuretanas (PU), para liberação controlada de ureia, além de propor uma nova abordagem de análise instrumental para ensaios acelerados de dissolução controlada de espécies revestidas. O trabalho foi dividido em três etapas: (i) preparação e caracterização dos materiais para revestimento, tendo por base polióis derivados do óleo de mamona e óleo de soja; (ii) desenvolvimento de uma célula de medida com controle de parâmetros físicos e geométricos, bem como um sistema de controle térmico e de agitação; (iii) execução dos ensaios de liberação em água para verificar a influencia da porcentagem de PU na taxa de liberação, assim como a cinética difusional e o tempo de retenção. A partir da caracterização dos revestimentos nota-se que os materiais à base de mamona apresentam melhor adesão à ureia, permitindo obter melhores resultados na retenção do macronutriente. Os ensaios de liberação mostraram que o aumento da porcentagem de polímero, retarda a taxa de liberação da ureia, visto que ensaios utilizando 5% estendem a liberação por até 40 dias. Também, observa-se que existe uma faixa ótima de recobrimento, sendo que valores superiores a 7% (PU mamona), não interferem significativamente na liberação, o que se confirma a partir da modulação de Peppas, mostrando valores baixos para a cinética de liberação desses materiais. Por fim, a célula de medida elaborada para adequar e padronizar procedimentos envolvendo liberação controlada permitiu o máximo de controle de parâmetros físicos e geométricos nos ensaios, mostrando-se uma excelente ferramenta para ensaios de liberação, além de evitar possíveis erros na determinação da espécie abordada. / The world population growth implies an increasingly search for a productive and sustainable agriculture. This requires the use of nutrient so that there is proportionality between the application and the demand for fertilizer demand. Thus, there is a growing search for coating materials, so that, when applied on the surface of solids, to control the release of fertilizers or even species of an active principle for the control of pests and diseases. So, it reduces the amounts used in soil and plants, with a major impact on reducing costs and undesirable drift effects and excesses in the applications, making it the most economical and environmentally sustainable practical agricultural. One of the most important applications of coating materials in agriculture consists on coating or encapsulation of urea. This mineral input is useful because of its high nitrogen content (between 43 to 46% by mass). However, it has a disadvantage due to losses by volatilization and lixiviation (about 17 to 50%), leading to a loss that reaches 50%. This study aims to develop and evaluate systems of polymeric coatings using polyurethane (PU) for controlled release urea. The experimental procedure was divided into three steps: (i) preparation and characterization of materials for coating based on derivatives of castor oil and soybean oil polyols; (ii) development of a measuring cell with control of physical and geometrical parameters as well as a system of thermal control and agitation; (iii) execution of release tests in water to check the influence of the percentage of PU in release rate as the diffusion kinetics and retention time. From the characterization of coatings is noted that the castor-based materials have better adherence to urea allowing better results in retention of macronutrient. Release tests showed that increasing the percentage of polymer retards the release rate of urea whereas tests using 5% extended release for up to 40 days. Also, it is observed that there is an optimum range of coating with values higher than 7% (PU castor oil) does not influence the release as confirmed from the Peppas modulation showing lower values for the kinetic of release these materials. Finally, the measuring cell designed to adapt and to standardize procedures involving controlled release allowed maximum control of physical and geometrical parameters in the tests being an excellent tool to release assays and avoid possible errors in determination of studied species.

Misturas de ureia (U) e ureia revestida com enxofre e polímero (URP) podem ser uma alternativa para melhorar a eficiência de utilização de nitrogênio (EUN) e reduzir custos quando aplicadas de uma única vez em cultivos agrícolas. Em experimentos de campo foram investigados diferentes índices de EUN (eficiência de recuperação aparente (ERA), eficiêncica fisiológica (EF), eficiência de utilização interna (EUI), eficiência agronômica (EA) e fator parcial (FPP) do N aplicado) e o acúmulo e particionamento de macronutrientes no milho (Zea mays L.) com misturas de U e URP na dose de 180 kg ha-1 aplicados totalmente na semeadura em Latossolo Vermelho Amarelo distrófico (LVAd) e Latossolo Vermelho distrófico (LVd). Foi incluído tratamento com ureia em manejo convencional (UMC). As misturas de URP+U foram incorporadas em faixa, 5 cm abaixo e 10 cm ao lado da linha de semeadura. As plantas foram amostradas em quatro estádios e divididas em quatro frações da planta (partes da planta) para a determinação de nutrientes. No LVAd, tratamentos com 100%URP, 70%URP+30%U e 60%URP+40%U apresentaram maior produtividade que o tratamento controle; 100%U e UMC tiveram menor EF e EUI que o 100%URP; todos os tratamentos com N apresentaram maior acúmulo total de N e massa seca que o controle em R6; a proporção de 70%URP+30%U apresentou maior acúmulo de S total do que o controle e UMC em R6. Não foram verificadas diferenças entre os tratamentos para produtividade, índices de EUN e acúmulo total de nutrientes no LVd. Em experimentos em casa de vegetação foram avaliados a condutividade elétrica (CE) e o pH do solo, altura, diâmetro, massa seca e acúmulo de N no desenvolvimento inicial de plantas de milho usando a mistura de 70%URP+30%U aplicada em faixa na semeadura do milho, das seguintes maneiras: 1) aplicando-se uma dose equivalente a 180 kg ha-1 de N em diferentes posições (5, 10 e 15 cm abaixo e 0, 5 e 10 cm ao lado da linha de semeadura) em um Latossolo Vermelho eutrófico (LVe) e comparando com 100%U; 2) variando as doses de N (equivalente a 0, 90, 180, 360 e 540 kg ha-1 de N) em uma posição considerada adequada (15 cm abaixo e 10 cm ao lado da linha de semeadura) no LVe e no LVAd. As aplicações feitas 15 cm abaixo da linha de semeadura apresentaram maior CE na linha do fertilizante na camada 9-18cm, pH na linha do fertilizante, massa seca total e N total que 5 e 10 cm. 70%URP+30%U apresentou maior altura, massa seca total e N total que 100%U quando aplicados abaixo da linha de semeadura. Nas aplicações 10 cm ao lado da linha de semeadura observou-se menor CE na linha do fertilizante comparado com as de 0 cm. No LVAd, massa seca total e N total apresentaram comportamento quadrático em resposta ao aumento da dose de N. Misturas de U e URP são eficientes quando aplicadas na semeadura do milho e elevadas doses interferem no desenvolvimento inicial de plantas de milho mesmo em uma posição considerada adequada no LVAd. / Blends of urea (U) and polymer sulfur coated urea (PSCU) can be an alternative to improve nitrogen (N) use efficiency (NUE) and reduce costs when applied in a single application in agricultural crops. Different indices of NUE (apparent crop recovery applied N (RE), physiological efficiency of applied N (PE), internal utilization efficiency of N (IE), agronomic efficiency of applied N (AE), partial factor productivity of applied N (PFP)) were investigated in field experiments, as well as nutrient uptake and partitioning in corn (Zea mays L.) with blends of U and PSCU applied in a single application of 180 kg N ha-1 at sowing in a Typic Haplustox and Rhodic Haplustox. It was included a treatment with urea in conventional management (UCM). The blends of U and PSCU were incorporated in a band 5 cm below and 10 cm to the side of the seed row. Plants were sampled at four growth stages and divided into four fractions for nutrient determination. In the Typic Haplustox, treatments with 100%PSCU, 70%PSCU+30%U and 60%PSCU+40%U had higher grain yield than control treatment (without N application); treatments with 100%U and UCM had lesser PE and IE than 100%PSCU; all the N treatments had higher total biomass and total N uptake than control at physiological maturity (R6); treatment with 70%PSCU+30%U had higher total S uptake than control and UCM at R6. There weren\'t differences between treatments for grain yield, indices of NUE, and total nutrient uptake at R6 in the Rhodic Haplustox. In greenhouse experiments, electrical conductivity (EC) and pH of soil, height, diameter, dry weight and nitrogen uptake in early plant growth were evaluated using a blend of 70%PSCU+30%U applied in a band at sowing maize in the following ways: 1) applying a rate equivalent to 180 kg N ha-1 in different positions (5 , 10 and 15 cm below and 0, 5 and 10 cm to the side of the seed) in a Rhodic Eutrustox and comparing with 100%U; 2) varying rates (equivalent to 0, 90, 180, 360, 540 kg N ha-1) in a position considered adequate (15 cm below and 10 cm to the side of the seed) in a Rhodic Eutrustox and Typic Haplustox. The N fertilizer application 15 cm below of the seed had higher EC in fertilizer row at 9-18cm, pH in fertilizer row, total dry weight and total N uptake than 5 and 10 cm below of the seed. The treatment with 70%PSCU+30%U had higher height, total dry weight and total N uptake than 100%U in the application 0 cm to the side of the seed. The N fertilizer application 10 cm to the side of seed had lesser EC in the fertilizer row than 0 cm. In the Typic Haplustox, total dry weight and total N uptake had quadratic behavior in response to increase N rates. Blends of U and PSCU are efficient when applied at corn sowing and can affect early plant growth at high rates even in a position considered adequate in Typic Haplustox.

Fertilizantes de liberação controlada como a ureia revestida com polímeros podem propiciar melhor sincronia entre a disponibilidade de nitrogênio (N) no solo e as exigências do nutriente pela cultura de milho (Zea mays L.). Para avaliar o efeito de diferentes estratégias de uso da ureia revestida com polímeros na disponibilização de nitrogênio inorgânico, nitrato (NO3-) e amônio (NH4+) no solo durante o ciclo da cultura de milho, e na produtividade final de grãos, foram conduzidos experimentos na safra 2012/2013, em duas condições edafoclimáticas no município de Piracicaba, Estado de São Paulo. Os solos dos experimentos foram: Latossolo Vermelho Distrófico (LVd) e Latossolo Vermelho Amarelo Distrófico (LVAd). O delineamento experimental foi de blocos completos ao acaso com quatro repetições e os tratamentos constaram da aplicação da dose de 180 kg ha-1 de N, utilizando-se duas fontes de N, ureia revestida com polímeros e ureia convencional, aplicadas, respectivamente, nas proporções de 100:0, 90:10, 80:20, 70:30, 60:40, 50:50 e 0:100%, além de um tratamento com ureia em manejo convencional com aplicação parcelada (20% na semeadura e 80% em cobertura entre os estádios V4-V6), e o controle sem aplicação de N. Foi semeado híbrido de milho com elevado potencial de produtividade. Os fertilizantes aplicados na semeadura foram incorporados a 5 cm de profundidade e 10 cm ao lado da linha de milho. Para determinar o teor de nitrogênio inorgânico no solo, nas camadas de 0-0,1, 0,1-0,2, 0,2-0,4 e 0,4-0,6 m, foram realizadas amostragens na semeadura e em V4, V12 e R3 no LVd e na semeadura e em V6, V14 e R4 no LVAd. Produtividade de grãos, massa seca da parte aérea, acúmulo de N na parte aérea, exportação de N nos grãos, e a eficiência de utilização interna de nitrogênio foram avaliados na maturidade fisiológica da cultura. Os resultados foram submetidos à análise de variância e quando observado efeito significativo de tratamentos, foram realizadas análises de contraste de médias (p<=0,1). A produtividade máxima nos dois experimentos foi da ordem de 10 Mg ha-1 de grãos de milho. Nos dois experimentos a ureia revestida com polímeros disponibilizou nitrogênio mineral no solo ao longo de todo o ciclo da cultura de milho, o que resultou no LVAd em produtividade de grãos mais elevada em relação à utilização de ureia convencional, diferentemente do ocorrido no LVd, onde não foram observados efeitos de tratamentos. A utilização de misturas de URP e U na adubação da cultura do milho, com proporções variando de 100% a 50% da fonte de liberação controlada, mostrou-se eficiente e pode ser considerada uma estratégia que fornece N conforme a exigência da cultura, o que resulta em maior produtividade de grãos em condições edafoclimáticas favoráveis. / Controlled release fertilizers such polymer coated urea can provide better synchrony between nitrogen (N) availability in the soil and its requirements by maize (Zea mays L.). To evaluate the effect of different use strategies of polymer coated urea on the availability of inorganic nitrogen, nitrate (NO3-) and ammonium (NH4+) throughout the crop cycle, and the grain yield, field experiments were carried out in the 2012-2013 growing season, in two soil-climatic conditions, in Piracicaba, São Paulo State. The soils were a clayey and a sandy Oxisol. The experimental design was randomized blocks with four replications, and the treatments consisted of 180 kg N ha-1, using two sources of N, polymer coated urea and conventional urea, respectively, in proportions of 100:0, 90:10, 80:20, 70:30, 60:40, 50:50% and 0:100%, besides a treatment with urea in conventional management, split-applied (20% at seeding and 80% side-dressed in V4-V6 corn growth stage) and a control (without N). Maize hybrid with high productivity potential was used. The fertilizers applied at seeding were placed in bands 5 cm depth and 10 cm aside the corn row. To determine the inorganic nitrogen content in the soil at 0-0.1, 0.1-0.2, 0.2-0.4 and 0.4-0.6 m soil layers, samples were collected at seeding, V4, V12 and R3 corn growth stage in the clayey Oxisol, and at sedding, V6, V14 and R4 in the sandy Oxisol. Grain yield, aerial biomass, nitrogen uptake by the aerial biomass, grain nitrogen uptake and internal utilization efficiency of nitrogen were evaluated. Data were analyzed using analysis of variance and when differences were detected, means where separated using contrast test (p<=0.1). The maximum maize grain yield in the experiments was approximately 10 Mg ha-1. In the two experiments, polymer coated urea led to a greater inorganic nitrogen availability throughout the maize cycle, which resulted in higher yield comparing to the use of conventional urea in the sandy Oxisol, not thus in the clayey Oxisol, where no effects of treatments in grain yield were observed. The use of blends of polymer coated urea and conventional urea in maize fertilization, with ratios ranging from 100 to 50% of the controlled release source, was efficient and can be considered a strategy that supplies N as the crop demands it, and thus lead to a greater maize grain yield under agro-climatic favorable conditions.

Ce travail démontre l'utilité des propriétés photothermiques dans le proche Infrarouge (NIR) des complexes de nickel-bis(dithiolène) neutres pour des applications en science des matériaux et biotechnologies. Des complexes Ni-bis(dithiolène) neutres hydrophiles et hydrophobes ont été élaborés et leur effet photothermique, sous irradiation laser NIR, a été quantifié pour la première fois. Grâce à cette propriété remarquable et à leur grande stabilité sous irradiation, il a été mis en évidence, que ces complexes pouvaient trouver des applications pour la thérapie photothermique, la libération contrôlée de médicament mais également pour le développement de nanomatériaux photosensibles à un stimulus externe. En effet, cet effet photothermique, sous irradiation laser NIR, permet de détruire des cellules cancéreuses, d'augmenter la perméabilité de nanoparticules polymériques ou de liposomes contenant des principes actifs et de désagréger des métallogels à base de complexes Ni-bis(dithiolène). Enfin, nous avons montré que les complexes [Ni(R2-timdt)2]0 ayant une haute efficacité photothermique sont de nouveaux candidats très prometteurs pour ce type d'applications. / The photothermal properties in the near Infrared (NIR) of neutral nickel-bis(dithiolene) complexes were used in materials science and for the first time in biotechnology. Hydrophilic and hydrophobic neutral Ni-bis(dithiolene) complexes were developped and for the first time, their photothermal effect under NIR laser irradiation was quantified. Thanks to this remarkable property and their high stability under irradiaton, it has been demonstrated that these complexes could find applications to photothermal therapy, controlled drug delivery but also in the developpement of stimuli responsive nanomaterials. Indeed, this photothermal effect, under NIR laser irradiation, allow to destroy malignant cells, increase the permeability of polymeric nanoparticles or liposomes containing active ingredients and disintegrate métallogels based on Ni-bis(dithiolene) cores. Finally, we showed that the [Ni(R2-timdt)2]0 complexes having higher phothothermal activity are very promising new candidates for these applications.

Os comprimidos osmóticos do tipo bicamada ou \"push pull\" são sistemas reservatórios constituídos de um núcleo bicamada, circundado por uma membrana semipermeável e com um orifício de liberação perfurado a laser que permitem a liberação do fármaco através da cinética de ordem zero. Este sistema possui a vantagem de apresentar uma liberação controlada e não influenciada pelos fatores fisiológicos do trato gastrointestinal, permitindo aplicações terapêuticas para novos fármacos e inclusive para fármacos já existentes. O presente projeto contemplou as etapas de desenvolvimento, caracterização e avaliação de um sistema osmótico do tipo bicamada ou \"push pull\", para veiculação do atenolol, um beta bloquador de grande importância na terapia antihipertensiva. Após a padronização e validação da metodologia analítica, estudos de compatibilidade entre o fármaco e os excipientes através da análise calorimétrica e espectroscopia no infravermelho (pré-formulação), a produção, a caracterização da membrana de revestimento e, por fim, a avaliação do desempenho dos núcleos osmóticos foram realizados. Assim, três lotes, com 4kg cada, foram produzidos para determinação do peso médio e do ferramental adequados, além da proporção entre os excipientes da formulação. O processo de compressão deu origem aos núcleos osmóticos do tipo bicamada que foram submetidos à avaliação físico-química como determinação do peso médio, da dureza, da friabilidade e da espessura. Além disso, padronizou-se o processo de revestimento dos núcleos com membrana semipermeável e avaliou-se o perfil de captação de água dos núcleos resultantes (\"Swelling\"). A membrana de revestimento foi submetida à microscopia eletrônica de varredura (MEV), análise por adsorção de nitrogênio e porosimetria de mercúrio para verificação da distribuição e tamanho médio dos poros. Para a obtenção do orifício de liberação padronizou-se a quantidade de radiação a laser suficiente para perfuração da membrana semipermeável que envolve os núcleos. Após a perfuração a laser, os núcleos foram submetidos então ao estudo de liberação in vitro para avaliação da influência do diâmetro de orifícios, do número de orifícios, da espessura da membrana semipermeável, da hidrodinâmica do meio de dissolução e da influência térmica na velocidade de liberação do fármaco. A cinética do tipo ordem zero e o controle da liberação do fármaco ao longo do tempo foram alcançados com sucesso a partir dos núcleos osmóticos produzidos no lote 03. / The push pull osmotic release tablets are bilayer core reservoir systems surrounded by semi permeable membrane and with one delivery hole where the drug is released through, following zero order release kinetics. This system has many advantages and two of them are the controlled drug release and independence of physiologically factors allowing many therapeutic applications to new one and known one drugs. This exclusive work proposed the development, characterization and evaluation of atenolol push pull osmotic system that is very important to antihypertensive treatment. After analytical standardization and validation activities, the pre-formulation studies using calorimetric and infra red spectroscopy techniques, manufacturing, semi permeable membrane characterization and finally osmotic tablets performance evaluation were performed. Batches about 4 kg each one were manufactured and tablets average weight, by-layer proportionality and suitable punches were chosen. Thus the osmotic tablets obtained by bi-layer press were physical and chemical evaluated (average weight, hardness, friability, and thickness). After that the tablets were submitted to a coating process with semi permeable membrane and the uptake water profile (Swelling) was observed to characterize the membrane permeability. The semi permeable membrane was submitted also to scanning electron microscopy (SEM), nitrogen adsorption and mercury porosimetry techniques in order to characterize the porous average diameter and distribution. To produce the delivery hole in the drug layer semi permeable membrane the sufficient laser radiation amount was studied and determined. So the perforated osmotic tablets were submitted to in vitro drug release studies to evaluate the influence of hole diameter, hole number, coating thickness, medium hydrodynamic and temperature stress responsible for drug release modifications. Finally the controlled delivery and the zero order drug release kinetics were achieved successfully from osmotic tablets developed and produced in the third bath. This third bath was the result of the factors comprehension and the optimization of the early ones.

L’objectif de cette thèse était de réaliser des désodorisants, obtenus à partir de différentes essences naturelles. Ceux-ci doivent être efficaces dans l’amélioration du microclimat des atmosphères de travail. Une étude fondamentale sur l'optimisation de l'extraction des essences naturelles et l'identification des composants de ces essences a été réalisée par GC/MS. Nous avons étudié également les processus de reconnaissance moléculaire entre les composants majoritaires de ces essences et des CDs natives ou modifiées. La stabilité de ces complexes a été mesurée par trois méthodes différentes : l’headspace statique, la spectrophotométrie UV-visible et la microcalorimétrie de titration isotherme. La réalisation d’adsorbants à base de cyclodextrines a été effectuée en utilisant des polymères de cyclodextrine synthétisés à partir de l’épichlorhydrine ainsi que des matériaux hybrides de type CM-β-CD/LDH. L’efficacité des désodorisants obtenus a été évaluée en mesurant la durée de libération des composés odorants. / The objective of this thesis was to develop air fresheners from various natural essences. Those must be efficient in the improvement of working atmosphere microclimate. A fundamental study on the optimization of extraction of natural essences andidentification of components of these essences was performed by GC/MS. We have also studied the process of molecular recognition between the major components of these essences and native or modified CDs. The stability of these complexes was measured by three different methods: static headspace, UV-visible spectrophotometry and isothermal titration microcalorimetry.The realization of adsorbents supports based on cyclodextrins was carried out by using cyclodextrin polymers synthesized from epichlorohydrin and hybrid materials of CM-β-CD/LDH type. The efficiency of air fresheners was evaluated by measuring the release time of odorous compounds.

The thrust of this thesis is to study oral solid dosage formulation using hot melt coating method and to use pharmacokinetic modeling and simulation (PK M&S) as a tool that can help to predict pharmacokinetics of a drug in human and the probability of passing various bioequivalence criteria of the formulation based on the PK of the drug. Hot-melt coating using a new method, direct blending, was performed to create immediate and sustained release formulations (IR and SR). This new method was introduced to offer another choice to produce IR and SR drug delivery formulations using single and double coating layer of waxes onto sugar beads and/or drug loaded pellets. Twelve waxes were applied to coat sugar cores. The harder the wax the slower the drug was released from single coated beads. The wax coating can be deposited up to 28% of the weight of the core bead with 58% drug loading efficiency in the coating The cores were coated with single or double wax layers containing acetaminophen. Carnauba wax coated beads dissolved in approximately 6 hrs releasing 80% of loaded drug. However, when covered with another layer, the drug loaded beads released drug for over 20 hrs. When drug loaded pellets were used as cores, 33-58% drug loading was achieved. Double coated pellets exhibited a near zero order drug release for up to 16 hrs. Hot melt coating by direct blending using waxes is a simple process compared to conventional hot melt coating using coating pan or fluid bed coating machines. It offers an alternative way of making immediate, sustained drug release (IR, SR) and modified release (IR+SR) oral dosage forms of drugs which are stable at high temperature (100°C). The pellet-containing-drug coated formulations provide options when higher drug loading is warranted. It is required by the US Food and Drug Administration (FDA) that a new modified –release (MR) product or identical generic product be regarded as bioequivalent (BE) to the originators reference drug product. However, there are concerns that current regulatory criteria are not sufficient when evaluating bioequivalence (BE) for many MR products, and additional metrics for BE assessment of the products should be applied to ensure therapeutic equivalence. This study used pharmacokinetic modeling and simulation (M&S) to investigate 1) the probability of BE occurring between the MR test and reference products 2) the rates of false positive and true negative of the BE test; and 3) the estimation of the sample size in pivotal BE studies; all of which when partial area under the curves (pAUCs) were applied as additional BE criteria. Reference data of two MR forms of methylphenydate HCl (MPH) were simulated and obtained from literature (formulation Q and Metadate CD, respectively). Monte Carlo simulations were performed to simulate the test drug concentration profiles and BE assessment was carried out utilizing the mean (method 1) and individual concentration time curves (method 2). For formulation Q, adding pAUC₀₋[subscript Tmax] to current BE criteria reduced the possibility of passing BE from approximately 98% to 85%, with a true negative rate of 5%. The earlier the time points used to determine for pAUC before Tmax, the lower the chance of passing BE for the test product. The possibility of passing BE varied and depended on the coefficient of variations (CV) of T[subscript lag], K[subscript a] and K[subscript e] and that considerable variability in the parameters affected the earlier segments of the drug concentration profile curves more. Similar drug concentration time profiles between the test and reference products is recommended to ensure bioequivalence occurs with a reasonable subject sample size. A similar scenario was seen when Metadate CD was used as the reference product. PK M&S can help provide appropriate additional metrics to assure the BE test is a better tool ensuring therapeutic equivalence for MR products with little negative impact to generic manufacturers. Predictions can also be made about the required sample size and the chances of passing BE with any addition to the conventional three criteria for the test product. PK M&S was also used to predict drug concentrations of levofloxacin in tissue. Levofloxacin has been widely used in clinical practice as an effective broad-spectrum antimicrobial, however tendonitis and tendon rupture have been reported with increasing use of this agent. Here, these incidents will be assessed by investigating pharmacokinetic behavior of the compound to see if they are related to drug's tissue disposition. The PK model for levofloxacin was established. Mean concentration time profiles of single or multiple dosing of 500 mg levofloxacin following oral and IV infusion administration were simulated. Monte Carlo simulation was used to simulate the drug concentration time profiles in plasma (compartment 1) and tissue (compartment 2) after seven dosing regimens while varying the drug's elimination and distribution rates to see the effect of changing those rates have on the drug accumulation in tissue. Monte Carlo Simulation shows that low elimination rates affect the drug concentration in plasma and tissue significantly with the level in plasma rising up to 35 μg/mL at day 7. A normal elimination rate together with escalation of distribution rates from plasma to tissue could increase the tissue concentration after 7 doses to 9.5 µg/mL, a value that is more than twice that of normal. PK M&S can be used as an effective tool to evaluate drug concentration in different compartments (plasma and tissues, for example). The unexpectedly high concentration values in some cases may explain, at least in part, the reason of tendinopathy occurs in the clinical setting. / Graduation date: 2012 / Access restricted to the OSU Community at author's request from June 7, 2012 - June 7, 2014

Stable single-unit recordings from the nervous system using microelectrode arrays can have significant implications for the treatment of a wide variety of sensory and movement disorders. However, the long-term performance of the implanted neural electrodes is compromised by the formation of glial scar around these devices, which is a typical consequence of the inflammatory tissue reaction to implantation-induced injury in the CNS. The glial scar is inhibitory to neurons and forms a barrier between the electrode and neurons in the surrounding brain tissue. Therefore, to maintain long-term recording stability, reactive gliosis and other inflammatory processes around the electrode need to be minimized. This work has succeeded in the development of neural electrode coatings that are capable of sustained release of anti-inflammatory agents while not adversely affecting the electrical performance of the electrodes. The effects of coating methods, initial drug loadings on release kinetics were investigated to optimize the coatings. The physical properties of the coatings and the bioactivity of released anti-inflammatory agents were characterized. The effect of the coatings on the electrical property of the electrodes was tested. Two candidate anti-inflammatory agents were screened by evaluating their anti-inflammatory potency in vitro. Finally, neural electrodes coated with the anti-inflammatory coatings were implanted into rat brains to assess the anti-inflammatory potential of the coatings in vivo. This work represents a promising approach to attenuate astroglial scar around the implanted silicon neural electrodes, and may provide a promising strategy to improve the long-term recording stability of silicon neural electrodes.