Sveriges luftvärn står inför stora utmaningar vilka till stor del har orsakats av ett förändrat omvärldsläge med större osäkerheter. Osäkerheterna har i sin tur lett till att efterfrågan på förmågan luftvärn ökat och getts mer utrymme i samhällsdebatten. Konsekvensen av detta är att nya system ska införas, både på verkanssidan, bland ledningssystemen och bland sambandssystemen. Samtidigt ska en återaktiverad värnplikt implementeras och utgöra grunden för den framtida rekryteringen. Slutligen skall även de gamla systemen vidmakthållas med tillräckligt hög tillgänglighet, både gällande personal- och materieltillgång, så att de kan ingå i försvaret. Den beskrivna situationen innebär att ett avsevärt tekniksteg skall tas. Utmaningen denna studie fördjupar sig i behandlar organisationens förutsättningar att lyckas rekrytera tillräckligt många och tillräckligt duktiga ungdomar med förutsättningar att kunna underhålla denna teknik. Studien inriktas på värnpliktiga med tekniska befattningar och med en bakgrund i teknikinriktat studieförberedande gymnasieprogram. De är en eftertraktad kategori individer på den svenska arbetsmarknaden och många företag deltar i jakten på deras kompetens. Studien har genomförts kvalitativt genom djupintervjuer med individerna. Resultatet av empirin har sedan lett fram till slutsatserna att Försvarsmaktens marknadsföring inte träffar den beskrivna målgruppen. De individer vilka är avgörande för om organisationen kan klara sina uppgifter i framtiden känner endast vagt till Försvarsmakten och förknippar den inte med en teknisk yrkeskarriär. Samtidigt har det visat sig att den främsta påverkanskällan, deras föräldrar, är dåligt insatt i vad en fortsättning efter värnplikten kan innebära. Avgörande för hur den här kategorin individer väljer anställning är hur pass väl deras intressen och visioner passar in på det de uppfattat att Försvarsmakten erbjuder. Detta sammantaget skapar stora osäkerheter kring myndighetens förutsättningar att klara den framtida personalförsörjningen. Hur skall luftvärnet attrahera denna relativt lilla grupp med teknikintresserade ungdomar för att lyckas med en kraftig tillväxt och ett stort tekniksprång samt även behålla äldre materiel i drift? / The ground-based air defence of Sweden face some dire challenges in the near future. These have been caused by multiple converging reasons, the foremost of these being a change in the strategic situation in and around the Baltic Sea. This change has led to a publicly increased demand for army organic, ground based air defence capabilities. This in turn means that the government has ordered new systems to be introduced, both missile systems for intercepting airborne threats, new command and control systems and lastly, new communication systems. Parallel to the described shift in technology, recruitment through conscription has been rein­stalled. The last part of this complex situation is comprised of maintaining all of the legacy systems for use by the national defence forces. Taking such a large technological step raises demands of recruiting a large amount of techno­logically interested young people. The aim of this study is to broaden the understanding of Sweden’s ability to succeed with this endeavour. We have interviewed conscripts during their basic training to become mechanics and maintenance personnel at the Lv 6 regiment in Halm­stad. All our subjects have attended upper school and studied technology intended for pre­paring them for higher education. They are attractive to the general employment market and must be won in the battle for talent. This study has been designed using qualitative methods mainly comprised of individual inter­views. The results from these interviews have been analysed using an inspired by grounded theory approach. Our results have then been analysed a second time on an organisational level and compared to findings in the area of Employer branding. Our main findings are that marketing and informational campaigns, carried out by the Swe­dish armed forces aren’t aimed towards this category of young people. They have no prior experience of the armed forces and the messages sent out are not registered by our subjects. Our study indicates that the parents and closest family project a large amount of influence on these young people. Sadly, this category of influencers also lacks knowledge and information about the armed forces. The studied category of young people chooses their employers through how well their interests match with the perceived job offering. All of this taken in mind raises a question of the ability to succeed with recruitment goals for this category of youths.

In recent years, automotive engineering becomes more challenging and complex than previous years because of the innovation that transformed the cars powertrain system. By the quick developing of the automotive systems and increasing the consumer demand for Hybrid Vehicles (HV), Electric Vehicles (EV) and Autonomous cars, authenticity and security of engine systems are an essential part. The Hybrid Electric Vehicle structure contained several system sections like Electric Motor, Inverter, DC-DC Converter, etc. For testing this device, OEM’s are providing a special automotive standard norm (these norms are individually defining by automotive companies as LV124/123/148) which used for simulates variety of the electrical disturbances and monitoring the system behavior. This standard profile applies, simulates and records by EM Autowave system. Electrical tests have been done for a long time manually. Manual testing takes a huge amount of time, money and human resources. Based on the facts, the thesis purpose is to provide the automated system test for supporting test case execution on the HEV test bench, and offline classification independent of the test bench. This scope of the project will be developed by adapting automation library which is going to equip new features for automation system tool. On the other hand, in order to conform the test simulator and their communication system, a device file is implemented for loading and testing the electrical profiles on the test bench system. In addition, automated classification and evaluation used Matlab functions and the test result will be provided as plots which makes differential discovering very easier.

Orientador: Jose Sanches Mantovani / Resumo: Neste trabalho propõem-se metodologias para realizar o planejamento de sistemas de distribuição de energia elétrica de média tensão (MT), baixa tensão (BT) e o planejamento integrado de sistemas de média e baixa tensão (MT/BT). Nos modelos de funções objetivos considerados minimizam-se os custos associados à construção, expansão, operação e confiabilidade das redes de MT, BT e MT/BT, considerando a presença de geradores distribuídos e variáveis de natureza estocástica. A geração distribuída presente no planejamento de sistemas de distribuição é avaliada através de metodologias de geração de cenários e análise de risco. Como método de busca de soluções para o problema de planejamento dos sistemas de distribuição é proposta a meta-heurística de busca em vizinhança variável GVNS (General Variable Neighborhood Search). A meta-heurística GVNS trabalha com uma série de estruturas de vizinhanças que permitem explorar o espaço de busca de forma eficiente através dos critérios de diversificação e intensificação, aumentando a probabilidade de obter soluções que não sejam ótimos locais. No planejamento integrado MT/BT, as soluções obtidas são analisadas através de um fluxo de potência integrado entre as redes de MT e BT, considerando as relações de conexão dos transformadores entre estes sistemas. Os algoritmos propostos relacionados ao planejamento de sistemas MT, BT e MT/BT são implementados em linguagem de programação C++ e testado em diferentes sistemas testes de MT (54 barras e 182... (Resumo completo, clicar acesso eletrônico abaixo) / Doutor

Submitted by DIOGO RUPOLO null (rupolo.diogo@gmail.com) on 2017-09-08T14:50:14Z No. of bitstreams: 1 Tese Final Diogo Rupolo.pdf: 4125842 bytes, checksum: 60d451cc4d13afb90cca7e443d7436b1 (MD5) / Approved for entry into archive by Monique Sasaki (sayumi_sasaki@hotmail.com) on 2017-09-11T20:51:49Z (GMT) No. of bitstreams: 1 rupolo_d_dr_ilha.pdf: 4125842 bytes, checksum: 60d451cc4d13afb90cca7e443d7436b1 (MD5) / Made available in DSpace on 2017-09-11T20:51:49Z (GMT). No. of bitstreams: 1 rupolo_d_dr_ilha.pdf: 4125842 bytes, checksum: 60d451cc4d13afb90cca7e443d7436b1 (MD5) Previous issue date: 2017-08-18 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) / Neste trabalho propõem-se metodologias para realizar o planejamento de sistemas de distribuição de energia elétrica de média tensão (MT), baixa tensão (BT) e o planejamento integrado de sistemas de média e baixa tensão (MT/BT). Nos modelos de funções objetivos considerados minimizam-se os custos associados à construção, expansão, operação e confiabilidade das redes de MT, BT e MT/BT, considerando a presença de geradores distribuídos e variáveis de natureza estocástica. A geração distribuída presente no planejamento de sistemas de distribuição é avaliada através de metodologias de geração de cenários e análise de risco. Como método de busca de soluções para o problema de planejamento dos sistemas de distribuição é proposta a meta-heurística de busca em vizinhança variável GVNS (General Variable Neighborhood Search). A meta-heurística GVNS trabalha com uma série de estruturas de vizinhanças que permitem explorar o espaço de busca de forma eficiente através dos critérios de diversificação e intensificação, aumentando a probabilidade de obter soluções que não sejam ótimos locais. No planejamento integrado MT/BT, as soluções obtidas são analisadas através de um fluxo de potência integrado entre as redes de MT e BT, considerando as relações de conexão dos transformadores entre estes sistemas. Os algoritmos propostos relacionados ao planejamento de sistemas MT, BT e MT/BT são implementados em linguagem de programação C++ e testado em diferentes sistemas testes de MT (54 barras e 182 barras), BT (76 barras) e MT/BT (172 e 412 barras), sob diferentes cenários operacionais. / This work proposes methodologies for the planning of medium voltage (MV), low voltage (LV), and integrated planning of medium and low voltage (MV/LV) systems. In the objective function models are considered the costs associated with the construction, expansion, operation and reliability of MV, LV and integrated MV/LV networks. Distributed generators and stochastic variables are also considered in the models. The distributed generation present in the planning of distribution systems is evaluated through methodologies of scenario generation and risk analysis. As a method of finding solutions to the problem of distribution system planning, the GVNS metaheuristic (General Variable Neighborhood Search) is proposed. The metaheuristic GVNS works with a series of neighborhood structures that allow to explore the search space efficiently through diversification and intensification criteria, increasing the probability of obtaining solutions that are not local optimum. In integrated MV/LV planning, the solutions obtained are analyzed through an integrated power flow between the MV and LV networks, considering the connection ratios of the transformers between these systems. The proposed algorithms related to the planning of MV, LV and integrated MV/LV systems are implemented in C ++ programming language and tested in different distribution systems, MV (54 and 182 bus), LV (76 bus) and MV/LV (172 and 412 bus), under different operating scenarios.

Ο στόχος της διπλωματικής αυτής είναι η περιγραφή της αναδυόμενης τεχνολογίας PLC (PowerLine Communication). Η τεχνολογία αυτή με τη χρήση του πανταχού παρόντος ηλεκτρικού δικτύου προσφέρει ακόμα και σε απομακρυσμένους χρήστες πληθώρα ευρυζωνικών υπηρεσιών και πρόσβαση στο διαδίκτυο, αποτελώντας μια ανταγωνιστική επιλογή τρόπου επικοινωνίας. Για την κατανόηση της PLC τεχνολογίας αρχικά κρίνουμε απαραίτητη την λεπτομερή περιγραφή της δομής του ηλεκτρικού δικτύου, του εξοπλισμού που απαιτείται για την εφαρμογή της και των αρχιτεκτονικών της. Στη συνέχεια γίνεται αναφορά στα προβλήματα που παρουσιάζονται και χρήζουν αντιμετώπισης. Επιπρόσθετα, γίνεται σύντομη παρουσίαση των εναλλακτικών υπηρεσιών και σύγκριση των PLC με αυτές. Η μετάδοση μέσω ηλεκτροφόρων καλωδίων προσφέρει ένα μεγάλο εύρος ζώνης, παρέχοντας μία γκάμα πολυάριθμων υπηρεσιών, όπως το έξυπνο σπίτι ή το AMR (Automatic Meter Reading) για τη διευκόλυνση τόσο των οικιακών χρηστών όσο και των επιχειρησιακών. Η χρήση των γραμμών ηλεκτρικής ενέργειας ως τηλεπικοινωνιακό κανάλι απαιτεί την εφαρμογή των κατάλληλων τεχνικών πρόσβασης. Οι πιο διαδεδομένες τεχνικές είναι οι FDMA (Frequency Division Multiple Access), TDMA (Time Division Multiple Access) και CDMA (Code Division Multiple Access) . Η παρούσα διπλωματική επικεντρώθηκε στην TDMA και την FDMA με διαμόρφωση σήματος OFDM (Orthogonal Frequency Division Multiplexing) η οποία ονομάζεται OFDMA (Orthogonal Frequency Division Multiple Access). Πραγματοποιήθηκαν εξομοιώσεις σε Matlab διάφορων αλγορίθμων αναλογικής δικαιοσύνης με τεχνική OFDMA και ταυτόχρονη εξομοίωση της TDMA. Στόχος είναι να συγκρίνουμε τους αλγόριθμους αυτούς ως προς το συνολικό ρυθμό μετάδοσης και τη δικαιοσύνη κατανομής των πόρων στους χρήστες. Από τη σύγκριση αυτή προκύπτει ότι η τεχνική TDMA αποδίδει λιγότερο, ενώ από τους υπόλοιπους αλγόριθμους τα καλύτερα αποτελέσματα επιφέρει ο αλγόριθμος των Bill et al., με ισορροπία του συνολικού ρυθμού μετάδοσης και της επιθυμητής δικαιοσύνης. / Main goal of this diploma thesis is the description of the up and coming PLC (PowerLine Communication) technology. This technology offers access to the web and to several broadband services to even distant and isolated users, by exploiting the power line grid, widely spread to nearly all surface land sites, consisting this way a competitive communication alternative. For a better comprehension of the PLC technology, this work starts with a detailed description of the power line grid, the several PLC technology architectures and the necessary equipment for their application. Following this work, there is a reference to any possible problems that need to be overcome and a short comparative presentation of the PLC technology versus other alternatives to it. The data transmission over electricity lines offers a wide bandwidth and thus it may support a variety of applications, as the smart home and AMR (Automatic Meter Reading) for the proper service of either domestic or industrial users. The use of electricity power lines as a communication channel necessitates the application of multiple access Strategies as FDMA (Frequency Division Multiple Access), TDMA (Time Division Multiple Access) and CDMA (Code Division Multiple Access), which are currently the most popular. This thesis is focused on TDMA and FDMA with OFDM signal modulation. This technique is called OFDMA (Orthogonal Frequency Division Multiple Access). Several proportional rate constraints algorithms were simulated in Matlab applying both OFDMA and TDMA strategies in order to compare these algorithms in terms of the maximized total throughput and the fair allocation of resources to the end users (fairness). From this comparison it comes up that TDMA technique is less efficient, whereas from the other algorithms the most efficient is the one of Bill et al., that offers a good balance between total throughput and fairness.

Power losses are always a cause of worry for any power grid. In India, the situation is even worse. Though recent reports by Ministry of Power shows that Aggregate Technical and Commercial losses (AT &C losses) have come down from 36.64% in 2002-03 to 27% in 2011-12, yet they are much higher than the losses seen in many of the developed nations. The reduction shown in power loss is because of the Electricity Act, 2003 and the amendments made to it in 2007 which controlled the commercial losses rather than the technical losses. According to Ministry of Power, technical losses (Transmission & Distribution losses or T&D losses) in India are reported to be 23.65% in 2011-12. However, according to the study done by EPRI, for systems deployed in developed countries, these losses are estimated to be in the range of 7-15.5%. T & D losses occur in four system components namely step-up transformers and high voltage transmission (0.5-1%), step down to in intermediate voltage, transmission and step down to sub transmission voltage level (1.5-3%), sub-transmission system and step down to low voltage for distribution (2-4.5%), and distribution lines (3-7%). 1% of power loss is approximately equivalent to annual loss of Rs 600 million for a single state. Hence, in a year, loss in distribution line alone causes approximate loss of Rs 1.8-4.2 billion per state. Understanding and reducing power losses in distribution lines which contribute nearly 50% of the total T&D losses assume significance and has formed the motivation for the work reported in the thesis. In recent years, the trend has been to encourage users to generate solar power predominantly at residential complexes and captive power plants at industrial complexes. It has been suggested in the literature that Distributed Generation (DG) can not only reduce the load demanded from the power grid but also the power loss. In this thesis, it has been shown that by the choice of proper size and location of DG, the power loss can be reduced substantially as compared to unplanned deployment of DGs. The objective of the thesis is to design strategy for location of distributed user generated power to maximize the reduction in power loss. The thesis begins with a study of distributed generation in primary distribution networks and proceeds to problem formulation, with the aim being to develop an algorithm that can find out the optimal locations for DG allocation in a network. A greedy approximation algorithm, named OPLODER (i.e. Optimal Locations for Distributed Energy Resources), is proposed for the same and its performance on a benchmark data set is observed, which is found to be satisfactory. The thesis then moves on to describe the actual data of 101,881 commercial, residential and industrial consumers of Bangalore metropolitan area. A loss model is discussed and is used to calculate the line losses in LV part of the grid and loss is estimated for the said actual data. The detailed analysis of the losses in the distribution network shows that in most cases the losses are correlated with the sanctioned load. However there are also some outliers indicating otherwise. The analysis concludes that the distributed generated sources need to be optimally located in order to benefit fully. Also presented thereafter is a study about the impact of electrical properties and the structure of the network on power loss. In the second part of the thesis, OPLODER was again used to process the BESCOM data of 101,881 consumers by modeling them to be connected in three topologies namely Bus (i.e. linear structure), Star (i.e. directly connected) and Hybrid (i.e. tree structure). In case of Bus topology, when DG capacity available is 5% of the demand in substation, OPLODER reduced the loss from 14.65% to 10.75%, from 11.63% to 7.71% and from 13.33% to 9.24% for IISc, Brindavan, and Gokula substations respectively. Similarly, for the same amount of DG in case of star topology, OPLODER reduced loss from 1.75% to 1.26%, from 3.39% to 2.59% and from 2.96% to 1.99% for IISc, Brindavan, and Gokula substations respectively. Thereafter, the available real world data is re-modeled as a tree-type structure which is closer to the real world distribution network and OPLODER is run on it. The results obtained are similar to those presented above and are highly encouraging. When applied to the three substations viz. IISc, Brindavan and Gokula, the power loss dips from 9.95% to 7.42%, from 6.01% to 4.44% and from 8.07% to 5.95%, in case of DG used is 5% of the demand in substation. For the optimal strategies worked out in the thesis, additional overheads will be present. These overheads are studied and it has been found that the present infrastructure and technologies will be sufficient to handle the smart distribution network and the optimal strategy for distributed sources.

La pathologie pulmonaire et la pathologie cardiaque interagissent et le bloc “Cœur- poumon” est à considérer comme une seule et même entité en imagerie: la lecture du cœur, des vaisseaux, des poumons et du médiastin doit être globale et intégrée, quelle que soit la modalité d’imagerie. Nous avons pu ainsi illustrer la contribution de la TDM dans l’évaluation de la prévalence de la pathologie coronarienne asymptomatique au cours de la fibrose pulmonaire idiopathique, l’analyse du volume de l’oreillette gauche au cours des BPCO, la corrélation entre volume pulmonaire hypoperfusé et le rapport VD/VG, et l’évaluation de l’envahissement cardiaque au cours des néoplasies pulmonaires. Les avancées techniques en scannographie nous permettent désormais d’approcher outre la morphologie le versant fonctionnel, notamment par l’évaluation de la fonction cardiaque, de la perfusion pulmonaire, en attendant le développement en routine clinique de l’approche par TDM de la fonction de ventilation. Notre thèse avait pour ambition de contribuer modestement à la promotion d’une approche morphologique et fonctionnelle intégrée de l’imagerie du cœur, des vaisseaux thoraciques et du poumon, dont les bénéfices cliniques nous apparaissent quotidiens et dont l’enseignement nous apparait indissociable. / Pulmonary and cardiac pathology interact and the « heart-lung » bloc is to consider as one and same entity in imaging: heart, vessels, lungs and mediastinum analysis must be global and integrated, whatever imaging modality.In this work, we have illustrated computed tomography contribution in: evaluating asymptomatic coronary disease in cystic fibrosis pathology, left atrial volume in COPD patients, correlation of hypo perfused lung volume and RV/LV ratio, and cardiac invasion evaluation in broncho-pulmonary neoplasm.Computed tomography technological advances allow us to evaluate morphology and functional side, in evaluating cardiac function, pulmonary perfusion, waiting for the development of pulmonary ventilation in routine. Our work contributes to the development of a morphological and functional approach in heart, great vessels and lung imaging.

Thesis focuses on the basic characteristics of plasma, problems about origin of electrode spots and electrodynamics force acts on the electric arc. In the practical part was realized and produced model of a LV quenching system. Using optical diagnostics was received necessary data to analyze the movement of the electrode spots. The movements of the electrode spots were analyzed in terms of value RMS current passing through the electric arc, value of absolute pressure model in the LV quenching system and distance from each electrode.

The increase in electric vehicles and photovoltaic power production may introduce problems to the low-voltage distribution grid. With a higher number of electric vehicles, their accumulated charging power might breach the lowest allowed voltage level of the grid. Photovoltaic-modules can on the other hand exceed the highest allowed voltage level, by producing high accumulated power when the solar irradiance is high. Normally, electric distribution companies in Sweden reinforce the existing grid with more resilient infrastructure, such as stronger and larger cables or transformer stations. This is however a costly and time-consuming solution, which could be solved by using alternative means such as already existing resources. This Master's Thesis investigates how smart charging of batteries can support the low-voltage electrical grid with the increase in electric vehicles and photovoltaic power production. To do this, an optimization tool has been developed in Matlab. An existing model of a low-voltage grid is combined with the developed tool, where controllable batteries and photovoltaic-modules can be placed at specific households in the grid. The controllable batteries belong to either electric vehicles or stationary battery systems, and are intended to support the grid by the means of either reducing peak load powers, voltage variations, or a trade-off between them. Furthermore, this thesis investigates the maximum electric vehicle capability for a specific low-voltage electrical grid in Sweden. From the results, it can be concluded that smart charging of batteries can reduce the peak loads as well as voltage variations. The reduction of voltage variations for the entire low-voltage grid is greatest during the summer, when photovoltaic production generally is at its highest. The results also show that a stationary battery system can reduce the voltage variations to a greater extent, compared to an electric vehicle. Also, the introduction of multiple controllable batteries allows further support of the low-voltage grid. Regarding the maximum electric vehicle capability, the results show that the placement of the vehicles and the charging power strongly affect the maximum number of electric vehicles the low-voltage grid can manage. / Ökningen av elbilar och elproduktion från solceller kan ge problem i lågspänningsnätet. Med ett ökat antal elbilar kan den sammanlagrade effekten vid laddning underskrida den minsta tillåtna spänningsnivån i nätet. Solpaneler kan däremot leda till att den högsta tillåtna spänningsnivån överskrids, genom att producera en hög sammanlagrad effekt när solstrålningen är som högst. Vanligtvis förstärker elnätsbolag i Sverige det befintliga nätet med motståndskraftigare infrastruktur, såsom kraftigare och större kablar eller transformatorstationer. Detta är dock en kostsam och tidskrävande lösning, som skulle kunna lösas med alternativa medel, till exempel redan existerande resurser. Detta examensarbete undersöker hur smart laddning av batterier kan ge stöd till lågspänningsnätet, med en ökning av elbilar samt solcellsproduktion. För att undersöka detta har ett optimeringsverktyg utvecklats i Matlab. En befintlig modell av ett lågspänningsnät har kombinerats med det utvecklade optimeringsverktyget, där styrbara batterier samt solcellsproduktion kan placeras vid specifika hushåll i elnätet. De styrbara batterierna är antingen elbilar eller stationära batterisystem, och är ämnade till att stödja lågspänningsnätet genom att antingen reducera effekttoppar, spänningsvariationer eller en kompromiss av båda. Vidare undersöker detta examensarbete det maximala antalet elbilar som ett specifikt lågspänningsnät i Sverige kan hantera. Resultaten visar att smart laddning av batterier kan reducera effekttoppar samt spänningsvariationer. Reduceringen av spänningsvariationerna för hela lågspänningsnätet visar sig vara högst under sommaren, vilket är då solcellsproduktionen generellt är som högst. Resultaten visar även att stationära batterisystem kan reducera spänningsvariationer ytterligare, jämfört med en elbil. Att introducera flera styrbara batterier tillåter ett ännu större stöd till lågspänningsnätet. Angående det maximala antalet av elbilar som ett lågspänningsnät kan hantera visade resultaten att placeringen av elbilarna samt laddningseffekten har en stor påverkan.

El món de les comunicacions per la xarxa elèctrica (CXE) pot ser dividit en tres grans tipus: CXE en baix voltatge (CXE-BV), en mig voltatge (CXE-MV) i en alt voltatge (CXE-AV). En aquests últims anys, les CXE-BV han atret una gran expectació, ja que les seves capacitats han fet d'aquesta tecnologia una bona opció com alternativa pel bucle local d'accés i pel desplegament de xarxes d'àrea local, focalitzades aquestes últimes en l'entorn domèstic. A més, les CXE-BV inclouen un conjunt d'aplicacions de baixa velocitat orientades a l'operador, com la lectura automàtica de comptadors (LAC), distribució de càrrega, facturació dinàmica, etc. Per altra banda, les CXE-MV i CXE-AV, històricament lligades a tasques de telecontrol i teleprotecció, s'estan començant a considerar com un canal de comunicacions eficient i fiable. El desenvolupament de sistemes digitals i els esforços d'estandardització estan fent d'aquests canals un medi atractiu per a que els operadors elèctrics ofereixin serveis de comunicacions, ja que no necessiten invertir en infraestructura perquè la xarxa elèctrica ja està desplegada.En aquesta Tesi s'introduiran i es comentaran les particularitats de les tres xarxes elèctriques, després, es mostraran al lector les solucions tecnològiques existents pels canals de BV basats en la norma Europea CENELEC així com pels canals d'AV, mostrant que els sistemes actuals de LAC ofereixen una diversitat freqüencial molt baixa i que els mòdems CXE-AV estan ancorats en estendards antiquats.Aquest treball es mou per les tres topologies de la xarxa, particularment, en aplicacions orientades a la banda CENELEC, en mesura i modelat de canal, i en mesura i disseny del nivell físic per sistemes CXE-BV, CXE-MV i CXE-AV respectivament. Els sistemes actuals que exploten la banda CENELEC ofereixen mecanismes d'explotació de la diversitat freqüencial del canal molt limitats o nuls, donant lloc a una baixa robustesa en front a interferències i soroll de fons acolorit. Aquest treball proposa un esquema de modulació multiportadora que, mantenint una complexitat baixa, ofereix unes altes prestacions permetent un bon nivell d'explotació de la selectivitat freqüencial. Per al que a CXE-MV respecta, aquesta Tesi desenvolupa un model de canal determinístic-estadístic pels anells urbans de distribució de potència i, finalment, en sistemes CXE-AV, aquest treball proposa, basat en mesures de canal i proves de camp, un nivell físic de banda ampla capaç de incrementar la velocitat de comunicació mentre manté una baixa densitat espectral de potència limitant així la interferència a altres sistemes.PARAULES CLAU: Power line communications (PLC), low voltage (LV), medium voltage (MV), high voltage (HV), automatic meter reading (AMR), orthogonal frequency division multiplexing (OFDM), multicarrier spread spectrum (MC-SS), communication system design, channel measurements, channel modeling, scattering parameters. / El mundo de las comunicaciones por la red eléctrica (CRE) puede ser dividido en tres grandes tipos: CRE en bajo voltaje (CRE-BV), en medio voltaje (CRE-MV) y en alto voltaje (CRE-AV). En estos últimos años, las CRE-BV han atraído una gran expectación, ya que sus capacidades han hecho de esta tecnología una buena opción como alternativa para el bucle local de acceso y para el despliegue de redes de área local, focalizadas estas últimas en el entorno doméstico. Además, las CRE-BV incluyen un conjunto de aplicaciones de baja velocidad orientadas al operador como la lectura automática de contadores (LAC), distribución de carga, facturación dinámica, etc. Por otro lado, las CRE-MV y CRE-AV, históricamente ligadas a tareas de telecontrol y teleprotección, se están empezando a considerar como un canal de comunicaciones eficiente y fiable. El desarrollo de sistemas digitales y los esfuerzos de estandarización están haciendo de estos canales un medio atractivo para que los operadores eléctricos ofrezcan servicios de comunicaciones, ya que no necesitan invertir en infraestructura porque la red eléctrica ya está desplegada.En esta Tesis se introducirán y se comentarán las particularidades de las tres redes eléctricas, luego, se mostrarán al lector las soluciones tecnológicas existentes para los canales de BV basados en la norma Europea CENELEC así como para los canales de AV, mostrando que los sistemas actuales de LAC ofrecen una diversidad frecuencial muy baja y que los módems CRE-AV están anclados en estándares anticuados.Este trabajo se mueve por las tres topologías de red, particularmente, en aplicaciones orientadas a la banda CENELEC, en medida y modelado de canal, y en medida y diseño del nivel físico para sistemas CRE-BV, CRE-MV y CRE-AV respectivamente. Los sistemas actuales que explotan la banda CENELEC ofrecen mecanismos de explotación de la diversidad frecuencial del canal muy limitados o nulos, dando lugar a una escasa robustez frente a interferencias y ruido de fondo coloreado. Este trabajo propone un esquema de modulación multiportadora que, manteniendo una complejidad baja, ofrece unas altas prestaciones permitiendo un buen nivel de explotación de la selectividad frecuencial. Por lo que a CRE-MV respecta, esta Tesis desarrolla un modelo de canal determinístico-estadístico para los anillos urbanos de distribución de potencia y, finalmente, en sistemas de CRE-AV, este trabajo propone, basado en medidas de canal y pruebas de campo, un nivel físico de banda ancha capaz de incrementar la velocidad de comunicación mientras mantiene una baja densidad espectral de potencia limitando así la interferencia a otros sistemas.PALABRAS CLAVE: Power line communications (PLC), low voltage (LV), medium voltage (MV), high voltage (HV), automatic meter reading (AMR), orthogonal frequency division multiplexing (OFDM), multicarrier spread spectrum (MC-SS), communication system design, channel measurements, channel modeling, scattering parameters. / The world of Power line communications (PLC) can be divided into three main types: low voltage PLC (LV-PLC), medium voltage PLC (MV-PLC) and high voltage PLC (HV-PLC). These last years, LV-PLC has attracted a great expectation since its wideband capabilities has made this technology a suitable choice for last-mile access and in-home communications. Moreover, LV-PLC also includes a utility oriented low frequency and low speed applications, such as automatic meter reading (AMR), load distribution, dynamic billing and so on. On the other hand, MV-PLC and HV-PLC, historically oriented to teleprotection and telecontrol tasks, are being considered as a reliable communication channel. The development of digital equipment and the standardization efforts are making those channels an attractive medium for electrical utilities telecommunications services, since the network, as well as in LV-PLC, is already deployed. In this PhD dissertation, the three different PLC topologies are reviewed and the different communications techniques in such channels exposed. Then, a deep technological review of existing AMR solutions for the European CENELEC band, as well as HV-PLC systems is given, showing that existing AMR systems deliver low frequency diversity and HV-PLC systems are anchored in old fashioned standards.This work walks around the three topologies, specifically, CENELEC band utility oriented applications, channel measurement and modeling and channel measurement and physical layer design, regarding LV-PLC, MV-PLC and HV-PLC respectively. Existing CENELEC compliant systems deliver low or none frequency diversity mechanisms, yielding in a low robustness against colored noise and interference. This work propose a multicarrier based physical layer approach that, while keeping the complexity low, delivers high performance allowing a great level of frequency diversity. Focusing on MV-PLC, a hybrid deterministic-statistical channel model for urban underground rings is developed and, finally, in HV-PLC systems, this work proposes, based on measurements and field tests, a wideband physical layer in order to increase data rate while keeping low both the power spectral density and possible interference to other systems.KEYWORDS: Power line communications (PLC), low voltage (LV), medium voltage (MV), high voltage (HV), automatic meter reading (AMR), orthogonal frequency division multiplexing (OFDM), multicarrier spread spectrum (MC-SS), communication system design, channel measurements, channel modeling, scattering parameters.