Energy from the sun can be converted to low cost electricity using dye-sensitized solar cells (DSCs). Dye molecules adsorbed to the surface of mesoporous TiO2 absorb light and inject electrons into the semiconductor. They are then regenerated by the reduced redox species from an electrolyte, typically consisting of the iodide/tri-iodide redox couple in an organic solvent. In a solid state version of the DSC, the liquid electrolyte is replaced by an organic hole conductor. Solid state DSCs using 2,2'7,7'-tetrakis-(N,N-di-p-methoxyphenyl-amine)-9,9'-spirobifluorene (spiro-MeOTAD) have reached conversion efficiencies of up to 6 %, which is about half of the efficiency of the best iodide/tri-iodide cells.   Measurement techniques, such as spectroelectrochemistry and photo-induced absorption spectroscopy (PIA), were developed and applied to study the working mechanism of organic dyes in solid state DSCs under solar cell operating conditions. The energy alignment of the different solar cell components was studied by spectroelectrochemistry and the results were compared to photoelectron spectroscopy. PIA was used to study the injection and regeneration processes. For the first time, it was shown here that the results of PIA are influenced by an electric field due to the electrons injected into the TiO2. This electric field causes a shift in the absorption spectrum of dye molecules adsorbed to the TiO2 surface due to the Stark effect.   Taking the Stark effect into consideration during the data analysis, mechanistic differences between solid state and conventional DSCs were found. A perylene dye, ID176, was only able to efficiently inject electrons into the TiO2 in presence of lithium ions and in absence of a solvent. As a result, the sensitiser worked surprisingly well in solid state DSCs but not in liquid electrolyte ones. Regeneration of oxidised dye molecules by spiro-MeOTAD was found to be fast and efficient and spiro-MeOTAD could even reduce excited dye molecules.

No description available.

We have presented a thorough experimental investigation of electroabsorption spectroscopy on quasi-one-dimensional organic molecular crystals such as PTCDA and MePTCDI vapor deposited thin films to clarify the involvement of the charge-transfer exciton in the lowest excited state. By a self-built experimental setup, two kinds of electroabsorption measurements, called "perpendicular" and "parallel" measurements, were conducted at room temperature in ambient air. The crystalline texture of PTCDA and MePTCDI thin film samples are characterized by X-ray diffraction measurements. Current-voltage, capacitance-frequency and capacitance-voltage measurements are performed to clarify the electric field distribution inside organic layers. The results from electrical measurements show that only under certain conditions (electroabsorption measurements with proDC bias), the perpendicular and parallel electroabsorption meaurements can be directly compared. The electroabsorption spectra of MePTCDI and PTCDA thin films can be interpreted by neither pure Frenkel exciton nor pure charge-transfer exciton model. Essential features of electroabsorption spectra of MePTCDI and PTCDA thin films can be understood by the the mixture of Frenkel and charge-transfer exciton model. However, there is still a discrepancy in the directional properties of electroabsorption signals between experimental results and modle calculations. This small discrepancy suggests that a full interpretation of electroabsorption spectra of quasi-one-dimensional organic molecular crystals needs further experimental and theoretical investigations.

No description available.

The solid-state mesoscopic solar cells (sMSCs) have been developed as a promising alternative technology to the conventional photovoltaics. However, the device performance suffers from the low hole-mobilities and the incomplete pore filling of the hole transport materials (HTMs) into the mesoporous electrodes. A variety of HTMs and different preparation methods have been studied to overcome these limitations. There are two types of sMSCs included in this doctoral thesis, namely solid-state dye-sensitized solar cells (sDSCs) and organometallic halide perovskite based solar cells. Two different types of HTMs, namely the small molecule organic HTM spiro-OMeTAD and the conjugated polymer HTM P3HT, were compared in sDSCs. The photo-induced absorption spectroscopy (PIA) spectra and spectroelectrochemical data suggested that the dye-dye hole conduction occurs in the absence of HTM and appears to be of significant importance to the contribution of hole transport. The PIA measurements and transient absorption spectroscopy (TAS) indicated that the oxidized dye was efficiently regenerated by a small molecule organic HTM TPAA due to its excellent pore filling. The conducting polymer P3HT was employed as a co-HTM to transfer the holes away from TPAA to prohibit the charge carrier recombination and to improve the hole transport. An alternative small molecule organic HTM, MeO-TPD, was found to outperform spiro-OMeTAD in sDSCs due to its more efficient pore filling and higher hole-mobility. Moreover, an initial light soaking treatment was observed to significantly improve the device performance due to a mechanism of Li+ ion migration towards the TiO2 surface. In order to overcome the infiltration difficulty of conducting polymer HTMs, a state-of-the-art method to perform in-situ photoelectrochemical polymerization (PEP) in an aqueous micellar solution of bis-EDOT monomer was developed as an environmental-friendly alternative pathway with scale-up potential for constructing efficient sDSCs with polymer HTMs. Three different types of HTMs, namely DEH, spiro-OMeTAD and P3HT, were used to investigate the influence of HTMs on the charge recombination in CH3NH3PbI3 perovskite based sMSCs. The photovoltage decay measurements indicate that the electron lifetime (τn) of these devices decreases by one order of magnitude in the sequence τspiro-OMeTAD > τP3HT > τDEH.

The rapidly increasing power conversion efficiencies (PCEs) of organic solar cells (OSCs) above 10% were made possible by concerted international research activities in the last few years, aiming to understand the processes that lead to the generation of free charge carriers following photon absorption. Despite these efforts, many details are still unknown, especially how these processes can be improved already at the drawing board of molecular design. To unveil this information, dicyanovinyl end-capped oligothiophene derivatives (DCVnTs) are used as a model system in this thesis, allowing to investigate the impact of small structural changes on the molecular properties and the final solar cells. On thin films of a methylated DCV4T derivative, the influence of the measurement temperature on the charge carrier generation process is investigated. The observed temperature activation in photoinduced absorption (PIA) measurements is attributed to an increased charge carrier mobility, increasing the distance between the charges at the donor/acceptor (D/A) interface and, thus, facilitating their final dissociation. The correlation between the activation energy and the mobility is confirmed using a DCV6T derivative with lower mobility , exhibiting a higher activation energy for charge carrier generation. Another parameter to influence the charge carrier generation process is the molecular structure. Here, alkyl side chains with varying length are introduced and their influence on the intramolecular energy levels as well as the absorption and emission properties in pristine and blend films with the acceptor C60 are examined. The observed differences in intermolecular order (higher order for shorter side chains) and phase separation in blend layers (larger phase separation for shorter side chains) are confirmed in PIA measurements upon comparing the temperature dependence of the triplet exciton lifetimes. A proposed correlation between the side chain length and the coupling between D and A, which is crucial for efficient charge transfer, is not confirmed. The presented flat heterojunction solar cells underline this conclusion, giving similar photocurrent densities for all compounds. Differences in PCE are related to shifts of the energy levels and the morphology of the blend layer in bulk heterojunction devices. Furthermore, the impact of the electric field on the charge carrier generation yield is investigated in a proof-of-principle study, introducing PIA measurements in transmission geometry realized using semitransparent solar cells. The recombination analysis of the photogenerated charge carriers reveals two recombination components. Trapped charge carriers or bound charge pairs at the D/A interface are proposed as an explanation for this result. The miscibility of D and A, which can be influenced by heating the substrate during layer deposition, is of crucial importance to obtain high PCEs. In this work, the unusual negative influence of the substrate temperature on DCV4T:C60 blend layers in solar cells is investigated. By using optical measurements and structure determination tools, a rearrangement of the DCV4T crystallites is found to be responsible for the reduced absorption and, therefore, photocurrent at higher substrate temperature. The proposed blend morphology at a substrate temperature of 90° C is characterized by a nearly complete demixing of the D and A phases. This investigation is of particular relevance, because it shows the microscopic origins of a behavior that is contrary to the increase of the PCE upon substrate heating usually reported in literature. Finally, the optimization steps to achieve a record PCE of 7.7% using a DCV5T derivative as donor material are presented, including the optimization of the substrate temperature, the active layer thickness, and the transport layers. / Der rasante Anstieg des Wirkungsgrads von organischen Solarzellen über die Marke von 10% war nur durch länderübergreifende Forschungsaktivitäten während der letzten Jahre möglich. Trotz der gemeinsamen Anstrengungen, die Prozesse, die zwischen der Absorption der Photonen und der Ladungsträgererzeugung liegen, genauer zu verstehen, sind einige Fragen jedoch immer noch ungelöst, z.B. wie diese Prozesse schon auf dem Reißbrett durch die gezielte Änderung bestimmter Molekülstrukturen optimiert werden können. Um dieses Ziel zu erreichen, werden in dieser Arbeit Dicyanovinyl-substituierte Oligothiophene (DCVnTs) verwendet. Diese Materialien bieten die Möglichkeit, kleine strukturelle Änderungen vorzunehmen, deren Einfluss auf die molekularen und auf die Solarzelleneigenschaften untersucht werden soll. Der Einfluss der Messtemperatur auf den Prozess der Ladungsträgertrennung wird hier an einer methylierten DCV4T-Verbindung in einer dünnen Schicht untersucht. Die bei photoinduzierter Absorptionsspektroskopie (PIA) beobachtete Aktivierung dieses Prozesses mit zunehmender Temperatur wird auf eine erhöhte Ladungsträgerbeweglichkeit zurückgeführt. Der dadurch erhöhte effektive Abstand der Ladungen an der Grenzfläche zwischen Donator (D) und Akzeptor (A) erleichtert die endgültige Trennung der Ladungsträger. Durch den Vergleich mit einer DCV6T-Verbindung wird der Zusammenhang zwischen der Aktivierungsenergie und der Beweglichkeit bekräftigt. Die kleinere Beweglichkeit äußert sich dabei in einer größeren Aktivierungsenergie. Darüber hinaus kann der Ladungsträgergenerationsprozess auch von der Molekülstruktur abhängen. In dieser Arbeit wird untersucht, wie sich die Länge von Alkylseitenketten auf die Energieniveaus der Moleküle, aber auch auf die Absorptions- und Lumineszenzeigenschaften der Materialien in reinen und in Mischschichten mit dem Akzeptor C60 äußert. Die ermittelten Unterschiede bezüglich der Molekülordnung (geordneter für kürzere Seitenketten) und der Phasengrößen in Mischschichten (größere Phasen bei kürzerer Kettenlänge) werden in der Untersuchung der Temperaturabhängigkeit der Lebensdauer von Triplettexzitonen mittels PIA-Messungen bestätigt. Für Solarzellen ist von Bedeutung, ob sich die Seitenkettenlänge auf die Wechselwirkung zwischen D und A auswirkt. Der vermutete Zusammenhang wird hier nicht bestätigt. Ein ähnlicher Photostrom für alle untersuchten Verbindungen in Solarzellen mit planaren Heteroübergängen unterstreicht diese Schlussfolgerung. Unterschiede im Wirkungsgrad werden auf Änderungen der Energieniveaus und die Morphologie in Mischschichtsolarzellen zurückgeführt. Des Weiteren wird in einer Machbarkeitsstudie der Einfluss des elektrischen Felds auf die Generationsausbeute freier Ladungsträger untersucht. Dafür werden halbtransparente Solarzellen verwendet, die es ermöglichen, PIA-Messungen in Transmissionsgeometrie durchzuführen. Als mögliche Erklärung für das Auftreten zweier Rekombinationskomponenten in der Analyse des Rekombinationsverhaltens der durch Licht erzeugten Ladungsträger werden eingefangene Ladungsträger und gebundene Ladungsträgerpaare an der D/A-Grenzfläche genannt. Das Mischverhalten von D und A kann durch ein Heizen des Substrates während des Verdampfungsprozesses eingestellt werden, was von entscheidender Bedeutung für eine weitere Steigerung des Wirkungsgrades ist. Für DCV4T:C60-Mischschichtsolarzellen wird jedoch eine Verschlechterung des Wirkungsgrads zu höheren Substrattemperaturen beobachtet. Durch optische Messungen und Methoden zur Schichtstrukturbestimmung wird dieser Effekt auf eine Umordnung der DCV4T-Kristallite für hohe Substrattemperaturen und die damit verbundene Verringerung der Absorption und damit auch des Photostroms zurückgeführt. Bei einer Substrattemperatur von 90° C sind die D- und A-Komponenten fast vollständig entmischt. Dieses Beispiel ist von besonderer Bedeutung, weil hier die Ursachen für ein Verhalten aufgezeigt werden, das entgegen den Beispielen aus der Literatur eine Abnahme des Wirkungsgrads beim Aufdampfen der aktiven Schicht auf ein geheiztes Substrat zeigt. Schließlich werden die Optimierungsschritte dargelegt, mit denen Solarzellen mit einer DCV5T-Verbindung als Donatormaterial auf einen Rekordwirkungsgrad von 7,7% gebracht werden. Dabei wird die Substrattemperatur, die Dicke der aktiven Schicht und die Transportschichten angepasst.

Le premier volet de cette thèse est consacré à la modélisation des phénomènes de transport dans le LN. Partant d'une analyse critique des modèles de bande usuels, nous montrons leur inadéquation dans le cas du LN et nous proposons un modèle de saut basé sur la théorie des petits polarons. Nous étudions d'abord par simulation Monte-Carlo la décroissance d'une population de polarons liés NbLi4+ relaxant vers des pièges profonds FeLi3+. Nous montrons que les pièges FeLi3+ ont des rayons effectifs particulièrement grands, rayons qui augmentent encore à température décroissante, et limitent considérablement les longueurs de diffusion des polarons. Les résultats de simulations sont ensuite confrontés aux résultats expérimentaux obtenus par différentes techniques ; Absorption photo-induite, Raman, Enregistrement holographique et Pompe-sonde. Le deuxième volet de cette thèse est consacré aux applications électro-optiques dans le LN périodiquement polarisé (PPLN). Sous l’effet d’une tension électrique, l’indice de réfraction du PPLN est périodiquement diminué et augmenté, formant ainsi un réseau d’indice activable électriquement. Un premier composant utilisant l’effet électro-optique dans du PPLN a été développé et démontré expérimentalement. Dans ce composant, la lumière est défléchie sous l’effet de la tension électrique par le réseau d’indice. Ce déflecteur de Bragg atteint une efficacité de diffraction proche de 100% avec une faible tension de commande de l’ordre de 5 V. Un deuxième composant a également été proposé, où la lumière se propage perpendiculairement aux parois de domaines du PPLN. Dans cette configuration un réflecteur de Bragg électro-optique peut être réalisé / The first part of this thesis is devoted to the modeling of transport phenomena in the LN. From a critical analysis of the usual band models, we show their inadequacy in the case of LN and we propose a hopping model based on the theory of small polarons. We first study by Monte-Carlo simulation the population decay of bound polarons NbLi4+ in deep traps FeLi3+. We show that the traps (FeLi3+) have particularly large effective radii, which increase further at decreasing temperature, and considerably limit the diffusion lengths of the polarons. The results of simulations are then compared with experimental results obtained by different techniques; Light-induced absorption, Raman, Holographic storage and Pump-Probe. The second part of this thesis is devoted to electro-optical applications in the periodically poled LN (PPLN). Under the effect of an electrical voltage, the refractive index of the PPLN is periodically decreased and increased, thus forming an electrically activatable index grating. A first component using the electro-optical effect in PPLN has been developed and demonstrated experimentally. In this component, the light is deflected under the effect of the electrical voltage by the index grating. This Bragg deflector achieves a diffraction efficiency of close to 100% with a low drive voltage of the order of 5 V. A second component has also been proposed, where light propagates perpendicularly to the domain walls of the PPLN. In this configuration an electro-optic Bragg reflector can be realized

The subject of this thesis is the study of coherent interaction of light with matter (atoms) to improve the precision measurements and techniques. Special attention is drawn to get the narrow subnatural electromagnetically induced transmission (EIT), electromagnetically induced absorption (EIA) and nonlinear magneto-optic rotation (NMOR) caused by alkali atoms contained in a vapor cell. Subnatural polarization rotation introduces by a strong circularly polarized light in the absence of any external magnetic field was also studied. A detailed theoretical treatment, given in this dissertation, allows to associate each of the features of the spectra with a special physical mechanism. Many quantum phenomena related to interferences, coherences, optical pumping etc. experiments are studied using home-built diode lasers. This thesis also describes laser cooling and trapping of rubidium atoms using two techniques. Deflection of cold atoms horizontally from MOT using pushing beams are discussed in close consideration for the improvements in the precision measurements. This thesis is organized as follows. In Chapter 1, an introduction to the importance of sub-natural narrow resonance and simplified technique in the precision measurement will be discussed. In Chapter 2, an introduction to EIT, EIA and NMOR resonance are discussed. This chapter will provide a basic theoretical background of atom-field interactions, especially for Λ-type and N -type systems and its steady state solution using density matrix analysis and experimental tools. The most important notion of laser cooling of atoms, ions or molecule i.e., exchange of momentum between light and atoms combining with the Doppler effect will be discussed. In Chapter 3, the observation of subnatural EIT and subnatural EIA in closed and open degenerate two-level system using room temperature vapor cell filled with Rb will be presented. Physical mechanisms that contribute to EIT and EIA, and the contrast of our results from the coherent population trapping (CPT)–type resonances are discussed in detail in appendix A.2 according to our experimental results. In Chapter 4, the narrowing of subnatural EIT and subnatural EIA linewidth in closed and open systems again in degenerate two level transition, using the “Laguerre-Gaussian” control beam instead of generally studied Gaussian beam, will be discussed in detail. In Chapter 5, the conversion between subnatural EIT to subnatural EIA in a degenerate Λ system will be discussed. The physical mechanism created by the introduction of a coherent counter propagating control laser to the co-propagating probe and the control laser are studied. The effect of polarization and axial velocity Doppler averaging will also be studied. In Chapter 6, we will discuss the sensitive technique for precise measurement of small magnetic fields using the NMOR, by chopping the resonant laser beam. We will study the sensitivity and the potential application of this technique in the measurement of an atomic electric-dipole moment. In Chapter 7, we will be studying about the induced optical rotation by a circularly polarized control laser on the linearly polarized probe laser. The effect of the intensity of the control laser beam on the higher order optical rotation will also be studied. In Chapter 8, we will be studying about the cooling and trapping of 87Rb in magneto-optic trap. We will be studying two techniques of trapping of atoms in MOT. The cold cloud of atoms from the MOT are deflected horizontally by using different configuration of pushing beam are studied. A brief summary and outlook of my thesis work will be discussed at Chapter 9.

The rapidly increasing power conversion efficiencies (PCEs) of organic solar cells (OSCs) above 10% were made possible by concerted international research activities in the last few years, aiming to understand the processes that lead to the generation of free charge carriers following photon absorption. Despite these efforts, many details are still unknown, especially how these processes can be improved already at the drawing board of molecular design. To unveil this information, dicyanovinyl end-capped oligothiophene derivatives (DCVnTs) are used as a model system in this thesis, allowing to investigate the impact of small structural changes on the molecular properties and the final solar cells. On thin films of a methylated DCV4T derivative, the influence of the measurement temperature on the charge carrier generation process is investigated. The observed temperature activation in photoinduced absorption (PIA) measurements is attributed to an increased charge carrier mobility, increasing the distance between the charges at the donor/acceptor (D/A) interface and, thus, facilitating their final dissociation. The correlation between the activation energy and the mobility is confirmed using a DCV6T derivative with lower mobility , exhibiting a higher activation energy for charge carrier generation. Another parameter to influence the charge carrier generation process is the molecular structure. Here, alkyl side chains with varying length are introduced and their influence on the intramolecular energy levels as well as the absorption and emission properties in pristine and blend films with the acceptor C60 are examined. The observed differences in intermolecular order (higher order for shorter side chains) and phase separation in blend layers (larger phase separation for shorter side chains) are confirmed in PIA measurements upon comparing the temperature dependence of the triplet exciton lifetimes. A proposed correlation between the side chain length and the coupling between D and A, which is crucial for efficient charge transfer, is not confirmed. The presented flat heterojunction solar cells underline this conclusion, giving similar photocurrent densities for all compounds. Differences in PCE are related to shifts of the energy levels and the morphology of the blend layer in bulk heterojunction devices. Furthermore, the impact of the electric field on the charge carrier generation yield is investigated in a proof-of-principle study, introducing PIA measurements in transmission geometry realized using semitransparent solar cells. The recombination analysis of the photogenerated charge carriers reveals two recombination components. Trapped charge carriers or bound charge pairs at the D/A interface are proposed as an explanation for this result. The miscibility of D and A, which can be influenced by heating the substrate during layer deposition, is of crucial importance to obtain high PCEs. In this work, the unusual negative influence of the substrate temperature on DCV4T:C60 blend layers in solar cells is investigated. By using optical measurements and structure determination tools, a rearrangement of the DCV4T crystallites is found to be responsible for the reduced absorption and, therefore, photocurrent at higher substrate temperature. The proposed blend morphology at a substrate temperature of 90° C is characterized by a nearly complete demixing of the D and A phases. This investigation is of particular relevance, because it shows the microscopic origins of a behavior that is contrary to the increase of the PCE upon substrate heating usually reported in literature. Finally, the optimization steps to achieve a record PCE of 7.7% using a DCV5T derivative as donor material are presented, including the optimization of the substrate temperature, the active layer thickness, and the transport layers.:Abstract - Kurzfassung Publications Contents 1 Introduction 2 Elementary Processes in Organic Semiconductors 2.1 Introduction 2.2 Optical Excitations in Organic Materials 2.2.1 Introduction 2.2.2 Radiative Processes: Absorption and Emission 2.2.3 Non-radiative Relaxation Processes 2.2.4 Triplet Excitons and Intersystem Crossing 2.3 Polarization Effects and Disorder 2.4 Transport Processes in Disordered Organic Materials 2.4.1 Charge Transport 2.4.1.1 The Bässler Model 2.4.1.2 Marcus Theory for Electron Transfer 2.4.1.3 Small Polaron Model 2.4.1.4 Functional Dependencies of the Charge Carrier Mobility 2.4.2 Diffusive Motion 2.4.3 Exciton Transfer Mechanisms 2.4.4 Characteristics of Exciton Diffusion 2.5 Charge Photogeneration in Pristine Materials 3 Organic Photovoltaics 3.1 General Introduction to Solar Cell Physics 3.2 Introduction to the Donor/Acceptor Heterojunction Concept 3.3 The Open-Circuit Voltage in Organic Solar Cells 3.4 Doping of Organic Semiconductors 3.5 Introduction to the p-i-n Concept 3.6 Charge Transfer Excitons in Donor/Acceptor Heterojunction Systems 3.6.1 Introduction 3.6.2 Verification of Charge Transfer Excitons in Donor/Acceptor Systems 3.7 The Process Cascade for Free Charge Carrier Generation in Donor/Acceptor Heterojunction Systems 3.7.1 The Initial Charge Transfer Step 3.7.2 The Binding Energy of the Charge Transfer Exciton 3.7.3 \"Hot\" Charge Transfer Exciton Dissociation 3.7.4 \"Cold\" Charge Transfer Exciton Dissociation 3.7.5 Supposed Influence Factors on Charge Transfer Exciton Dissociation 3.7.6 Recombination Pathways for Charge Transfer Excitons 3.7.7 Free Charge Carrier Formation and Recombination 4 Experimental Methods 4.1 Sample Preparation 4.2 Material Characterization Methods 4.2.1 Optical Characterization 4.2.2 Cyclic Voltammetry 4.2.3 Ultraviolet Photoelectron Spectroscopy 4.2.4 Atomic Force Microscopy 4.2.5 Grazing Incidence X-Ray Diffraction 4.2.6 Organic Field-Effect Transistor 4.3 Photoinduced Absorption Spectroscopy 4.3.1 Introduction 4.3.2 Derivation of the PIA Signal 4.3.3 Recombination Dynamics 4.3.4 Intensity Dependence of the PIA Signal 4.4 Solar Cell Characterization 4.4.1 External Quantum Efficiency 4.4.2 Spectral Mismatch Correction 4.4.3 Current-Voltage Characteristics 4.4.4 Optical Device Simulations 4.4.5 Optical Device Transmission Measurements 5 The Oligothiophene Material System 5.1 Introduction 5.2 Thermal Stability 5.3 Energy Levels 5.4 Optical Properties of the Pristine Materials 5.5 The Donor/Acceptor Couple: DCVnT and C60 5.6 Solar Cell Devices 5.7 Summary 6 Temperature Dependence of Charge Carrier Generation 6.1 Introduction 6.2 Principal Introduction to the PIA Measurements 6.2.1 Interpretation of the Spectra 6.2.2 Interpretation of the Frequency Scans 6.3 Temperature Dependence of the Spectra 6.4 Discussion of the Temperature Dependent Processes in the Blend Layer 6.5 Temperature Activated Free Charge Carrier Generation 6.5.1 Evaluation of the Activation Energy for the DCV4T-Me:C60 Blend 6.5.2 Comparison to a Sexithiophene Derivative (DCV6T-Me) 6.6 Summary 7 Side Chain Investigation on Quaterthiophene Derivatives 7.1 Energy Levels 7.2 Optical Properties 7.2.1 Solution and Pristine Films 7.2.2 Mixed Films with C60 7.3 Influence of the Side Chain Length on the Intermolecular Coupling 7.3.1 PIA Spectra of Pristine and Blend Layers at 10K 7.3.2 Recombination Analysis for Pristine and Blend Films at 10K 7.4 The Influence of the Side Chain Length on the Offset Charge Carrier Generation Rate at Low Temperature 7.5 In the High-Temperature Limit: Implications for Solar Cell Devices 7.5.1 PIA Spectra in Pristine and Blend Films at 200K 7.5.2 Recombination Analysis: Triplet Excitons and Free Charge Carriers 7.6 Solar Cells 7.6.1 Flat Heterojunction Devices 7.6.2 Bulk Heterojunction Devices 7.7 Summary 8 Electric-Field Dependent PIA Measurements on Complete Solar Cell Devices 8.1 Introduction 8.2 Semitransparent Organic Solar Cells 8.3 Photoinduced Absorption Measurements 8.4 Summary and Outlook 9 The Effect of Substrate Heating During Layer Deposition on the Performance of DCV4T:C60 BHJ Solar Cells 9.1 Introduction 9.2 The Importance of Morphology Control for BHJ Solar Cells 9.3 The Impact of Substrate Heating on DCV4T:C60 BHJ Solar Cells 9.4 Absorption and Photoluminescence 9.5 Topographical Investigations (AFM) 9.6 X-ray Investigations 9.6.1 1D GIXRD Measurements 9.6.2 2D GIXRD Measurements 9.7 Proposed Morphological Picture and Confirmation Measurements 9.7.1 Morphology Sketch of the DCV4T:C60 Blend Layer 9.7.2 Confirmation Measurements 9.8 The Equivalence of Temperature and Time 9.9 Summary 10 Record Solar Cells Using DCV5T-Me33 as Donor Material 10.1 Introduction 10.2 The Influence of the Substrate Temperature 10.3 Determination of the Optical Constants 10.4 Stack Optimization 10.5 Summary and Outlook 11 Conclusions and Outlook 11.1 Summary of the Photophysical Investigations 11.2 Summary of Device Investigations 11.3 Future Challenges Appendix A Detailed Description of the Experimental Setup for PIA Spectroscopy Appendix B Determination of the Triplet Level by Differential PL Measurements Appendix C Additional Tables and Figures Appendix D Reproducibility of the Solar Cell Results (Statistics) Appendix E Lists Bibliography Acknowledgments / Der rasante Anstieg des Wirkungsgrads von organischen Solarzellen über die Marke von 10% war nur durch länderübergreifende Forschungsaktivitäten während der letzten Jahre möglich. Trotz der gemeinsamen Anstrengungen, die Prozesse, die zwischen der Absorption der Photonen und der Ladungsträgererzeugung liegen, genauer zu verstehen, sind einige Fragen jedoch immer noch ungelöst, z.B. wie diese Prozesse schon auf dem Reißbrett durch die gezielte Änderung bestimmter Molekülstrukturen optimiert werden können. Um dieses Ziel zu erreichen, werden in dieser Arbeit Dicyanovinyl-substituierte Oligothiophene (DCVnTs) verwendet. Diese Materialien bieten die Möglichkeit, kleine strukturelle Änderungen vorzunehmen, deren Einfluss auf die molekularen und auf die Solarzelleneigenschaften untersucht werden soll. Der Einfluss der Messtemperatur auf den Prozess der Ladungsträgertrennung wird hier an einer methylierten DCV4T-Verbindung in einer dünnen Schicht untersucht. Die bei photoinduzierter Absorptionsspektroskopie (PIA) beobachtete Aktivierung dieses Prozesses mit zunehmender Temperatur wird auf eine erhöhte Ladungsträgerbeweglichkeit zurückgeführt. Der dadurch erhöhte effektive Abstand der Ladungen an der Grenzfläche zwischen Donator (D) und Akzeptor (A) erleichtert die endgültige Trennung der Ladungsträger. Durch den Vergleich mit einer DCV6T-Verbindung wird der Zusammenhang zwischen der Aktivierungsenergie und der Beweglichkeit bekräftigt. Die kleinere Beweglichkeit äußert sich dabei in einer größeren Aktivierungsenergie. Darüber hinaus kann der Ladungsträgergenerationsprozess auch von der Molekülstruktur abhängen. In dieser Arbeit wird untersucht, wie sich die Länge von Alkylseitenketten auf die Energieniveaus der Moleküle, aber auch auf die Absorptions- und Lumineszenzeigenschaften der Materialien in reinen und in Mischschichten mit dem Akzeptor C60 äußert. Die ermittelten Unterschiede bezüglich der Molekülordnung (geordneter für kürzere Seitenketten) und der Phasengrößen in Mischschichten (größere Phasen bei kürzerer Kettenlänge) werden in der Untersuchung der Temperaturabhängigkeit der Lebensdauer von Triplettexzitonen mittels PIA-Messungen bestätigt. Für Solarzellen ist von Bedeutung, ob sich die Seitenkettenlänge auf die Wechselwirkung zwischen D und A auswirkt. Der vermutete Zusammenhang wird hier nicht bestätigt. Ein ähnlicher Photostrom für alle untersuchten Verbindungen in Solarzellen mit planaren Heteroübergängen unterstreicht diese Schlussfolgerung. Unterschiede im Wirkungsgrad werden auf Änderungen der Energieniveaus und die Morphologie in Mischschichtsolarzellen zurückgeführt. Des Weiteren wird in einer Machbarkeitsstudie der Einfluss des elektrischen Felds auf die Generationsausbeute freier Ladungsträger untersucht. Dafür werden halbtransparente Solarzellen verwendet, die es ermöglichen, PIA-Messungen in Transmissionsgeometrie durchzuführen. Als mögliche Erklärung für das Auftreten zweier Rekombinationskomponenten in der Analyse des Rekombinationsverhaltens der durch Licht erzeugten Ladungsträger werden eingefangene Ladungsträger und gebundene Ladungsträgerpaare an der D/A-Grenzfläche genannt. Das Mischverhalten von D und A kann durch ein Heizen des Substrates während des Verdampfungsprozesses eingestellt werden, was von entscheidender Bedeutung für eine weitere Steigerung des Wirkungsgrades ist. Für DCV4T:C60-Mischschichtsolarzellen wird jedoch eine Verschlechterung des Wirkungsgrads zu höheren Substrattemperaturen beobachtet. Durch optische Messungen und Methoden zur Schichtstrukturbestimmung wird dieser Effekt auf eine Umordnung der DCV4T-Kristallite für hohe Substrattemperaturen und die damit verbundene Verringerung der Absorption und damit auch des Photostroms zurückgeführt. Bei einer Substrattemperatur von 90° C sind die D- und A-Komponenten fast vollständig entmischt. Dieses Beispiel ist von besonderer Bedeutung, weil hier die Ursachen für ein Verhalten aufgezeigt werden, das entgegen den Beispielen aus der Literatur eine Abnahme des Wirkungsgrads beim Aufdampfen der aktiven Schicht auf ein geheiztes Substrat zeigt. Schließlich werden die Optimierungsschritte dargelegt, mit denen Solarzellen mit einer DCV5T-Verbindung als Donatormaterial auf einen Rekordwirkungsgrad von 7,7% gebracht werden. Dabei wird die Substrattemperatur, die Dicke der aktiven Schicht und die Transportschichten angepasst.:Abstract - Kurzfassung Publications Contents 1 Introduction 2 Elementary Processes in Organic Semiconductors 2.1 Introduction 2.2 Optical Excitations in Organic Materials 2.2.1 Introduction 2.2.2 Radiative Processes: Absorption and Emission 2.2.3 Non-radiative Relaxation Processes 2.2.4 Triplet Excitons and Intersystem Crossing 2.3 Polarization Effects and Disorder 2.4 Transport Processes in Disordered Organic Materials 2.4.1 Charge Transport 2.4.1.1 The Bässler Model 2.4.1.2 Marcus Theory for Electron Transfer 2.4.1.3 Small Polaron Model 2.4.1.4 Functional Dependencies of the Charge Carrier Mobility 2.4.2 Diffusive Motion 2.4.3 Exciton Transfer Mechanisms 2.4.4 Characteristics of Exciton Diffusion 2.5 Charge Photogeneration in Pristine Materials 3 Organic Photovoltaics 3.1 General Introduction to Solar Cell Physics 3.2 Introduction to the Donor/Acceptor Heterojunction Concept 3.3 The Open-Circuit Voltage in Organic Solar Cells 3.4 Doping of Organic Semiconductors 3.5 Introduction to the p-i-n Concept 3.6 Charge Transfer Excitons in Donor/Acceptor Heterojunction Systems 3.6.1 Introduction 3.6.2 Verification of Charge Transfer Excitons in Donor/Acceptor Systems 3.7 The Process Cascade for Free Charge Carrier Generation in Donor/Acceptor Heterojunction Systems 3.7.1 The Initial Charge Transfer Step 3.7.2 The Binding Energy of the Charge Transfer Exciton 3.7.3 \"Hot\" Charge Transfer Exciton Dissociation 3.7.4 \"Cold\" Charge Transfer Exciton Dissociation 3.7.5 Supposed Influence Factors on Charge Transfer Exciton Dissociation 3.7.6 Recombination Pathways for Charge Transfer Excitons 3.7.7 Free Charge Carrier Formation and Recombination 4 Experimental Methods 4.1 Sample Preparation 4.2 Material Characterization Methods 4.2.1 Optical Characterization 4.2.2 Cyclic Voltammetry 4.2.3 Ultraviolet Photoelectron Spectroscopy 4.2.4 Atomic Force Microscopy 4.2.5 Grazing Incidence X-Ray Diffraction 4.2.6 Organic Field-Effect Transistor 4.3 Photoinduced Absorption Spectroscopy 4.3.1 Introduction 4.3.2 Derivation of the PIA Signal 4.3.3 Recombination Dynamics 4.3.4 Intensity Dependence of the PIA Signal 4.4 Solar Cell Characterization 4.4.1 External Quantum Efficiency 4.4.2 Spectral Mismatch Correction 4.4.3 Current-Voltage Characteristics 4.4.4 Optical Device Simulations 4.4.5 Optical Device Transmission Measurements 5 The Oligothiophene Material System 5.1 Introduction 5.2 Thermal Stability 5.3 Energy Levels 5.4 Optical Properties of the Pristine Materials 5.5 The Donor/Acceptor Couple: DCVnT and C60 5.6 Solar Cell Devices 5.7 Summary 6 Temperature Dependence of Charge Carrier Generation 6.1 Introduction 6.2 Principal Introduction to the PIA Measurements 6.2.1 Interpretation of the Spectra 6.2.2 Interpretation of the Frequency Scans 6.3 Temperature Dependence of the Spectra 6.4 Discussion of the Temperature Dependent Processes in the Blend Layer 6.5 Temperature Activated Free Charge Carrier Generation 6.5.1 Evaluation of the Activation Energy for the DCV4T-Me:C60 Blend 6.5.2 Comparison to a Sexithiophene Derivative (DCV6T-Me) 6.6 Summary 7 Side Chain Investigation on Quaterthiophene Derivatives 7.1 Energy Levels 7.2 Optical Properties 7.2.1 Solution and Pristine Films 7.2.2 Mixed Films with C60 7.3 Influence of the Side Chain Length on the Intermolecular Coupling 7.3.1 PIA Spectra of Pristine and Blend Layers at 10K 7.3.2 Recombination Analysis for Pristine and Blend Films at 10K 7.4 The Influence of the Side Chain Length on the Offset Charge Carrier Generation Rate at Low Temperature 7.5 In the High-Temperature Limit: Implications for Solar Cell Devices 7.5.1 PIA Spectra in Pristine and Blend Films at 200K 7.5.2 Recombination Analysis: Triplet Excitons and Free Charge Carriers 7.6 Solar Cells 7.6.1 Flat Heterojunction Devices 7.6.2 Bulk Heterojunction Devices 7.7 Summary 8 Electric-Field Dependent PIA Measurements on Complete Solar Cell Devices 8.1 Introduction 8.2 Semitransparent Organic Solar Cells 8.3 Photoinduced Absorption Measurements 8.4 Summary and Outlook 9 The Effect of Substrate Heating During Layer Deposition on the Performance of DCV4T:C60 BHJ Solar Cells 9.1 Introduction 9.2 The Importance of Morphology Control for BHJ Solar Cells 9.3 The Impact of Substrate Heating on DCV4T:C60 BHJ Solar Cells 9.4 Absorption and Photoluminescence 9.5 Topographical Investigations (AFM) 9.6 X-ray Investigations 9.6.1 1D GIXRD Measurements 9.6.2 2D GIXRD Measurements 9.7 Proposed Morphological Picture and Confirmation Measurements 9.7.1 Morphology Sketch of the DCV4T:C60 Blend Layer 9.7.2 Confirmation Measurements 9.8 The Equivalence of Temperature and Time 9.9 Summary 10 Record Solar Cells Using DCV5T-Me33 as Donor Material 10.1 Introduction 10.2 The Influence of the Substrate Temperature 10.3 Determination of the Optical Constants 10.4 Stack Optimization 10.5 Summary and Outlook 11 Conclusions and Outlook 11.1 Summary of the Photophysical Investigations 11.2 Summary of Device Investigations 11.3 Future Challenges Appendix A Detailed Description of the Experimental Setup for PIA Spectroscopy Appendix B Determination of the Triplet Level by Differential PL Measurements Appendix C Additional Tables and Figures Appendix D Reproducibility of the Solar Cell Results (Statistics) Appendix E Lists Bibliography Acknowledgments