Thesis (M.S.)--University of Wisconsin--Madison, 1970. / eContent provider-neutral record in process. Description based on print version record. Includes bibliographical references.

"Tautologically, castability is a critical requirement in any casting process. The two most important factors impacting castability are the susceptibility of a metal to hot tearing and the degree of casting fluidity a material possesses. This work concerns itself with fluidity of molten metal. Since experimental investigations into casting fluidity began, researchers have sought to maximize fluidity through superheat, mold temperature, alloy chemistry, melt cleanliness, and mold design. Researchers who have examined the published results in the field have remarked on the difficulty of making quantitative comparisons and drawing conclusions from the data. Ragone developed a horizontal vacuum fluidity apparatus and an analytical expression for fluid length to help resolve these issues. This was expanded on by Flemings et al. Still, the comparison of results is complicated by experimental uncertainties and a plurality of experimental procedures. This work seeks to resolve these issues through an analysis of experimental uncertainties present in existing fluidity tests and the development of an improved test and procedure which is very precise, accurate, and reliable. Certain existing tests and software packages have been shown to be unsuitable for quantitative fluidity measurement. Expressions for experimental uncertainty in fluidity testing have been derived. The capability to predict variations in fluidity as a function of alloy chemistry and other variables whose range of values are intrinsic to the economics of the process will help to more accurately determine the superheat needed for successful castings and will in turn lead to a decrease in scrap rates. This will enable metal casters to more reliably cast thin sections, and to reduce cycle time or scrap rate to achieve productivity goals. Superheat was shown to remain the dominant factor in fluidity, but the test allowed investigation of alloy modifications within an alloy specification in this alloy system. Factors known to have negative effects on structural properties were found often to have neutral or positive impacts on fluidity. A deep understanding of variations in fluidity measurements is the next necessary step in a century-long quest to understand how best to make metal castings through the use of fluidity experiments."

"Semi-solid metal (SSM) processing has emerged as a preferred manufacturing method due to the superior quality associated with semi-solid castings. In recent years, the driving force to reduce process cost has led to the development of a few rheocasting (also termed slurry-on-demand) processes. These include UBE’s New Rheocasting (NRC) process [1], Idra Prince’s Semi-Solid Rheocasting (SSR) process [2], and THT’s Sub-Liquidus Casting (SLC®) process [3]. A novel slurry-making SSM process developed at ACRC/MPI, termed the “Continuous Rheoconversion Process” (CRP), is a passive liquid mixing technique in which the nucleation and growth of the primary phase are controlled using a specially designed “reactor”. The reactor provides heat extraction, copious nucleation and forced convection during the initial stage of solidification, leading to the formation of thixotropic structures. In these studies, the critical issues/challenges to optimize the CRP for industrial applications have been addressed through validation experiments and pre-industrial trials."

No description available.

Thesis (D. Tech. ( Mechanical Engineering )) - Central University of technology, Free State, 2012 / In this study an alternative indirect Rapid Tooling process is proposed. It essentially consists of producing sand moulds by Additive Manufacturing (AM) processes followed by casting of tools in the moulds. Various features of this tool making method have been investigated. A process chain for the proposed tool manufacturing method was conceptually developed. This process chain referred to as Rapid Casting for Tooling (RCT) is made up of five steps including Computer Aided Design (CAD) modeling, casting simulation, AM of moulds, metal casting and finishing operations. A validation stage is also provided to determine the suitability of the tool geometry and material for RCT. The theoretical assessment of the RCT process chain indicated that it has potential benefits such as short manufacturing time, low manufacturing cost and good quality of tools in terms of surface finish and dimensional accuracy. Focusing on the step of AM of the sand moulds, the selection of available AM processes between the Laser Sintering (LS) using an EOSINT S 700 machine and Three Dimensional Printing using a Z-Corporation Spectrum 550 printer was addressed by means of the Analytic Hierarchy Process (AHP). The criteria considered at this stage were manufacturing time, manufacturing cost, surface finish and dimensional accuracy. LS was found to be the most suitable for RCT compared to Three Dimensional Printing. The overall preferences for these two alternatives were respectively calculated at 73% and 27%. LS was then used as the default AM process of sand moulds in the present research work. A practical implementation of RCT to the manufacturing of foundry tooling used a case study provided by a local foundry. It consisted of the production of a sand casting pattern in cast iron for a high pressure moulding machine. The investigation confirmed the feasibility of RCT for producing foundry tools. In addition it demonstrated the crucial role of casting simulation in the prevention of casting defects and the prediction of tool properties. The challenges of RCT were found to be exogenous mainly related to workmanship. An assessment of RCT manufacturing time and cost was conducted using the case study above mentioned as well as an additional one dealing with the manufacturing of an aluminium die for the production of lost wax patterns. Durations and prices of RCT steps were carefully recorded and aggregated. The results indicated that the AM of moulds was the rate determining and cost driving step of RCT if procurement of technology was considered to be a sunk cost. Overall RCT was found to be faster but more expensive than machining and investment casting. Modern surface analyses and scanning techniques were used to assess the quality of RCT tools in terms of surface finish and dimensional accuracy. The best surface finish obtained for the cast dies had Ra and Rz respectively equal to 3.23 μm and 11.38 μm. In terms of dimensional accuracy, 82% of cast die points coincided with die Computer Aided Design (CAD) data which is within the typical tolerances of sand cast products. The investigation also showed that mould coating contributed slightly to the improvement of the cast tool surface finish. Finally this study also found that the additive manufacturing of the sand mould was the chief factor responsible for the loss of dimensional accuracy. Because of the above, it was concluded that light machining will always be required to improve the surface finish and the dimensional accuracy of cast tools. Durability was the last characteristic of RCT tools to be assessed. This property was empirically inferred from the mechanical properties and metallographic analysis of castings. Merit of durability figures of 0.048 to 0.152 were obtained for the cast tools. It was found that tools obtained from Direct Croning (DC) moulds have merit of durability figures three times higher than the tools produced from Z-Cast moulds thus a better resistance to abrasion wear of the former tools compared to the latter.

"New, economical semi-solid metal (SSM) processes rely on forced convection during solidification to influence non-dendritic growth. The fundamental mechanisms that produce SSM microstructures in the presence of forced convection (due to fluid flow) are not fully understood. The objective of this work is to elucidate these mechanisms through the use of a new semi-solid slurry-making technique. Employing an apparatus developed at WPI, two alloy melts are mixed within a static reactor that induces convection and rapid cooling. Experiments carried out with this apparatus, named the “Continuous Rheoconversion Process” (CRP), result in globular semi-solid microstructures throughout a wide range of processing conditions. These conditions include the superheat in the melts before mixing, cooling rate of the slurry through the SSM range, and the presence or absence of inoculants in the melts. The results comprise repeatable sets of semi-solid microstructures having fine particle size and shape factors approaching unity. Even in the absence of melt inoculants, uniform distributions of α-Al particle sizes of about 60µm are attainable. Entrapped liquid is not present in the majority of the samples obtained with the CRP, and irregular particles that form in the process are of a limited distribution. Variation of slurry analysis methods indicates that these structures can be obtained consistently for both thixocasting and rheocasting applications. The design of the mixing reactor leads to turbulent fluid flow just as solidification commences. The results suggest that the following factors must be considered in identifying the mechanisms operating under the above conditions: copious nucleation of the primary phase; dispersion of nuclei throughout the bulk liquid; and inhibited remelting of nuclei due to temperature uniformity. In the CRP, these factors consistently lead to suppression of dendritic growth, significant grain refinement, and globular slurries. The exact fundamental mechanism leading to this effect is yet to be uncovered; however it is clear that temperature gradients ahead of the liquid are such that a cellular, non-dendritic morphology is the most stable growth form. Through further exploration of the process and identification of the operating mechanisms, future development of economical, continuous rheocasting methods will be facilitated."

"This research investigated the relationship between T5 heat treatment and elongation in thixocast and rheocast SSM components as a means to reduce the energy, time, and cost associated with T6 treatments while still producing improved properties over the as-cast condition. Temperature and time were varied as a part of work to optimize aging conditions for SSM materials. Both conventional furnace and fluidized bed heat treatments were employed. Tensile bars were fabricated from the heat treated A356 components and were pulled. Extensive SEM and stereo microscopy were performed to examine the factors which produced favorable results in the T5 condition. Data generated for T6 and as-cast components were also collected for purposes of comparison. Quality index calculations were employed to help evaluate the results. Optimized procedures and aging parameters have been presented"

Thesis (MScEng (Industrial Engineering))--University of Stellenbosch, 2008. / This thesis forms part of the AMTS Project on Investment Casting Capabilities for Light Metal Alloys in South Africa, the focus area being Rapid Tooling Development. Various issues of the investment casting process are being discussed from an industrial engineering point of view. These issues are related to the possibilities of improving the investment casting process’ lead times by shortening it while still maintaining affordable costs and required quality. Hereby the possibilities given by the newly developed “rapid technologies” are investigated. The focus is on Rapid Pattern Making as one of the most essential components for accelerated development of new products. Three of the most widely used layer manufacturing processes available in South Africa are selected for the study, namely Three Dimensional Printing – Drop-on-Bed (ZCorporation), Selective Laser Sintering (EOS) and Three Dimensional Printing – Drop-on-Drop (ThermoJet - 3D Systems). These three methods represent different materials; therefore different mechanical properties, different process economics as well as different technological characteristics. A standard benchmark part is used as a study base. Four patterns are produced by these three methods. A comprehensive measurement programme is conducted, followed by an appropriate statistical analysis and evaluation regarding accuracy and surface finish. Rapid Die Making is analysed with the possibilities of using additive methods for rapid tooling. Two dies are built with the same technology – Selective Laser Sintering (EOS), but in different materials. The same evaluation methodology is used for the statistical analysis and comparison. The two dies are injected with wax in order to produce the original benchmark part. The best wax patterns from each die are selected and evaluated, using the same methodology for analysis and comparison. The current state of Direct Shell Production is shortly discussed. The research concludes that RP&T techniques can successfully be used for creating accurate patterns and dies in order to shorten lead times in the investment casting process chain. Each RP&T process has its own set of advantages and disadvantages. All users should evaluate their requirements and the capabilities of the variety of techniques before deciding on a process to apply.

M. Tech. (Department of Metallurgical Engineering, Faculty of Engineering and Technology), Vaal University of Technology. / The production of austenitic stainless-steel pump impellers in foundries present a huge challenge mainly due to its thin-walled blades, pouring temperature, presence of junctions and chemical composition. Two different alloys were used namely nodular cast iron and austenitic stainless-steel. Nodular cast iron was used as a comparison alloy due to its excellent flowability whereas austenitic stainless-steel was chosen due to its attractive corrosion and wear resistant properties. Austenitic stainless-steel alloy showed difficulties during casting because of its chemical composition and freezing range. Thin-walled sections are more susceptible to filling defects like misrun and cold-shut. This results in high scrap rate and high processing costs during high production of thin-walled components. High pouring temperature is considered one of the most effective methods to improve filling ability of thin-walled castings. However, there is a major drawback in using this method owing to the high occurrence of shrinkage defects and hot tearing especially at junctions. 1060 aluminium was used as a benchmark to evaluate the effect of wall thickness on the filling and feeding of thin-walled Al components with complex geometry during sand casting. The aim of this dissertation is therefore to optimize casting process of sand cast austenitic stainless-steel pump impeller. Numerical modelling and additive manufacturing were used to optimize the production of this product. The use of casting simulation software combined with three-dimensional (3D) mould printing technology has enabled optimisation of casting parameters to minimise the occurrence of casting defects. Casting parameters of five test samples of complex geometry and varying thicknesses (1.0 mm;1.5 mm;2 mm;2.5 mm and 3.0 mm) were optimised using MAGMAsoft® at a constant pouring temperature of 700 °C and 1060 Aluminium as an alloy. Simulation and casting results showed that complete filling was only possible at a wall thickness of 3 mm. The simulation results showed that as the wall thickness increased from 1 mm to 3 mm the filling ability increased by 67.5 % whereas experimental casting results showed that filling ability increase by 75 %. The combination of MAGMAsoft® simulation and 3D printed moulds proved to be effective tools in predicting filling and feeding of thin-walled aluminium components during sand casting. MAGMAsoft® casting software was used to simulate metal flow and predict the degree of filling at different pouring temperatures. Test samples were cast using 1060 Aluminium alloy at temperatures of 702 °C, 729 °C, 761 °C, 794 °C, 800 °C and 862 °C. Complete mould filling was predicted at 800 °C using the simulation model and 761°C during actual casting. At temperatures above 761°C tearing at the junction was quite pronounced. An optimal of 761°C pouring temperature was found to be appropriate pouring temperature when casting thin-walled aluminum components using sand casting. MAGMAsoft® casting software proved to be an effective tool in optimizing filling and feeding of thin-walled aluminium components during sand casting. Nodular cast iron pump impeller was optimized at 1500 °C using MAGMAsoft® and 3D mould printing technology. Design variables used were feeder radius (17 mm, 18 mm, 19 mm and 20 mm), feeder height (32 mm, 33 mm, 34 mm, 35 mm) and number of feeders of (3, 4 and 5). Simulation and casting results showed a completely-filled casting. The high fluidity of nodular cast iron promotes mould filling ability and prevent any form of misrun defect. Minimum shrinkage was noted at the junctions and top surface of the casting. A new design was proposed to eliminate shrinkage defects at the junctions of the nodular cast iron pump impeller. The design used a tapered circular runner bar with straight ingates. Optimization of nodular cast iron was now done at 1390 °C with the use of MAGMAsoft® and real casting was done 1385 °C. Simulation and casting were in correlation to each other since both showed completely-filled mould cavity with no misrun, cold-shut and shrinkage porosity defect. Simulation proved to be an effective tool in optimizing filling and solidification of nodular cast iron during sand casting. Austenitic stainless-steel pump impeller was optimized at 1500 °C using MAGMAsoft® and 3D mould printing technology. A high quality mould and core print were printed with the use of Voxeljet VX1000 at a minimum period of time. Design variables used were feeder radius (17 mm, 18 mm, 19 mm and 20 mm), feeder height (32 mm, 33 mm, 34 mm, 35 mm) and number of feeders of (3, 4 and 5). An increase in feeder size and the number of feeders greatly reduced hot spot and porosity of the casting but it also reduced the casting yield. The quality of the casting was found to be inversely proportional to the casting yield. Simulation showed a completely-filled casting with actual casting showing only 50 % filling ability. High viscosity of the molten metal and thin walled blades promote quick solidification which caused misrun defects. A new design was proposed to eliminate misrun defects of the first design. MAGMAsoft® was used to optimize this design at 1550 °C. The design used a tapered circular runner bar with tapered ingates. The actual casting showed improved filling ability from 50 % to 80 % while simulation showed completely-filled mould cavity (100 %). Major factors which contributed to low filling ability of austenitic stainless-steel pump impeller were chemistry, runner system and men. Numerical modelling and additive manufacturing did optimize filling and feeding of sand cast austenitic stainless-steel pump impeller.