La thèse porte sur l’étude de la morphologie et des différentes propriétés thermiques, mécaniques et barrières à la vapeur d’eau des nanobiocomposites à base de poly acide lactique (pla). La première partie est consacrée au greffage de l’anhydride maléique (am) sur le poly acide lactique plagma et à la mise en oeuvre de nanobiocomposites pla/cloisites, plagma/cloisites et pla/plagma/cloisites en utilisant deux cloisites® différentes (c20a et c30b), préparés par voie fondue. Au travers des différentes techniques utilisées, les résultats révèlent que les nanobiocomposites pla/cloisites élaborés se caractérisent par une morphologie mixte intercalée-exfoliée. L’ensemble des échantillons élaborés indiquent une meilleure dispersion de la cloisite apolaire c20a en présence de l’anhydride maléique et la réagrégation de la cloisite polaire c30b et par conséquent, l’amélioration à la fois des propriétés mécaniques et barrières à la vapeur d’eau des nanobiocomposites à base de la c20a. La seconde partie traite l’influence des groupements fonctionnels d’oxyde de graphène synthetisé au laboratoire et de graphène fonctionnalisé époxy commercialisé et fournit par nanovia (france) sur la dispersion des nanofeuillets de graphène au sein de la matrice pla, en présence ou en absence du compatibilisant plagma. L’étude révèle que la présence du compatibilisant améliore la dispersion de deux nanocharges étudiées. Le maximum des performances rhéologiques indiquant la meilleure dispersion de la nanocharge est enregistré pour une faible quantité d’oxyde de graphène possédant plus de groupements fonctionnels contenant l’atome d’oxygène. Les propriétés thermiques et barrières ont été considérablement améliorées avec l’incorporation des deux nanocharges et en présence de l’agent compatibilisant plagma. L’étude montre aussi que les propriétés mécaniques en traction des nanobiocomposites à base de graphène fonctionnalisé époxy (gfe) ont été améliorées en présence du plagma. / The thesis focuses on the study of the morphology and thermal, mechanical and barrier properties of the nanobiocomposites based on poly lactic acid (pla). The first part is devoted to the grafting of maleic anhydride (ma) on the poly lactic acid plagma and the elaboration of the nanobiocomposites pla/cloisites, plagma/cloisites and pla/plagma/cloisitres using two different cloisites (c20a and c30b), prepared by melt intercalation and the characterization of the main properties. The results indicate that the pla/cloisites nanobiocomposites exhibit a mixed intercalated-exfoliated morphology. All the prepared samples showed an improvement in both thermal, mechanical and barrier properties in the presence of the nanofiller. All prepared samples show better dispersion of apolar cloisite (c20a) in the presence of maleic anhydride and reaggregation of the polar cloisite (c30b) and therefore, the improvement of both the mechanical and barrier properties of the nanobiocomposites based on c20a. The second section discusses the effect of the functional groups of graphene oxide synthetized in the laboratory and the graphene fonctionnalized epoxy marketed and supplied by nanovia (france) on the dispersion of the graphene nanofillers in the pla matrix. The study reveals that the presence of compatibilizer improves the dispersion of two studied nanofillers. Maximum rheological performance indicating better dispersion of the nanofiller is registered for a small amount of graphene oxide (og) with more functional groups containing oxygen atom. The thermal and barriers properties have been considerably improved with the incorporation of two nanofillers and in the presence of plagma compatibilizer. The study also shows that the tensile properties of the pla containing graphene functionalized epoxy (gfe) were improved in the presence of plagma.

Condensation of 2,3-dichloromaleic anhydride and o-phenylenediamine in refluxing toluene affords the three compounds 2,3-dichloro-N-o-C6H4(NH2)maleimide (1), N,N¢-o-C6H4-bis(2,3-dichloromaleimide) (2), and 2,3-dichloropyrrolo[1,2-a]benzimidazol-1-one (3), with compound 1 as the major product. Repeating the same reaction in the presence of added PTSA furnishes compound 3 as the major product. Treatment of 3 with methylthiol in the presence of pyridine affords monosulfide compounds 2-chloro-3-methylthiopyrrolo[1,2-a]benzimidazol-1-one (4) and and the disulfide derivatives 2,3-di(methylthio)pyrrolo[1,2-a]benzimidazol-1-one (5). The substitution of the first chlorine group in compound 3 occurs regioselectively at C-3 to produce compound 4, followed by replacement of the remaining chlorine group to furnish the disulfide compounds 5. The new compounds 1-5 have been isolated by column chromatography and characterized by IR, NMR, XRD, CV and etc.

Rhomboids are a family of intramembrane serine proteases that cleave transmembrane protein substrates within the lipid membrane. They are involved in a wide range of biological processes, including signal transduction, parasite invasion, bacterial quorum sensing and apoptosis. While previous X-ray crystal structures and functional studies have provided some detailed insights into the mechanism of intramembrane hydrolysis, it is still not clear how the transmembrane substrate can gain access into the active site from the lipid environment. While several modes of action have been suggested, one hypothesis proposes a lateral movement of the fifth transmembrane helix, causing a displacement that would allow transmembrane substrates to enter the rhomboid active site. A powerful method that has the potential to yield insights into rhomboid dynamics is solution NMR; however, the large size of rhomboid protease samples has complicated conventional methods typically used to assess protein structure and dynamics. ¹⁹F NMR could allow the study of rhomboid conformational dynamics by providing a simplified spectrum with high sensitivity to changes in local chemical environments. In this thesis various methods of ¹⁹F incorporation were evaluated for utility in studying rhomboid conformational dynamics, focusing on the GlpG rhomboid from E. coli. First, GlpG samples were prepared with ¹⁹F incorporated into tryptophan sidechains, and 1D ¹⁹F NMR spectra were acquired. While spectra with decent spectral dispersion were obtained, the assignment process was complicated by low signal-to-noise, and multiple changes in the spectrum introduced by the mutation. Chemoselective labelling of cysteine residues with probes containing a trifluoromethyl group was also investigated and found to give rise to well resolved ¹⁹F NMR spectra with promising characteristics. In addition, protocols for incorporation of trifluoromethyl-phenylalanine using unnatural amino acid incorporation at introduced amber codon sites were also explored, since one of the long-term goals of this work is to study ¹⁹F-labelled GlpG in its native lipid environment. For this purpose, some protocol development was also performed to introduce GlpG into lipid nanoparticles using styrene maleic acid co-block polymers. However, low expression yields of trifluoromethyl-phenylalanine-labelled GlpG and the large size of the lipid nanoparticles are not yet compatible with solution NMR. Nonetheless, this thesis lays the groundwork for further development of these samples to allow the future study of conformational exchange of GlpG in native lipid membranes.

The diploma thesis deals with the heterogeneous technique of preparation of grafted polypropylene g maleic anhydride (PP-g-MAH). The knowledge of the course of the reaction and its impact on the PP grafting process are summarized in the theoretical part. The preparation of the grafted PP was carried out in a fluidized polymerization reactor at 115 °C, speed of mixing 210 rpm, reaction time 60 min and pressure 6 bar. The amount of grafted MAH was monitored by using a MAH concentration 3 and 5 wt% and an initiator concentration 0.25; 0.5; 1; and 1.5 wt%. Modification efficiency was compared by using 3 types of PP with different particle morphology and specific surface area. By creating the theoretical model, the maximum surface concentration of MAH was calculated and compared with experimental data. Characterization of PP materials was performed by Electron Scanning Microscopy (SEM), Differential Scanning Calorimetry (DSC) and particle surface analysis by BET. Quantitative analysis of grafted MAH was determined by FTIR spectroscopy and acid-base titration.

Diplomová práce se zabývá roubováním maleinanhydridu a anhydridu kyseliny itakonové na kyselinu poly(mléčnou) (PLA). U modifikované kyseliny poly(mléčné) byla sledována závislost konverze monomerů na různých molárních poměrech monomer/iniciátor při teplotách 180°C a 200°C. Množství naroubovaného monomeru bylo stanovováno acidobazickou titrací a pomocí FT-IR spektroskopií. Vliv stupně naroubování na krystalinitu modifikované PLA byl zjišťován pomocí diferenční kompenzační kalorimetrie, DSC. Degradace PLA byla orientačně pozorována pomocí indexu toku taveniny, MFI.

The theoretical part describes the principles of the free-radical induced grafting and the influence of various parameters on the reactions course. The literature research summarizes the latest knowledge in the field of the reactive modification of polypropylene (PP), it is mainly focused on the PP modification using an unsaturated acid anhydrides. Theoretical part describes the various procedures and modification of technology in order to increase the grafting yield of maleation. The experimental part is determined by the influence of the stabilizers concentration, the peroxide structure, and the binary mixture of monomers on the grafting yield and the reaction course. In the first part, the critical stabilizers concentration was determined based on the experimentally obtained relationship between the grafting yield and the stabilizers concentration. A kinetic schema of grafting of MAH onto PP in the presence of stabilizers has been proposed and compared with the experimental results. The effect of the stabilizers on the extent of the undesirable b-scission was evaluated based on the melt flow rate (MFR) and the rheological curves of PP-g-MAH. In the second part, the effect of the peroxide structure and the concentration of reactants on the grafting yield of PP modification with MAH and itaconic anhydride (IAH) was observed. The initial grafting yield Rg has been experimentally determined and compared with a defined area of theoretical values of Rg. The extent of b-scission was significantly influenced by the structure and the concentration of peroxide, as shown by the results of MFR and the rheological curves of PP-g-MAH. The last part of the doctoral thesis is focused on the assessment of the combination of MAH and IAH as comonomers on the grafting yield. At first, the reference polymers were prepared using the solution polymerization of MAH, and IAH, and copolymerization of MAH with IAH. The reference polymers were analyzed by FTIR, DSC, WAXS to confirm the probable copolymerization of MAH and IAH. The dependence of the reaction enthalpy on the reaction time was observed using simulations of bulk polymerization of MAH, IAH and mixtures MAH and IAH "in situ" in isothermal calorimeter. PP was subsequently modified with a combination of MAH and IAH as comonomers in order to assess its effect on the grafting yield

Polymeric coatings are being used in a growing number of applications, contributing to protection against weather conditions and localized corrosion, reducing the friction and erosion wear on the substrate. In this study, various polypropylene (PP) coatings were applied onto steel substrates by compression molding. Chemical modification of PP has been performed to increase its adhesion to metallic surfaces by grafting of maleic anhydride (MAH) onto PP in the presence of dicumyl peroxide (DCP). Influence of different concentrations of MAH and DCP on the properties of resulting materials have been examined. The coated steel samples are characterized by scanning electron microscopy (SEM), shear adhesion testing, FTIR and tribometry. The coatings with 3 wt. % MAH have shown the maximum adhesion strength due to maximum amount of grafting. The wear rates increased with increasing the amount of MAH due to simultaneous increase in un-reacted MAH.

As a preliminary starting point for the present study, physical and mechanical properties of polypropylene nanocomposites (PPNCs) for samples received from Queen's University Belfast have been evaluated. Subsequently, polymer/clay nanocomposite material has been produced at Bradford. Mixing and processing routes have been explored, and mechanical properties for the different compounded samples have been studied. Clay intercalation structure has received particular attention to support the ultimate objective of optimising tensile and fracture behaviour of isotropic and die-drawn PPNCs. Solid-state molecular orientation has been introduced to PPNCs by the die-drawing process. Tensile stress-strain measurements with video-extensometry and tensile fracture of double edge-notched tensile specimens have been used to evaluate the Young¿s modulus at three different strain rates and the total work of fracture toughness at three different notch lengths. The polymer composite was analyzed by differential scanning calorimetry, thermogravimetric analysis, polarizing optical microscopy, wide angle x-ray diffraction, and transmission electron microscopy. 3% and 5% clay systems at various compatibilizer (PPMA) loadings were prepared by three different mixing routes for the isotropic sheets, produced by compression moulding, and tensile bars, produced by injection moulding process. Die-drawn oriented tensile bars were drawn to draw ratio of 2, 3 and 4. The results from the Queen's University Belfast samples showed a decrement in tensile strength at yield. This might be explained by poor bonding, which refers to poor dispersion. Voids that can be supported by intercalated PP/clay phases might be responsible for improvement of elongation at break. The use of PPMA and an intensive mixing regime with a two-step master batch process overcame the compatibility issue and achieved around 40% and 50% increase in modulus for 3% and 5% clay systems respectively. This improvement of the two systems was reduced after drawing to around 15% and 25% compared with drawn PP. The work of fracture is increased either by adding nanoclay or by drawing to low draw ratio, or both. At moderate and high draw ratios, PPNCs may undergo either an increase in the size of microvoids at low clay loading or coalescence of microvoids at high clay loading, eventually leading to an earlier failure than with neat PP. The adoption of PPMA loading using an appropriate mixing route and clay loading can create a balance between the PPMA stiffness effect and the degree of bonding between clay particles and isotropic or oriented polymer molecules. Spherulites size, d-spacing of silicate layers, and nanoparticles distribution of intercalated microtactoids with possible semi-exfoliated particles have been suggested to optimize the final PPNCs property. / SABIC

<p>Maleation is a common means of modification for many commodity polymers and is used to several ends. In this study, various waxes were functionalized with maleic anhydride through several maleation processes, with the end goal of obtaining a cost effective processes to make emulsifiers to be used in emulsions that impart water-resistance to building products, such as gypsum wallboards. Research was done in collaboration with an industrial partner, in order to replace commercially available emulsifiers currently being used in their processes with a less costly product that could easily be made on-site based on their consumption requirements, through a solvent-free approach. Reactions involving both the free-radical initiated maleation of paraffin waxes and thermal addition of maleic anhydride to alpha-olefins were examined extensively. It was found that emulsions with properties matching or exceeding those of control emulsion formulations were obtainable using experimental emulsifiers made through both maleation methods. When used in gypsum wallboards, emulsifiers made through thermal maleation showed levels of water-repellency that matched or exceeded those of control formulations at lower loading levels, while emulsifiers made through free-radical maleation were subject to performance issues.</p> / Master of Applied Science (MASc)

High molecular weight star-shaped polystyrenes were prepared via the coupling of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) terminated polystyrene oligomers with divinylbenzene (DVB) in m-xylene at 138 °C. Linear polystyrene oligomers (Mn = 19,300 g/mol, Mw/Mn = 1.10) were synthesized in bulk styrene using benzoyl peroxide in the presence of TEMPO at approximately 130 °C. In situ mid-infrared spectroscopy was successfully utilized to follow initiation, monomer conversion, and polymer formation. Real-time data allowed for the determination of apparent rate constants of 2.1E-5 s⁻¹ at 132 °C and 1.2E-5 s⁻¹ at 126 °C from the profile of the decaying styrene vinyl carbon-hydrogen (=CH₂) absorbance at 907 cm⁻¹. Coupling of the TEMPO terminated oligomers under optimum conditions resulted in a compact and dense product with a number average molecular weight exceeding 300,000 g/mol (Mw/Mn = 3.03) after 24 h, suggesting the formation of relatively well-defined star-shaped polymers. Synthetic factors that affected the molecular weight, yield, and composition of maleic anhydride (MAH), norbornene (Nb), and tert-butyl 5-norbornene-2-carboxylate (NbTBE) terpolymers were investigated. Pseudo first order kinetic analysis using in situ FTIR indicated that the observed rate of reaction was a strong function of the Nb/NbTBE ratio with a maximum of 6.7E-5 s⁻¹ for a 50/0/50 Nb/NbTBE/MAH monomer ratio and a minimum of 1.1E-5 s⁻¹ for a 0/50/50 Nb/NbTBE/MAH ratio. Polymer yields were also observed to be a function of the Nb/NbTBE ratio and also decreased with increasing NbTBE. Calculated work of adhesion values (Wadh) values were observed to increase as the content of NbTBE was increased. 193 nm photoresist formulations incorporating polymers with high NbTBE content showed increased imaging performance using 193 nm light and successfully produced sharp and defined features as small as 110 nm, which was demonstrated via scanning electron microscopy (SEM). Additional functionality was introduced via the copolymerization of MAH with several norbornene (Nb) derivatives that were synthesized from facile Diels-Alder cycloaddition reactions of cyclopentadiene with a-olefins containing electron withdrawing groups. Subsequent hydrolysis of the anhydride offered further versatility and provided an avenue to introduce aqueous base solubility into Nb/MAH copolymers. / Ph. D.