In nanometer technologies, process variation control and low power have emerged as the first order design goal after high performance. Process variations cause high variability in performance and power consumption of an IC, which affects the overall yield. Short channel effects (SCEs) deteriorate the MOSFET performance and lead to higher leakage power. Double gate devices suppress SCEs and are potential candidates for replacing Bulk technology in nanometer nodes. Threshold voltage control in planar asymmetric double gate transistor (IGFET) using a fourth terminal provides an effective means of combating process variations and low power design. In this thesis, using various case studies, we analyzed the suitability of IGFET for variation control and low power design. We also performed an extensive comparison between IGFET and Bulk for reducing variability, improving yield and leakage power reduction using power gating. We also proposed a new circuit topology for IGFET, which on average shows 33.8 percent lower leakage and 34.9 percent lower area at the cost of 2.8 percent increase in total active mode power, for basic logic gates. Finally, we showed a technique for reducing leakage of minimum sized devices designed using new circuit topology for IGFET.

No description available.

For the past 40 years, relentless focus on Moore’s Law transistor scaling has provided ever-increasing transistor performance and density. In order to continue the technology scaling beyond 22nm node, it is clear that conventional bulk-MOSFET needs to be replaced by new device architectures, most promising being the Multiple-Gate MOSFETs (MuGFET). Intel in mid 2011 announced the use of bulk Tri-Gate FinFETs in 22nm high volume logic process for its next-gen IvyBridge Microprocessor. It is expected that soon other semiconductor companies will also adopt the MuGFET devices. As like bulk-MOSFET, an accurate and physical compact model is important for MuGFET based circuit design. Compact modeling effort for MuGFET started in late nineties with planar double gate MOSFET(DGFET),as it is the simplest structure that one can conceive for MuGFET devices. The models so far proposed for DG MOSFETs are applicable for common gate symmetric DG (SDG) MOSFETs where both the gates have equal oxide thicknesses. However, for practical devices at nanoscale regime, there will always be some amount of asymmetry between the gate oxide thicknesses due to process variations and uncertainties, which can affect device performance significantly. At the same time, Independently controlled DG(IDG) MOSFETs have gained tremendous attention owing to its ability to modulate threshold voltage and transconductance dynamically. Due to the asymmetric nature of the electrostatic, developing efficient compact models for asymmetric/independent DG MOSFET is a daunting task. In this thesis effort has been put to provide some solutions to this challenge. We propose simple surface-potential based compact terminal charge models, applicable for Asymmetric Double gate MOSFETs (ADG) in two configurations1) Common-gate 2) Independent-gate. The charge model proposed for the common-gate ADG (CDG) MOSFET is seamless between the symmetric and asymmetric devices and utilizes the unique so-far-unexplored quasi-linear relationship between the surface potentials along the channel. In this model, the terminal charges could be computed by basic arithmetic operations from the surface potentials and applied biases, and can be easily implemented in any circuit simulator and extendable to short-channel devices. The charge model proposed for independent ADG(IDG)MOSFET is based on a novel piecewise linearization technique of surface potential along the channel. We show that the conventional “charge linearization techniques that have been used over the years in advanced compact models for bulk and double-gate(DG) MOSFETs are accurate only when the channel is fully hyperbolic in nature or the effective gate voltages are same. For other bias conditions, it leads to significant error in terminal charge computation. We demonstrate that the amount of nonlinearity that prevails between the surface potentials along the channel for a particular bias condition actually dictates if the conventional charge linearization technique could be applied or not. We propose a piecewise linearization technique that segments the channel into multiple sections where in each section, the assumption of quasi-linear relationship between the surface potentials remains valid. The cumulative sum of the terminal charges obtained for each of these channel sections yield terminal charges of the IDG device. We next present our work on modeling the non-ideal scenarios like presence of body doping in CDG devices and the non-planar devices like Tri-gate FinFETs. For a fully depleted channel, a simple technique to include body doping term in our charge model for CDG devices, using a perturbation on the effective gate voltage and correction to the coupling factor, is proposed. We present our study on the possibility of mapping a non-planar Tri-gate FinFET onto a planar DG model. In this framework, we demonstrate that, except for the case of large or tall devices, the generic mapping parameters become bias-dependent and an accurate bias-independent model valid for geometries is not possible. An efficient and robust “Root Bracketing Method” based algorithm for computation of surface potential in IDG MOSFET, where the conventional Newton-Raphson based techniques are inefficient due to the presence of singularity and discontinuity in input voltage equations, is presented. In case of small asymmetry for a CDG devices, a simple physics based perturbation technique to compute the surface potential with computational complexity of the same order of an SDG device is presented next. All the models proposed show excellent agreement with numerical and Technology Computer-Aided Design(TCAD) simulations for all wide range of bias conditions and geometries. The models are implemented in a professional circuit simulator through Verilog-A, and simulation examples for different circuits verify good model convergence.

No description available.

I propose compact models of single-gate (SG) and double-gate (DG) JFETs predicting the current-voltage characteristics for both long and short channel devices. In order to make the current equation continuous through all operating conditions from subthreshold to well-above threshold, without non-physical fitting parameters, mobile carriers in depletion region are considered. For describing the short channel behavior, relevant parameters extracted from the two-dimensional analytical solution of Poisson's equation are used for modifying long channel equations. Comparisons of models with the numerical simulation showing close agreement are presented. Based on models, merits of DG JFET over SG JFET and SG MOSFET are discussed by examining the schematic circuit diagram describing the relation between gate and channel potentials for each device. / text

In the context of transistor size miniaturization the motivation of this work was focused on the fabrication process of planar double gate devices. We proposed in this work three process flows based on the use of buried mask which could allow the fabrication of self-aligned planar double gate transistors. The novel concept of buried mask consists into modifying the etch rate of a buried polysilicon or oxide layer. This etch rate modification being defined by ion implantation, etch stop or scacrificial zones aligned with the implantation mask can thus be fabricated. This technique solve the alignment of the front and back gate. Ion implantation causes damages to the implanted target, and is used to dope semiconductor material. If the implanted atoms have a small radii they can induce stress to the implanted lattice. These three consequences of ion implantation, damage, doping and stress are used to modify the etch rate of oxide and polysilicon. High etching selectivity are reached, which allow the fabrication of a localized buried sacrificial or etch stop zone, called buried mask. The definition of the buried mask being done by ion implantation, it opens the possibility to fabricate a buried mask aligned with the implantation mask. Although some more work has to be invested to fabricate planar double gate MOS using buried mask in polysilicon, this concept of buried mask, which could also be called anisotropic wet and vapor etching, is foreseen as a very promising technique in MEMS micromachining and for bio sensor applications.

In this thesis, we carefully investigate the electrical characteristics of junctionless vertical MOSFET (JLVMOS) compared with the junctionless planar MOSFET (JLPMOS) and conversional junction vertical MOSFET (JVMOS). Also, we examine the advantages of the double-gate structure and the short-channel behavior of the junctionless transistors. According to the 2D simulation studies, the proposed JLVMOS can achieve better short-channel characteristics (JLVMOS: 62.04 mV/dec S.S., 23.96 mV/V DIBL; JLPMOS: 77.67 mV/dec S.S., 146.07 mV/V DIBL) as compared with the planar transistor, chiefly owing to the double-gate scheme. This proves that only the double-gate device has better gate controllability over the channel region to reduce the short-channel effect. More importantly is that the JLVMOS has a bulk Si starting material, in which the SOI-induced self-heating effects and the fabrication cost can be well suppressed and reduced, respectively. In comparison with the JVMOS, our proposed JLVMOS exhibits better S.S. and reduced DIBL. Furthermore, although the analog/RF properties of the JLVMOS are somewhat degraded, due to its simple fabrication process, our proposed JLVMOS can become one of the mainstream technology for future CMOS applications.

Esta Tese apresenta os resultados da simulação do transporte eletrônico em três dimensões (3D) no nano dispositivo eletrônico conhecido como “SOI-FinFET”. Este dispositivo é um transistor MOS em tecnologia Silício sobre Isolante – “Silicon-on- Insulator”, SOI – com porta dupla e cujo canal e zonas de fonte e dreno são realizadas em uma estrutura nanométrica vertical de silício chamada de “finger” ou “fin”. Como introdução ao dispositivo em questão, é feita uma revisão básica sobre a tecnologia e transistores SOI e sobre MOSFETs de múltiplas portas. A implementação de um modelo tipo “charge-sheet” para o transistor SOI-MOSFET totalmente depletado e uma modelagem deste dispositivo em altas frequências também é apresentada. A geometria do “fin” é escalada para valores menores do que 100 nm, com uma espessura entre 10 e 20 nm. Um dos objetivos deste trabalho é a definição de parâmetros para o SOI-FinFET que o viabilizem para a tecnologia de 22 nm, com um comprimento efetivo de canal menor do que 20 nm. O transistor FinFET e uma estrutura básica simplificada para simulação numérica em 3D são descritos, sendo utilizados dados de tecnologias atuais de fabricação. São apresentados resultados de simulação numérica 3D (curvas ID-VG, ID-VD, etc.) evidenciando as principais características de funcionamento do FinFET. É analisada a influência da espessura e dopagem do “fin” e do comprimento físico do canal em parâmetros importantes como a tensão de limiar e a inclinação de sublimiar. São consideradas e analisadas duas possibilidades de dopagens da área ativa do “fin”: (1) o caso em que esta pode ser considerada não dopada, sendo baixíssima a probabilidade da presença de dopantes ativos, e (2) o caso de um alto número de dopantes ativos (> 10 é provável). Uma comparação entre dois simuladores numéricos 3D de dispositivos é realizada no intuito de explicitar diferenças entre modelos de simulação e características de descrição de estruturas 3D. São apresentadas e analisadas medidas em dispositivos FinFET experimentais. Dois métodos de extração de resistência série parasita são utilizados em FinFETs simulados e caracterizados experimentalmente. Para finalizar, são resumidas as principais conclusões deste trabalho e são propostos os trabalhos futuros e novas diretivas na pesquisa dos transistores FinFETs. / This thesis presents the results of 3D-numerical simulation of electron transport in double-gate SOI-FinFETs in the decanometer size range. A basic review on the SOI technology and multiple gates MOSFETs is presented. The implementation of a chargesheet model for the fully-depleted SOI-MOSFET and a high frequency modeling of this device are first presented for a planar device topology. The second part of this work deals with FinFETs, a non-planar topology. The geometry of the silicon nano-wire (or “fin”) in this thesis is scaled down well below 100 nm, with fin thickness in the range of 10 to 20 nm. This work addresses the parameters for a viable 22 nm CMOS node, with electrical effective channel lengths below 20 nm. The basic 3D structure of the FinFET transistor is described in detail, then it is simulated with various device structural parameters, and results of 3D-numerical simulation (ID-VG curves, ID-VD, etc.), showing the main features of operation of this device, are presented. The impacts of varying silicon fin thicknesses, physical channel lengths, and silicon fin doping concentration on both the average threshold voltage and the subthreshold slope are investigated. With respect to the doping concentration, the discrete and highly statistical nature of impurity presence in the active area of the nanometer-range fin is considered in two limiting cases: (1) the zero-doping or undoped case, for highly improbable presence of active dopants, and (2) the many-dopants case, or high number (> 10 are probable) of active dopants in the device channel. A comparison between two 3D-numerical device simulators is performed in order to clarify differences between simulation models and features of the description of 3D structures. A structure for SOIFinFETs is optimized, for the undoped fin, showing its applicability for devices with electrical effective channel lengths below 20 nm. SOI-FinFET measurements were performed on experimental devices, analyzed and compared to device simulation results. This thesis uses parasitic resistance extraction methods that are tested in FinFET simulations and measurements. Finally, the main conclusions of this work are summarized and the future work and new directions in the FinFETs research are proposed.

Esta Tese apresenta os resultados da simulação do transporte eletrônico em três dimensões (3D) no nano dispositivo eletrônico conhecido como “SOI-FinFET”. Este dispositivo é um transistor MOS em tecnologia Silício sobre Isolante – “Silicon-on- Insulator”, SOI – com porta dupla e cujo canal e zonas de fonte e dreno são realizadas em uma estrutura nanométrica vertical de silício chamada de “finger” ou “fin”. Como introdução ao dispositivo em questão, é feita uma revisão básica sobre a tecnologia e transistores SOI e sobre MOSFETs de múltiplas portas. A implementação de um modelo tipo “charge-sheet” para o transistor SOI-MOSFET totalmente depletado e uma modelagem deste dispositivo em altas frequências também é apresentada. A geometria do “fin” é escalada para valores menores do que 100 nm, com uma espessura entre 10 e 20 nm. Um dos objetivos deste trabalho é a definição de parâmetros para o SOI-FinFET que o viabilizem para a tecnologia de 22 nm, com um comprimento efetivo de canal menor do que 20 nm. O transistor FinFET e uma estrutura básica simplificada para simulação numérica em 3D são descritos, sendo utilizados dados de tecnologias atuais de fabricação. São apresentados resultados de simulação numérica 3D (curvas ID-VG, ID-VD, etc.) evidenciando as principais características de funcionamento do FinFET. É analisada a influência da espessura e dopagem do “fin” e do comprimento físico do canal em parâmetros importantes como a tensão de limiar e a inclinação de sublimiar. São consideradas e analisadas duas possibilidades de dopagens da área ativa do “fin”: (1) o caso em que esta pode ser considerada não dopada, sendo baixíssima a probabilidade da presença de dopantes ativos, e (2) o caso de um alto número de dopantes ativos (> 10 é provável). Uma comparação entre dois simuladores numéricos 3D de dispositivos é realizada no intuito de explicitar diferenças entre modelos de simulação e características de descrição de estruturas 3D. São apresentadas e analisadas medidas em dispositivos FinFET experimentais. Dois métodos de extração de resistência série parasita são utilizados em FinFETs simulados e caracterizados experimentalmente. Para finalizar, são resumidas as principais conclusões deste trabalho e são propostos os trabalhos futuros e novas diretivas na pesquisa dos transistores FinFETs. / This thesis presents the results of 3D-numerical simulation of electron transport in double-gate SOI-FinFETs in the decanometer size range. A basic review on the SOI technology and multiple gates MOSFETs is presented. The implementation of a chargesheet model for the fully-depleted SOI-MOSFET and a high frequency modeling of this device are first presented for a planar device topology. The second part of this work deals with FinFETs, a non-planar topology. The geometry of the silicon nano-wire (or “fin”) in this thesis is scaled down well below 100 nm, with fin thickness in the range of 10 to 20 nm. This work addresses the parameters for a viable 22 nm CMOS node, with electrical effective channel lengths below 20 nm. The basic 3D structure of the FinFET transistor is described in detail, then it is simulated with various device structural parameters, and results of 3D-numerical simulation (ID-VG curves, ID-VD, etc.), showing the main features of operation of this device, are presented. The impacts of varying silicon fin thicknesses, physical channel lengths, and silicon fin doping concentration on both the average threshold voltage and the subthreshold slope are investigated. With respect to the doping concentration, the discrete and highly statistical nature of impurity presence in the active area of the nanometer-range fin is considered in two limiting cases: (1) the zero-doping or undoped case, for highly improbable presence of active dopants, and (2) the many-dopants case, or high number (> 10 are probable) of active dopants in the device channel. A comparison between two 3D-numerical device simulators is performed in order to clarify differences between simulation models and features of the description of 3D structures. A structure for SOIFinFETs is optimized, for the undoped fin, showing its applicability for devices with electrical effective channel lengths below 20 nm. SOI-FinFET measurements were performed on experimental devices, analyzed and compared to device simulation results. This thesis uses parasitic resistance extraction methods that are tested in FinFET simulations and measurements. Finally, the main conclusions of this work are summarized and the future work and new directions in the FinFETs research are proposed.

Esta Tese apresenta os resultados da simulação do transporte eletrônico em três dimensões (3D) no nano dispositivo eletrônico conhecido como “SOI-FinFET”. Este dispositivo é um transistor MOS em tecnologia Silício sobre Isolante – “Silicon-on- Insulator”, SOI – com porta dupla e cujo canal e zonas de fonte e dreno são realizadas em uma estrutura nanométrica vertical de silício chamada de “finger” ou “fin”. Como introdução ao dispositivo em questão, é feita uma revisão básica sobre a tecnologia e transistores SOI e sobre MOSFETs de múltiplas portas. A implementação de um modelo tipo “charge-sheet” para o transistor SOI-MOSFET totalmente depletado e uma modelagem deste dispositivo em altas frequências também é apresentada. A geometria do “fin” é escalada para valores menores do que 100 nm, com uma espessura entre 10 e 20 nm. Um dos objetivos deste trabalho é a definição de parâmetros para o SOI-FinFET que o viabilizem para a tecnologia de 22 nm, com um comprimento efetivo de canal menor do que 20 nm. O transistor FinFET e uma estrutura básica simplificada para simulação numérica em 3D são descritos, sendo utilizados dados de tecnologias atuais de fabricação. São apresentados resultados de simulação numérica 3D (curvas ID-VG, ID-VD, etc.) evidenciando as principais características de funcionamento do FinFET. É analisada a influência da espessura e dopagem do “fin” e do comprimento físico do canal em parâmetros importantes como a tensão de limiar e a inclinação de sublimiar. São consideradas e analisadas duas possibilidades de dopagens da área ativa do “fin”: (1) o caso em que esta pode ser considerada não dopada, sendo baixíssima a probabilidade da presença de dopantes ativos, e (2) o caso de um alto número de dopantes ativos (> 10 é provável). Uma comparação entre dois simuladores numéricos 3D de dispositivos é realizada no intuito de explicitar diferenças entre modelos de simulação e características de descrição de estruturas 3D. São apresentadas e analisadas medidas em dispositivos FinFET experimentais. Dois métodos de extração de resistência série parasita são utilizados em FinFETs simulados e caracterizados experimentalmente. Para finalizar, são resumidas as principais conclusões deste trabalho e são propostos os trabalhos futuros e novas diretivas na pesquisa dos transistores FinFETs. / This thesis presents the results of 3D-numerical simulation of electron transport in double-gate SOI-FinFETs in the decanometer size range. A basic review on the SOI technology and multiple gates MOSFETs is presented. The implementation of a chargesheet model for the fully-depleted SOI-MOSFET and a high frequency modeling of this device are first presented for a planar device topology. The second part of this work deals with FinFETs, a non-planar topology. The geometry of the silicon nano-wire (or “fin”) in this thesis is scaled down well below 100 nm, with fin thickness in the range of 10 to 20 nm. This work addresses the parameters for a viable 22 nm CMOS node, with electrical effective channel lengths below 20 nm. The basic 3D structure of the FinFET transistor is described in detail, then it is simulated with various device structural parameters, and results of 3D-numerical simulation (ID-VG curves, ID-VD, etc.), showing the main features of operation of this device, are presented. The impacts of varying silicon fin thicknesses, physical channel lengths, and silicon fin doping concentration on both the average threshold voltage and the subthreshold slope are investigated. With respect to the doping concentration, the discrete and highly statistical nature of impurity presence in the active area of the nanometer-range fin is considered in two limiting cases: (1) the zero-doping or undoped case, for highly improbable presence of active dopants, and (2) the many-dopants case, or high number (> 10 are probable) of active dopants in the device channel. A comparison between two 3D-numerical device simulators is performed in order to clarify differences between simulation models and features of the description of 3D structures. A structure for SOIFinFETs is optimized, for the undoped fin, showing its applicability for devices with electrical effective channel lengths below 20 nm. SOI-FinFET measurements were performed on experimental devices, analyzed and compared to device simulation results. This thesis uses parasitic resistance extraction methods that are tested in FinFET simulations and measurements. Finally, the main conclusions of this work are summarized and the future work and new directions in the FinFETs research are proposed.