The main topic of this thesis work is photosensitivity and photo-structuring of optical fibers and bulk glass. Although research in the field of photosensitivity in glass and optical fibers has been ongoing for more than three decades, the underlying mechanisms are still not well understood. The objective was to gain a better understanding of the photo-response by studying photosensitivity from a thermodynamic perspective, as opposed to established research focusing on point defects and structural changes, and strain and stress in optical fibers. Optical fibers was mainly used for experimental studies for two reasons; first, photosensitivity in fibers is more pronounced and more elusive compared to its bulk counterpart, and secondly, fibers provide a simplified structure to study as they experimentally can be seen as one-dimensional.Initially, ablation experiments on bulk glass were performed using picosecond infrared pulses. With a design cross section of 40x40 μm, straight channels were fabricated on the top (facing incident light) and bottom side of the sample and the resulting geometries were analyzed. The results show a higher sensitivity to experimental parameters for bottom side ablation which was ascribed to material incubation effects. Moreover, on the top side, the resulting geometry has a V-shape, independent of experimental parameters, related to the numerical aperture of the focusing lens, which was ascribed to shadowing effects.After this work, the focus shifted towards optical fibers, UV-induced fiber Bragg gratings (FBGs) and thermal processing with conventional oven and with a CO2 laser as a source of radiant heat.First, a system for CO2 laser heating of optical fibers was constructed. For measuring the temperature of the processed fibers, a special type of FBG with high temperature stability, referred to as "Chemical Composition Grating" (CCG) was used. A thorough characterization and temperature calibration was performed and the results show the temperature dynamics with a temporal resolution of less than one millisecond. The temperature profile of the fiber and the laser beam intensity profile could be measured with a spatial resolution limited by the grating length and diameter of the fiber. Temperatures as high as ~ 1750 °C could be measured with corresponding heating and cooling rates of 10.500 K/s and 6.500 K/s.Subsequently, a thorough investigation of annealing and thermal regeneration of FBGs in standard telecommunication fibers was performed. The results show that thermal grating regeneration involves several mechanisms. For strong regeneration, an optimum annealing temperature near 900 C was found. Two different activation energies could be extracted from an Arrhenius of index modulation and Braggv iwavelength, having a crossing point also around 900 °C, indication a balance of two opposing mechanisms.Finally, the thermal dynamics and spectral evolution during formation of long period fiber gratings (LPGs) were investigated. The gratings were fabricated using the CO2 laser system by periodically grooving the fibers by thermal ablation. Transmission losses were reduced by carefully selecting the proper processing conditions. These parameters were identified by mapping groove depth and transmission loss to laser intensity and exposure time. / Huvudtemana i denna avhandling är fotokänslighet och fotostrukturering av optiska fibrer och bulk glas. Trots att forskning inom fotokänslighet i glas och optiska fibrer har pågått under mer än tre decennier är de bakomliggande mekanismerna ännu inte klarlagda. Syftet var att få en bättre förståelse för fotoresponsen genom att studera fotokäsligheten ur ett termodynamiskt perspektiv, i motsats till etablerad forskning med fokus på punktdefekter och strukturförändringar, samt mekaniska spännings effekter i optiska fibrer. Optiska fibrer användes för flertalet av de experimentella studierna av två skäl; för det första är fotokänsligheten i fibrer större och dessutom vet man mindre om bakomliggande mekanismer jämfört med motsvarande bulk glas, och för det andra kan fibrer vara enklare att studera eftersom de experimentellt kan ses som en endimensionell struktur.Inledningsvis utfördes ablaherings experiment på bulk glas med en infraröd laser med pikosekund pulser. Raka kanaler med ett designtvärsnitt på 40x40 μm tillverkades på ovansidan (mot infallande ljus) och bottensidan av provet och de resulterande geometrierna analyserades. Resultaten visar en högre känslighet för variationer i experimentella parametrar vid ablahering på undersidan vilket kan förklaras av inkubations effekter i materialet. Dessutom är den resulterande geometrin på ovansidan V-formad, oavsett experimentella parametrar, vilket kunde relateras till den numeriska aperturen hos den fokuserande linsen, vilket förklaras av skuggningseffekter.Efter detta arbete flyttades fokus mot optiska fibrer, UV inducerade fiber Bragg gitter (FBG), och termisk bearbetning med konventionell ugn samt även med en CO2-laser som källa för strålningsvärme.Först konstruerades ett system för CO2-laservärmning av fibrer. För mätning av temperaturen hos bearbetade fibrer användes en speciell sorts FBG med hög temperaturstabilitet, kallade ”Chemical Composition Gratings” (CCG). En grundlig karaktärisering och temperaturkalibrering utfördes och temperaturdynamiken mättes med en tidsupplösning på under en millisekund. Temperaturprofilen i fibern, och laserns strålprofil, kunde mätas med en spatiell upplösning begränsad av gitterlängden och fiberns diameter. Temperaturer upp till ~1750 °C, vilket är högre än mjukpunktstemperaturen, kunde mätas med korresponderande uppvärmnings- och avsvalningshastighet på 10.500 K/s och 6.500 K/s.Därefter gjordes en omfattande undersökning av värmebearbetning och termisk regenerering av FBG:er i telekomfiber. Resultaten visar att termisk gitter-regenerering aktiveras av flera olika mekanismer. Värmebearbetning vid en temperatur omkring 900 °C resulterade i starka gitter efter en regenerering vid en temperatur på 1100 °C. Två olika aktiveringsenergier kunde extraheras från en Arrhenius plot avseende brytningsindexmodulation och Braggvåglängd, med en skärningspunkt tillika runt 900 °C, vilket indikerar en avvägning mellan två motverkande mekanismer vid denna temperatur.Slutligen undersöktes temperaturdynamiken och de spektrala egenskaperna under tillverkning av långperiodiga fibergitter (LPG). Gittren tillverkades med CO2-vi iilasersystemet genom att skapa en periodisk urgröpning medelst termisk ablahering. Transmissionsförluster kunde reduceras med noggrant valda processparametrar. Dessa parametrar identifierades genom mätningar av ablaherat djup och transmissionsförlust som funktion av laserintensitet och exponeringstid. / <p>QC 20150924</p>

Coarse Wavelength Division Multiplexing (CWDM) is becoming a popular way to increase the optical throughput of fibers for short to medium haul networks at a reduced cost. The International Telecommunications Union (ITU) has defned the CWDM network to consist of eighteen channels with channel spacings of 20 nm starting at 1270 nm and ending at 1610 nm.Four and eight channel AWGs on InP, suitable for CWDM, were fabricated using a novel and versatile S-shape design. The standard horseshoe layout will not work on semiconductor for AWGs with a free spectral range (FSR) larger than 30 nm. The AWG design provides operation insensitive to thermal and polarization fluctuations, which is key for low cost operation and packaging. It will be shown thatrefractive index changes over the large operating wavelength band produced negligible effects in the transmission spectrum.Standard AWG design assumes refractive index is a constant over the operating wavelength band. As a result, the output waveguide separations are held constant on the second star coupler. As the channel number increases, secondary focal dispersion causedfrom a changing refractive index can have detrimental effects on performance. A new design method will be introduced which includes refractive index dispersion by allowing the output waveguide separations to vary. The new design is consistent with standard design but is applicable in materials with a linear index dispersion over an arbitrarily large wavelength band.Lastly, a method for increasing the transmission using multimode waveguides is discussed. Traditionally, single mode waveguides are required in order to prevent higher order waveguide modes creating ghost images in the output spectrum. Using bend loss and waveguide junction offsets, higher order modes can be filtered from the output,thereby eliminating ghost images and at the same time, increase transmission.

A novel nano-structure is proposed to enhance extraordinary optical transmission from a periodic array of nano-holes. The Plasmonic Bragg reflector works by recapturing surface plasmons that are scattered off the edge of the array during the extraordinary optical transmission process, and reflecting them back towards the array where they can interfere with the light and enhance transmission. This reduces losses from a subwavelength aperture array. The reflectors are positioned to reflect in-phase with the light transmission. Polarization sensitivity of the plasmonic Bragg reflector is demonstrated. Modulation of the transmission is achieved by varying the separation between the array and reflectors. Isolation of adjacent structures on a plasmonic device by the use of the Bragg reflectors is attempted. Transmission and diffraction properties of quasiperiodic nano-hole arrays in a gold film are studied. Resonant transmission is observed, whose values do not simply match surface plasmon wave-vector values. Rotationally symmetric diffraction from the quasicrystal nano-hole array. This diffraction is seen to be controllable by the polarization of the excitation laser. Finite difference time domain calculations of the quasiperiodic array are performed to better understand the origin of the observed transmission resonances. Good agreement between theory and experiment is observed. Calculations show the formation of near-field hot-spots over the structure.

No description available.

Diffractive optical elements (DOEs) serve an important function in many dynamic and static optical systems. The theory and design of surface diffractive structures are well understood and practically applied at high spatial and phase resolution for a wide range of optical applications in science and industry. However, these structures normally only harness phase modulation of uniform fields for the beam diffraction and therefore limit their range of application, as well as being susceptible to surface damage. Multilayered volume diffractive elements offer a powerful opportunity to harness both phase and amplitude modulation for benefits in diffraction efficiency and beam shaping. However, multilayered combinations have been difficult to fabricate and provide only weak diffraction for phase gratings with low refractive index contrast. The advent of femtosecond laser writing inside transparent media has enabled the facile embedding of optical devices such as waveguides and diffractive optics into novel three-dimensional geometries that offer advanced functionality with compact design. In this work, femtosecond laser writing is pushed to the limits of forming high resolution phase elements with sufficiently strong refractive index contrast on which to develop volume phase gratings with the highest diffractive efficiency. The formation of both positive and negative zones of refractive index contrast together with rapid Talbot self imaging inside weakly contrasting phase gratings are major challenges here diminish the efficiency of assembled gratings. A method of strategic layering of otherwise weakly diffracting gratings onto Talbot planes is introduced to demonstrate, in FDTD models, the definitive enhancement of overall diffraction efficiency. A systematic optimization of laser writing in fused silica verify this enhancement or diminishment with weak volume gratings assembled on aligned or misaligned on Talbot planes. Advanced laser beam control methods were further demonstrated that underpin new direction for the facile assembly of highly functional DOEs that can exploit coherent light diffraction for opportunities in improving the performance of holographic devices and extend further to the powerful combination of phase and amplitude modulation control that is potentially available in a single optical device, thereby opening new directions for the design and fabrication of robust and strongly diffracting volume optical devices.

Diffractive optical elements (DOEs) serve an important function in many dynamic and static optical systems. The theory and design of surface diffractive structures are well understood and practically applied at high spatial and phase resolution for a wide range of optical applications in science and industry. However, these structures normally only harness phase modulation of uniform fields for the beam diffraction and therefore limit their range of application, as well as being susceptible to surface damage. Multilayered volume diffractive elements offer a powerful opportunity to harness both phase and amplitude modulation for benefits in diffraction efficiency and beam shaping. However, multilayered combinations have been difficult to fabricate and provide only weak diffraction for phase gratings with low refractive index contrast. The advent of femtosecond laser writing inside transparent media has enabled the facile embedding of optical devices such as waveguides and diffractive optics into novel three-dimensional geometries that offer advanced functionality with compact design. In this work, femtosecond laser writing is pushed to the limits of forming high resolution phase elements with sufficiently strong refractive index contrast on which to develop volume phase gratings with the highest diffractive efficiency. The formation of both positive and negative zones of refractive index contrast together with rapid Talbot self imaging inside weakly contrasting phase gratings are major challenges here diminish the efficiency of assembled gratings. A method of strategic layering of otherwise weakly diffracting gratings onto Talbot planes is introduced to demonstrate, in FDTD models, the definitive enhancement of overall diffraction efficiency. A systematic optimization of laser writing in fused silica verify this enhancement or diminishment with weak volume gratings assembled on aligned or misaligned on Talbot planes. Advanced laser beam control methods were further demonstrated that underpin new direction for the facile assembly of highly functional DOEs that can exploit coherent light diffraction for opportunities in improving the performance of holographic devices and extend further to the powerful combination of phase and amplitude modulation control that is potentially available in a single optical device, thereby opening new directions for the design and fabrication of robust and strongly diffracting volume optical devices.

Thesis (M.Eng.)--University of Wollongong, 2006. / Typescript. Includes bibliographical references: leaf 101-106.

Thesis (Ph. D.)--Virginia Polytechnic Institute and State University, 1997. / Vita. Abstract. Includes bibliographical references (leaves 148-155). Also available electronically via Internet.

Thesis (M.App.Sc.) - Carleton University, 2007. / Includes bibliographical references (p. 105-109). Also available in electronic format on the Internet.

The question of how shape is represented is of central interest to understanding visual processing in cortex. While tuning properties of the cells in early part of the ventral visual stream, thought to be responsible for object recognition in the primate, are comparatively well understood, several different theories have been proposed regarding tuning in higher visual areas, such as V4. We used the model of object recognition in cortex presented by Riesenhuber and Poggio (1999), where more complex shape tuning in higher layers is the result of combining afferent inputs tuned to simpler features, and compared the tuning properties of model units in intermediate layers to those of V4 neurons from the literature. In particular, we investigated the issue of shape representation in visual area V1 and V4 using oriented bars and various types of gratings (polar, hyperbolic, and Cartesian), as used in several physiology experiments. Our computational model was able to reproduce several physiological findings, such as the broadening distribution of the orientation bandwidths and the emergence of a bias toward non-Cartesian stimuli. Interestingly, the simulation results suggest that some V4 neurons receive input from afferents with spatially separated receptive fields, leading to experimentally testable predictions. However, the simulations also show that the stimulus set of Cartesian and non-Cartesian gratings is not sufficiently complex to probe shape tuning in higher areas, necessitating the use of more complex stimulus sets.