<div>This thesis proposes an Adaptive Rule-Based Energy Management Strategy (ARBS EMS) for a parallel hybrid electric vehicle (P-HEV). The strategy can effciently be deployed online without the need for complete knowledge of the entire duty cycle in order to optimize fuel consumption. ARBS improves upon the established Preliminary Rule-Based Strategy (PRBS) which has been adopted in commercial vehicles. When compared to PRBS, the aim of ARBS is to maintain the battery State of Charge (SOC) which ensures the availability of the battery over extended distances. The proposed strategy prevents the engine from operating in highly ineffcient regions and reduces the total equivalent fuel consumption of the vehicle. Using an HEV model developed in Simulink, both the proposed ARBS and the established PRBS strategies are compared across eight short duty cycles and one long duty cycle with urban and highway characteristics. Compared to PRBS, the results show that, on average, a 1.19% improvement in the miles per gallon equivalent (MPGe) is obtained with ARBS when the battery initial SOC is 63% for short duty cycles. However, as opposed to PRBS, ARBS has the advantage of not requiring any prior knowledge of the engine efficiency maps in order to achieve optimal performance. This characteristics can help in the systematic aftermarket hybridization of heavy duty vehicles.</div>

<p>Hybrid electric vehicles are considered to be an important part of the future vehicle industry, since they decrease fuel consumption without decreasing the performance compared to a conventional vehicle. They use two or more power sources to propel the vehicle, normally one combustion engine and one electric machine. These power sources can be arranged in different topologies and can cooporate in different ways. In this thesis, dynamic models of parallel and series hybrid powertrains are developed, and different strategies for how to control them are compared.An optimization algorithm for decreasing fuel consumption and utilize the battery storage capacity as much as possible is also developed, implemented and tested.</p>

<p>Hybrid electric vehicles have two power sources - an internal combustion engine and an electric motor. These vehicles are of great interest because they contribute to a decreasing fuel consumption and air pollution and still maintain the performance of a conventional car. Different topologies are described in this thesis and especially the series and parallel hybrid electric vehicle and Toyota Prius have been studied. </p><p>This thesis also depicts modelling of a reference car and a series hybrid electric vehicle in Modelica. When appropriate, models from the Modelica standard library have been used. Models for a manual gearbox, final drive, wheel, chassis, air drag and a driver have been developed for the reference car. </p><p>For the hybrid electric vehicle a continuously variable transmission, battery, an electric motor, fuel cut-off function for the internal combustion engine and a converter that distributes the current between generator, electric motor and internal combustion engine have been designed. </p><p>These models have been put together with models from the Modelica standard library to a reference car and a series hybrid electric vehicle which follows the NEDC driving cycle. A sketch for the parallel hybrid electric vehicle and Toyota Prius have also been made in Modelica. </p><p>Developed models have been introduced into the Modelica library VehProLib, which is a vehicle propulsion library under development by Vehicular Systems, Linköpings universitet.</p>

There is an increasing interest in sustainability and a growing debate about environmental policy measures aiming at the reduction of green house gas emissions across di erent economic sectors worldwide. The transportation sector is one major greenhouse gas emitter which is heavily regulated to reduce its dependance on oil. These regulations along with the growing customer awareness about global warming has led vehicle manufacturers to seek di erent technologies to improve vehicle e ciencies and reduce the green house gases emissions while at the same time meeting customer's expectation of mobility and exibility. Plug-in hybrid electric vehicles (PHEV) is one major promising solution for a smooth transition from oil dependent transportation sector to a clean electric based sector while not compromising the mobility and exibility of the drivers. In the medium term, plug-in hybrid electric vehicles (PHEV) can lead to signi cant reductions in transportation emissions. These vehicles are equipped with a larger battery than regular hybrid electric vehicles which can be recharged from the grid. For short trips, the PHEV can depend solely on the electric engine while for longer journeys the alternative fuel can assist the electric engine to achieve extended ranges. This is bene cial when the use pattern is mixed such that and short long distances needs to be covered. The plug-in hybrid electric vehicles are well-suited for logistics since they can avoid the possible disruption caused by charge depletion in case of all-electric vehicles with tight time schedules. The use of electricity and fuel gives rise to a new variant of the classical vehicle routing with time windows which we call the plug-in hybrid electric vehicle routing problem with time windows (PHEVRPTW). The objective of the PHEVRPTW is to minimize the routing costs of a eet of PHEVs by minimizing the time they run on gasoline while meeting the demand during the available time windows. As a result, the driver of the PHEV has two decisions to make at each node: (1) recharge the vehicle battery to achieve a longer range using electricity, or (2) continue to the next open time window with the option of using the alternative fuel. In this thesis, we present a mathematical formulation for the plug-in hybrid-electric vehicle routing problem with time windows. We solve this problem using a Lagrangian relaxation and we propose a new tabu search algorithm. We also present the rst results for the full adapted Solomon instances.

Performance of two different waste heat recovery systems (one based on Rankine cycle and the other one using thermoelectricity) combined with non-hybrid, mild-hybrid and full hybrid systems are investigated. The vehicle under investigation was a 440hp Scania truck, loaded by 40 tons. Input data included logged data from a long haulage drive test in Sweden.All systems (waste heat recovery as well as hybrid) are implemented and simulated in Matlab/Simulink. Almost all systems are modeled using measured data or performance curves provided by one manufacturer. For Rankine system results from another investigation were used.Regardless of practical issues in implementing systems, reduction in fuel consumption for six different combination of waste heat recovery systems and hybrid systems with different degrees of hybridization are calculated. In general Rankine cycle shows a better performance. However, due to improvements achieved in laboratories, thermoelectricity could also be an option in future.This study focuses on “system” point of view and therefore high precision calculations is not included. However it can be useful in making decisions for further investigations.

The main goal of this thesis study is the optimization of the basic design parameters of hybrid electric vehicle drivetrain components to minimize fuel consumption and emission objectives, together with constraints derived from performance requirements. In order to generate a user friendly and flexible platform to model, select drivetrain components, simulate performance, and optimize parameters of series and parallel hybrid electric vehicles, a MATLAB based graphical user interface is designed. A basic sizing procedure for the internal combustion engine, electric motor, and battery is developed. Pre-defined control strategies are implemented for both types of hybrid configurations. To achieve better fuel consumption and emission values, while satisfying nonlinear performance constraints, multi-objective gradient based optimization procedure is carried out with user defined upper and lower bounds of optimization parameters. The optimization process is applied to a number of case studies and the results are evaluated by comparison with similar cases found in literature.

Hybrid electric vehicle technology has become a preferred method for the automotive industry to reduce environmental impact and fuel consumption of their vehicles. Hybrid electric vehicles accomplish these reductions through the use of multiple propulsion systems, namely an electric motor and internal combustion engine, which allow the elimination of idling, operation of the internal combustion engine in a more efficient manner and the use of regenerative braking. However, the added cost of the hybrid electric system has hindered the sales of these vehicles. A more cost effective design of an electro-hydraulic braking system is presented. The system electro-mechanically controlled the boost force created by the brake booster independently of the driver braking force and with adequate time response. The system allowed for the blending of the mechanical and regenerative braking torques in a manner transparent to the driver and allowed for regenerative braking to be conducted efficiently. A systematic design process was followed, with emphasis placed on demonstrating conceptual design feasibility and preliminary design functionality using virtual and physical prototyping. The virtual and physical prototypes were then used in combination as a powerful tool to validate and develop the system. The role of prototyping in the design process is presented and discussed. Through the experiences gained by the author during the design process, it is recommended that students create physical prototypes to enhance their educational experience. These experiences are evident throughout the thesis presented.

Increased environmental awareness together with new legislative demands on lowered emissions and a rising fuel cost have put focus on increasing the fuel efficiency in new vehicles. Hybridization is a way to increase the efficiency of the powertrain.The Haldex electric Torque Vectoring Device is a rear axle with a built in electric motor, designed to combine all-wheel drive with hybrid functionality. A method is developed for creating a real time control algorithm that minimizes the fuel consumption. First the consumption reduction potential of the system is investigated using Dynamic Programming. A real time control algorithm is then devised that indicates a substantial consumption reduction potential compared to all-wheel drive, under the condition that the assumed and measured efficiencies are accurate. The control algorithm is created using equivalent consumption minimization strategy and is implemented without any knowledge of the future driving mission. Two ways of adapting the control according to the battery state of charge are proposed and investigated. The controller optimizes the torque distribution for the current gear as well as assists the driver by recommending the gear which would give the lowest consumption. The simulations indicate a substantial fuel consumption reduction potential even though the system primarily is an all-wheel drive concept. The results from vehicle tests show that the control system is charge sustaining and the driveability is deemed good by the test-drivers.

Hybrid electric vehicles are considered to be an important part of the future vehicle industry, since they decrease fuel consumption without decreasing the performance compared to a conventional vehicle. They use two or more power sources to propel the vehicle, normally one combustion engine and one electric machine. These power sources can be arranged in different topologies and can cooporate in different ways. In this thesis, dynamic models of parallel and series hybrid powertrains are developed, and different strategies for how to control them are compared.An optimization algorithm for decreasing fuel consumption and utilize the battery storage capacity as much as possible is also developed, implemented and tested.

Hybrid electric vehicles have two power sources - an internal combustion engine and an electric motor. These vehicles are of great interest because they contribute to a decreasing fuel consumption and air pollution and still maintain the performance of a conventional car. Different topologies are described in this thesis and especially the series and parallel hybrid electric vehicle and Toyota Prius have been studied. This thesis also depicts modelling of a reference car and a series hybrid electric vehicle in Modelica. When appropriate, models from the Modelica standard library have been used. Models for a manual gearbox, final drive, wheel, chassis, air drag and a driver have been developed for the reference car. For the hybrid electric vehicle a continuously variable transmission, battery, an electric motor, fuel cut-off function for the internal combustion engine and a converter that distributes the current between generator, electric motor and internal combustion engine have been designed. These models have been put together with models from the Modelica standard library to a reference car and a series hybrid electric vehicle which follows the NEDC driving cycle. A sketch for the parallel hybrid electric vehicle and Toyota Prius have also been made in Modelica. Developed models have been introduced into the Modelica library VehProLib, which is a vehicle propulsion library under development by Vehicular Systems, Linköpings universitet.