Cross-linked polyethylene has higher upper use temperature than normal polyethylene and is used as an insulating material for electricity carrying cables and hot water pipes. The most common method of inducing crosslinks is by reaction with silanes. After incorporation of silanes into polyethylene and upon hydrolysis with ambient moisture or with hot water, Si-O-Si crosslinks are formed between the various linear polyethylene chains. Industrially, this reaction is performed routinely. However, the efficiency of this reaction with respect to the silane is low and control of product distribution is difficult. A precise fundamental understanding is necessary to be able to manipulate the reactions and thus, allow for the facile processing of the polymers. Hydrocarbon models of polymers - heptane, dodecane - are being used to study this reaction in the laboratory. For the reaction, vinyltrimethoxysilane is used as the grafting agent along with di-tert-butyl peroxide as the radical initiator. MALDI, a mass spectrometric technique is used for the analysis of the product distribution after work-up. Advanced NMR techniques (COSY, HSQC, DEPT, APT, HMBC) are being conducted on the grafted hydrocarbon compounds to gain an in-depth understanding of the mechanism and regiochemistry of the grafting reaction. Scalable and cost effective methods to capture CO2 are important to counterbalance some of the global impact of the combustion of fossil fuels on climate change. The main options available now include absorption, adsorption and membrane technology. Amines, especially monoethanolamine, have been the most commercialized technology. However, it is not without disadvantages. House et al have investigated the energy penalty involved in the post-combustion CO2 capture and storage from coal-fired power plants and found that 15-20% reduction in the overall electricity usage is necessary to offset the penalty from capturing and storing 80% of United States coal fleet's CO2 emssions1. Novel non-aqueous amine solvents, developed by the Eckert Liotta group, react with CO2 to form ionic liquids. The ionic liquids readily desorb CO2 upon heating, regenerating the reactive amines and this cycle can be carried out multiple times. An iterative procedure is being adopted to develop amine solvents for CO2 capture. Thermodynamic information like reversal temperature and boiling point of the solvents are collected; they are then used to formulate structure property relationships which allow for new molecules to be engineered. On reaction with CO2, there is a sharp increase in viscosity which is unfavorable from a processing standpoint. Many approaches to mitigate and control viscosity are being studied as well. 1House et al, Energy Environ Sci, 2009, 2, 193-205

M. Tech. Biomedical Technology. / Aims to gain more insights into the effect of a specific human derived BMP-complex, standardised according to the human BMP-2 content, by loading it at concentrations higher than the concentration of the morphogen found in human (hDBM), in order to determine changes in the osteogenic response.

Healing large bone defects remains a clinical challenge. While autografts are the gold standard treatment for large bone defects, they are limited by availability and donor site pain. Growth factor treatments such as BMP therapy provide a promising alternative but are expensive and present clinical safety concerns, primarily due to delivery of BMPs at supraphysiological doses. Integrins are ECM receptors which mediate crucial cell functions such as adhesion and differentiation. Therefore, understanding the role of integrins in bone formation and directing desired interactions may enable modulation of host cell functions for therapeutic applications. In this work, beta 1 integrins were deleted in osteolineage cells of transgenic mice at three different stages of differentiation to elucidate their role in bone development. We also engineered bioartificial PEG-based matrices which target the pro-osteogenic alpha 2 beta 1 integrin to promote bone healing. Conditional deletion of beta 1 integrins in osteochondroprogenitor cells under the Twist 2 promoter resulted in severe pre-natal skeletal mineralization defects and embryonic lethality. Targeted deletion of beta 1 integrins in osterix-expressing osteoprogenitors resulted in growth abnormalities, reduced calvarial mineralization, impaired femur development, and tooth defects. However, mice lacking beta 1 integrins in osteocalcin-expressing osteoblasts and osteocytes displayed only a mild skeletal phenotype, indicating that beta 1 integrins play an important role in early skeletal development, but are not required for mature osteoblast function. PEG hydrogels functionalized with the integrin-specific GFOGER ligand enhanced bone regeneration, induced defect bridging in combination with low doses of rhBMP-2 and stimulated improved bone healing compared collagen sponges, which are the clinical standard delivery vector for BMP-2 therapy. These results suggest that treatment with bioartificial integrin-specific PEG hydrogels may be a promising clinical strategy for bone regeneration in large bone defects.

Dental caries and periodontal disease are the major causes for tooth loss. While dental caries commonly involve the posterior teeth in both jaws, the teeth most commonly lost due to periodontal problems are the first and second molars in the maxilla. As a consequence, the upper posterior jaw is frequently edentulous. Implant therapy today is a predictable treatment modality for prosthetic reconstruction of edentulous patient. Insufficient amounts of bone, due to atrophy following loss of teeth or due to the presence of the maxillary sinus, can make it impossible to insert implants in the posterior maxilla. During the 1970s and 1980s, Tatum, Boyne and James and Wood and Moore first described maxillary sinus floor augmentation whereby, after the creation of a lateral access point, autologous bone grafts are inserted to increase crestal bone height and to create the necessary conditions for the insertion of implants. This surgical procedure requires a two-stage approach and a double surgical site: first, bone is harvested from a donor site and transplanted to the recipient site; then, after a proper healing period of between 4 to 6 months, the implants are inserted. This kind of bone reconstruction, even if well documented, has its limitations, not least in the creation of two different surgical sites and the consequent increased risk of morbidity. In 2004, Lundgren et al. described a new, simplified technique for the elevation of the sinus floor. The authors showed that by lifting the sinus membrane an empty space was created in which blood clot formations resulted in the establishment of new bone. The implants were placed simultaneously to function as “tent poles”, thus maintaining the sinus membrane in a raised position during the subsequent healing period. An essential prerequisite of this technique is to obtain optimal primary implant stability from the residual bone in the sinus floor. An extremely resorbed maxillary sinus floor, with, for example, less than 2-3 mm of poor quality residual bone, could impair implant insertion. The aims of the present research project were (i) to evaluate the donor site morbidity and the acceptance level of patients when a bone graft is harvested from the anterior iliac crest, (ii) to evaluate implant stability, new bone formation inside the maxillary sinus and marginal bone resorption around the implants in long term follow up when maxillary sinus floor augmentation is performed through sinus membrane elevation and without the addition of any grafting material, (iii) to investigate new bone formation inside the maxillary sinus, in experimental design, using a resorbable space-maker device in order to maintain elevation of the sinus membrane where there is too little bone to insert implants with good primary stability. In Paper I, 70 consecutively treated patients were retrospectively evaluated in terms of postoperative donor site morbidity and donor site complications. With regard to donor site morbidity, 74% of patients were free of pain within 3 weeks, whereas 26% had a prolonged period of pain lasting from a few weeks to several months. For 11% of patients there was still some pain or discomfort 2 years after the grafting surgery. Nevertheless, patients acceptance was high and treatment significantly improved oral function, facial appearance, and recreation/social activities and resulted in an overall improvement in the quality of life of formerly edentulous patients. In Paper I and III, some differently shaped space-making devices were tested on primates (tufted capuchin - Cebus apella) in two experimental models aimed at evaluating whether a two-stage procedure for sinus floor augmentation could benefit from the use of a space-making device to increase the bone volume and enable later implant installation with good primary stability, without the use of any grafting material. An histological examination of the specimens showed that it is possible to obtain bone formation in contact with both the Schneiderian membrane and the device. In most cases the device was displaced. The process of bone formation indicated that this technique is potentially useful for two-stage sinus floor augmentation. The lack of device stability within the sinus requires further improvement in space-makers if predictable bone augmentation is to be achieved. In Paper IV, a total of 84 patients were subjected to 96 membrane elevation procedures and the simultaneous placement of 239 implants. Changes of intra-sinus and marginal bone height in relation to the implants were measured in intraoral radiographs carried out during insertion after 6 months of healing, after 6 months of loading and then annually. Computerised tomography was performed pre-surgically and 6 months post-surgically. Resonance frequency analysis measurements were performed at the time of implant placement, at abutment connection and after 6 months of loading. The implant follow-up period ranged from a minimum of one to a maximum of 6 years after implant loading. All implants were stable after 6 months of healing. A total of three implants were lost during the follow-up period giving a survival rate of 98.7%. Radiography demonstrated an average of 5.3 ± 2.1 mm of intra-sinus new bone formation after 6 months of healing. RFA measurements showed adequate primary stability (implant stability quotient 67.4 ± 6.1) and small changes over time. In conclusion, harvesting bone from the iliac crest could result in temporary donor site morbidity, but in 11% of patients pain or discomfort was still present up to 2 years after surgery. However, patient satisfaction was good despite this slow or incomplete recovery, as showed by the quality of life questionnaire. Maxillary sinus membrane elevation without the use of bone grafts or bone substitutes results in predictable bone formation both in animal design, where the sinus membrane is supported by a resorbable device, and in clinical conditions, where the membrane is kept in the upper position by dental implants. This new bone formation is accompanied by a high implant survival rate of 98.7% over a follow-up period of up to 6 years. Intra-sinus bone formation remained stable in the long-term follow-up. It is suggested that the secluded compartment allowed bone formation in accordance with the principle of guided tissue regeneration. This technique reduces the risks of morbidity related to bone graft harvesting and eliminates the costs of grafting materials.

Cellulose is one of the most abundant biopolymers found in nature. Cellulose based derivatives have a number of advantages including recyclability, reproducibility, biocompatibility, biodegradability, cost effectiveness and availability in a wide variety of forms. Due to the benefits of cellulose based systems, this research study was aimed at developing novel cellulosic nanoparticles with potential pharmaceutical and personal care applications. Two different cellulosic systems were evaluated, each with its own benefits and proposed applications. The first project involves the synthesis and characterization of polyampholyte nanoparticles composed of chitosan and carboxymethyl cellulose (CMC), a cellulosic ether. EDC carbodiimide chemistry and inverse microemulsion technique was used to produce crosslinked nanoparticles. Chitosan and carboxymethyl cellulose provide amine and carboxylic acid functionality to the nanoparticles thereby making them pH responsive. Chitosan and carboxymethyl cellulose also make the nanoparticles biodegradable and biocompatible, making them suitable candidates for pharmaceutical applications. The synthesis was then extended to chitosan and modified methyl cellulose microgel system. The prime reason for using methyl cellulose was to introduce thermo-responsive characteristics to the microgel system. Methyl cellulose was modified by carboxymethylation to introduce carboxylic acid functionality, and the chitosan-modified methyl cellulose microgel system was found to be pH as well as temperature responsive. Several techniques were used to characterize the two microgel systems, for e.g. potentiometric and conductometric titrations, dynamic light scattering and zeta potential measurements. FTIR along with potentiometric and conductometric titration was used to confirm the carboxymethylation of methyl cellulose. For both systems, polyampholytic behaviour was observed in a pH range of 4-9. The microgels showed swelling at low and high pH values and deswelling at isoelectric point (IEP). Zeta potential values confirmed the presence of positive charges on the microgel at low pH, negative charges at high pH and neutral charge at the IEP. For chitosan-modified methyl cellulose microgel system, temperature dependent behaviour was observed with dynamic light scattering. The second research project involved the study of binding interaction between nanocrystalline cellulose (NCC) and an oppositely charged surfactant tetradecyl trimethyl ammonium bromide (TTAB). NCC is a crystalline form of cellulose obtained from natural sources like wood, cotton or animal sources. These rodlike nanocrystals prepared by acid hydrolysis of native cellulose possess negatively charged surface. The interaction between negatively charged NCC and cationic TTAB surfactant was examined and it was observed that in the presence of TTAB, aqueous suspensions of NCC became unstable and phase separated. A study of this kind is imperative since NCC suspensions are proposed to be used in personal care applications (such as shampoos and conditioners) which also consist of surfactant formulations. Therefore, NCC suspensions would not be useful for applications that employ an oppositely charged surfactant. In order to prevent destabilization, poly (ethylene glycol) methacrylate (PEGMA) chains were grafted on the NCC surface to prevent the phase separation in presence of a cationic surfactant. Grafting was carried out using the free radical approach. The NCC-TTAB polymer surfactant interactions were studied via isothermal titration calorimetry (ITC), surface tensiometry, conductivity measurements, phase separation and zeta potential measurements. The major forces involve in these systems are electrostatic and hydrophobic interactions. ITC and surface tension results confirmed two kinds of interactions: (i) electrostatically driven NCC-TTAB complexes formed in the bulk and at the interface and (ii) hydrophobically driven TTAB micellization on the NCC rods. Conductivity and surface tension results confirmed that the critical micelle concentration of TTAB (CMCTTAB) shifted to higher values in the presence of NCC. Phase separation measurements allowed us to identify the formation of large aggregates or hydrophobic flocs depending on the TTAB concentration. Formation of NCC-TTAB complexes in aqueous solutions was confirmed by a charge reversal from negative to positive charge on the NCC rods. The effect of electrolyte in shielding the negative charges on the NCC was observed from ITC, surface tensiometry and phase separation experiments. Several mechanisms have been proposed to explain the above results. Grafting of PEGMA on the NCC surface was confirmed using FTIR and ITC experiments. In phase separation experiments NCC-g-PEGMA samples showed greater stability in the presence of TTAB compared to unmodified NCC. By comparing ITC and phase separation results, an optimum grafting ratio (PEGMA : NCC) for steric stabilization was also proposed.

Ordered mesoporous silicas have been shown to have a variety of useful applications ranging from adsorbents for containments to supports for catalysts. While these materials have received a good deal of attention in the literature there is still much opportunity for new technologies. We present research describing a novel approach to incorporate functionality onto the pore surfaces of these materials as well as a highly active catalyst for the Suzuki-Miyaura reaction. Our approach to selectively graft functionality on to the pore walls of the mesoporous silicas SBA-15 and MCM-41 involves treating the materials loaded with a structure directing agent (SDA), with hexamethyldisilazane that passivates the external surface through silylation. Once the SDA is removed the mesopores can be functionalized selectively using standard methods. A test designed to look at the passivation layer is also described. The catalyst developed is designated Pd-SBA-15-SH(g) and it is active for the Suzuki-Miyaura reaction. The activity, recyclability and leaching of Pd-SBA-15-SH(g) was found to be superior to related materials. A mechanistic analysis suggests the catalyst is a reservoir for soluble Pd metal. A key challenge that is holding back wide scale application of ammonia borane (NH3BH3) as a hydrogen storage material for mobile applications is the dearth of regeneration strategies. Presented are our forays into the development of an organic hydride based regeneration strategy. The first phase of the project focused on the reaction between Hantzsch esters and B(C6F5)3. N-substituted Hantzsch esters were found to transfer hydride to boron in >90 % yield. Mechanistic analysis of the reaction suggests either a SET mechanism or a highly asynchronous transition state. A novel hydride transfer equilibrium promoted by B(C6F5)3 was observed and it operated at temperatures below -10 ºC. N,N-ditertbutyl-dihydroimidazole is also an effective hydride donor to B(C6F5)3 as well as other Lewis acids that are more relevant mimics to those invoked in regeneration schemes. When the redistribution of B(SPh)3 is carried out with N,N-ditertbutyl-dihydroimidazole in the presence of NEt3 and CH2Cl2 at 50 ºC, BH2(NEt)3(SPh) is formed. CH2Cl2 functions as a thiol scavenger under the reaction conditions. 1-Octene trapping experiments provided indirect evidence for the formation of diborane, a critical component in the regeneration of NH3BH3. / Thesis (Ph.D, Chemistry) -- Queen's University, 2011-09-09 14:51:54.697

Protein PEGylation (covalent attachment of poly(ethylene glycol) or PEG to proteins) is an excellent example of a drug delivery system that improves pharmacokinetics and pharmacodynamic properties of therapeutics. However, although PEGylation is clinically proven and attracts both scientific and commercial interest, the technique is associated with many process constraints, in particular related to controlling the number of conjugated PEG chains. A novel, solid-phase PEGylation methodology was attempted to overcome the drawbacks of the commonly used solution-phase methods for preparing PEGylated products. The solid-phase PEGylation methodology involved conjugating protein onto a tethered PEG derivative attached onto a solid matrix, followed by hydrolytic cleavage of the PEG chain from the solid matrix under mild conditions to yield PEGylated protein in free solution. PEGs with molecular weights (MWs) 2000 and 4000 Da were used and a heterobifunctional PEG derivative, α-(β-alanine)-ω-carboxy PEG, with a cleavable β-alanine ester terminal was prepared for surface grafting and protein conjugation. The amine terminal of this PEG derivative was used for grafting PEG onto carboxy functionalized hydrophilic Sephadex and hydrophobic polystyrene derivatives. The free carboxyl terminal was used for protein conjugation via amine coupling. A kinetic study of PEG-surface grafting was performed to understand the influence of a number of parameters on the PEG surface concentration and its conformation, including temperature, reaction time, nature of the matrix, solvent and base, and MW of PEG. PEG grafted matrices were characterized using various surface characterization tools including Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). Higher PEG grafting was observed with polystyrene matrices (up to 0.3 mmol/g) than either of the Sephadex derivatives (less than 0.15 mmol/g) using both molecular weights. Detailed surface characterization using XPS studies showed a layer thickness of 11.87 nm was achieved with polystyrene matrices using 4000 Da PEG derivatives after a grafting period of 72 hours at 40°C, indicating the presence of brush conformations for the grafted PEGs. In contrast, mushroom conformations were observed for PEG molecules grafted on both carboxymethyl and carboxypentyl Sephadex derivatives after the same reaction period, with a layer thickness of 2.62 nm and 4.14 nm respectively. Optimized PEG grafting and hydrolysis conditions were developed for solid-phase protein PEGylation using Cytochrome c as a model protein. The presence of PEGylated species were detected by size exclusion chromatography (SEC) from Sephadex derivatives but were absent when using polystyrene matrices. Both Sephadex derivatives gave mainly multi-PEGylated species with poor yields, in place of the expected mono-PEGylated products. A solution-phase PEGylation using the same PEG derivatives was performed successfully and various PEGylated species were identified and characterized using SEC and gel electrophoresis, based on their viscosity radius. An examination of the surface characteristics of the PEG-grafted was carried out by XPS, showing that protein conjugation was greatly influenced by surface force interactions, which depended on the PEG grafting densities and the nature of the solid matrices. Finally, fluorescent images obtained using confocal microscope with fluorescein isothiocyanate labelled Cytochrome c provided supporting evidence regarding the factors that constrained the solid-phase PEGylation process.

Disertacijos tikslas buvo sukurti metodą periodinių darinių formavimui interferencinės litografijos būdu, polimerizuojant fotojautrias medžiagas, eksperimentiškai ištirti šio metodo galimybes ir ribojimus bei suformuoti mikrodarinius, tinkamus praktiniams taikymams. Eksperimentų metu buvo pademonstruota, kad interferencinės litografijos metodu formuojamų mikrodarinių forma priklauso nuo: lazerinės apšvitos dozės, bangos ilgio, fazės, kampo tarp interferuojančių pluoštų ir pluoštų skaičiaus, o jų tvirtumas labiausiai priklauso nuo lazerinės apšvitos dozės. Šiame darbe taip pat parodyta, kad naudojant interferencinės litografijos metodą viena lazerine ekspozicija galima formuoti mikrovamzdelių ir mikrolęšių masyvus bei karkasus iš biosuderinamos ir biosuskaidomos PEG-DA-258 medžiagos. Be polimerinių darinių formavimo, šiame darbe pademonstruota ir jų fotomodifikavimo galimybė, naudojant fotoįskiepijimo (angl. photo-grafting) technologiją, o taip pat realizuojant variu katalizuojamos azido alkino ciklizacijos (CuAAC) cheminę reakciją parodyta fotoįskiepijimo technologijos ir „klik“ chemijos apjungimo galimybė. Toks paprastas ir universalus būdas atveria naujas galimybes biojutiklių kūrime ir audinių inžinerijoje, nes molekulių imobilizavimas polimero matricoje vyksta trimatėje erdvėje ir tiksliai norimoje vietoje, o trimatė erdvinė gradientinė kontrolė yra labai svarbi daugybėje biotechnologijos taikymų. / The main aim of this work was to develop the formation technique of periodic micro-structures by interference lithography in photosensitive polymeric materials, experimentally investigate possibilities and limitations of the method, and to create micro-structures suitable for practical applications. The shape of the micro-structures fabricated by interference lithography depends on the used laser irradiation dose, laser wavelength, phase, polarization, the angle between interfering beams and the number of the interfering beams, and their rigidity - mainly on the used laser irradiation dose. In this work also the possibility to form micro-tube and scaffolds arrays by using interference lithography was demonstrated and the control of the geometrical parameters of micro-lenses fabricated by interference lithography and manipulating the laser irradiation dose was investigated in depth. The possibility to immobilize the newly synthesized aromatic azides molecules in PEG matrix by photo-grafting technique was also demonstrated and the copper(I)-catalyzed azide–alkyne cycloaddition (CuAAC) chemical reaction by using azide “MegaStokes dye 673” was realized, in order to show the capability to combine the photo-grafting technique with “click” chemistry. The developed 3D site-specific functionalization method is simple and versatile; it has potential applications in micro-array based proteome analysis, studies of cell-surface interactions, sensing applications, and drug screening.

The main aim of this work was to develop the formation technique of periodic micro-structures by interference lithography in photosensitive polymeric materials, experimentally investigate possibilities and limitations of the method, and to create micro-structures suitable for practical applications. The shape of the micro-structures fabricated by interference lithography depends on the used laser irradiation dose, laser wavelength, phase, polarization, the angle between interfering beams and the number of the interfering beams, and their rigidity - mainly on the used laser irradiation dose. In this work also the possibility to form micro-tube and scaffolds arrays by using interference lithography was demonstrated and the control of the geometrical parameters of micro-lenses fabricated by interference lithography and manipulating the laser irradiation dose was investigated in depth. The possibility to immobilize the newly synthesized aromatic azides molecules in PEG matrix by photo-grafting technique was also demonstrated and the copper(I)-catalyzed azide–alkyne cycloaddition (CuAAC) chemical reaction by using azide “MegaStokes dye 673” was realized, in order to show the capability to combine the photo-grafting technique with “click” chemistry. The developed 3D site-specific functionalization method is simple and versatile; it has potential applications in micro-array based proteome analysis, studies of cell-surface interactions, sensing applications, and drug screening. / Disertacijos tikslas buvo sukurti metodą periodinių darinių formavimui interferencinės litografijos būdu, polimerizuojant fotojautrias medžiagas, eksperimentiškai ištirti šio metodo galimybes ir ribojimus bei suformuoti mikrodarinius, tinkamus praktiniams taikymams. Eksperimentų metu buvo pademonstruota, kad interferencinės litografijos metodu formuojamų mikrodarinių forma priklauso nuo: lazerinės apšvitos dozės, bangos ilgio, fazės, kampo tarp interferuojančių pluoštų ir pluoštų skaičiaus, o jų tvirtumas labiausiai priklauso nuo lazerinės apšvitos dozės. Šiame darbe taip pat parodyta, kad naudojant interferencinės litografijos metodą viena lazerine ekspozicija galima formuoti mikrovamzdelių ir mikrolęšių masyvus bei karkasus iš biosuderinamos ir biosuskaidomos PEG-DA-258 medžiagos. Be polimerinių darinių formavimo, šiame darbe pademonstruota ir jų fotomodifikavimo galimybė, naudojant fotoįskiepijimo (angl. photo-grafting) technologiją, o taip pat realizuojant variu katalizuojamos azido alkino ciklizacijos (CuAAC) cheminę reakciją parodyta fotoįskiepijimo technologijos ir „klik“ chemijos apjungimo galimybė. Toks paprastas ir universalus būdas atveria naujas galimybes biojutiklių kūrime ir audinių inžinerijoje, nes molekulių imobilizavimas polimero matricoje vyksta trimatėje erdvėje ir tiksliai norimoje vietoje, o trimatė erdvinė gradientinė kontrolė yra labai svarbi daugybėje biotechnologijos taikymų.

This study covers grafting of Acrylic Acid (AA) and Methacrylic Acid (MAA) on Ultrahigh Molecular Weight Polyethylene (UHMWPE) thin films by surface grafting and xylene-swollen grafting methods with Co-60 &amp / #947 / -ray in air. Also characterizations of pure, irradiated and grafted films were made by applying gravimetric, spectroscopic, thermal and mechanic tests. The thin films of UHMWPE were prepared by using compression molding. AA and MAA grafting on thin UHMWPE films were carried out by surface grafting and xylene-swollen grafting methods. During grafting processes, homopolymerization of monomers was avoided by using Fe2+ and Cu2+ ions. Grafting degree of AA and MAA were calculated for the samples irradiated at different doses. To verify grafting of AA and MAA on UHMWPE films, FTIR spectra of grafted films were used. Metal-uptake capacity is important property of grafted polyethylene for environmental applications. Thus, we examined metal-uptake capacities of AA and MAA grafted films for Fe(III) and Ni (II) and it was found that AA and MAA grafted UHMWPE films showed good affinity towards Fe(III) and Ni(II) metals. Thermal behavior of films were examined by DSC analysis. First run and second run DSC thermograms showed the thermal stability of films under heat. Mechanical properties of UHMWPE decrease with irradiation and grafting. However stress at break values of xylene-swollen grafted samples tend to increase with irradiation dose. In conclusion, water soluble monomers were successfully grafted on UHMWPE and these AA and MAA grafted UHMWPE films can be used in biomedical, environmental applications and other related areas.