La connaissance précise des champs électromagnétiques rayonnés par les dispositifs hyperfréquences nécessite des outils instrumentaux permettant la mesure directe ou indirecte de ces champs. La technique du scan champ proche fait partie de ces outils. Ce manuscrit décrit les travaux de caractérisation des sondes électromagnétiques pour une plate-forme de scan champ proche développée au laboratoire LAPLACE. L’accent a été mis sur la simulation électromagnétique des dispositifs de test utilisés dans le travail de déconvolution du facteur d’antenne des sondes de champs magnétiques ou électriques. Ces dispositifs comprennent aussi bien des structures planaires telles que des interconnexions en ligne microruban que des composants en guide d’ondes tels que des guides ouverts de formes rectangulaire ou circulaire. Pour analyser ces structures des logiciels commerciaux basés sur la méthode des différences finis ont été utilisés. Dans le cas des structures rayonnantes un programme basé sur la méthode de l’opérateur transverse a été développé, permettant la détermination de l’admittance de rayonnement et les champs rayonnés en zones proche et lointaine. Les résultats obtenus ont été validés par des simulations avec des outils commerciaux, et par des mesures réalisés au laboratoire. / The accurate knowledge of electromagnetic fields radiated by microwave devices requires instrumental tools for direct or indirect measurement of these fields. Near-field scan technique is one of those tools. This manuscript describes the work done to characterize electromagnetic probes using a near field scan platform developed in the laboratory LAPLACE. We focused our work on the electromagnetic simulation of test devices that are used in the deconvolution of antenna factor of magnetic or electric probes. These devices include both planar structures such as microstrip line and also waveguide components such as rectangular or circular open-ended waveguides. To analyze these structures, commercial software based on finite element method was used. In case of radiating structures, a program based on transverse operator method was developed. It allows the determination of the admittance of radiation and the radiated electromagnetic fields in near-field and far-field regions. The results were validated by simulations with commercial tools, and measurements made in the laboratory.

Avec la miniaturisation de plus en plus poussée des composants sur silicium, certains phénomènes, connus sous le nom des problèmes de la Compatibilité Électromagnétique peuvent surgir, ils sont les principales causes de la reconception des systèmes intégrés. Ce travail de thèse consiste à développer une méthodologie d'analyse prédictive de la compatibilité électromagnétique pour les systèmes électroniques, par anticipation design. Afin d'aboutir à ce modèle prédictif, différents champs d'investigation ont été mise en place afin d'appréhender l'ensemble du problème. Premièrement, nous avons développé une méthode de prédiction des parasites du boîtier électronique appelée « MCTL Matrix Method ». Cette méthode est issue du principe du prototypage virtuel du boîtier et elle est basée sur des lignes de transmission multiconducteurs. Deuxièmement, nous avons proposé une méthodologie d'analyse de l'immunité du système complet dès les premières phases de la conception. / Modern electronic systems require a high-level of integrations. As a result, some phenomena which are known as ElectroMagnetic Compatibility (EMC) issues are arising, and they are the major causes of system redesign. This main objective of this work is to develop a predictive methodology for systems immunity. To do so, different fields have been investigated: first, we have developed a predictive method for package parasites called “MCTL Matrix Method” which is based on a virtual package prototyping and Multiconductor transmission lines. Then we have proposed a new methodology for system immunity at the earliest design stages.

De nos jours, on assiste à l'émergence massive de nouveaux systèmes électroniques exploitant des fréquences de plus en plus élevées, particulièrement en ondes millimétriques (30-300 GHz). Il apparaît de ce fait un besoin potentiel de développement de nouveaux moyens d'essai appropriés dans le domaine millimétrique. En particulier, l'étude de la biocompatibilité de ces systèmes est clairement identifiée comme une priorité de recherche en électromagnétisme. Dans ce contexte, l'objectif de cette thèse consiste à concevoir et à évaluer les propriétés d'une chambre réverbérante à brassage de modes (CRBM) en bande Ka (26,5-40 GHz), en bande U (40-60 GHz) et en bande V (50-75 GHz). L'application visée dans cette thèse concerne la mise en place d'outils dosimétriques par caméra infrarouge en chambre réverbérante et la réalisation d'essais préliminaires sur des fantômes diélectriques à 60 GHz. Dans un premier temps, nous avons analysé numériquement le comportement statistique du champ électrique dans une cavité pré-dimensionnée. Les simulations sont réalisées à l'aide d'un outil interne de modélisation du comportement d'une CRBM basé sur la théorie des images. A l'aide du test d'ajustement statistique d'Anderson-Darling, nous avons montré que le comportement de la chambre en ondes millimétriques est en adéquation avec le modèle de Hill (champ statistiquement homogène et isotrope dans le volume de l'enceinte) . Dans un second temps, nous avons réalisé un prototype de chambre réverbérante de dimensions internes : 42,3 x 41,2 x 38,3 cm3 . Un processus de brassage par saut de fréquence est utilisé pour l'obtention de l'uniformité statistique de la densité de puissance. La chambre est équipée d'un système de positionnement fin et précis permettant l'échantillonnage spatial de la puissance sur un axe à l'intérieur de la chambre. Les accès millimétriques ont également été étudiés de sorte à réduire d'éventuelles fuites significatives. Les liaisons entre la source millimétrique et l'antenne d'émission d'une part et celles entre l'antenne de réception et l'analyseur de spectre d'autre part sont assurées par des guides d'onde. Nous avons également mis en place l'ensemble des équipements nécessaires pour le fonctionnement de la chambre (source, analyseur de spectre, mélangeur). La chambre est caractérisée dans la bande 58,5-61,5 GHz. Les résultats obtenus sont satisfaisants en termes de coefficient de qualité et de comportement statistique de la puissance mesurée dans un volume de test donné. Dans un troisième temps, nous avons modélisé puis réalisé une interface intégrée sur une des parois de la chambre pour la mesure de température par caméra infrarouge. Des mesures préliminaires sont réalisées sur un fantôme constitué essentiellement d'eau. Les résultats expérimentaux et théoriques de l'évaluation du gradient de la température sur le fantôme sont très proches. Ceci confirme que la chambre réverbérante ainsi conçue permet de soumettre l'objet sous test à une illumination statistiquement uniforme et calibrée en puissance. Un tel dispositif est un atout précieux pour des tests de compatibilité électromagnétique d'équipements électroniques dans la bande 26,5-75 GHz. Cette CRBM pourrait également permettre de réal iser des essais préliminaires dans le cadre de l'étude des interactions des ondes avec la matière vivante en millimétrique. / Nowadays, there is a massive emergence of new electronic systems operating at increasing frequencies, especially in the millimeter waves range (30-300 GHz). As a consequence, development of new appropriate test facilities in the millimeter waves range is needed. ln particular, the study of the biocompatibility of the se systems is cie arly identified as a research priority in electromagnetism. ln this context, this thesis deals with the design and the evaluation of a modestirred reverberation chamber (RC) properties in the Ka band (26.5-40 GHz), U band (40-60 GHz) and V band (50-75 GHz). The intended application in this thesis concerns the development of a dosimetric tool using an infrared camera in a reverberation chamber. Firstly, we numerically analyze the statistical behavior of the electric field in the test volume of such an RC. A numerical model based on image theory is used to simulate the cavity. With Anderson-Darling goodness-of-fit test, we show !hat the chamber behaves very weil at millimeter waves frequency in terms of statistical distribution of the field in the test volume. Secondly, a compact reverberation chamber is designed and built up, with the following internai dimensions 42.3 x 41.2 x 38.3 cm3 . The statistical uniformity of power density in the chamber volume is obtained by frequency stirring. The RC is associated with a positioning system for spatial sampling of power inside reverberation chamber. The interfaces are also studied in order to reduce any significant leakage. Waveguides are used in the transmission and reception chains to minimize losses. We have also set up ali the equipment necessary for carrying out measurements (source, spectrum analyzer, mixer). The RC is characterized in the 58.5-61.5 GHz range. The results are satisfactory in terms of the quality factor level and the statistical distribution of the power in the test volume. Thirdly, an interface is designed and integrated on one of the chamber walls for temperature measurement by an infrared camera. Preliminary measurements are performed on a phantom consisting essentially of water. Experimental results of the phantom temperature rise are in good agreement with theoretical predictions. This confirms thal the designed reverberation chamber allows to expose the deviee under test with a statistically uniform and calibrated power. Such a deviee is a valuable asse! for EMC testing of electronic equipments in the 26.5 to 60 GHz frequency range. This RC could also permit to conduct preliminary tests in the context of the millimeter waves interactions with being organisms.

The aim of this thesis is to inform readers about the basic principle of electronics for which the service module for the automatic sanitary technique will be designed, as well as design and describe the most important parts of the module theoretically. Likewise, the thesis deals with the most common mistakes in the design of printed circuits boards with respect to the resistance of the resulting device against interference. The implementation itself includes both module design and a communication algorithm for connecting multiple service modules and their remote control using the Raspberry Pi minicomputer. The thesis also contains a design of algorithm for verification of data transmission by the transmission system.

This diploma thesis deals with the issue of EMC of tram vehicles and traction system. The first chapter defines the issues that are then dealt with in the thesis. The next chapter lists the objectives of the work. Subsequent chapters analyze the issues described in chapter 2. In the last chapter, a flow chart is proposed, which should serve as a tool to estimate the hazards of the traction drive due to induced bearing currents.

Die Elektromagnetische Verträglichkeit (EMV) betrachtet die Fähigkeit eines elektrischen Gerätes, in seiner elektromagnetischen Umgebung störungsfrei zu funktionieren, ohne diese dabei unzulässig zu stören. Zur Prüfung der Elektromagnetischen Verträglichkeit werden verschiedene Messumgebungen verwendet. Die Messung der strahlungsgebundenen Störfestigkeit und Störaussendung kann zum Beispiel in einer Modenverwirbelungskammer (MVK) erfolgen. Bei der Störfestigkeitsmessung wird der Prüfling einem externen Prüffeld ausgesetzt und untersucht, ob dieser die definierten Kriterien für einen störungsfreien Betrieb erfüllt. Für das Prüffeld muss vor der Messung nachgewiesen werden, dass die Anforderungen an dessen Homogenität eingehalten werden. Einen entscheidenden Einfluss auf die Homogenität des Prüffeldes hat der sogenannte Rührer. Bei einer MVK handelt es sich prinzipiell um einen Hohlraumresonator, in den ein mechanischer Rührer, d.h. ein elektrisch großer, drehbarer Streukörper integriert wird. Durch die Drehung des Rührers verändert sich die Feldverteilung in der MVK, was auch als Verwirbelung bezeichnet wird. Prinzipiell ergibt sich für jede Stellung des Rührers ein inhomogenes Feld mit lokalen Minima und Maxima. Ein Ziel bei der Verwendung von Modenverwirbelungskammern ist es, mit Hilfe geeigneter Verfahren Rührerstellungen zu finden, deren Feldverteilungen in Überlagerung ein möglichst homogenes Prüffeld erzeugen. Zum Lehrstuhl für Theoretische Elektrotechnik und Elektromagnetische Verträglichkeit der Technischen Universität Dresden gehört seit 2010 eine Modenverwirbelungskammer. Die Charakterisierung dieser MVK sowie eine weiterführende Untersuchung zur Wahl der Rührerstellungen bilden die Schwerpunkte der vorliegenden Arbeit. / In 2010 the Chair of Electromagnetic Theory and Compatibility of Technical University Dresden could extend its laboratories by a reverberation chamber with the dimensions 5.3 m, 3.7m and 3.0 m. Since then, a detailed characterisation of the chamber as well as further investigations have been the main emphasis of the authors research. The submitted doctoral thesis presents the obtained results. With the design, the fundamentals of operation and further characterisation of the reverberation chamber, given in Chapter 1 and 2, it aims to give an introduction and better understanding of reverberation chambers. On this basis, the authors research focused on methods for determining the independent stirrer positions in reverberations chambers. The results of the investigations are presented and summarised in chapter 3. One scope of Electromagnetic Compatibility are radiated immunity measurements. Besides the GTEM cell and the anechoic chamber the reverberation chamber gains in importance as an alternative measurement environment. A reverberation chamber is a shielded room with reflecting walls and one or more integrated mechanical stirrers. By rotating the stirrer the spatial boundary conditions for the electromagnetic field quantities are altered. The resulting change of the spatial field distribution depends on the location within the chamber and the geometry of the stirrer. Each stirrer position yields an inhomogeneous field distribution created by interfering waves. A general aim is to find a set of stirrer positions, whose superimposed field distributions create a more uniform test field. In practice, the given requirements for the homogeneity of the test field shall, with regards to an optimisation of measurement time, be realized with a minimum number of stirrer positions. In this context the term ’independent stirrer positions’ was established and describes stirrer positions, whose field distributions are linearly uncorrelated and therefore assumed to be practical for creating a more homogeneous test field using only a minimal number of stirrer positions. A general method for determining the number of independent stirrer positions in reverberation chambers is presented. The method uses a certain number of measurement positions in a defined test volume in order to characterize the spatial field distribution inside the chamber. Using the Pearson correlation coefficient the field distributions of the stirrer positions are tested for linear correlation and pairs of independent stirrer positions are determined. On this basis, cliques of pairwise independent stirrer positions are identified using appropriate algorithms. It is shown that the general method yields detailed information about the number and distribution of the independent stirrer positions and is therefore particularly suitable to evaluate other methods. Finally, the standard method according to IEC 61000-4-21 as well as selected alternative methods, that have been proposed in the past, are evaluated and compared based on the results of the general method.

<div>The high-frequency switching of transistors in power electronic (PE) converters is known to cause unintended common-mode (CM) current that flows through parasitically-coupled ground paths. One way to model these currents is to utilize time-domain simulations that capture switching dynamics and the corresponding parasitic response. Although potentially useful, the small time steps required can create a computational burden and limit the usefulness of the approach. In addition, access to internal hardware needed to characterize parasitic parameters is often limited.</div><div><br></div><div>In this thesis, frequency-domain Thevenin equivalent circuits (TECs) are derived to model the CM behavior of PE converters. To do so, periodic linear time-varying (PLTV) analysis is used to develop Thevenin-like models that account for switching behavior of PE circuits. Subsequently, it is shown that in many applications these PLTV TECs can be reduced to traditional linear time-invariant (LTI) forms. Methods to experimentally characterize LTI TEC parameters and couple multiple TECs together for system-level analysis are then established. Finally, the TEC approach is extended to model converters in which common- and differential-mode (CM/DM) behavior are strongly coupled. Simulation and experimental results are used to validate the proposed TEC techniques.</div>

Le développement d’aéronefs « plus » voire « tout » électriques a pour conséquence la conception d’architectures électriques embarquées de plus en plus complexes entraînant une très nette augmentation du nombre de câbles électriques à déployer au sein des véhicules. Parmi les contraintes rencontrées lors des phases de définition et d’intégration des réseaux de câblages, les aspects de compatibilité électromagnétique et de gestion des échauffements thermiques deviennent de plus en plus critiques. Ainsi, ces travaux de thèse sont dédiés au développement d’une méthodologie permettant la prédiction d’une part, des courants induits par et sur les réseaux de câblages et d’autre part, de leur niveaux d’échauffement. En particulier, l’analyse bibliographique effectuée à cette occasion montre que les phénomènes électrostatiques (à la base de la théorie des lignes de transmission) et de conduction stationnaire de la chaleur sont strictement analogues, ce qui autorise une résolution simultanée de ces deux problèmes pour les réseaux de câblages considérés. Les présents travaux démontrent que le calcul des paramètres électriques primaires (p.u.l) du réseau et de la distribution de température dans le plan transverse peut se faire de manière totalement couplé à l’aide d’un schéma numérique basé sur la Méthode des Moments(MoM). Le choix de l’utilisation des équations intégrales pour la résolution de ce problème de potentiel se fonde sur plusieurs avantages tels qu’une utilisation optimisée des ressources de calcul et l’utilisation d’algorithmes efficaces de résolution, de surcroît naturellement parallélisables pour de futurs développements. Les outils de calculs thermiques développés dans le cadre de cette thèse, et qui ont vocation à être intégrés dans la suite logicielle CRIPTE de l’ONERA, ont fait l’objet d’une validation expérimentale pour plusieurs configurations de harnais électriques. Les comparaisons simulations-mesures présentent de bons accords bien que les expérimentations menées aient montré la difficulté d’obtenir précisément des valeurs du coefficient d’échange thermique,même dans des conditions parfaitement maîtrisées. Les travaux ouvrent enfin des perspectives nouvelles sur l’optimisation en terme de masse des réseaux de câblage (EWIS). / The on-going development of “more” or “all” electrical aircraft leads to the design of ever-complex embeddedelectrical networks, which causes a significant increase of electrical cables to be used within these innovativevehicles. Among the constraints encountered during the definition and integration phases of the network, thoserelated to the electromagnetic compatibility between equipment as well as the management of thermal heatingby Joule’s effect become more and more stringent. Thus, this thesis is dedicated to the development of anoriginal methodology enabling the prediction of both induced and crosstalk currents as well as the heating upstate in complex bundles of cables. Indeed, literature review explicitly shows that electrostatic and stationaryheat transfer phenomena are, from a mathematical standpoint, strictly the same which allows the simultaneouscomputation of these two problems for an arbitrary network. This research work demonstrates that the determinationof primary electrical parameters (per unit length) and the temperature distribution within a givencross-section can be handled with the numerical Method Of Moment (MoM). This choice is motivated by theseveral inherent advantages of the method like an optimized use of the computer resource and the naturalparallelization of the algorithms. The developed numerical tools, intended to be fully integrated in the in-housesoftware suite CRIPTE, has been validated during an experimental campaign that has involved several typesof bundles. Although the comparisons between experimental and simulated results comply with each other,experiments reveal the hard task of getting a precise estimation of the heat transfer coefficients, even in awell-controlled environment. Finally, these works open new and very promising perspectives for future EWIS(Electrical Wiring Interconnection System) in term of mass optimization.

Nos últimos 20 anos, o inversor de frequência PWM passou a ser largamente utilizado. Dentre as razões principais de sua ampla difusão, cita-se a introdução do IGBT que, devido à sua capacidade de comutação rápida, possibilitou a redução de perdas, tamanho e custo dos conversores, ao mesmo tempo em que permitiu o uso do motor de indução em aplicações que demandam alto desempenho dinâmico. Porém, esta mesma característica que trouxe tais benefícios, contribuiu para acentuar os efeitos relacionados a fenômenos eletromagnéticos, devido à rápida transição que produz sinais em alta frequência, responsáveis por tornar os sistemas de acionamentos potenciais fontes de interferência eletromagnética. Os principais fenômenos desta natureza são a tensão de onda refletida, associada a ruídos de modo diferencial, e a corrente de modo comum. De maneira geral, a corrente de modo comum tem maior potencial de contribuição para a emissão radiada que a de modo diferencial e, em sistemas de acionamento, constitui a principal fonte de interferência eletromagnética. Esta não é resultado apenas da rápida comutação dos IGBTs, mas, também, da configuração do sistema, que propicia o surgimento das tensões de modo comum. Este trabalho visa estudar alternativas que minimizem, naturalmente, estas tensões através de sua configuração, reduzindo-se a necessidade de novos componentes, como filtros passivos ou circuitos ativos. Ressalta-se, assim, que o primeiro passo consistiu-se na compreensão do problema de geração da tensão de modo comum. Visando atingir os propósitos anteriormente mencionados, foi idealizado um inversor, composto de duas pontes chaveando em oposição, chamado de duplo-trifásico. A partir de simulações, avaliou-se seu potencial e definiu-se sua implementação, a partir de dois inversores idênticos. Testou-se o protótipo contra um terceiro módulo de mesmo tipo, em iguais condições. A comparação dos resultados indicou que a configuração proposta pode ser eficiente no controle do ruído de modo comum, obtendo-se valores de redução de 86%. Nota-se que o comportamento observado via o protótipo, permite um melhor entendimento dos fenômenos relativos à circulação da corrente de modo comum. Desta forma, à luz da pesquisa realizada, nota-se que, conceitualmente, a solução proposta se destaca das demais apresentadas na literatura pela sua exequibilidade e simplicidade. / Over the last 20 years, the PWM frequency inverter has become widely used. Among the main reasons for its widespread distribution is the introduction of the IGBT, due to its ability for fast switching allowing the reduction of losses, size and cost of the converters, and the use of the induction motor in applications that demand high dynamic performance. However, this same characteristic that brought such benefits, stressed the effects related to electromagnetic phenomena, due to the fast transition that produces high frequency signals, responsible for turning drive systems, potential sources of electromagnetic interference. The main phenomena of this nature are the reflected wave overvoltage, associated with differential mode noise, and the common mode current. In general, the common mode current has greater potential of contribution to the emission of radiated interference than the differential mode current and is the main source of electromagnetic interference in drive systems. The common mode current is not just the result of the fast transitions of IGBTs, but also of the system configuration, which produces common mode voltages. This work aims to study alternatives that minimize, naturally, those voltages through its configuration, reducing the need for additional components, such as passive filters or active circuits. It is pointed, that the first step consisted in the understanding of the problem of the common mode voltage generation. In order to address this objective, an inverter composed of two bridges, switching in opposition, called double-three-phase was designed. Its potential for noise mitigation, as well, its implementation, with two identical inverters was evaluated by simulations. The prototype was tested against a third module of the same type, under the same conditions. The comparison of the results indicated that the proposed configuration can be efficient in the common mode noise control, with 86% reduction. The behavior observed through the prototype allows a better understanding of the phenomena involving common mode current. Thus, in the light of the research, we note that, conceptually, the proposed solution stands out for its practicality and simplicity, from the others presented in the literature.

Submitted by SBI Biblioteca Digital (sbi.bibliotecadigital@puc-campinas.edu.br) on 2018-05-09T13:04:20Z No. of bitstreams: 1 GUSTAVO IERVOLINO DE MORAIS.pdf: 4929600 bytes, checksum: 01e42f70e6b846ac7004d007a1459140 (MD5) / Made available in DSpace on 2018-05-09T13:04:20Z (GMT). No. of bitstreams: 1 GUSTAVO IERVOLINO DE MORAIS.pdf: 4929600 bytes, checksum: 01e42f70e6b846ac7004d007a1459140 (MD5) Previous issue date: 2018-02-26 / Household appliances are not certified to be marketed in Brazil as regards emission aspects of electromagnetic disturbance, which may affect the functionalities of telecommunications systems, as well as the advancement of technologies, such as IoT (Internet of Things), being the WSN widely used within Iot, due to its flexibility and the low cost. This work evaluates the levels of electromagnetic disturbances generated by household appliances and how much these disturbances can affect the functioning of WSN. The work was divided in 3 stages and in all of them the Semi-Anechoic Chamber was used, being the first stage the evaluation of the electromagnetic disturbances of the household appliances, if they meet the normative requirements used in Europe, secondly a characterization of the WSN, being evaluated the RSSI and the PER, and finally the appliance with the highest interfering level was placed with the WSN to evaluate RSSI and PER. The results showed that the household appliances do not meet the normative limits and significantly affect the functioning of an WSN. / Os equipamentos eletrodom?sticos n?o possuem certifica??o para serem comercializados no Brasil quanto aos aspectos de emiss?o de perturba??o eletromagn?tica o que pode afetar as funcionalidades dos sistemas de telecomunica??es, bem como o avan?o de tecnologias, como por exemplo, o IoT (Internet das coisas), sendo a RSSF amplamente utilizada dentro de Iot, devido sua flexibilidade e o baixo custo. Este trabalho avalia os n?veis das perturba??es eletromagn?ticas geradas pelos equipamentos eletrodom?sticos e o quanto estas perturba??es podem afetar o funcionamento de RSSF. O trabalho foi dividido em 3 etapas e em todas elas foram utilizadas a C?mara Semi-anec?ica, sendo a primeira etapa a avalia??o das perturba??es eletromagn?ticas dos equipamentos eletrodom?sticos, se atendem aos requisitos normativos utilizados na Europa, em segundo uma caracteriza??o da RSSF, sendo avaliado a RSSI e a PER, e por ?ltimo o eletrodom?stico com maior n?vel interferente foi colocado junto a RSSF para avalia??o de RSSI e da PER. Os resultados obtidos demonstraram que os equipamentos eletrodom?sticos n?o atendem aos limites normativos e afetam significativamente o funcionamento de um RSSF.