Despite the many attractive features of carbon fiber reinforced polymers (FRPs) composites, they are prone to failure due to delamination. The ability to tailor the fiber/matrix interface FRPs is crucial to the development of composite materials with enhanced structural performance. In this dissertation, ZnO nanowires (NWs) were grown on the surface of carbon fibers utilizing low temperature hydrothermal synthesis technique prior to the hybrid composite fabrication. The scanning electron microscopy revealed that the ZnO nanowires were grown uniformly on the surface of the carbon fabric. The surface grown ZnO NWs functionally-graded the composite material properties and ensured effective load transfer across the interface. To assess the influence of the ZnO NWs growth, reference samples were also prepared by exposing the carbon fabric to the hydrothermal conditions. The damping properties of the hybrid ZnO NWs-CFRP composite were examined using the dynamic mechanical analysis (DMA) technique. The results showed enhanced energy dissipation within the hybrid composite. Quasi-static tensile testing revealed that the in-plane and out-of-plane strengths and moduli of the hybrid FRP composite were also boosted. The interlaminar shear strength (ILSS) measurements suggested the improvement in the mechanical properties of the composite to the enhanced adhesion between the ZnO nanowires and the other constituents (carbon fiber and epoxy). It was necessary thus, to utilize the molecular dynamics simulations (MD) to investigate the adhesion within the CFRP structure upon growing the ZnO nanowires on the surface of the carbon fibers. Molecular models of the carbon fibers, the epoxy matrix and the ZnO nanowires were built. The resulting molecular structures were minimized and placed within a simulation box with periodic boundary conditions. The MD simulations were performed using the force field COMPASS to account for the empirical energy interactions between the different toms in the simulation box. Proper statistical thermodynamics were employed to relate the dynamics of the molecular model to the macroscale thermodynamic states (pressure, temperature and volume). Per the computed potential energies of the different components of the composite, it was found that the polar surfaces in the ZnO structures facilitates good adhesion properties in the graphite-epoxy composite. Besides the attractive mechanical properties of the ZnO nanowires, their piezoelectric and semiconductor properties were sought to design an energy harvesting device. To ensure sufficient charges collection from the mechanically stressed individual ZnO nanowires, a copper layer was sputtered on top of the ZnO nanowires which introduced also a Schottky effect. The mechanical excitation was provided by exposing the device to different vibration environment. The output voltage and currents were measured at the conditions (in terms of frequency and resistive load). It was demonstrated that the electrical output could be enhanced by stacking up similar devices in series or in parallel. Finally, in an attempt to exploit the reversibility of the electromechanical coupling of the energy harvesting device, the constitutive properties of the hybrid ZnO nanowires-CFRP composite were estimated using the Mori-Tanaka approach. This approach was validated by a finite element model (FEM). The FEM simulations were performed on a representative volume element (RVE) to reduce the computational time. The results demonstrated that the mechanical properties of the hybrid ZnO NWs-CFRP composite were better than those for the baseline CFRP composite with identical carbon fiber volume fraction (but with no ZnO NWs) which confirmed the experimental findings. Furthermore, the electro-elastic properties of the hybrid composite were determined by applying proper boundary conditions to the FE RVE. The work outlined in this dissertation will enable significant advancement in the next generation of hybrid composites with improved structural and energy harvesting multifunctionalties. / Ph. D.

When bonded joints are subjected to harsh environmental conditions, the interphase, the three-dimensional region surrounding the adhesive/substrate interface, becomes critically important. Frequently, failure occurs in this region after adhesively bonded systems are subjected to elevated temperature oxidative aging. In a previous study, this was found to be the case with a polyimide adhesive bonded to chromic acid anodized (CAA) Ti-6Al-4V. The objective of the current research has been twofold: 1) to investigate the effect of thermal aging on the interphase region of polyimide/titanium adhesive joints, and 2) to evaluate the method used in the current study for durability characterization of other adhesive/substrate systems. The method used in this research has been to characterize the effect of elevated temperature aging on the following systems: 1) Notched coating adhesion (NCA) specimens and 2) bulk samples of dispersed substrate particles in an adhesive matrix. The NCA test has the advantages of an accelerated aging geometry and a mode mix that leads to failure through the interphase, the region of interest. The bulk samples have the advantage of an increased interphase volume and allow for the application of bulk analysis techniques to the interphase, a region that is traditionally limited to surface analysis techniques. The adhesive systems studied consisted of one of two polyimide adhesives, LaRC© PETI-5 or Cytec Fiberite© FM-5, bonded to CAA Ti-6Al-4V. The model filled system consisted of a PETI-5 matrix with amorphous titanium dioxide filler. Through the use of the NCA test, it was determined that bonded specimens made with FM-5 lose approximately 50% of their original fracture energy when aged in air at 177°C for 30 days. This aging temperature is well below the glass transition temperature of the adhesive, 250°C. At the same time, the failure location moves from the anodized oxide layer to the adhesive that is directly adjacent to the substrate surface, the interphase region. Through surface analysis of this region, it is determined that the adhesive penetrates the pores of the CAA surface to a depth of 70 to 100 nm, promoting adhesion at the interface. With aging, the adhesive in the interphase region appears to be weakening, although analysis of the bulk adhesive after aging shows little change. This indicates that adhesive degradation is enhanced in the interphase compared to the bulk. Analysis of the model filled system gave similar information. Specimens containing titanium dioxide filler had glass transition temperatures that were approximately 20°C lower than the neat polyimide samples. In addition, the filled samples contained a significant portion of low molecular weight extractable material that was not present in the neat specimens. The tan delta spectra from dynamic mechanical thermal analysis of the filled specimens exhibited a shoulder on the high-temperature side of the glass transition peak. This shoulder is attributed to the glass transition of the interphase, a distinct phase of the polyimide which is constrained by adsorption onto the filler particle surfaces. As a function of aging time at 177° or 204°C, the shoulder decreases substantially in magnitude, which may relate to loss of adhesive strength between the polyimide and the filler particles. From this research, it has been illustrated that information relating to the durability of adhesively bonded systems is gained using an interfacially debonding adhesive test and a model system of substrate particles dispersed in an adhesive matrix / Ph. D.

This thesis examines the dynamic mechanical properties of natural silk fibres, mainly from silkworm species Bombyx mori (B. mori) and spider species Nephila edulis, using dynamic mechanical thermal analysis, DMTA. The aim is not only to provide novel data on mechanical properties of silk, but also to relate these properties to the structure and morphology of silk. A systematic approach is adopted to evaluate the effect of the three principal factors of stress, temperature and hydration on the properties and structure of silk. The methods developed in this work are then used to examine commercially important aspects of the ‘quality’ of silk. I show that the dynamic storage modulus of silks increases with loading stress in the deformation through yield to failure, whereas the conventional engineering tensile modulus decreases significantly post-yield. Analyses of the effects of temperature and thermal history show a number of important effects: (1) the loss peak at -60 °C is found to be associated the protein-water glass transition; (2) the increase in the dynamic storage modulus of native silks between temperature +25 and 100 °C is due simply to water loss; (3) a number of discrete loss peaks from +150 to +220°C are observed and attributed to the glass transition of different states of disordered structure with different intermolecular hydrogen bonding. Excess environmental humidity results in a lower effective glass transition temperature (Tg) for disordered silk fractions. Also, humidity-dynamic mechanical analysis on Nephila edulis spider dragline silks has shown that the glass transition induces a partial supercontraction, called Tg contraction. This new finding leads to the conclusion of two independent mechanisms for supercontraction in spider dragline silks. Study of three commercial B. mori cocoon silk grades and a variety of processed silks or artificial silks shows that lower grade and poorly processed silks display lower Tg values, and often have a greater loss tangent at Tg due to increased disorder. This suggests that processing contributes significantly to the differences in the structural order among natural or unnatural silks. More importantly, dynamic mechanical thermal analysis is proposed to be a potential tool for quality evaluation and control in silk production and processing. In summary, I demonstrate that DMTA is a valuable analytical tool for understanding the structure and properties of silk, and use a systematic approach to understand quantitatively the important mechanical properties of silk in terms of a generic structural framework in silk proteins.

This thesis, conducted in collaboration with IKEA Components, explores the rate-temperature dependence of polyoxymethylene (POM) thermoplastic using dynamic mechanical thermal analysis (DMTA). A force-controlled DMTA study was carried out, and the experimental data were processed to derive the complex, storage, and loss modulus. Master curves were constructed using the time-temperature superposition (TTS) method, comparing the Arrhenius and William-Landel-Ferry (WLF) equations. Additionally, a master curve was manually created by shifting isothermal material properties. This manual curve was then compared to those generated using standard equations. The study found that the storage modulus was the dominant phenomenon in POM, with the loss modulus showing distortion likely due to measurement noise. Results indicated a slight softening of the storage modulus with increased cyclic loading. The manually constructed master curve was more coherent compared to those derived from the Arrhenius and WLF equations.