Thesis (M. S.)--Electrical and Computer Engineering, Georgia Institute of Technology, 2008. / Committee Chair: John D. Cressler; Committee Member: John Papapolymerou; Committee Member: Shyh-Chiang Shen.

Made available in DSpace on 2014-10-09T12:35:13Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:56:04Z (GMT). No. of bitstreams: 0 / Dissertação (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

abstract: Transparent conductive oxides (TCOs) are used as electrodes for a number of optoelectronic devices including solar cells. Because of its superior transparent and conductive properties, indium (In) tin (Sn) oxide (ITO) has long been at the forefront for TCO research activities and high-volume product applications. However, given the limited supply of In and potential toxicity of Sn-based compounds, attention has shifted to alternative TCOs like ZnO doped with group-III elements such as Ga and Al. Employing a variety of deposition techniques, many research groups are striving to achieve resistivities below 1E-4 ohm-cm with transmittance approaching the theoretical limit over a wide spectral range. In this work, Ga-doped ZnO is deposited using pulsed laser deposition (PLD). Material properties of the films are characterized using a number of techniques. For deposition in oxygen at pressures >1 mTorr, post-deposition annealing in forming gas (FG) is required to improve conductivity. At these higher oxygen pressures, thermodynamic analysis coupled with a study using the Hall effect measurements and photoluminescence spectroscopy suggest that conductivity is limited by oxygen-related acceptor-like defects in the grains that compensate donors, effectively reducing the net carrier concentration and creating scattering centers that reduce electron mobility. Oxygen is also responsible for further suppression of conductivity by forming insulative metal oxide regions at the grain edges and oxygen-related electron traps at the grain boundaries. The hydrogen component in the FG is thought to passivate the intra-grain acceptor-like defects and improve carrier transport across these grain boundaries. Given this deleterious effect of oxygen on conductivity, depositions are performed in pure argon (Ar), i.e., the only oxygen species in the growth ambient are those ejected directly from the PLD solid source target. Ga-doped ZnO deposited in Ar at 200 °C and 10 mTorr have resistivities of 1.8E-4 ohm-cm without the need for post deposition annealing. Average transmittance of the Ga-doped films is 93% over the visible and near infrared (IR) spectral regions, but free carrier absorption is a limiting factor further into the IR. After annealing in FG at 500 °C, a 300 nm Ar film has a Haacke figure of merit of 6.61E-2 sq. ohm. / Dissertation/Thesis / Ph.D. Materials Science and Engineering 2011

abstract: Programmable Metallization Cell (PMC) is a resistance-switching device based on migration of nanoscale quantities of cations in a solid electrolyte and formation of a conducting electrodeposit by the reductions of these cations. This dissertation presents electrical characterization results on Cu-SiO2 based PMC devices, which due to the na- ture of materials can be easily integrated into the current Complimentary metal oxide semiconductor (CMOS) process line. Device structures representing individual mem- ory cells based on W bottom electrode and n-type Si bottom electrode were fabricated for characterization. For the W bottom electrode based devices, switching was ob- served for voltages in the range of 500mV and current value as low as 100 nA showing the electrochemical nature and low power potential. The ON state showed a direct de- pendence on the programming current, showing the possibility of multi-bit storage in a single cell. Room temperature retention was demonstrated in excess of 105 seconds and endurance to approximately 107 cycles. Switching was observed for microsecond duration 3 V amplitude pulses. Material characterization results from Raman, X-ray diffraction, Rutherford backscattering and Secondary-ion mass spectroscopy analysis shows the influence of processing conditions on the Cu concentration within the film and also the presence of Cu as free atoms. The results seemed to indicate stress-induced void formation in the SiO2 matrix as the driving mechanism for Cu diffusion into the SiO2 film. Cu/SiO2/nSi based PMC devices were characterized and were shown to have inherent isolation characteristics, proving the feasibility of such a structure for a passive array. The inherent isolation property simplifies fabrication by avoiding the need for a separate diode element in an array. The isolation characteristics were studied mainly in terms of the leakage current. The nature of the diode interface was further studied by extracting a barrier potential which shows it can be approximated to a Cu-nSi metal semiconductor Schottky diode. / Dissertation/Thesis / Ph.D. Electrical Engineering 2011

La détection et l'identification des substances biologiques ou chimiques peuvent être accomplies par des biocapteurs. On exige des biocapteurs d'être simple et rapide à utiliser, d'avoir une taille réduite, et d'être suffisamment sensible afin de pouvoir détecter des molécules en petite quantité. Des dispositifs plasmoniques se sont révélés adaptés pour l'usage en tant qu'élément transducteur des biocapteurs. Les plasmon-polaritons de surface (SPP) sont des oscillations collectives du nuage électronique des métaux, couplées à des ondes électromagnétiques. Leur fréquence de résonance dépend de l'indice de réfraction de leur environnement diélectrique. Ceci permet de sonder de manière efficace la présence des molécules par la modification de l'indice de réfraction engendrée par celles-ci. La technique reposant sur ce principe s'appelle la détection par résonance des plasmons de surface (SPR sensing en anglais). De plus, les SPP confinent le champ électrique incident à des volumes sub-longueurs d'onde et l'exaltent ainsi. Les molécules qui se situent dans ces zones de forte exaltation du champ électrique interagissent plus efficacement avec la lumière incidente par l'intermédiaire du SPP, tel que leur section efficace de l'absorption infrarouge (IR) augmente. La spectroscopie IR est une technique standard d'identification de molécules en quantités suffisantes. Pour améliorer la sensibilité, la spectroscopie vibrationnelle d'absorption exaltée par la surface (SEIRA pour surface enhanced infrared absorption en anglais) est particulièrement bien adaptée.Alors que la plasmonique s'est principalement développée dans le visible via les métaux nobles, les semi-conducteurs III-V fortement dopés présentent une alternative intéressante pour la plasmonique dans le moyen IR. Leur fonction diélectrique ressemble à celle des métaux nobles dans le visible, mais décalée dans le moyen IR. Leur densité de charges moindre que celle de l'or permet de réduire considérablement leurs pertes. La spectroscopie SEIRA utilise des nanoantennes plasmoniques dont les résonances se situent dans l'IR pour couvrir la gamme spectrale des modes vibrationnels moléculaires. L'InAsSb fortement dopé accordé en maille sur un substrat en GaSb présente des propriétés plasmoniques au-delà de 5 µm de longueurs d'onde.Dans ce manuscrit, nous proposons des nanostructures en InAsSb:Si/GaSb pour développer un biocapteur utilisant les techniques de SEIRA et de SPR "sensing". Les nanostructures ont été réalisées soit par photolithographie et gravure chimique humide soit par lithographie interférentielle et gravure par plasma réactif. Les caractérisations optiques ont été effectuées par spectroscopie IR à transformée de Fourier. Des calculs numériques par la méthode des différences finies dans le domaine temporel (FDTD) ont permis d'étudier l'effet des paramètres géométriques sur la réponse optique des structures. Deux types de structure ont été proposés : des réseaux unidimensionnels ainsi que des réseaux bidimensionnels de nanoantennes rectangulaires supportant des résonances de plasmon de surface localisé (LSPR) dans les deux directions de polarisation de la lumière par rapport aux axes de la structure. Ce type de structures permet ainsi une réponse optique ayant des résonances dans deux bandes spectrales différentes. Les techniques de SPR "sensing" et de SEIRA ont été démontrées pour l'ensemble des structures uni- et bidimensionnelles. Différents types d'analytes comme les polymères et le benzaldéhyde vanilline ont servi de systèmes de tests pour les structures plasmoniques. Les sensibilités se situent entre 10² et 10^3 nm/RIU. Les facteurs d'augmentation des signaux vibrationnels obtenus sont compris dans une gamme de 1,2 à 5,7 et les facteurs d'exaltation ont été évalués autour de 10^3 à 10^4 pour les réseaux bidimensionnels de nanoantennes plasmoniques. / The detection and identification of biological and chemical substances can be performed with biosensors. Biosensors are required to be simple and rapid to use, small, and sensitive in order to detect minute amounts of analyte molecules. Plasmonic devices have proven their utility as biosensing transducers. Surface plasmon-polaritons (SPP), collective oscillations of the electron cloud in metallic media coupled to an electromagnetic wave, are sensitive to the refractive index of their environment, providing thus an efficient way to probe the presence of molecules by the refractive index modification. This technique is called surface plasmon resonance (SPR) sensing. Moreover, SPP confine the incident electric field to sub-wavelength dimensions and enhance the field strength. Molecules located in these so-called field hotspots interact more efficiently with incident light due to a coupling mechanism mediated by the SPP, so that their infrared (IR) absorption cross section is increased. While IR spectroscopy is a standard tool for molecular identification, it does not provide sufficient sensitivity for the detection of smallest quantities. Exploiting the surface enhanced IR absorption (SEIRA) due to the plasmonic enhancement enables the detection of small amounts of analyte.While surface plasmons were mainly discovered using noble metals such as gold and silver, nowadays other material systems are also considered which display complementary or improved properties compared to the standard materials in plasmonics, especially to enlarge the spectral range where plasmonic effects can be observed and exploited. Material science enables to tailor the dielectric function of a material and consequently to control the plasmonic properties. Highly doped III-V semiconductors constitute an alternative to gold and silver for mid-IR plasmonics, due to their dielectric function which resembles the one of the noble metals, but shifted to the mid-IR spectral range. Indeed, InAsSb in the IR is even less lossy than gold in the visible. SEIRA using plasmonic resonances spectrally tuned to molecular absorption lines, or resonant SEIRA, requires nanoantenna substrates displaying their resonances in the IR. Highly doped InAsSb grown lattice matched on GaSb substrates is an interesting material system for this task. InAsSb is plasmonic for wavelengths above approximately 5 µm.In this work, we propose InAsSb:Si/GaSb nanostructures as SEIRA and SPR substrates for an application in biosensing devices. InAsSb nanoantennas on GaSb substrates have been prepared using photolithography and wet chemical etching by a citric acid: hydrogen peroxyde solution or alternatively, by interferential lithography and reactive ion etching, especially to reduce the lattice parameter. An optical characterization of the structures was performed by FTIR spectroscopy, supported by numerical finite-difference time-domain (FDTD) calculations which were also applied to study the impact of geometrical parameters on the optical response. Notably, two types of structure designs were proposed: one-dimensional periodic gratings and two-dimensional arrays of rectangular shaped nanoantennas which provide localized surface plasmon resonances (LSPR) in both polarization directions contrary to the gratings and enable hence a dual band optical response. SPR sensing and SEIRA have successfully been demonstrated using both types of structures, with proof-of-concept analytes such as different polymers and the aromatic compound vanillin with absorption features at high IR wavelengths. A bulk sensitivity in the range of 10² to 10^3 nm/RIU was reached. The vibrational signals increased of factors ranging between approximately 1.2-5.7, and the SEIRA enhancement was estimated to be in the range of 10^3 to 10^4 for the rectangular nanoantenna arrays.

Nanoparticle-functionalized electrodes have attracted attention in areas such as energy production and storage, sensing, and electrosynthesis. The electrochemical properties of these electrodes depend upon the nanoparticle properties, e.g., core size, core morphology, surface chemistry, as well as the structure of the nanoparticle/electrode interface, including the coverage on the electrode surface, choice of electrode support, and the interface between the nanoparticle and the electrode support. Traditionally used methods of producing nanoparticle-functionalized electrodes lack sufficient control over many of these variables, particularly the nanoparticle/electrode interface. Tethering nanoparticles to electrodes with molecular linkers is a strategy to fabricate nanoparticle-functionalized electrodes that provides enhanced control over the nanoparticle/electrode structure. However, many existing tethering methods are done on catalytically active electrode supports, which makes isolating the electrochemical activity of the nanoparticle challenging. Furthermore, previous work has focused on larger nanoparticles, yet smaller nanoparticles with core diameters less than 2.5 nm are of interest due to their unique structural and electronic properties. This dissertation addresses both of these gaps, exploring small nanoparticle electrocatalysts that are molecularly tethered to catalytically inert electrodes. This dissertation first reviews and compares the methods of fabricating nanoparticle-functionalized electrodes with a defined molecular interface in the context of relevant attributes for electrochemical applications. Next, a new platform approach to bind small gold nanoparticles to catalytically inert boron doped diamond electrodes through a defined molecular interface is described, and the influence of the nanoparticle/electrode interface on the electron transfer properties of these materials is evaluated. The next two studies build upon this platform to evaluate molecularly tethered nanoparticles as oxygen electroreduction catalysts. The first of these two describes the systematic study of atomically precise small gold clusters, highlighting the influence of atomic level differences in the core size and the electrode support material on the catalytic properties. The second study extends the platform approach to study small bimetallic silver-gold nanoparticles produced on the electrode surface and highlights the influence of the structural arrangement of the metals on the catalytic activity. Finally, future opportunities for the field of molecularly tethered nanoparticle-functionalized electrodes are discussed. This dissertation includes previously published and unpublished co-authored material. / 2019-01-27

Cu(In,Ga)(Se,S)2 (CIGS) solar cells have attracted a lot of attention due to their high performance and the prospect for lower manufacturing costs over conventional crystalline silicon solar cells. All recent record efficiency CIGS absorbers have been deposited using vacuum processing which introduces high manufacturing costs. CIGS can also be compatible with low cost, atmospheric processing which can significantly reduce manufacturing costs. Recently, there has been some progress in developing atmospheric solution-based processes for CIGS. Among different solution approaches, deposition of molecular precursors can be advantageous in terms of simplicity and straightforward compositional control. Nonetheless, the developed methodologies involve highly toxic reagents or large impurity content in the device, limiting the potential for commercialisation. This thesis describes the development of a novel solution-based approach for the deposition of CIGS absorber layers. Metal chalcogenides are used as the starting precursors, which are free from detrimental impurities. These compounds contain strong covalent bonds and, consequently, they are insoluble in common solvents. Until recently, hydrazine, which is highly toxic and explosive, was the only solvent to effectively dissolve these types of precursors, limiting the feasibility of this approach for industrial applications. In this work, metal chalcogenides are dissolved in a safer solvent combination of 1,2-ethanedithiol and 1,2-ethylenediamine, completely eliminating hydrazine from the process. By using this solvent system, optically transparent solutions are formed which exhibit long-term stability. The precursor solutions are decomposed cleanly and they are converted to single phase CIGS upon selenisation. CuIn(S,Se)2 solar cells with power conversion efficiencies up to 8.0% were successfully fabricated by spray depositing the precursor solution, followed by a selenisation step. This progress has been made by continuously optimising the deposition, drying, and especially the selenisation configuration. Among other parameters, the working pressure during selenisation was found to have a dramatic effect on the material crystalline quality. Rapid thermal processing was also explored as an alternative selenisation configuration to tube furnace annealing and it was shown to improve the back contact/absorber interface. It has been demonstrated that Ga can easily be incorporated in the absorber for band-gap tuning and, consequently, for VOC enhancement of the solar cells. The structural properties of the films were investigated with Ga content, as well as the opto-electronic characteristics of the corresponding solar cells. The band-gap of the material was conveniently varied by simply adjusting the precursor ratio, allowing for fine compositional control. By using this technique, Cu(In,Ga)(Se,S)2 solar cells with conversion efficiencies of up to 9.8% were obtained. The solar cell performance in this work is limited by the porosity of the absorber and the back contact quality. Despite a significant improvement during the course of this work, the remaining porosity of the absorber causes selenium to diffuse towards the back forming a thick MoSe2 layer and causing a high series resistance in the device. A low cost, solution-based technique was also developed for the deposition of aluminium-doped zinc oxide films that can be used as the transparent conductive oxide layer in thin film solar cells. This methodology involves the use of an ultrasonic spray pyrolysis system, which is a very versatile and easily controlled deposition technique. Although the presence of oxygen makes the film closer to stoichiometric (fewer oxygen vacancies) good electronic and optical properties have been obtained by process optimisation. Films deposited with optimum conditions exhibited a sheet resistance of 23 Ω/sq, which can be further reduced by increasing the thickness with minimal transmittance losses. The simplicity, low toxicity and straightforward control make the proposed methodologies extremely potential for low cost and scalable deposition of thin film solar cells.

[pt] O uso de amplificadores a fibra dopada, principalmente o amplificador a fibra dopada com érbio (EDFA), permitiram um grande avanço no desenvolvimento das comunicações ópticas e, o uso de ferramentas para caracterizar estes dispositivos é de grande importância. A técnica de reflectometria óptica no domínio da freqüência (OFDR), é bastante eficiente por se tratar de uma técnica não destrutiva e possibilitar a caracterização do ganho através de medidas de ganho distribuído em fibras dopadas. Neste trabalho foi construído um sistema OFDR sintonizável permitindo medidas em diferentes comprimentos de onda, para caracterização de EDFA, operando na banda C (1530-1565 nm) e L (1565-1610 nm), e também fibras dopadas com túlio, operando na banda S (1450-1530 nm). Graças a estas medidas, foram feitos estudos de diversos esquemas de bombeamento e diferentes topologias visando um melhor entendimento e desempenho dos dispositivos, sempre de forma não destrutiva. / [en] The use of doped fiber amplifiers, especially erbium doped- fiber amplifier (EDFA), has been permitted a great advance in optical communications development, and the use of some tools to characterize these devices has a great importance. The optical frequency domain reflectometry technique (OFDR) is very efficient because it is a non-destructive technique and allows the characterization of the gain through distributed gain measurements. In this work a tunable OFDR system was built permitting to perform measurements in different wavelengths, for characterization in EDFA working in C (1530-1565 nm) and L (1565-1610 nm) bands, as well as Thulium doped fibers operating in S (1450-1530 nm) band. Thanks to these measurements, some different pump schemes studies have been made and also different amplifier topologies to find a best device performance, always in a non-destructive way.

>Magister Scientiae - MSc / The main aim of this study is to investigate theelectrochemical determination of two beneficial (selenium and zinc) and two toxic (chromium and vanadium) metals in the potable water within the City of Cape Town's distribution area. The Water Laboratory of the City's Scientific Services Branch analyses for these metals in their elemental state, using the Inductively Coupled Plasma Optical Emission Spectrometer (ICP-OES). This is a standard method used for the detection of trace metals. The most sensitive voltammetric method for determining these metals is by adsorptive stripping voltammetry, using a thin mercury film electrode with a glassy carbon support. This voltammetric method is used for quantitative determination of specific ionic species. Because of mercury's toxicity it is not really favoured for trace metals anymore. Many other possibilities are under investigation, e.g. bismuth-film, modified glassy carbon and antimony electrodes. The boron-doped diamond (BDD) electrode has distinct advantages when used to determine metal concentrations. Advantages of BDD electrodes include lower detection limit, speciation and wider potential window. In this study cyclic voltammetry (CV) was used to determine the copper, cadmium and lead concentrations in potable water by means of square wave voltammetry (SWV) and a bare glassy carbon electrode (GCE). Furthermore, a boron-doped diamond electrode (BDDE) was used to investigate the possibilities of determining selenium, chromium and vanadium by SWV. Real samples (potable water samples) were analysed electrochemically to qualify and quantify these metals and determine whether they comply with the SANS 241:2006 drinking water guidelines.The copper, cadmium, lead and selenium peaks appear very close to the theoretical values, which indicate that these metals can be detected by SWV method, but further analysis with more samples is advised. Even though responses were observed for vanadium and chromium, it was not reliable and requires further investigation. Further studies into the analyses of zinc are also advised.

Este trabalho apresenta o estudo do desempenho de catalisadores nanoestruturados de dióxido de titânio, TiO2, dopados com nitrogênio, visando melhorar sua atividade fotocatalítica sob radiação visível. Os nanotubos de TiO2 foram preparados pelo método hidrotérmico, onde partículas de TiO2 reagem com NaOH a temperatura e pressão elevadas. Em seguida o material é tratado, através de uma lavagem ácida e calcinação, de modo a apresentar as características desejáveis para a aplicação como fotocatalisador. Foram determinadas as melhores condições de obtenção dos nanotubos avaliando-se sua atividade fotocatalítica, variando-se o pH da solução de lavagem e temperatura de calcinação. Determinadas essas condições, buscou-se em três compostos nitrogenados o melhor desempenho para dopagem de nanotubos. Foram eles: amônia, uréia e tiouréia. A reação de degradação do corante rodamina B foi utilizada para avaliar a atividade fotocatalítica dos catalisadores. Os experimentos foram realizados em um reator batelada agitado, com o catalisador em suspensão e na presença de aeração, sob radiação UV e visível. Avaliaram-se inicialmente as condições de reação, como concentração de catalisador e de corante, com o catalisador comercial e precursor de Ti, P25 Degussa. Além da determinação da atividade fotocatalítica, foram feitas as seguintes análises para caracterização dos materiais: difração de raios X (DRX), espectroscopia de refletância difusa (ERD), microscopia eletrônica de transmissão (MET) e determinação da área específica e volume de poros. A partir dos ensaios fotocatalíticos observou-se que os tratamentos a que foram submetidos os materiais tiveram grande influência na sua atividade catalítica. Sob radiação UV nenhum catalisador foi mais ativo que o P 25. Sob radiação visível, as amostras dopadas com tiouréia (NTT-4-500/TiouréiaI) e amônia (NTT-7-600/NH3I) apresentaram os melhores resultados, com um aumento na fotodegradação de 16 e 30 % em relação às amostras não dopadas, respectivamente. / This work presents the study of the catalytic performance of nanostructured titanium oxide, TiO2, doped with nitrogen in order to improve its photocatalytic activity under visible light. TiO2 nanotubes were prepared by hydrothermal method, where TiO2 particles react with NaOH at high temperature and pressure. Then the material was handled through an acid wash and calcination, in order to produce desirable characteristics for the photocatalyst applications. The best conditions for titania nanotubes preparation were determined by varying the pH of the wash water and calcination temperature. Established these conditions, the research focused on obtaining among three nitrogen doping the one that provided best performance of nanotubes. They were: ammonium hydroxide, urea and thiourea. The degradation reaction of rhodamine B dye was used to evaluate the photocatalytic activity of catalyst. The experiments were performed in a stirred batch reactor, with the catalyst in suspension and in the presence of aeration, in the presence of UV and visible radiations. Initially the reaction conditions, such as catalyst and dye concentrations, were determined with the commercial catalyst and Ti precursor, P25 Degussa. In addition to determining the photocatalytic activity, the material characterization was made by X-ray diffraction (XRD), diffusive reflectance spectroscopy (DRS), transmission electron microscopy (TEM) and determination of specific area and pore volume by N2 absorption isotherms. The photocatalytic tests showed that the acid washed and calcination had a strong influence on its photocatalytic activity. No synthesized catalyst presented a larger photodegradation activity under UV light than P25. Under visible light, the samples doped with thiourea (NTT-4-500/TiouréiaI), and ammonia (NTT-7-600/NH3I) showed the best results with an increase in the photodegradation activity of 16 and 30% compared to the undoped samples, respectively.