This thesis describes research on near degenerate quasi phase-matched opticalparametric oscillators (OPO) where volume Bragg gratings (VBG) are used toproduce narrow oscillation bandwidth. These OPOs are then used to pump a secondOPO to generate mid-infrared radiation. The atmospheric transmission windows in the 3.5 to 5 μm wavelength region areused for seekers on infrared homing missiles. These missiles are available to guerrillaand terrorist groups and have been used in a number of attacks on military and civilianaircraft. Laser sources at the same wavelengths are an important component incountermeasure systems for aircraft self-protection. Similar laser sources also haveapplications in laser surgery. At wavelengths longer than 4 μm crystal materials for multi-Watt level averagepower nonlinear devices is a problem. The best solution so far is to use ZnGeP2(ZGP). ZGP and the available alternatives all have a problem of near-infraredabsorption, and a mid-infrared OPO thus has to use a pump wavelength near 2 μm.This pump source can be a neodymium laser at 1.06 μm with a near degenerate OPO. Nonlinear devices for low to medium pulse energies are dominated by quasi phasematchedmaterials because of their higher effective nonlinearities and lack of walkoff.In addition they allow type I interaction where signal and idler from the OPOhave the same polarization, which has the advantage that both waves can be used topump the ZGP OPO. The drawback of this is that the near-degenerate interaction hasvery wide gain bandwidth. Efficient pumping of the second OPO demands narrowbandwidth output from the first OPO.Volume Bragg gratings that are glass materials with a periodic refractive indexmodulation have emerged as high quality narrow bandwidth reflectors. By using aVBG as one cavity mirror in an OPO the feedback bandwidth and hence the OPOoscillation bandwidth can be kept very narrow. Signal and idler bandwidths of 10 and20 GHz (FWHM) at 2122 and 2135 nm, respectively, have been demonstrated. Thisshould be compared to the several hundred nanometre bandwidth from an OPO usingdielectric mirrors. Very narrow bandwidth operation has been achieved so close todegeneracy that the signal and idler are not resolvable. The total output energy generated in the PPKTP OPO (signal and idler together)has been used to pump a ZGP OPO that produced mid-IR radiation. Tuning of thesignal from a ZGP OPO from 2.9 μm to degeneracy at 4.3 μm has been shown, with acorresponding idler wavelength tuneable up to 8 μm. The highest conversionefficiency that has been reached from 1.06 μm to the mid-IR was 12 %. This setupused a PPKTP OPO with 30 % conversion efficiency and 13 nm separation of signaland idler (2122 and 2135 nm). The pulse repetition frequency was 20 kHz and thegenerated output power in the mid-IR was 3.2 W. / QC 20100517

The primary objective of the presented research is to develop a class of integrated compact silicon diffractive sensors (CSDS) based on in-plane diffraction gratings. This class of sensors uses a silicon-on-insulator (SOI) substrate to limit costs, exploit established fabrication processes, enable integration of supporting electronics, and use the well-understood telecommunications wavelength of 1.55µm. Sensing is achieved by combining constant-diffraction-efficiency and highly-angularly-selective in-plane resonance-domain diffraction gratings. Detection is based on the diffraction efficiency of the highly angularly selective grating. In this research, the design processes for the constant-diffraction-efficiency and the highly angularly selective gratings are detailed. Grating designs are optimized with rigorous coupled-wave analysis (RCWA) and simulated with finite-difference time-domain (FDTD) analysis. Fabrication results are presented for the CSDS gratings. An inductively coupled plasma (ICP) Bosch etch process enables grating fabrication to within one percent of designed values with nearly vertical sidewalls. Experimental results are presented for individual CSDS gratings, the prototype sensor, and a prototype linear sensor array. The results agree well with simulation. The linear sensor array prototype demonstrates the intrinsic splitting mechanism and forms the basis of a 2-D sensor array. Finally, a toluene sensor was functionally demonstrated. The proof-of-concept device includes a polymer immobilization layer and microfluidic delivery of toluene. Toluene concentrations as low as 100ppm are measured, corresponding to a refractive index change of 3x10⁻⁴ RIU.

Fiber Bragg gratings (FBGs) are key elements in modern telecommunication and sensing applications. In optical communication, with the advancement of the Erbium doped fiber amplifier (EDFA), there is a great demand for devices with wavelength tunability over the Erbium gain bandwidth (in particular, for wavelength division multiplexing (WDM) networks). The center wavelength of a FBG can be shifted by means of change of temperature, pressure or mechanical axial strain. The axial strain approach is the best method among all other techniques because it allows relatively large wavelength shifts with high speed. Axial strain of up to 4% will be required to cover the whole EDFA region (more than 40 nm of central wavelength shift). The formation of Bragg grating results in significant reduction in mechanical strength of optical fibers especially in tension. As a result, axial strain of only about 1% can be achieved by mechanical stretching of FBGs. In order to achieve the remaining 3% strain compression of FBGs has to be applied. In this thesis, the design and analysis of a novel device for achieving central wavelength shift are presented. In particular, the device has achieved, for a fiber with 12 mm FBG, a shifting of 46 nm in compression and 10.5 nm in tension with a reflection power loss of less than 0.25 dB and a FWHM bandwidth variation of approximately 0.1 nm. Both variations are well below the Bellcore standards requirement of 0.5 dB for peak reflectivity variation and 0.1 nm for bandwidth variation. The device consists of two fixed and one guiding ferrules. The difficulties associated with compressing the FBG were handled by carefully selecting tolerances and adjustment procedures. The device allows both tension and compression of FBGs, and the use of different FBG lengths and actuators. The effects of glue deformation and bending of the FBG during compression were analyzed in detail. Further, using the piezoelectric transducer (PZT) actuator as a driver, tuning speed of around 1.5nm/ms was achieved.

The focus of this thesis is on the development of sensing devices based on optical fiber sensors, specifically optical Fiber Bragg Gratings (FBG), using laser microfabrication methods. FBG is a type of optical fibers whose spectral response is affected by applied strain and temperature. As a result, it can be calibrated for the measurement of physical parameters manifesting themselves in the changes of strain or temperature. The unique features of optical fiber sensors such as FBGs have encouraged the widespread use of the sensor and the development of optical fiber-based sensing devices for structural measurements, failure diagnostics, thermal measurements, pressure monitoring, etc. These features include light weight, small size, long-term durability, robustness to electromagnetic disturbances, and resistance to corrosion. Despite the encouraging features, there are some limitations and challenges associated with FBGs and their applications. One of the challenges associated with FBGs is the coupling of the effects of strain and temperature in the optical response of the sensors which affects the reliability and accuracy of the measurements. Another limitation of FBGs is insensitivity to the index of refraction of their surrounding medium. In liquids, the index of refraction is a function of concentration. Making FBGs sensitive to the index of refraction and keeping their thermal sensitivity intact enable optical sensors with the capability of the simultaneous measurement of concentration and temperature in liquids. Considering the unique features of FBGs, embedding of the sensors in metal parts for in-situ load monitoring is a cutting-edge research topic. Several industries such as machining tools, aerospace, and automotive industries can benefit from this technology. The metal embedding process is a challenging task, as the thermal decay of UV-written gratings can starts at a temperature of ~200 oC and accelerates at higher temperatures. As a result, the embedding process needs to be performed at low temperatures. The objective of the current thesis is to move forward the existing research front in the area of optical fiber sensors by finding effective solutions to the aforementioned limitations. The approaches consist of modeling, design, and fabrication of new FBG-based sensing devices. State-of-the-art laser microfabrication methods are proposed and implemented for the fabrication of the devices. Two approaches are adopted for the development of the FBG-based sensing devices: the additive method and the subtractive method. In both methods, laser direct microfabrication techniques are utilized. The additive method deals with the deposition of on-fiber metal thin films, and the subtractive method is based on the selective removal of materials from the periphery of optical fibers. To design the sensing devices and analyze the performance of the sensors, an opto-mechanical model of FBGs for thermal and structural monitoring is developed. The model is derived from the photo-elastic and thermo-optic properties of optical fibers. The developed model can be applied to predict the optical responses of a FBG exposed to structural loads and temperature variations with uniform and non-uniform distributions. The model is also extended to obtain optical responses of superstructure FBGs in which a secondary periodicity is induced in the index of refraction along the optical fiber. To address the temperature-strain coupling in FBGs, Superstructure FBGs (SFBG) with on-fiber metal thin films are designed and fabricated. It is shown that SFBGs have the capability of measuring strain and temperature simultaneously. The design of the sensor with on-fiber thin films is carried out by using the developed opto-mechanical model of FBGs. The performance of the sensor in concurrent measurement of strain and temperature is investigated by using a customized test rig. A laser-based Direct Write (DW) method, called Laser-Assisted Maskless Microdeposition (LAMM), is implemented to selectively deposit silver thin films on optical fibers and fabricate the superstructure FBGs. To attain thin films with premium quality, a characterization scheme is designed to study the geometrical, mechanical, and microstructural properties of the thin films in terms of the LAMM process parameters. A FBG, capable of measuring concentration and temperature of liquids is developed, and its performance is tested. Femtosecond laser micromachining is successfully implemented as a subtractive method for the sensor fabrication. For this purpose, periodic micro-grooves are inscribed in the cladding of regular FBGs so as to increase their sensitivity to the concentration of their surrounding liquid while keeping their thermal sensitivity intact. This type of sensors has the potential for applications in biomedical research, in which the in-situ measurement of the properties of biological analytes is required. Another accomplishment of this thesis is the development of FBG sensors embedded in metal parts for structural health monitoring using low temperature embedding processes. In this regard, the opto-mechanical model is extended to predict the optical response of the embedded FBGs. The embedding process involves low temperature casting, on-fiber thin film deposition, and electroplating methods. The performance of the embedded sensors is evaluated in structural loading and thermal cycling.

The aim of this master's thesis is to develop a method that fully automates a trimming step in the production of a fiber-optical power spectrometer, based on a unique Acusto-Optical Scanning Filter. The filter is created by letting an ultrasonic mechanical pulse pass through a chirped Fiber Bragg Grating. The pulse introduces a disturbance in the grating, creating a thin optical transmission window in the otherwise reflective bandwidth. The high demands on the window requires a precise, unit dependent pulse form with unknown properties. Thus each unit needs to be trimmed to reach required performance. The manual trimming is largely a trial and error process, that contains two performance tests. We redefine one, eliminating the need to reroute the optical path and reducing the number of fiber weldings. The tests are then quantified, allowing a figure of merit to be based on weighted performance values. A brute force method, testing a large set of pulses, is implemented. The set is defined by the parameter space spanned by previously produced units. Due to the large space, the method is too time consuming. Instead it is used to measure the performance spaces of three units. An attempt to largely reduce the parameter space using PCA failed. An alternating variables method that finds local performance optima in the parameter space is developed. By using a set of several starting points, the method tends to find several qualified pulses. The method is implemented and successfully verified by trimming new units. Finally we propose where to focus improvements of the method in a production ramp up.

The focus of this thesis is on the development of sensing devices based on optical fiber sensors, specifically optical Fiber Bragg Gratings (FBG), using laser microfabrication methods. FBG is a type of optical fibers whose spectral response is affected by applied strain and temperature. As a result, it can be calibrated for the measurement of physical parameters manifesting themselves in the changes of strain or temperature. The unique features of optical fiber sensors such as FBGs have encouraged the widespread use of the sensor and the development of optical fiber-based sensing devices for structural measurements, failure diagnostics, thermal measurements, pressure monitoring, etc. These features include light weight, small size, long-term durability, robustness to electromagnetic disturbances, and resistance to corrosion. Despite the encouraging features, there are some limitations and challenges associated with FBGs and their applications. One of the challenges associated with FBGs is the coupling of the effects of strain and temperature in the optical response of the sensors which affects the reliability and accuracy of the measurements. Another limitation of FBGs is insensitivity to the index of refraction of their surrounding medium. In liquids, the index of refraction is a function of concentration. Making FBGs sensitive to the index of refraction and keeping their thermal sensitivity intact enable optical sensors with the capability of the simultaneous measurement of concentration and temperature in liquids. Considering the unique features of FBGs, embedding of the sensors in metal parts for in-situ load monitoring is a cutting-edge research topic. Several industries such as machining tools, aerospace, and automotive industries can benefit from this technology. The metal embedding process is a challenging task, as the thermal decay of UV-written gratings can starts at a temperature of ~200 oC and accelerates at higher temperatures. As a result, the embedding process needs to be performed at low temperatures. The objective of the current thesis is to move forward the existing research front in the area of optical fiber sensors by finding effective solutions to the aforementioned limitations. The approaches consist of modeling, design, and fabrication of new FBG-based sensing devices. State-of-the-art laser microfabrication methods are proposed and implemented for the fabrication of the devices. Two approaches are adopted for the development of the FBG-based sensing devices: the additive method and the subtractive method. In both methods, laser direct microfabrication techniques are utilized. The additive method deals with the deposition of on-fiber metal thin films, and the subtractive method is based on the selective removal of materials from the periphery of optical fibers. To design the sensing devices and analyze the performance of the sensors, an opto-mechanical model of FBGs for thermal and structural monitoring is developed. The model is derived from the photo-elastic and thermo-optic properties of optical fibers. The developed model can be applied to predict the optical responses of a FBG exposed to structural loads and temperature variations with uniform and non-uniform distributions. The model is also extended to obtain optical responses of superstructure FBGs in which a secondary periodicity is induced in the index of refraction along the optical fiber. To address the temperature-strain coupling in FBGs, Superstructure FBGs (SFBG) with on-fiber metal thin films are designed and fabricated. It is shown that SFBGs have the capability of measuring strain and temperature simultaneously. The design of the sensor with on-fiber thin films is carried out by using the developed opto-mechanical model of FBGs. The performance of the sensor in concurrent measurement of strain and temperature is investigated by using a customized test rig. A laser-based Direct Write (DW) method, called Laser-Assisted Maskless Microdeposition (LAMM), is implemented to selectively deposit silver thin films on optical fibers and fabricate the superstructure FBGs. To attain thin films with premium quality, a characterization scheme is designed to study the geometrical, mechanical, and microstructural properties of the thin films in terms of the LAMM process parameters. A FBG, capable of measuring concentration and temperature of liquids is developed, and its performance is tested. Femtosecond laser micromachining is successfully implemented as a subtractive method for the sensor fabrication. For this purpose, periodic micro-grooves are inscribed in the cladding of regular FBGs so as to increase their sensitivity to the concentration of their surrounding liquid while keeping their thermal sensitivity intact. This type of sensors has the potential for applications in biomedical research, in which the in-situ measurement of the properties of biological analytes is required. Another accomplishment of this thesis is the development of FBG sensors embedded in metal parts for structural health monitoring using low temperature embedding processes. In this regard, the opto-mechanical model is extended to predict the optical response of the embedded FBGs. The embedding process involves low temperature casting, on-fiber thin film deposition, and electroplating methods. The performance of the embedded sensors is evaluated in structural loading and thermal cycling.

Fiber Bragg gratings (FBGs) are key elements in modern telecommunication and sensing applications. In optical communication, with the advancement of the Erbium doped fiber amplifier (EDFA), there is a great demand for devices with wavelength tunability over the Erbium gain bandwidth (in particular, for wavelength division multiplexing (WDM) networks). The center wavelength of a FBG can be shifted by means of change of temperature, pressure or mechanical axial strain. The axial strain approach is the best method among all other techniques because it allows relatively large wavelength shifts with high speed. Axial strain of up to 4% will be required to cover the whole EDFA region (more than 40 nm of central wavelength shift). The formation of Bragg grating results in significant reduction in mechanical strength of optical fibers especially in tension. As a result, axial strain of only about 1% can be achieved by mechanical stretching of FBGs. In order to achieve the remaining 3% strain compression of FBGs has to be applied. In this thesis, the design and analysis of a novel device for achieving central wavelength shift are presented. In particular, the device has achieved, for a fiber with 12 mm FBG, a shifting of 46 nm in compression and 10.5 nm in tension with a reflection power loss of less than 0.25 dB and a FWHM bandwidth variation of approximately 0.1 nm. Both variations are well below the Bellcore standards requirement of 0.5 dB for peak reflectivity variation and 0.1 nm for bandwidth variation. The device consists of two fixed and one guiding ferrules. The difficulties associated with compressing the FBG were handled by carefully selecting tolerances and adjustment procedures. The device allows both tension and compression of FBGs, and the use of different FBG lengths and actuators. The effects of glue deformation and bending of the FBG during compression were analyzed in detail. Further, using the piezoelectric transducer (PZT) actuator as a driver, tuning speed of around 1.5nm/ms was achieved.

Optical interconnects are important to the future development of microelectronics. Volume grating couplers (VGCs) provide a compact, efficient coupling mechanism that is compatible with microelectronics fabrication processes. In this dissertation, some of the performance characteristics of VGCs are investigated. Also, integration of VGCs with Sea of Polymer Pillars (SoPP), an emerging high-density input/output interconnect technology, is demonstrated and its performance quantitatively investigated. First, the polarization-dependent performance of VGCs is analyzed, and the design constraints for achieving high-efficiency polarization-dependent and polarization-independent VGCs are examined. The effects of loss on VGC performance are also presented. Then, the wavelength response of VGCs and its dependence on grating parameters is quantitatively examined. Experimental demonstrations of polarization-dependent and polarization-independent VGCs are then presented. Finally, a VGC integrated with a SoPP is demonstrated and its performance characterized.

This dissertation introduces new technologies and techniques for low-cost phased arrays and scanning antennas. Special emphasis is placed on new approaches for low-cost millimeter-wave beam control. Several topics are covered. A novel reconfigurable grating antenna is presented for low-cost millimeter-wave beam steering. The versatility of the approach is proven by adapting the design to dual-beam and circular-polarized operation. In addition, a simple and accurate procedure is developed for analyzing these antennas. Designs are presented for low-cost microwave/millimeter-wave phased-array transceivers with extremely broad bandwidth. The target applications for these systems are mobile satellite communications and ultra-wideband radar. Monolithic PIN diodes are a useful technology, especially suited for building miniaturized control components in microwave and millimeter-wave phased arrays. This dissertation demonstrates a new strategy for extracting bias-dependent small-signal models for monolithic PIN diodes. The space solar-power satellite (SPS) is a visionary plan that involves beaming electrical power from outer space to the earth using a high-power microwave beam. Such a system must have retrodirective control so that the high-power beam always points on target. This dissertation presents a new phased-array architecture for the SPS system that could considerably reduce its overall cost and complexity. In short, this dissertation presents technologies and techniques that reduce the cost of beam steering at microwave and millimeter-wave frequencies. The results of this work should have a far-ranging impact on the future of wireless systems.

In this thesis, a 6-beam combiner using multiplexed holograms in dye-doped polymer is investigated. It is realized by recording six superimposed holographic gratings, which show uniform diffraction efficiency. The coupled wave theory for N superimposed gratings is more generalized and is used to analyze the amplitudes of diffracted waves in three different boundary conditions. Multiple-ring diffracted beam analysis is proposed to determine the dynamic range of a holographic material. The M/# is evaluated by recording a single hologram and counting the number of ring patterns in the diffracted beam. This analysis is extended to assess the equalized grating strength of N superimposed holograms. Six holograms with the equalized grating strength which can be assigned within the dynamic range of our material and show maximum diffraction efficiency are recorded. The phase locking of five beams to one reference beam is performed using PZT controller. The designs of lock-in amplifier, ramp generator and servo using commercial chips are demonstrated. The readout set-up used to split one single beam into six coherent copies is presented. The function of each part of the PZT controller in the readout set-up is discussed in detail. The intensity profile of an N-beam combiner is investigated by varying the phase angle between adjacent input waves. The entire solution which describes the amplitude of a combined beam is derived from generalized coupled wave theory. A simplified experimental set-up without a complicated PZT controller is demonstrated using a planoconvex lens. In order to provide six coherent light sources in future work, the injection locking of a single laser diode to the master laser diode is performed. An expected read-out setup is proposed to carry out both the achievement of six coherent sources and a 6 beam combination.