<p>The continuing shrinkage of semiconductor devices towards nanoscale features and increased functionality has prompted a strong need for high-resolution characterization tools capable of mapping the electrical properties with nanoscale lateral resolution. In this regard, scanning capacitance microscopy (SCM) scanning spreading resistance microscopy (SSRM) and Kelvin probe force microscopy (KPFM) have emerged as powerful techniques. </p><p>This thesis focuses on new applications of these techniques for the electrical characterization of III-V materials, devices and low-dimensional systems. One example is the investigation of GaAs/AlGaAs buried-heterostructure lasers with cross-sectional SCM. Several important issues have been addressed: nanoscale contrast related to local band structure, characterization of interfaces and evaluation of electrical properties of the regrown layers. These investigations demonstrate the ability of SCM for reliable, non-destructive and high resolution analysis of opto-electronic devices. </p><p>Applications of SCM and SSRM as potential in-line evaluation tool for III-V processing are demonstrated. In this scope, the first work deals with the characterization of ion beam implanted InP, a promising approach to achieve ultrashort carrier lifetimes. The changes in the local electrical properties of this material induced by annealing are tracked. SCM and SSRM measurements were crucial in identifying the local regions of different conductivity due to the non-uniform damage profiles. The results are correlated with those obtained by complementary structural, electrical and optical characterization. The second work in this category establishes the utility of SCM for evaluating the impact of dry etching on the electrical properties of InP. The highly conductive nature of the near surface damaged layer and its subsequent recovery upon annealing is evidenced. A striking correlation between the SCM signal distributions and the ideality factors of macroscopic Schottky contact is observed. </p><p>The last part deals with the electrical characterization of low-dimensional systems using SCM, SSRM and KPFM. The challenging issues motivating this work are the detection and quantification of confined carriers, the determination of band-offsets and the determination of the spatial resolution of the technique employed. The ability of SCM, SSRM and KPFM to detect carriers accumulated in InGaAs/InP quantum wells (QWs) is demonstrated. In each of these techniques, the physical mechanisms behind the contrast characteristic obtained at QWs are elucidated. The specific issues relating to the determination of the band-offsets are discussed. A new method to determine the "electrical" spatial resolution of SCM and SSRM is addressed using quantum well structures with varying inter-well spacings. Using commercial probes, sub-30 nm and sub-5 nm lateral resolution are determined for SCM and SSRM, respectively. The experimental conditions to perform high resolution measurements are identified.</p>

<p>On this thesis project, the LMS algorithm has been applied for speech noise filteringand different behaviors were tested under different circumstances by using Matlabsimulations and the LPC2378 ARM Processor, which does the task of filtering in realtime. The thesis project is divided into two parts: the theoretical and practical part.</p><p>In the theoretical part there is a brief description of the different aspects of signalprocessing systems, filter theory, and a general description of the Least-Mean-SquareAdaptive Filter Algorithm.</p><p>In the practical part of the report a general description of the procedure will besummarized, the results of the tests that were conducted will be analyzed, a generaldiscussion of the problems that were encounter during the simulations will be mention,and suggestion for the problems will be given.</p>

<p>This thesis discuss on new technique called space time block coding (especially Alamouti's code) which is used to increase capacity and reliability of data transmission over time varying multi-path fading channel. The over all work of the thesis included in the following four chapters.</p><p>In chapter-1 we are going to cover some theoretical part which is useful to understand thesis work and in chapter-2 we will discuss the comparison between simple space time block code (Alamouti's code) and MRRC (Maximum Ratio Receiver Combining) which is receiver diversity and then in chapter-3 we will see the channel capacity & probability error performance for 2x2 Alamouti code over Rayleigh and Rice fading channel .Finally the conclusion and further work included in chapter-4.</p>

<p>This thesis presents a study of the effects of inter-bar currents on inductionmotor starting performance and stray-load losses. The work is focused on theperformance differences between aluminium and copper casted rotors.A method to predict the stator current when starting direct-on-line isdeveloped. This includes modelling of skin-effect, saturation of the leakageflux paths and additional iron losses. The results are verified by measurements.An analytical model accounting for inter-bar currents is derived, andthe dependency of the harmonic rotor currents on the inter-bar resistivity isinvestigated. It is found that the inter-bar currents can have considerableeffect on motor starting performance and stray-load losses, the amount beingstrongly dependent on the harmonic content of the primary MMF.Based on measurements of inter-bar resistivity, the starting performanceof an aluminium and a copper casted rotor is simulated. The results indicatea higher pull-out torque of the aluminium rotor than for the equivalent copperrotor. This is rather due to an increase of the fundamental starting torque ofthe aluminium rotor, than due to braking torques from the space harmonicsin the copper rotor. The results are verified by measurements. It is foundthat the difference between the pull-out torques is even larger than calculatedfrom the model. Thereby, it can be concluded that the inter-bar currents havea considerable effect on motor starting performance.At rated speed the braking torques are larger in the aluminium rotor thanin the copper rotor. This is seen as increased harmonic joule losses in the rotorcage. Simulations have shown, that these losses can be as large as 1% ofthe output power for the studied machine.</p> / QC20100617

<p>Rapid development in CMOS technology has resulted in its suitability for the implementation of readout front-end systems in terms of high integration density, and low power consumption yet at the same time posing many challenges for analog circuits design like readout front-end. One of the significant challenges is the low noise design for high speed front-end systems, while at the same time minimizing the power consumption as much as possible.</p><p>A high speed, low noise, low power, and programmable readout front-end system is designed and implemented for an X-ray detector in CMOS 0.18 m technology in this thesis work. The front-end system has a peaking time of 10 ns, which is the highest speed ever reported in the published work. The front-end system is designed to achieve low noise in terms of ENC, and a low power consumption of 2.9 mW. The detector capacitance is the most dominating parameter to low noise, which in turn is directly related to the power consumption. In this thesis work an ENC of 435 electrons is achieved for a detector capacitance of 5 pF and an ENC of 320 electrons for a detector capacitance of 3 pF. Based on the comparison to related published work, a performance improvement of at least two times is achieved taking peaking time, power, ENC, and detector capacitance all into consideration. The output pulse after amplification has peak amplitude of 300 mV for a maximum injected charge of 40000 electrons from the detector.</p><p>The readout front-end system noise performance is strongly dependent on the input MOSFET type, size, and biasing. In this work a PMOS has been selected and optimized as the input device due to its smaller 1/f noise and high gain as compare to NMOS when biased at same currents. The architecture designed in this work consists of a folded cascode CSA with extra cascode in first stage, a pole-zero cancellation circuit to eliminate undershoot, a shaper amplifier, and integrators using Gm-C filter technique. All of these components are optimized for low power while meeting the noise requirements. The whole front-end system is programmed for peaking times of 10, 20, and 40 ns. The programmability is achieved by switching different capacitors and resistors values for all the poles and zeros in the front-end, and by switching parallel transconductance in the Gm-C filters. Finally fine tuning of all the capacitance, resistance, and transconductance values is done to achieve required performance.</p>

<p>In today’s world the multi-standard wireless receivers are gaining more and more popularity. End-users want to access voice, data and streaming media from a single wireless terminal. An ideal approach for multi-standard receiver front-end is to digitize a wide band RF signal available from the antenna. All radio functions such as downconversion, demodulation and channel selection can be then performed in the digital domain. Analog to Digital Converter in such a case should guarantee very high linearity, speed and bandwidth specifications while consuming a lot of power. Unfortunately an ADC with such stringent requirements cannot be realized in today’s CMOS technology. In a typical receiver a mixer is used to downconvert the RF signal to baseband (or IF) before digitization is performed. A passive mixer is often used in this case to mitigate the effect of the low frequency flicker noise. Specially it can be a sampling mixer which also serves as a S/H circuit usually required for A/D conversion. In this thesis a lowpass sigma-delta converter with RF sampling is presented. The ΣΔ modulator is SC passive circuit plus comparator, so an operational amplifier usually needed to realize the integrator is avoided. To reduce the complexity, the sampling mixer in front of the modulator is merged with the passive loop filter. As a result the sampling mixer is closed in the modulator loop, so the overall linearity of the frontend is improved to some extent. Downconversion is combined with digitization that reduces the circuit complexity as well.The challenges while digitizing high frequency RF signal are discussed in details. Switches required to realize the loop filter are very critical and tend to be nonlinear. Parasitic effects associated with MOS transistors strongly show up at GHz frequencies. Optimized transistor sizes are obtained through simulation while addressing the speed and linearity trade-off. Another major challenge is the kT/C noise that is the real bottleneck in high frequency SC circuit design. A thermal noise model for ΣΔ-modulator with second-order loop filter is presented and it is shown that a passive ΣΔ-modulator is  in fact thermal noise limited rather than quantization noise limited. It is because the capacitor values are limited by the very high sampling frequency used in this case.The downconverting lowpass ΣΔ modulator with second order SC passive loop filter and 1-bit quantizer is simulated at transistor level in 90nm CMOS process. This modulator can operate at very high sampling frequency upto 4GHz and can sample RF signal with carrier of upto 4GHz as well. The designed ΣΔ modulator is flexible and supports sub-sampling by 2 to 8 (fs = 500MHz, ... 2GHz). Besides, the presented design is very power efficient as it does not use OpAmps – which consume most of the power in the typical ΣΔ modulators. From schematic simulation on average, signal-to-noise and distortion ratio (SNDR) of 52 dB is obtained (ENOB = 8.3). SNDR results does not vary much for three different cases of baseband digitalization, RF sampling and RF sub-sampling. This SNDR value seems to be a good number for a passive sigma-delta modulator. The detailed simulation results for the three cases discussed in the thesis work shown that, the modulator performs equally well for a wide range of sampling and RF signal frequencies.</p>

<p>A wave digital filter is derived from an analog filter, which is realized as classical doubly resistively terminated reactancefilters. Perfectly designed wave digital filters express good dynamic signal range, low roundoff noise and excellent stabilitycharacteristics with respect to nonlinearity which are produced due to finite wordlength effects. Wave digital filters inheritthe sensitivity properties from analog filters, therefore, coefficients values can be selected to favorable values.Wave digital filters, derived from ladder filters, have low coefficient sensitivity in the passband and stopband. These WDFsare very complicated and are non-modular. The lattice wave digital filters are modular and are not complex. However, theyhave very high sensitivity in the stopband and thus require large coefficient wordlengths. The number of coefficients equalsthe filter order which have to be odd.This thesis discusses the wave digital filter structures that are modular because they are designed by cascading the first-orderand second-order sections. These WDFs can be pipelined. They also exhibit all the above mentioned favorable properties.Similar to lattice WDFs, these structures are restricted to symmetrical and antisymmetrical transfer functions. The synthesisof these structures is based on the factorization of the scattering matrix of lossless two-ports.In this thesis work, lowpass wave digital filters based on circulator-tree structure are designed with different orders startingfrom 3 and going upto 13. In parallel to these circulator-tree wave digital filters, the simple digital filters are also designedwith the same specification. The results of the two filters are compared with each other. It is observed that impulse responseand attenuation response of the two kind of filters perfectly match. Therefore, it is can be concluded that circulator-tree WDFupto Nth order can be synthesized. The implementation examples of two filter with order 3 and order 7 is presented in thisdocumentation for ready reference. It has also been shown that the order of sections does not affect the transfer function ofthe filter. Noise has been introduced and adaptor sections are penetrated. From the results it is concluded that the order of theadaptor sections does not matter and also that the noise does not affect the other adaptors sections, it only propagates throughother adaptors sections.</p>

<p>At Acreo AB located in Norrköping, Sweden, research and development in the field of organic electronics have been conducted since 1998. Several electronic devices and systems have been realized. In late 2003 a commercial printing press was installed to test large scale production of these devices. Prior to the summer of 2005 the project made significant progress. As a step towards industrialisation, the variability and yield of the printing process needed to bee studied. A decision to implement Statistical Process Control (SPC) and Design of Experiments (DOE) to evaluate and improve the process was taken.</p><p>SPC has been implemented on the EC-patterning step in the process. A total of 26 Samples were taken during the period October-December 2005. An - and s-chart were constructed from these samples. The charts clearly show that the process is not in statistical control. Investigations of what causes the variation in the process have been performed. The following root causes to variation has been found: </p><p>PEDOT:PSS-substrate sheet resistance and poorly cleaned screen printing drums. </p><p>After removing points affected by root causes, the process is still not in control. Further investigations are needed to get the process in control. Examples of where to go next is presented in the report. In the DOE part a four factor full factorial experiment was performed. The goal with the experiment was to find how different factors affects switch time and life length of an electrochromic display. The four factors investigated were: Electrolyte, Additive, Web speed and Encapsulation. All statistical analysis was performed using Minitab 14. The analysis of measurements from one day and seven days after printing showed that:</p><p>- Changing Electrolyte from E230 to E235 has small effect on the switch time</p><p>- Adding additives Add1 and Add2 decreases the switch time after 1 and 7 days</p><p>- Increasing web speed decreases the switch time after 1 and 7 days </p><p>- Encapsulation before UV-step decreases the switch time after 7 days</p>

<p>This study was initiated to investigate if it could be feasible to supply offshore oil installations in the North Sea with electrical power from land. A prestudy of alternative converter topologies indicated that the most promising solution would be to investigate a conventional system with reduced synchronous compensator rating.</p><p>The study starts with a summary of the state of power supply to offshore installations today, and a short review of classical HVDC transmission. It goes on to analyse how a passive network without sources influences the inverter. The transmission, with its current controlled rectifier and large inductance, is simulated as a current source. Under these circumstances the analysis shows that the network frequency has to adapt in order to keep the active and reactive power balance until the controllers are able to react. The concept of firing angle for a thyristor is limited in a system with variable frequency, the actual control parameter is the firing delay time.</p><p>Sensitivity analysis showed some astonishing consequences. The frequency rises both by an increase in the active and in the reactive load. The voltage falls by an increase in the active load, but rises by an increase in the inductive load.</p><p>Two different control principles for the system of inverter, synchronous compensator and load are defined. The first takes the reference for the firing delay time from the fundamental voltage at the point of common coupling. The second takes the reference for the firing delay time from the simulated EMF of the synchronous compensator. Of these, the second is the more stable and should be chosen as the basis for a possible control system.</p><p>Two simulation tools are applied. The first is a quasi-phasor model running on Matlab with Simulink. The other is a time domain model in KREAN. The time domain model is primarily used for the verification of the quasi-phasor model, and shows that quasi-phasors is still a valuable tool for making a quick analysis of the main features when the details of the transients are of less importance.</p><p>The study indicates that power supply by HVDC transmission from land to offshore oil installations could be technically feasible, even without the large synchronous compensators normally required. It has been shown that in a network only supplied by an inverter, variations of active and reactive loads have significant influence on both voltage and frequency. Particularly it should be noted that the frequency shows a positive sensitivity to increases in load. This could make the system intrinsically unstable in the case of a frequency dependent load such as motors.</p><p>It was not a part of the study to optimize controllers, but even with simple controllers it was possible to keep the frequency within limits given by norms and regulations, but the voltages were dynamically outside the limits, though not very far. These voltage overswings take place in the first few instances after a disturbance, so it takes unrealistically fast controllers to handle them. They are partly due to the model, where the land based rectifier and the DC reactors are simulated by a constant current source, but partly they have to be handled by overdimensioning of the system.</p><p>The simulations indicate that it should be technically possible to supply an oil platform with electrical power from land by means of HVDC transmission with small synchronous compensators. Whether this is financially feasible has not been investigated. Neither has it been considered whether the necessary equipment can actually be installed on an oil platform.</p><p>Recently both ABB and Siemens have presented solutions for HVDC transmission in the lower and medium power range based on voltage source converters based on IGBTs. Fully controllable voltage source HVDC converters have properties that may be better suited than conventional line commutated current source thyristor inverters, to supply weak or passive networks, such as offshore oil installations, with electrical power. But they also have some disadvantages, and a complete technical and financial comparison must be performed in order to decide about any potential project.</p>

This study was initiated to investigate if it could be feasible to supply offshore oil installations in the North Sea with electrical power from land. A prestudy of alternative converter topologies indicated that the most promising solution would be to investigate a conventional system with reduced synchronous compensator rating. The study starts with a summary of the state of power supply to offshore installations today, and a short review of classical HVDC transmission. It goes on to analyse how a passive network without sources influences the inverter. The transmission, with its current controlled rectifier and large inductance, is simulated as a current source. Under these circumstances the analysis shows that the network frequency has to adapt in order to keep the active and reactive power balance until the controllers are able to react. The concept of firing angle for a thyristor is limited in a system with variable frequency, the actual control parameter is the firing delay time. Sensitivity analysis showed some astonishing consequences. The frequency rises both by an increase in the active and in the reactive load. The voltage falls by an increase in the active load, but rises by an increase in the inductive load. Two different control principles for the system of inverter, synchronous compensator and load are defined. The first takes the reference for the firing delay time from the fundamental voltage at the point of common coupling. The second takes the reference for the firing delay time from the simulated EMF of the synchronous compensator. Of these, the second is the more stable and should be chosen as the basis for a possible control system. Two simulation tools are applied. The first is a quasi-phasor model running on Matlab with Simulink. The other is a time domain model in KREAN. The time domain model is primarily used for the verification of the quasi-phasor model, and shows that quasi-phasors is still a valuable tool for making a quick analysis of the main features when the details of the transients are of less importance. The study indicates that power supply by HVDC transmission from land to offshore oil installations could be technically feasible, even without the large synchronous compensators normally required. It has been shown that in a network only supplied by an inverter, variations of active and reactive loads have significant influence on both voltage and frequency. Particularly it should be noted that the frequency shows a positive sensitivity to increases in load. This could make the system intrinsically unstable in the case of a frequency dependent load such as motors. It was not a part of the study to optimize controllers, but even with simple controllers it was possible to keep the frequency within limits given by norms and regulations, but the voltages were dynamically outside the limits, though not very far. These voltage overswings take place in the first few instances after a disturbance, so it takes unrealistically fast controllers to handle them. They are partly due to the model, where the land based rectifier and the DC reactors are simulated by a constant current source, but partly they have to be handled by overdimensioning of the system. The simulations indicate that it should be technically possible to supply an oil platform with electrical power from land by means of HVDC transmission with small synchronous compensators. Whether this is financially feasible has not been investigated. Neither has it been considered whether the necessary equipment can actually be installed on an oil platform. Recently both ABB and Siemens have presented solutions for HVDC transmission in the lower and medium power range based on voltage source converters based on IGBTs. Fully controllable voltage source HVDC converters have properties that may be better suited than conventional line commutated current source thyristor inverters, to supply weak or passive networks, such as offshore oil installations, with electrical power. But they also have some disadvantages, and a complete technical and financial comparison must be performed in order to decide about any potential project.