No presente trabalho, o desempenho elétrico dos eletrocatalisadores anódicos Pt/C, Pt3Sn/C(liga), Pt(SnO2)/C, Pt3(SnO2)/C e Pt9(SnO2)/C para as reações de eletro-oxidação de etanol, acetaldeído e ácido acético foi investigado. Testes em célula unitária mostraram que a adição de Sn seja na forma de liga Pt-Sn ou na forma de óxido (SnO2) coexistente com a platina metálica aumenta consideravelmente a resposta elétrica gerada pela célula. A melhora no desempenho elétrico dos catalisadores a base de PtSn é resultado da capacidade em oxidar o acetaldeído, majoritariamente produzido pelo Pt/C, em ácido acético. Pt3(SnO2)/C exibiu a melhor resposta elétrica tanto para o etanol quanto para acetaldeído como combustíveis, alcançando valores de densidade de potência máxima de 127 e 58 mW cm-2, respectivamente. Misturas entre os combustíveis mostraram que o acetaldeído é um composto que leva a uma rápida desativação dos catalisadores, enquanto que o ácido acético, embora não seja oxidado a CO2 nas condições de operação, não afeta o desempenho elétrico da célula. / In the present work, the electrical performance of the anodic electrocatalysts Pt/C, Pt3Sn/C(alloy), Pt(SnO2)/C, Pt3(SnO2)/C and Pt9(SnO2)/C towards ethanol, acetaldehyde and acetic acid electro-oxidation reactions was investigated. Single cell tests showed that the Sn addiction whether in Pt-Sn alloyed form or in oxide (SnO2) form coexisting with metallic platinum increases considerably the electrical response generated by the cell. The electrical performance improvement of PtSn-basis catalysts is a result of the ability to oxidize acetaldehyde, mostly produced by Pt/C, in acetic acid. Pt3(SnO2)/C exhibited the highest electrical performance both for ethanol and acetaldehyde as fuels, reaching maximum power density values of 127 and 58 mW cm-2, respectively. Mixtures between fuels showed that acetaldehyde is a compound which leads a rapid deactivation of the catalysts, while acetic acid, although not oxidized to CO2 under operating conditions, does not affect the cell electrical performance.

Os eletrocatalisadores quartenários PtSnAuRh/C e PtRuAuRh/C foram preparados nas proporções 50:40:5:5, 60:30:5:5, 70:20:5:5, 80:10:5:5, 90:4:3:3 e para as composições terciárias PtSnAu/C, PtSnRh/C, PtRuAu/C, PtRuRh/C preparados na proporção atômica 50:45:5 com (20% em massa) pelo método da redução por álcool utilizando H2PtCl6.6H2O, RuCl3·xH2O, SnCl2.2H2O, HAuCl4.3H2O e RhCl3.xH2O, como fonte de metais e carbono Vulcan XC72 como suporte e, por último, etileno glicol como agente redutor. Os eletrocatalisadores obtidos foram caracterizados fisicamente por difração de raios-X (DRX), energia dispersiva de raios X (EDX) e microscopia eletrônica de transmissão (MET). As análises por EDX mostraram que as razões atômicas dos diferentes eletrocatalisadores, preparados pelo método da redução por álcool, foram similares às composições nominais de partida indicando que esta metodologia é eficiente para a preparação destes eletrocatalisadores. Em todos os difratogramas para os eletrocatalisadores preparados observa-se um pico largo em aproximadamente 2θ = 25°, o qual é associado ao suporte de carbono e quatro outros picos de difração em aproximadamente 2θ = 40°, 47°, 67° e 82°, que por sua vez são associados aos planos (111), (200), (220) e (311), respectivamente, da estrutura cúbica de face centrada (CFC) de platina. Os resultados de difração de raios X apresentaram tamanhos médios de cristalitos entre 2,0 e 5,2 nm para PtSnAuRh/C, PtSnAu/C, PtSnRh/C e 2,0 a 2,6 nm para PtRuAuRh/C, PtRuAu/C, PtRuRh/C. Os estudos para a oxidação eletroquímica do etanol em meio ácido foram realizados utilizando as técnicas de voltametria cíclica e de cronoamperometria em uma solução 0,5 mol.L-1 H2SO4, + 1,0 mol.L-1 de C2H5OH. As curvas de polarização obtidas na célula a combustível unitária, alimentada diretamente por etanol, estão de acordo com os resultados de voltametria e cronoamperometria constatando o efeito benéfico da adição do ouro e ródio na composição dos eletrocatalisadores. / The electrocatalysts quaternary PtSnAuRh/C and PtRuAuRh/C were prepared in the proportions 50:40:5:5, 60:30:5:5, 70:20:5:5, 80:10:5:5, 90:4:3:3 and for compositions PtSnAu/C, PtSnRh/C, PtRuAu/C, PtRuRh/C prepared in atomic ratio 50: 45: 5 with (20 mass%) by the method of alcohol reduction using H2PtCl6.6H2O, RuCl3·xH2O, SnCl2.2H2O, HAuCl4.3H2O and RhCl3.xH2O as a source of carbon and Vulcan XC72 as support and, lastly, ethylene glycol as a reducing agent. The obtained electrocatalysts were physically characterized by X-ray diffraction (XRD), energy dispersive X-ray (EDX) and transmission electron microscopy (TEM). The EDX analyzes showed that the atomic ratios of the various electrocatalysts prepared by the method of alcohol reduction were similar to the nominal compositions of departure indicating that this method is efficient for preparing these electrocatalysts. In all diffraction patterns for the prepared electrocatalysts observed a broad peak at about 2θ = 25, which is associated with the carbon and four other diffraction peaks support at about 2θ = 40, 47, 67 and 82, which in turn they are associated with the planes (111), (200), (220) and (311) respectively of the face-centered cubic structure (FCC) of platinum. The results of X-ray diffraction showed average crystallite size between 2.0 and 5.2 nm for PtSnAuRh/C, PtSnAu/C, PtSnRh/C and 2.0 to 2.6 nm for PtRuAuRh/C, PtRuAu/C , PtRuRh/C. The studies for the electrochemical oxidation of ethanol in acidic medium were performed using cyclic voltammetry and chronoamperometry in a 0.5 mol L-1 solution H2SO4 + 1.0 mol L-1 C2H5OH. The polarization curves obtained on the unit fuel cell, fed directly with ethanol, are in agreement with the results of voltammetry and chronoamperometry stating the beneficial effect of adding gold and rhodium in the composition of the electrocatalysts.

No presente trabalho, o desempenho elétrico dos eletrocatalisadores anódicos Pt/C, Pt3Sn/C(liga), Pt(SnO2)/C, Pt3(SnO2)/C e Pt9(SnO2)/C para as reações de eletro-oxidação de etanol, acetaldeído e ácido acético foi investigado. Testes em célula unitária mostraram que a adição de Sn seja na forma de liga Pt-Sn ou na forma de óxido (SnO2) coexistente com a platina metálica aumenta consideravelmente a resposta elétrica gerada pela célula. A melhora no desempenho elétrico dos catalisadores a base de PtSn é resultado da capacidade em oxidar o acetaldeído, majoritariamente produzido pelo Pt/C, em ácido acético. Pt3(SnO2)/C exibiu a melhor resposta elétrica tanto para o etanol quanto para acetaldeído como combustíveis, alcançando valores de densidade de potência máxima de 127 e 58 mW cm-2, respectivamente. Misturas entre os combustíveis mostraram que o acetaldeído é um composto que leva a uma rápida desativação dos catalisadores, enquanto que o ácido acético, embora não seja oxidado a CO2 nas condições de operação, não afeta o desempenho elétrico da célula. / In the present work, the electrical performance of the anodic electrocatalysts Pt/C, Pt3Sn/C(alloy), Pt(SnO2)/C, Pt3(SnO2)/C and Pt9(SnO2)/C towards ethanol, acetaldehyde and acetic acid electro-oxidation reactions was investigated. Single cell tests showed that the Sn addiction whether in Pt-Sn alloyed form or in oxide (SnO2) form coexisting with metallic platinum increases considerably the electrical response generated by the cell. The electrical performance improvement of PtSn-basis catalysts is a result of the ability to oxidize acetaldehyde, mostly produced by Pt/C, in acetic acid. Pt3(SnO2)/C exhibited the highest electrical performance both for ethanol and acetaldehyde as fuels, reaching maximum power density values of 127 and 58 mW cm-2, respectively. Mixtures between fuels showed that acetaldehyde is a compound which leads a rapid deactivation of the catalysts, while acetic acid, although not oxidized to CO2 under operating conditions, does not affect the cell electrical performance.

Os eletrocatalisadores quartenários PtSnAuRh/C e PtRuAuRh/C foram preparados nas proporções 50:40:5:5, 60:30:5:5, 70:20:5:5, 80:10:5:5, 90:4:3:3 e para as composições terciárias PtSnAu/C, PtSnRh/C, PtRuAu/C, PtRuRh/C preparados na proporção atômica 50:45:5 com (20% em massa) pelo método da redução por álcool utilizando H2PtCl6.6H2O, RuCl3·xH2O, SnCl2.2H2O, HAuCl4.3H2O e RhCl3.xH2O, como fonte de metais e carbono Vulcan XC72 como suporte e, por último, etileno glicol como agente redutor. Os eletrocatalisadores obtidos foram caracterizados fisicamente por difração de raios-X (DRX), energia dispersiva de raios X (EDX) e microscopia eletrônica de transmissão (MET). As análises por EDX mostraram que as razões atômicas dos diferentes eletrocatalisadores, preparados pelo método da redução por álcool, foram similares às composições nominais de partida indicando que esta metodologia é eficiente para a preparação destes eletrocatalisadores. Em todos os difratogramas para os eletrocatalisadores preparados observa-se um pico largo em aproximadamente 2θ = 25°, o qual é associado ao suporte de carbono e quatro outros picos de difração em aproximadamente 2θ = 40°, 47°, 67° e 82°, que por sua vez são associados aos planos (111), (200), (220) e (311), respectivamente, da estrutura cúbica de face centrada (CFC) de platina. Os resultados de difração de raios X apresentaram tamanhos médios de cristalitos entre 2,0 e 5,2 nm para PtSnAuRh/C, PtSnAu/C, PtSnRh/C e 2,0 a 2,6 nm para PtRuAuRh/C, PtRuAu/C, PtRuRh/C. Os estudos para a oxidação eletroquímica do etanol em meio ácido foram realizados utilizando as técnicas de voltametria cíclica e de cronoamperometria em uma solução 0,5 mol.L-1 H2SO4, + 1,0 mol.L-1 de C2H5OH. As curvas de polarização obtidas na célula a combustível unitária, alimentada diretamente por etanol, estão de acordo com os resultados de voltametria e cronoamperometria constatando o efeito benéfico da adição do ouro e ródio na composição dos eletrocatalisadores. / The electrocatalysts quaternary PtSnAuRh/C and PtRuAuRh/C were prepared in the proportions 50:40:5:5, 60:30:5:5, 70:20:5:5, 80:10:5:5, 90:4:3:3 and for compositions PtSnAu/C, PtSnRh/C, PtRuAu/C, PtRuRh/C prepared in atomic ratio 50: 45: 5 with (20 mass%) by the method of alcohol reduction using H2PtCl6.6H2O, RuCl3·xH2O, SnCl2.2H2O, HAuCl4.3H2O and RhCl3.xH2O as a source of carbon and Vulcan XC72 as support and, lastly, ethylene glycol as a reducing agent. The obtained electrocatalysts were physically characterized by X-ray diffraction (XRD), energy dispersive X-ray (EDX) and transmission electron microscopy (TEM). The EDX analyzes showed that the atomic ratios of the various electrocatalysts prepared by the method of alcohol reduction were similar to the nominal compositions of departure indicating that this method is efficient for preparing these electrocatalysts. In all diffraction patterns for the prepared electrocatalysts observed a broad peak at about 2θ = 25, which is associated with the carbon and four other diffraction peaks support at about 2θ = 40, 47, 67 and 82, which in turn they are associated with the planes (111), (200), (220) and (311) respectively of the face-centered cubic structure (FCC) of platinum. The results of X-ray diffraction showed average crystallite size between 2.0 and 5.2 nm for PtSnAuRh/C, PtSnAu/C, PtSnRh/C and 2.0 to 2.6 nm for PtRuAuRh/C, PtRuAu/C , PtRuRh/C. The studies for the electrochemical oxidation of ethanol in acidic medium were performed using cyclic voltammetry and chronoamperometry in a 0.5 mol L-1 solution H2SO4 + 1.0 mol L-1 C2H5OH. The polarization curves obtained on the unit fuel cell, fed directly with ethanol, are in agreement with the results of voltammetry and chronoamperometry stating the beneficial effect of adding gold and rhodium in the composition of the electrocatalysts.

In this study SBA-15 mesoporous silica template was synthesized and used as a sacrificial template in the preparation of ordered mesoporous carbon material. A chemical vapour deposition (CVD) technique using LPG or alternatively sucrose, pyrolyzed upon a mesoporous Si matrix were used to produce nanostructured ordered mesoporous carbon (OMC) with graphitic character after removing the Si template. The sucrose method was found to be a suitable route for preparing OMC. The OMC was used as a conductive three dimensional porous support for depositing catalytic nanophase Pt metal. Deposition of Pt nanoparticles on OMC was accomplished using a CVD method with Pt(acac)2 as a precursor. The synthesized nano-composite materials were characterized by several techniques such as, HRTEM, HRSEM, EDS, XRD, BET, TGA, FT-IR and CV.

Direct methanol fuel cells (DMFC) are being investigated as a portable energy conversion device for military and commercial applications. DMFCs offer the potential to efficiently extract electricity from a dense liquid fuel. However, improvements in materials properties and lowering the cost of the electrocatalysts used in a DMFC are necessary for commercialization of the technology. The cathode electrocatalyst is a critical issue in DMFC because the state-of-the-art catalyst, platinum, is very expensive and rare, and its performance is diminished by methanol that crosses over from the anode to the cathode through the Nafion membrane. This thesis investigates the addition of platinum to a palladium-cobalt nanoalloy electrocatalyst supported on carbon black in order to improve catalyst activity for the oxygen reduction reaction (ORR) and catalyst stability against dissolution in acidic environment without significantly reducing the methanol-tolerance of the catalyst. Platinum was added to the palladium-cobalt nanoalloy catalyst using two synthesis methods. In the first method, platinum was directly alloyed with palladium and cobalt using a polyol reduction method, followed by heat treatment in a reducing atmosphere to form catalysts with 11 and 22 atom % platinum. In the second method, platinum was added to a palladium-cobalt alloy by galvanic displacement reaction to form catalysts with 10 and 22 atom % platinum. The palladium cobalt alloy was synthesized using a polyol method, followed by heat treatment in a reducing atmosphere to alloy the nanoparticles before the Pt displacement. It was found that both methods significantly improve catalyst activity and stability, with the displaced catalysts showing a higher activity than the corresponding alloy catalyst. However the alloy catalysts showed similar resistance to dissolution as the displaced catalysts, and the alloyed catalysts were more tolerant to methanol. The displaced catalyst with 22 atom % platinum (8 wt. % Pt overall) performed similar to a 20 wt. % commercial platinum catalyst in both RDE and single cell DMFC tests. The 10 and 22 atom % Pt displaced catalysts and 22 atom % Pt alloyed all showed higher Pt mass specific activities than a commercial Pt catalyst. / text

Η ανάπτυξη νέων τεχνολογιών ανανεώσιμων πηγών ενέργειας τα τελευταία χρόνια, έχει γίνει αναγκαία με τη συνεχόμενη περιβαλλοντική ρύπανση και την αλόγιστη σπατάλη των φυσικών πόρων. Οι τεχνολογίες υδρογόνου και ειδικά η παραγωγή υδρογόνου μέσω της διαδικασίας της ηλεκτρόλυσης έχει αρχίσει να κερδίζει σημαντικό έδαφος τα τελευταία χρόνια με τη συνεχιζόμενη ανακάλυψη νέων υλικών, αποδοτικών και με χαμηλό κόστος. Στην παρούσα εργασία θα αναλύσουμε την τεχνολογία παραγωγής υδρογόνου με ηλεκτρόλυση καθώς και την παρασκευή υλικών με τη μέθοδο της ηλεκτροχημικής εναπόθεσης διμεταλλικών και τριμεταλλικών λεπτών υμενίων μεταβατικών μετάλλων με βάση το Νικέλιο (Ni). Τα κράματα Νικελίου με προσθήκη άλλων μετάλλων όπως Fe, Co, Mo κ.α. έχουν τεράστιο ερευνητικό ενδιαφέρον λόγω των πολύ καλών ηλεκτροκαταλυτικών ιδιοτήτων που παρουσιάζουν όσον αφορά την παραγωγή υδρογόνου, καθώς παρουσιάζουν καλύτερες ιδιότητες και από την Πλατίνα(Pt), που αποτελεί το αποδοτικότερο αλλά και το ακριβότερο μέταλλο που έχει χρησιμοποιηθεί ως καταλύτης για παραγωγή υδρογόνου. Η τεχνολογία της ηλεκτροχημικής εναπόθεσης λεπτών υμενίων προσφέρει υλικά πορώδη, αποδοτικά, φθηνά και ανθεκτικά σε συνθήκες έντονο αλκαλικού και όξινου περιβάλλοντος. Τα υλικά που παρασκευάσαμε ήταν NiFe, NiFeZn, NiCoZn, NiCoFeZn και NiMoZn. Κύριος στόχος της εργασίας αυτής ήταν η μελέτη των συνθηκών της ηλεκτροχημικής εναπόθεσης και ο τρόπος με τον οποίο επηρεάζουν τη μορφολογία και τις ιδιότητες των λεπτών υμενίων. Αρχικά μελετήσαμε τα υμένια σε πραγματικές συνθήκες ηλεκτρόλυσης, μετρώντας την παραγωγή υδρογόνου για συγκεκριμένες πάντα συνθήκες. Στη συνέχεια έγιναν μετρήσεις υπερδυναμικού παραγωγής υδρογόνου και από τα δεδομένα αυτά και με τη βοήθεια των διαγραμμάτων Tafel υπολογίσαμε ηλεκτροκαταλυτικούς συντελεστές όπως η πυκνότητα ρεύματος ανταλλαγής και η κλίση Tafel. Τέλος μετρήσεις σε ηλεκτρονικό μικροσκόπιο σάρωσης (SEM) και στοιχειακές αναλύσεις (EDX) μας έδωσαν μια πιο ολοκληρωμένη εικόνα για την επίδραση των συνθηκών της ηλεκτροχημικής εναπόθεσης στην μορφολογία της επιφάνειας των λεπτών υμενίων και των ιδιοτήτων τους. Μελετήσαμε τις ηλεκτροκαταλυτικές ιδιότητες ενός νέου υλικού (NiCoFeZn), καταλήγοντας στο συμπέρασμα ότι είναι ένα πολλά υποσχόμενο υλικό για την παραγωγή υδρογόνου και για το λόγο αυτό πρέπει να μελετηθεί εκτενέστερα, καθώς σήμερα χρησιμοποιείται κυρίως ως μαγνητικό υλικό. / The continuous environmental pollution and the depletion of natural resources have brought forward the need for the development of new renewable energy technologies. Hydrogen technologies and especially electrolytic hydrogen production, has gained considerable ground in the recent years due to the discovery of new, efficient and low cost alloy compounds. In this work we analyze the electrolytic hydrogen production and the fabrication of electrodeposited binary and ternary Nickel-based thin film alloys. The addition of the Fe, Co, Mo transition metals in Nickel-based alloys is of great interest in terms of research, because of their great electrocatalytic properties and high hydrogen production. These alloys even surpass Platinum (Pt), which is the most efficient yet also one of the most expensive metal used as hydrogen production catalyst. The electrodeposition of thin film alloys, offers porous, inexpensive and resistive in basic and acidic environment, compounds. The alloys we fabricated were NiFe, NiFeZn, NiCoZn, NiCoFeZn and NiMoZn. Our main goal was to study the electrodeposition process conditions and the manner in which they affect the morphology and the properties of the thin film alloys. At first we studied the electrocatalytic properties of the thin film alloys during the electrolytic production process using the same conditions every time. The next step was to measure the hydrogen production overvoltage and the estimation of electrocatalytic constants such as the exchange current density and the Tafel slope using the Tafel diagrams. Finally SEM micrographs and EDX stoichiometry analysis gave more accurate results on the morphology and the electrocatalytic properties of the thin film alloys. We also studied the electrocatalytic properties of a new compound (NiCoFeZn), which is in fact a very promising compound for the electrolytic hydrogen production. Today the research around this material is mainly focused on its magnetic properties, so a thorough study of its catalytic properties would be of great importance.

Dealloying refers to the partial, selective dissolution of the less noble component(s) of a binary or ternary alloy precursor, resulting in a noble-rich, porous structure that has high surface area. Such surface structure is beneficial for fuel cells (FC) because FC uses platinum (Pt), a scarce metal, to catalyze the oxygen reduction reaction (ORR) at the cathode surface. In order to characterize the benefit of the dealloying process in FC ORR catalysts with the rotating disk electrode (RDE) technique, a high surface area catalyst support, namely 3M Co’s nanostructured thin film (NSTF), was incorporated into the RDE measurements. NSTF-coated glassy carbon (GC) disks were used in RDE experiments on a Pt/Pt1-xIrx (0.05 < x < 0.3) composition spread. ORR measurements using NSTF-coated GC disks measure the catalytic properties with the same morphology, composition and surface structure as would be found in a fuel cell. A series of Pt1-xCox and Pt1-xNix (0.5 < x < 0.8) dealloy catalyst precursor films were tested using NSTF-coated GC disks in RDE studies. The value of x in Pt1-xMx (M = Ni, Co) was selected to be high in order to examine the dealloying process. The catalyst films were examined by a RDE test protocol that tracked the surface enhancement factor (SEF) and ORR current densities over a large number of test cycles. The aim was to measure the catalytic performance of the Pt-M materials as dealloying took place. The SEF of the PtCo and PtNi materials increased rapidly at the beginning and reached a plateau as high as 50 cm2/cm2 while the specific ORR activities increased as the initial M content in the catalyst precursor increased. The impact of the dealloying process on morphology was examined by completely dealloying a Pt3Ni7 precursor, deposited on mirror-polished GC disks, at a constant potential. As the dealloying process continued, the SEF of the material increased from about 1 cm2/cm2 to > 30 cm2/cm2 and resulted in the formation of whisker-like structures.

In this study SBA-15 mesoporous silica template was synthesized and used as a sacrificial template in the preparation of ordered mesoporous carbon material. A chemical vapour deposition (CVD) technique using LPG or alternatively sucrose, pyrolyzed upon a mesoporous Si matrix were used to produce nanostructured ordered mesoporous carbon (OMC) with graphitic character after removing the Si template. The sucrose method was found to be a suitable route for preparing OMC. The OMC was used as a conductive three dimensional porous support for depositing catalytic nanophase Pt metal. Deposition of Pt nanoparticles on OMC was accomplished using a CVD method with Pt(acac)2 as a precursor. The synthesized nano-composite materials were characterized by several techniques such as, HRTEM, HRSEM, EDS, XRD, BET, TGA, FT-IR and CV.

Made available in DSpace on 2014-10-09T12:28:39Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:57:29Z (GMT). No. of bitstreams: 0 / Dissertacao (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP