Spelling suggestions: "subject:"ammonification"" "subject:"personification""
1 |
Bioaugmentation and Retention of Anammox Granules to a Mainstream Deammonification Bio-Oxidation Pilot with a Post Polishing Anoxic Partial Denitrification/Anammox Moving Bed Biofilm ReactorCampolong, Cody James 25 March 2019 (has links)
The Chesapeake Bay watershed has seen an increase in population, nutrient loading, and stringent effluent limits; therefore, cost-effective technologies must be explored and implemented to intensify the treatment of regional wastewater.
This work describes the bioaugmentation and retention of anammox (AMX) granules in a continuous adsorption/bio-oxidation (A/B) mainstream deammonification pilot-scale process treating domestic wastewater. The AMX granules were collected from the underflow of a sidestream DEMON® process. The bioaugmentation rate was based on several factors including full-scale sidestream DEMON® wasting rate and sidestream vs mainstream AMX activity. The retention of bioaugmented AMX granules required a novel settling column at the end of the deammonification step. The settling column was designed to provide a surface overflow rate (SOR) that allowed dense AMX granules to settle into the underflow and less dense floccular biomass to outselect into the overflow. B-Stage was operated to out-select nitrite oxidizing bacteria (NOB) by maintaining an ammonia residual (>2 mg NH4-N/L), a relatively high dissolved oxygen (DO) (>1.5 mg O2/L) concentration, an aggressive solids retention time (SRT) for NOB washout, and intermittent aeration for transient anoxia. AMX activity was not detected in the mainstream at any time. The settling column AMX retention quantification suggested but did not confirm AMX were maintained in the mainstream. NOB were not suppressed during this study and no nitrite accumulation was present in the mainstream process. It was theorized that AMX granules were successfully settled into the settling column underflow and accumulated in the intermittently mixed sidestream biological phosphorus reactor (SBPR) where they disintegrated.
This work also describes optimization of carbon addition to an anoxic partial denitrification anammox (PdN/A) moving bed biofilm reactor (MBBR) testing glycerol, acetate, and methanol as carbon sources to maximize total inorganic nitrogen (TIN) removal through the anammox pathway and to minimize effluent TIN. A carbon feeding strategy was developed and was evaluated by the extent of partial denitrification vs full denitrification (partial denitrification efficiency, PdN efficiency). All three carbon sources were capable of high TIN removal, low effluent TIN, and moderate to high PdN efficiency. Average TIN removal for glycerol was 10.0 ± 3.6 mg TIN/L, for acetate it was 8.7 ± 2.9 mg TIN/L, and for methanol it was 11.5 ± 5.6 mg TIN/L. Average effluent TIN for glycerol was 6.0 ± 4.0 mg TIN/L, for acetate it was 5.0 ± 1.1 mg TIN/L, and for methanol it was 4.3 ± 1.5 mg TIN/L. Average PdN efficiency for glycerol was 91.0 ± 9.0%, for acetate it was 88.0 ± 7.7%, and for methanol it was 74.0 ± 8.5%. When PdN efficiency was factored into the cost of each carbon source, methanol was 5.83% cheaper than glycerol per mass TIN removed and 59.0% cheaper than acetate per mass TIN-N removed. / Master of Science / The Chesapeake Bay watershed has seen an increase in population, nutrient loading, and stringent effluent limits; therefore, cost-effective technologies must be explored and implemented to intensify the treatment of regional wastewater. This work involves removing nitrogen from wastewater in a pilot sized modeled from a real wastewater treatment plant. The removal of nitrogen from wastewater can become costly. This cost is due to aeration and chemical demands to remove the nitrogen. This masters work uses a type of microorganism that can remove nitrogen without the need for aeration or chemicals through anaerobic ammonia oxidation (AMX bacteria).
A specific environment has been created for AMX bacteria during this study to ensure they perform nitrogen removal optimally. Often times, communities of bacteria can help remove nitrogen more effectively when they work together. Therefore, communities of bacteria were encouraged to grow during this study. We were able to see that nitrogen removal was indeed occurring at high rates and producing high effluent water quality. We used several different metrics to prove this nitrogen removal technology worked well. This research was important because it showed the capabilities of a highly intensified process of successful nitrogen removal at a pilot-scale facility. It is the hope that these findings can be improved upon and implemented at full-scale facilities. These full-scale facilities would be able to achieve low levels of nitrogen in their effluent while saving millions of dollars on operational costs.
|
2 |
Anammox-based systems for nitrogen removal from mainstream municipal wastewaterMalovanyy, Andriy January 2017 (has links)
Nitrogen removal from municipal wastewater with the application of deammonification process offers an operational cost reduction, especially if it is combined with a maximal use of organic content of wastewater for biogas production. In this thesis, two approaches for integration of the deammonification process into the municipal wastewater treatment scheme were studied. The first approach is based on ammonium concentration from municipal wastewater by ion exchange followed by biological removal of ammonium from the concentrated stream by deammonification process. Experiments with synthetic and real municipal wastewater showed that strong acid cation resin is suitable for ammonium concentration due to its high exchange capacity and fast regeneration. Since NaCl was used for regeneration of ion exchange materials, spent regenerant had elevated salinity. The deammonification biomass was adapted to NaCl content of 10-15 g/L by step-wise salinity increase. The technology was tested in batch mode with 99.9 % of ammonium removal from wastewater with ion exchange and up to 95 % of nitrogen removal from spent regenerant by deammonification process. The second studied approach was to apply anammox process to low-concentrated municipal wastewater in a moving bed biofilm reactor (MBBR) and integrated fixed film activated sludge (IFAS) system without a pre-concentration step. After a 5 months period of transition to mainstream wastewater the pilot plant was operated during 22 months and stable performance of one-stage deammonification was proven. Clear advantage of IFAS system was shown. The highest stable nitrogen removal efficiency of 70 % and a nitrogen removal rate of 55 g N/(m3·d) was reached. Moreover, the influence of operation conditions on competition between ammonium oxidizing bacteria (AOB) and nitrite oxidizing bacteria (NOB) was studied by literature review, batch tests and continuous pilot plant operation. / <p>QC 20170309</p>
|
3 |
Nitrous oxide emissions from deammonification process under different operation conditions.Mazurek, Agnieszka January 2015 (has links)
Wastewater treatment plays significant role in the environmental protection. The process has direct impact on quality of air and water. All treated sewage reaches fresh water reservoirs as well as gasses escaping from the process are emitted to the atmosphere. Main aim of the thesis is to determine N2O emissions from partial nitritation/Anammox (deammonification process) in one-stage system applied in MBBR technology. Whole project was operated successfully on two pilot-scale reactors parallel, fed by the same reject water. Both reactors were filled to capacity of 200 L each, where 40% of the working volume was fulfilled by Kaldnes carriers suspended in liquid by mechanical stirrer. First reactor (R1) presented strategy of intermittent aeration with ratio (R=1/3) and stable DO concentration at amount of 1.5 mg O2/L, whereas second one (R2) operated in constant aeration with variable values of dissolved oxygen which differ in range of 1.0-2.5 mg O2/L. Every week analyses of ammonium and nitrogen forms were carried out in influent and effluent by Hach-Lange cuvettes. Results of measurements showed high NH4+-N removal efficiency of approximately 95% for R1 reactor and 86% for R2. During the process, the continuous measurement of nitrous oxide in gaseous and liquid phase was performed by Teledyne data logger and Unisense microsensor. Measurements during 4 months resulted in assessment of nitrous oxide emission tendency dependent on aeration system. The result from reactor R1 showed that 1.0-2.4% of N-load was emitted as N2O to the atmosphere, and 0.05-0.28% was released as dissolved N2O in outgoing water. Regarding reactor R2 tendency of nitrous oxide production is similar. Estimated emission of N2O in gaseous phase in reactor R2 is 1.4-2.0% of nitrogen load and 0.02-0.39% in liquid phase. All gathered results are shown in the appendix of the paper.
|
4 |
Evaluation of Deammonification process operated at low temperatures.Rajkowski, Mariusz January 2012 (has links)
Anammox process is happening to be in the center of interest for several years. Implementing partial nitrification/Anammox process into main stream of wastewater would result in a great improvement of sustainable technologies for reducing nitrogen in environment. However, Great chalange fo Anammox bacteria in main stream is the low temperature which is a strong inhibiting factor for them. In this study pilot-scale MBBR reactor was operated to investigate the influence of low temperatures in Anammox process. Two different phases operated at 13 and 16°C were investigated during five months. SAA, OUR and online measurements were used to observe process capacity in low temperatures. Deammonification process was found to be stable in 13°C. Moreover, Anammox bacteria capacity to convert nitrogen to nitrogen gas was found in even 5°C. Satisfactory results for Deammonification process in low temperatures may result in future application of Anammox process in full-scale plant for main stream of wastewater.
|
5 |
Partial Nitration/anammox process in the moving bed biofilm reactor operated at low temperaturesSultana, Razia January 2014 (has links)
<p>QC 20140527</p>
|
6 |
The Investigation of Nitrite Accumulation and Biological Phosphorus Removal in an Intermittently Aerated Process Combining Shortcut Nitrogen Removal and Sidestream Biological Phosphorus RemovalPrintz, Kathryn Elizabeth 22 November 2019 (has links)
The research in this thesis was conducted at the Hampton Road Sanitation District's biological nutrient removal pilot, located at the Chesapeake-Elizabeth WWTP in Virginia Beach, VA. The pilot is operated in an A/B process with a high-rate, carbon-diverting A-stage, followed by a biological nitrogen removal B-stage containing four intermittently aerated CSTRs, followed by an anammox polishing MBBR. The goal of this research was to successfully combine short-cut nitrogen removal with sidestream enhanced biological nutrient removal (EBPR) in the most efficient way possible, specifically aiming to decrease cost and energy requirements, divert the most amount of carbon possible before B-stage, and to achieve low effluent nitrogen and phosphorus concentrations.
A RAS fermenter (SBPR) and an A-stage WAS fermenter that feeds VFA into the SBPR (the supernatant of the fermenter is called fermentate) were implemented in order to enhance biological phosphorus removal. About 8 months after the RAS and WAS fermenter implementation, there was a 28 day consecutive period of low B-stage effluent OP <1 mg/L, with an average of 0.5 ± 0.1 mg/L OP. Following this low effluent OP period, bio-P became more unstable and there was high nitrite accumulation in the B-stage effluent for 106 days with concentrations ranging from 1.1-5.9 mg/L NO2. The nitrite accumulation was not due to NOB out-selection, confirmed by AOB and NOB maximum activity tests. It was determined that the nitrite accumulation was due to partial denitrification of nitrate to nitrite by bacteria using internally stored carbon, because profiles and activity tests showed anoxic nitrite accumulation at the end of the aerobic process. Post-anoxic denitrification using internally stored carbon compounds has been observed in other EBPR systems (Vocks, Adam, Lesjean, Gnirss, and Kraume, 2005).
Fermentate addition was then halted, and nitrite accumulation and bio-P activity ceased all together, linking the fermentate addition to both bio-P activity and nitrite accumulation. Fermentate was then controlled to dose at 60% of the sCOD/OP (fermentate sCOD g/day / total OP- fermentate + influent - g/day) of the first low effluent OP period. During this fermentate dosing period where the average sCOD/OP was 15.6 ± 3.0 g/g, no nitrite accumulation was observed, but another consecutive low effluent OP period was observed with an average of 0.6 ± 0.2 mg/L OP.
Linear correlation analysis shows that the highest r2 values relating the low effluent OP periods and the COD loads to the SBPR for both periods were between VFA g/day vs OP effluent mg/L, at r2=0.18 for the first low effluent OP period and r2=0.65 for the second. There were also high tCOD r2 values for the second low effluent OP period showing that COD hydrolysis in the SBPR could have impacted bio-P activity. However, the VFA r2 value was higher than any tCOD r2 value, concluding that the fermentate dosing mainly worked to enhance biological phosphorus removal by increasing the VFA load in g VFA as acetate/day. Since no nitrite was observed in a period with a lower VFA/OP dose, then the probable VFA load needed to provide enough internal storage to produce nitrite accumulation by partial denitrification is between 5-9 (g VFA as acetate/ g total OP). If sidestream EBPR systems could be studied further to promote nitrite accumulation and bio-P activity to produce low effluent OP, then short-cut nitrogen removal and EBPR could be successfully combined in an efficient way. / Master of Science / It is important to reduce nitrogen and phosphorus concentrations in wastewater treatment effluent in order to both protect the environment from eutrophication and to meet the increasingly stringent nutrient effluent discharge limits imposed by the EPA. Conventional biological nitrogen removal is achieved through nitrification and denitrification converting ammonia to nitrogen gas, where nitrogen gas is volatile and leaves the system naturally. Phosphorus removal can be achieved through either chemical addition or through biological phosphorus removal, where phosphorus is taken up in cells and removed from the system by the subsequent solids wasting of these cells. The combination of biological nitrogen and phosphorus removal can be improved to increase energy efficiency, reduce costs including aeration and chemical addition costs, increase system capacity and reduce tank sizes, and reduce biomass production, all while achieving low effluent N and P concentrations.
Short-cut nitrogen removal can increase the efficiency of biological nitrogen removal. Deammonification, the combination of partial nitritation and anammox, has the potential to reduce wastewater treatment plant (WWTP) aeration costs by 63%, carbon requirements by 100%, and biomass production by 80% (Nifong, Nelson, Johnson, and B. Bott, 2013). Deammonification is the combination of partial nitritation and anammox. Anaerobic ammonia oxidation (anammox) is a useful class of bacteria that converts ammonia and nitrite straight to nitrogen gas in anaerobic conditions, which is a more direct pathway than the conventional nitrification-denitrification pathway. Anammox requires a nitrite supply, which can supplied by partial nitratation of ammonia to nitrite, performed by ammonia oxidizing bacteria (AOB) aerobically in the deammonification process. In order for partial nitratation to work, there needs to be nitrite oxidizing bacteria (NOB) out-selection so that the nitrite produced by AOB does not get oxidized to nitrate.
Enhanced biological phosphorus removal (EBPR) is accomplished by the taking up and storing of orthophosphate (OP) by phosphorus accumulating organisms (PAOs). These organisms require an anaerobic carbon-storage phase followed by an aerobic growth phase where the internally stored carbon is used for growth. During the cell growth phase of PAOs in aerobic conditions, PAOs are able to take up more OP than they previously released in anaerobic conditions, creating a net OP removal from the system. There has been recent success in recycle activated sludge (McIlroy et al.) fermentation to enhance biological phosphorus removal, which works to promote hydrolysis, fermentation, and EBPR enhancement (Houweling, Dold, and Barnard, 2010). A portion of the RAS is introduced to an anaerobic zone before returning to the main process, allowing for extra VFA production and adsorption by PAOs. RAS fermentation solves the issue of carbon needed for EBPR in VFA/carbon limited systems without having to add too much additional carbon, creating a carbon efficient EBPR system.
The research outlined in this study was done at the Hampton Road Sanitation District's (HRSD) pilot plant located within HRSD's Chesapeake-Elizabeth WWTP in Virginia Beach VA. The pilot is run in an A/B process that works in two separate steps: the A-stage is the first step that works to remove carbon by oxidation, and by adsorption so it can potentially be diverted, and the B-stage is the second step where biological nitrogen removal (BNR) is done. The BNR phase consists of an anaerobic selector followed by four completely stirred tank reactors (CSTRs) that are intermittently aerated to provide aerobic and anoxic phases. The pilot also has an anammox polishing step following B-stage. The nitrogen removal goal for this research was short-cut nitrogen removal via deammonification, by producing partial nitritation in B-stage and polishing with anammox. A B-stage RAS fermenter, along with an A-stage waste activated sludge (WAS) fermenter that feeds VFA into the RAS fermenter, was implemented to the existing pilot to enhance biological phosphorus removal. The overall goal of this study was to successfully combine short-cut nitrogen removal with sidestream EBPR to achieve low effluent N and P concentrations in the most energy and carbon efficient way possible.
EBPR was achieved about eight months after the implementation of the RAS and WAS fermenter to the pilot. A period of B-stage effluent OP that was consistently below 1 mg/L OP was observed right before an unexpected period of high nitrite in the B-stage effluent. The high effluent nitrite lasted for 106 days and ranged from 1.1-5.9 mg/L of effluent nitrite during this time. The nitrite accumulation was unexpected because weekly maximum activity tests for AOB and NOB showed that NOB out-selection was not occurring. The first phase of this research investigates the cause of the nitrite accumulation. Based on profiles taken in the reactors in the aerobic and anoxic phases, and based on denitrification activity tests, it was determined that the nitrite accumulation was due to partial denitrification of nitrate to nitrite. Because this partial denitrification was happening in the reactor anoxic times where external should have been used up, it was determined that the source of the partial denitrification was from a bacteria using internally stored carbon during anoxic periods as the electron supply for partial denitrification. Research has showed that EBPR systems promote bacteria that are capable of storing carbon internally and keeping that carbon stored through an aerobic phase and then using that stored carbon for denitrification following an aerobic phase (Vocks et al., 2005), like observed in this research.
The second phase of this research sought to link the nitrite accumulation and bio-P activity to the VFA added to the RAS fermenter. The VFA addition was decreased in phases, and with that a decrease in nitrite in the effluent was observed. The bio-P activity became more unstable after the nitrite accumulation occurred, but all bio-P activity ceased after VFA addition to the RAS fermenter ceased. It was concluded, unsurprisingly, that the VFA added to the RAS fermenter was the source of the internally stored carbon that caused the nitrite accumulation, and necessary for bio-P enhancement.
The third phase of this research sought to recreate the low effluent OP period and the nitrite accumulation by controlling the VFA dose to the RAS fermenter. The average soluble chemical oxygen demand (sCOD) per OP (fermenter sCOD g/day / total OP-fermenter + influent- g/day) of the period of low effluent OP was calculated, and the dose from the WAS fermenter was controlled to meet 60% of the calculated value. The calculated dose was 13.6 gC/gP, but the actual average dose from controlling the load during this period was 15.6 ± 3.0 gC/gP. The average VFA/OP (g VFA as acetate/ g total OP) dose for the first low effluent OP period was 9.4 ± 3.6 g/g, and the average dose for the third phase of research was 5.5 ± 1.3 g/g. No nitrite accumulation occurred in this phase, but another consistent low effluent OP period did occur. From linear correlation analysis, the highest r2 values relating the low effluent OP periods and the COD loads to the RAS fermenter for both periods were between VFA g/day vs OP mg/L, at r2=0.18 for the first period and r2=0.65 for the second. This shows that effluent OP < 1 mg/L can be achieve at 5.5 or 9.4 (g VFA as acetate/ g total OP). Since no nitrite was observed in phase 3, than the probable VFA load needed to provide enough internal storage to produce nitrite accumulation by partial denitrification is probably between 5.5-9.4 (g VFA as acetate/ g total OP).
This research was significant because the link between nitrite accumulation and bio-P enhancement with sidestream RAS and WAS fermentation was confirmed. Partial denitrification of nitrate to nitrite could be used as an alternative source of nitrite for anammox, instead of NOB out-selection and partial nitritation of ammonia to nitrite by AOB, in combined EBPR and short-cut nitrogen removal systems. If sidestream EBPR systems could be used to promote nitrite accumulation and bio-P activity to produce low effluent OP and nitrogen removal efficiently than short-cut nitrogen removal and EBPR could be successfully combined in an efficient way. Future work needs to be done on the organism that is capable of nitrite accumulation and if that organism can be enhanced in conjunction with EBPR organisms to promote both nitrite accumulation and low effluent OP simultaneously.
|
7 |
Kväverening av rejektvatten genom deammonifikation eller adsorption med biokol : En studie för Arvidstorps avloppsreningsverk i Trollhättan / Nitrogen Removal from Reject Water by Deammonification or Adsorption with Biochar : A Study made for Arvidstorp's Waste Water Treatment Plant in TrollhättanNordebring, Sara January 2019 (has links)
Ett av riksdagens miljömål är att minska övergödande faktorer. En källa till övergödning är kväveutsläpp från avloppsreningsverk. Arvidstorps avloppsreningsverk i Trollhättan väntar en ökad inkommande belastning på grund av befolkningsökning i området samt skarpare krav på utgående halt utsläppt kväve. Detta innebär att planer på att bygga en ny anläggning har satts i verket för att kunna hantera den ökande belastningen. Eventuellt kommer den nya anläggningen inte bli klar innan de nya kraven kommer. Detta gör att reningsverket utreder andra alternativ för att reducera kväve ur avloppsvattnet som kan tas i drift innan den nya anläggningen är klar. Ett alternativ till kväverening är att använda rejektvattenrening eftersom denna avloppsström innehåller höga koncentrationer kväve. Ett annat problem som reningsverket står inför är att kostnaderna för att hantera det avvattnade slammet förväntas öka. Reningsverket utreder därför alternativ för att minska slamvolymen. En biokolsanläggning där biokol tillverkas av det avvattnade slammet skulle kunna vara ett alternativ. Fördelen är att slamvolymen minskar samt att biokol kan användas som vattenrening då det har förmågan att adsorbera ämnen. I detta arbete har två olika tekniker för att rena kväve ur rejektströmmen på Arvidstorps reningsverk studerats. Dessa är dels en beprövad teknik som kallas deammonifikation där kväve renas med bakterier, och dels biokolsadsorption som kvävereningsmetod vilket inte är en lika etablerad reningsteknik på kommunala reningsverk. Deammonifikationsprocessen finns som flera olika tekniker där den som valts för detta arbete är ANITA Mox. ANITA Mox finns som två tillämpningar där den ena är MBBR (Moving Bed Biofilm Reactor) och den andra är IFAS (Integrated Fixed Film Activate Sludge). Målet med detta arbete var att göra en investeingskalkylering för att bedöma hur ekonomiskt försvarbart det är att installera ANITA Mox MBBR eller ANITA Mox IFAS samt uppskatta kvävereningskapaciteten för alternativet med biokolsadsorption. Inga ekonomiska aspekter togs hänsyn till för det senare alternativet. För beräkningarna byggdes modeller i Excel och två olika experiment utfördes. Pyrolysering av rötrest till biokol och adsorption, samt ett luftningsförsök för att bestämma faktorer som krävs vid beräkning av luftbehov för deammonifikationsprocessen. ANITA Mox MBBR ha de lägsta årskostnaderna, trots att IFAS kan reducera mer kväve och därmed har lägre driftkostnader. IFAS kräver dessutom en mindre volym total sett med reaktor och sedimenteringsbassäng inräknat, men anledningen till den högre kostnaden är de extra instrument och komponenter som krävs till sedimenteringsbassängen med slamretur och den kortare livslängden på dessa komponenter som ger den högre årskostnaden. Biokol som reningsmetod är inte en lämplig metod då det krävs 66 gånger mer rötrest för att producera den mängd biokol som krävs för att rena rejektvattnet. Den rötrest som kommer produceras i en framtida anläggning kan endast reducera 1,5 % av kvävemängden. / One of the environmental goals for the Swedish parliament is to reduce eutrophic factors. A source of eutrophication is nitrogen emissions from waste water treatment plants. Arvidstorp's waste water treatment plant in Trollhättan expects a population increase and sharper requirements for outgoing nitrogen emissions. This means that plans to build a new plant have been put into operation in order to handle the increasing load. The new facility may not be ready before the new requirements come. The waste water treatment plant is therefore investigating other options for reducing nitrogen from the wastewater. An alternative to nitrogen removal is to use reject water purification since this sewage stream contains high concentrations of nitrogen. Another problem facing the waste water treatment plant is that the costs of handling the dewatered sludge is expected to increase. The treatment plant is therefore looking for alternatives to reduce the sludge volume. A biomass pyrolysis plant where biochar is produced by the dewatered sludge could be an alternative since the advantage is that the sludge volume is reduced and that biochar can be used as water purification as it has the ability to adsorb substances. In this work, two different techniques to remove nitrogen from the reject stream at Arvidstorp's treatment plant has been studied. One is a proven technique called deammonification where nitrogen is purified with bacteria, the other one is biochar adsorption as a nitrogen removal process, however not an equally established purification technique on municipal waste water treatment plants. Several different techniques exists as deammonification processes. The one chosen for this work is ANITA Mox. ANITA Mox is available as two implementations where one is MBBR and the other is IFAS. The goals of this work was to make an investment calculation to assess how economically justifiable it is to install either ANITA Mox MBBR or ANITA Mox IFAS and to estimate the nitrogen removal capacity of the alternative with biochar adsorption. No economic aspects were taken into account for the latter option. For the calculations, models were built in Excel and two different experiments were performed. Pyrolysis of digestion residue for biochar production and adsorption, as well as an aeration test to determine the factors required when calculating the air demand for the deammonification process. ANITA Mox MBBR has the lowest annual costs, even though IFAS can reduce more nitrogen and thus have a greater impact on operating costs. IFAS also requires a smaller reactor volume. The reasons for the higher cost are the extra instruments required for the sedimentation basin and the shorter life span of these components which gives the higher annual cost. Biochar as a purification method is not a suitable method as it requires 66 times more sludge to produce the amount of biochar required to purify the reject water. The sludge that will be produced in a future plant can only reduce 1.5% of the nitrogen load.
|
8 |
Study on one-stage Partial Nitritation-Anammox process in Moving Bed Biofilm Reactors: a sustainable nitrogen removal.Bertino, Andrea January 2011 (has links)
In the last decade, several novel and cost-effective biological nitrogen removal technologies have been developed. The discovery of anaerobic ammonium oxidation (Anammox), about 15 years ago, has resulted in new opportunities for research and development of sustainable nitrogen removal systems. Compared to conventional nitrification/denitrification, Anammox eliminates necessity of external organic carbon source, has a smaller production of excess sludge, reduces energy demand for aeration (up to 60-90%) and CO2 emissions (up to 90%). Systems based on Anammox can be of great help to comply with stricter wastewater discharge regulations and reduce environmental problems caused by nutrients discharges (e.g. eutrophication). This thesis investigates the partial nitritation/Anammox in one stage system under oxygen limited condi-tions (also called CANON or Deammonification) and with the Moving Bed Biofilm Reactor (MBBR™) technology. Anammox process coupled with partial nitritation can be particularly suitable to treat ammo-nium-rich wastewater with low content of biodegradable organic matter, such as the reject water from dewatering of digested sludge, which is usually recirculated back to the main stream of wastewater treat-ment plants, accounting for the 15-20% of the total nitrogen load. Partial nitritation/Anammox process was successfully tested on a pilot plant scale for four months at 25°C, in a 200 L Continuous Stirred Tank Reactor (CSTR), filled with 40% of Kaldnes media (model K1). At an Ammonium Surface Load (ASL) of 3.45 gN m-2d-1, the removal rate was about 2.85 gN m-2d-1. Removal efficiencies of 95%, 85% and 83% were respectively achieved for NH4+-N, inorganic nitrogen, and Total Nitrogen (TN). Bacteria activity was followed by batch tests such as Specific Anammox Activity (SAA), Oxygen Uptake Rate (OUR) and Nitrate Uptake Rate (NUR), which revealed an increase in activi-ty for Nitrosomonas and Anammox bacteria within the biofilm. Dissolved oxygen concentration in the bulk liquid was a crucial parameter, whereas pH and conductivity turned out to be two useful monitoring tools. Two laboratory-scale reactors were previously run for two months each, in order to evaluate the one-stage partial nitritation/Anammox process with a lower ASL. One reactor was fed with diluted reject water, whereas the other one treated the effluent from UASB (Up-flow Anaerobic Sludge Blanket) reactor after sand filtration. Fairly good efficiency (>75%) were reached but, however, in the last case the low ammo-nium nitrogen load could represent a problem for a stable full-scale installation and long-term growth of Anammox bacteria. Some suggestions for full-scale implementation and further research are proposed in the last chapter of this master thesis.
|
9 |
N2O emission in a full-scale partial nitrification/anammox process.Sambola, Alejandro January 2012 (has links)
The reduction of the emission of greenhouse gases to the atmosphere will be one of the challenges that society will have to face in the coming years. Until now, all efforts have been put in improving the properties of the discharged water in a wastewater treatment plant and the efficiency of the whole process. But little effort has been done in measuring and controlling the greenhouse gas emissions. For this reason, the production of nitrous oxide when treating wastewater has become of great concern. Several measurements in laboratory scale and full scale have been done and a wide range of results have been obtained. On the other hand, Himmerfjärden wastewater treatment plant has a deammonification plant for treating rejected water produced when dewatering sludge. It consists of an efficient technology where less energy is supplied and no extra carbon source is added. However, it is unknown the efficiency of this system in terms of nitrous oxide production. For this reason, an analysis was carried out from the 19th June to the 2nd of July. In the light of the results obtained, the deammonification process has obtained better results than conventional nitrification and denitrification in terms of nitrous oxide emissions.
|
10 |
Assessment of a partial nitritation/Anammox system for nitrogen removalGut, Luiza January 2006 (has links)
This thesis evaluates the performance of a deammonification system designed as a two-step tech-nology consisting of an initial partial nitritation followed by an Anammox process. Operation of a technical-scale pilot plant at the Himmerfjärden Wastewater Treatment Plant (Grödinge, Swe-den) has been assessed. Oxygen Uptake Rate (OUR) to evaluate the respiration activity of nitrifi-ers in the system and batch tests to assess reaction rates have also been applied in the study. It was found that the total inorganic nitrogen elimination strongly depended on the nitrite-to-ammonium ratio in the influent to the Anammox reactor, which was correlated with the per-formance of the partial nitritation phase. Therefore, a control strategy for oxidation of ammo-nium to nitrite has been proposed. Controlled oxygen supply to the partial nitritation reactor is obligatory to obtain a proper pH drop indicating oxidation of ammonia to nitrite at the adequate ratio. A very high nitrogen removal efficiency (an average of 84%) and stable operation of the system have been reached. Conductivity measurements were also used to monitor the system influent nitrogen load and the nitrogen removal in the Anammox reactor. The data gathered from the operation of the pilot plant enabled the use of multivariate data analysis to model the process behaviour and the assessment of the covariances between the process parameters. The options for full-scale implementation of the Anammox systems have been proposed as a result of the study. / QC 20101115
|
Page generated in 0.1045 seconds