Segmental chain dynamics in polymer blends is a very important topic, not only from a fundamental point of view but also from technological applications. Because of the difficulties in the commercialization of new polymers, industries have turned increasingly towards blending of polymers to optimise their end use (mechanical, rheological) properties. The design of tailor-made materials would be enormously facilitated by the understanding of the blending phenomena at a molecular level. The key question to address is to understand the dynamics of each component of the blend modified by blending? The thesis has systematically studied the effect of multiwalled carbon nanotubes on the chain dynamics, demixing temperature, structural properties and evolution of morphology in a classical miscible polymer blend system (PVDF/PMMA). The thesis comprises of six chapters, Chapter 1 is an introductory chapter that outlines the fundamentals of polymer blends, crystallisation in polymer blends and the basics of dielectric spectroscopy. As one of the rationales of this work is to systematic study whether phase separated in these blends can be used as a tool to develop membrane for water purification. This chapter also gives an overview of the reported studies of ultrafiltration membrane fabrication, factors affecting membrane morphology and flux. In Chapter 2, the materials and methodology used to carry out experiments and the experimental procedures are discussed. Chapter 3 discusses the effect of concentration of PMMA and amine functionalized multiwalled carbon nanotubes (MWNTs) on the crystallisation induced phase separation using FTIR, XRD, POM and shear rheology. Electron microscopy and selective etching confirmed the localisation of MWNTs in the PVDF phase of the blends. Blends with MWNTs facilitated in heterogeneous nucleation manifesting in an increase in crystallisation temperature. The crystallisation induced phase separation in PVDF/PMMA blends was observed to influence the interconnected network of MWNTs in the blends. Chapter 4 discuss the effect of concentration of PMMA and MWNTs on the miscibility and the segmental relaxations was probed in situ by DSC and dielectric relaxation spectroscopy (DRS). The dynamic heterogeneity in the blends as manifested by the presence of an extra relaxation at a higher frequency at or below the crystallisation induced phase separation temperature was also discussed. We found that PVDF/PMMA blend (PVDF ≥ 80 wt%) exhibits three distinct relaxations; αc corresponding to crystalline PVDF, αβ segmental relaxation of PMMA and αm of amorphous miscibility whereas all relaxations overlap and constitute a single broad relaxation in PVDF/PMMA blend (PVDF ≤ 70 wt%). This confirms that there is a certain composition width in this blend wherein three distinct relaxations can be traced. This could due to many reasons like the width of crystal-amorphous interphase in the crystal lamellae, crystal size and morphology is strongly contingent on the concentration of PMMA. Relaxations are not very distinct in presence of MWNTs due to defective spherulites that shift the relaxations towards a higher frequency. Chapter 5 has attempted to tune the microporous morphology of PVDF membranes using crystallisation induced phase separation in PVDF/PMMA blends. As PVDF/PMMA is a melt-miscible blend, the samples were allowed to crystallise and the amorphous PMMA phase, which isolates in the interlamellar or inter-spherulitic regions in the blends, was etched out to generate microporous structures. The pore sizes can be tuned by varying the PMMA concentration in the blends. We observed that 60/40 PVDF/PMMA blends showed larger pores as compared to 90/10 PVDF/PMMA blends. We further modified PVDF membranes by sputtering silver on the surface. The bacterial cell viability was distinctly suppressed (99 %) in silver sputtered membranes. The ICP analysis suggests that slow Ag+ ions release from the sputtered membrane surface assisted in developing antibacterial surface. Our findings open new avenues in designing water filtration membranes and also help in understanding the crystallisation kinetics for tuning pore size in membranes. Chapter 6 summarises the important results of this work. MWNTs act as hetero nucleating agent and specifically interact with PVDF thereby influences the dynamics of PVDF chains. MWNTs can also restrict the amorphous segmental mobility and can influence the intermolecular cooperativity and coupling. The crystallisation induced phase separation in various blends can result in various crystalline morphologies depending on the PVDF concentration. By selectively etching PMMA from the phase-separated blends, microporous morphology can be generated

L’objectif de cette thèse est de développer un matériau à base de polyméthacrylate de méthyle (PMMA) amorcé par une réaction redox à température ambiante pour produire des composites thermoplastiques. Plus particulièrement, notre travail a consisté à étudier le mécanisme d’amorçage afin d’améliorer la formulation de la résine en terme de cinétique de polymérisation. Afin d’atteindre cet objectif, les paramètres d’Arrhenius de la décomposition d’amorceur ont été déterminés et intégrés dans un modèle de simulation numérique décrivant la polymérisation du MMA à température ambiante développé à l’aide du logiciel PREDICI. Basé sur cette simulation, des différents paramètres ont été testés dans le but de diminuer le temps de polymérisation. En complément de la détermination des paramètres du système d’amorçage, une étude de copolymérisation avec un grand nombre de comonomères a été effectuée. Cette étude a conduit à l’identification d’un monomère permettant d’accélérer la vitesse de polymérisation : le méthacrylate d’acetoacetoxyethyle (AAEMA). Une étude cinétique de ce monomère a été réalisée avec l’identification du coefficient de la vitesse de propagation kp ainsi que les paramètres de copolymérisation avec MMA, rMMA et rAAEMA. Les paramètres cinétiques, qui ont été déterminés expérimentalement, ont été vérifiés par une simulation numérique de copolymérisation de MMA et AAEMA. / Composite materials are used for decades as high-performance materials in industry. Up to date these materials were based on non-recyclable thermoset polymers. Nowadays, environmental and economical restrictions enhance the development of recyclable composite materials. For answering that demand, research focuses on the development of recyclable thermoplastic polymer composites. Within this context, the work of this thesis focuses on the development of a material based on a poly(methyl methacrylate) (PMMA) resin initiated with a redox initiation system at room temperature in order to prepare thermoplastic composites. More precisely, our work consisted of studying this initiation system and to improve the kinetics of the resin formulation. For that purpose, the Arrhenius parameters of the initiator decomposition reaction were determined and implemented in a simulation model that describes the polymerization of MMA at room temperature. Based on the simulation carried out on the software PREDICI, several conditions were tested aiming in the decrease of the polymerization times. Besides investigating parameters concerning the initiation system, a copolymerization study, using a large variety of comonomers, was conducted. This study led to the identification of an interesting fast polymerizing methacrylate: acetoacetoxyethyl methacrylate (AAEMA). The kinetics of this monomer were studied including the determination of the propagation rate coefficient kp and the copolymerization parameters with MMA rMMA and rAAEMA. The determined kinetic parameters were finally verified by a copolymerization simulation of MMA and AAEMA.

Polyethylene (PE) resins being non-polar in nature and having a high degree of crystallinity have limited miscibility and compatibility when blended with polar polymers. The miscibility and compatibility of these blends are generally worsened when they are prepared by direct injection moulding without a precompounding process. Such situations are commonly encountered in particular by polymer converters when blending colour and/or additive concentrates, commonly known as masterbatches. Typically, masterbatches are mixtures containing high loading of pigments and/or additives predispersed in a suitable solid vehicle (commonly known as carrier) such as a polyethylene resin. These masterbatches are usually used for the colouration of a wide range of polymers and the carrier used must therefore be compatible with these matrix (host) polymers. The preliminary stage of this study involved the investigation of the properties of blends based on high density polyethylene (HDPE) and a range of engineering thermoplastics (ABS, PC, PBT, PA6), prepared by injection moulding. Five different types of compatibilisers namely, ethylene-vinyl acetate (EVA) copolymer, ethylene-methyl acrylate (EMA) copolymer, ethylene-glycidyl methacrylate (E-GMA) copolymer, ethylene-methyl acrylateglycidyl methacrylate (E-MA-GMA) terpolymer and maleic anhydride grafted HDPE (HDPE-g-MAH) copolymer were evaluated with respect to their efficiencies in compatibilising HDPE with the four engineering polymers. The pre-compounded HDPE/compatibiliser binary blends at 2 different blend ratios (1:1 and 3:1) were added at 15 wt% concentration to each engineering thermoplastics and test samples were produced directly by injection moulding. Results of mechanical testing and characterisation of the blends showed that glycidyl methacrylate compatibilisers, E-MA-GMA, in particular have the most universal compatibilising effectiveness for a range of engineering thermoplastics including ABS, PC, PBT, and PA6. Blends compatibilised with E-MA-GMA compatibiliser had the best notched impact performance irrespective of matrix polymer type. The presence of an acrylic ester (methyl acrylate) comonomer in E-MA-GMA resulted in increased polarity of the ii compatibiliser leading to improved miscibility with the polar matrix polymers demonstrated by fine blend morphologies, melting point depression and reduction in crystallinity of the HDPE dispersed phase. The second stage of this study involved the reactive modification of HDPE using a low molecular weight di-functional solid diglycidyl ether of bisphenol A (DGEBA) type epoxy resin compatibilised with HDPE-g-MAH in an attempt to improve its compatibility with ABS, PBT and PA6. The maleic anhydride moieties in HDPE-g-MAH served as reactive sites for anchoring the epoxy moieties while the HDPE backbone was miscible with the HDPE resin. An excessive amount of reactive groups resulted in the formation of crosslinked gels while the addition of EVA co-compatibiliser helped in the reduction of gel content and further improved the dispersion of the epoxy. The effectiveness of epoxy grafted HDPE (with and without EVA co-compatibiliser) in compatibilising ABS/HDPE, PBT/HDPE, and PA6/HDPE was investigated by injection moulding of 5 wt% functionalised HDPE with these matrix polymers into test bars for mechanical testing, and characterisation by differential scanning calorimtery (DSC) and optical microscopy. The reactively functionalised HDPE blends, improved the mechanical properties of ABS and PA6 blends especially with EVA as co-compatibiliser. However, the mechanical properties of PBT blends were unmodified by the functionalised HDPE which was believed to be due to end-capping of the PBT chain-ends by ungrafted epoxy resins.

Des nanocapsules (NCs) biocompatibles destinées à l’administration intraveineuse d’agents anticancéreux hydrophobes ont été élaborées par polymérisation RAFT en miniémulsion, confinée à l’interface liquide/liquide. La polymérisation RAFT a été utilisée pour contrôler la croissance des greffons polymères constituant l’écorce des NCs à partir d’un transurf (macroagent RAFT et tensioactif) multifonctionnel dérivé du dextrane (DexN3-τCTAγ). Des NCs constituées d’une écorce en polymère hydrophobe (poly(méthacrylate de méthyle)) entourant un cœur liquide huileux (Miglyol®810) et recouvertes d’une couronne hydrophile polysaccharide (dextrane) ont ainsi été obtenues. Ces nano-objets ont été caractérisés en termes de taille, de recouvrement en dextrane (quantité de polysaccharide, épaisseur et stabilité), de stabilité colloïdale et de morphologie. La fabrication de NCs à écorce polymère pH-sensible a également été abordée. Enfin, le potentiel biomédical de ces nano-objets a été évalué grâce à différentes études : i) encapsulation et libération d’une substance active modèle, ii) cytotoxicité de NCs, iii) interactions des NCs avec les protéines plasmatiques et iv) fonctionnalisation de la surface des NCs par chimie « click ». / Biocompatible nanocapsules (NCs) for intravenous administration of hydrophobic anticancer agents were produced by interfacial Reversible Addition-Fragmentation chain Transfer (RAFT) miniemulsion polymerization. Controlled growth of polymeric grafts constituting NCs shell was obtained using a multi-reactive dextran-based transurf called DexN3-τCTAγ (acting both as macroRAFT agent and surfactant) to mediate RAFT polymerization at the liquid/liquid interface. NCs composed of a hydrophobic polymer shell (poly(methyl methacrylate)), an oily liquid core (Miglyol®810) and a hydrophilic polysaccharide coating (dextran) were obtained. These nano-objects were characterized in terms of size, dextran coverage (density, thickness and stability), colloidal stability and morphology. Synthesis of NCs with a pH-sensitive polymer shell was approached. Finally, potential of these nano-objects for biomedical applications was evaluated by studies on different aspects: i) encapsulation and delivery of a model active substance, ii) NCs cytotoxicity, iii) NCs interactions with plasma proteins, and iv) surface functionalization of NCs by “click chemistry”.

Des polymères à base de méthacrylate de poly(oxyde d'éthylène) (PEOMA) avec des chaînes pendantes PEO (Mn = 300 ou 950 g mol-1) ou des copolymères de PEOMA300 et d'acide méthacrylique (AMA) ont été synthétisés par polymérisation radicalaire contrôlée par les nitroxydes en utilisant une alkoxyamine (BlocBuilder®) comme amorceur en présence de SG1 et d'une faible quantité de styrène. Les copolymères à base de PEOMA300 et d'AMA sont thermo- et pH-sensibles. Les deux types de macroalkoxyamines ont été utilisés pour amorcer la copolymérisation en émulsion du méthacrylate de n-butyle et du styrène et former, par auto-assemblage induit par la polymérisation, des particules composées de copolymères à blocs amphiphiles, en absence ou présence de particules de silice. En absence de silice, des particules stabilisées de façon stérique ou électrostérique ont été formées. La polymérisation présente les caractéristiques d'une polymérisation contrôlée avec néanmoins la formation d'une faible proportion de chaînes mortes. L'effet du pH, de la force ionique et de la nature ou de la concentration des macroalkoxyamines sur la cinétique de polymérisation et la morphologie des particules a été étudié, et des sphères, des vésicules ou des nanofibres ont été obtenues. Les macroalkoxyamines à base de PEO s'adsorbent sur la silice via la formation de liaisons hydrogène entre les chaînes PEO et les groupes silanol. La synthèse de copolymères à blocs en surface de la silice a conduit à la formation de particules hybrides de différentes morphologies (bonhomme de neige, multipodes, framboise, coeur-écorce, têtard, mille pattes) liées à la taille de la silice, au pH et à la nature du macroamorceur / Water-soluble brush-type polymers composed of poly(ethylene)oxide methacrylate (PEOMA) units with PEO side groups of various chain lengths (Mn = 300 and 950 g mol-1) or of PEOMA300 with methacrylic acid (MAA) were synthesized by nitroxide-mediated polymerization using an alkoxyamine initiator (BlocBuilder®) and SG1 nitroxide in the presence of a low amount of styrene. The PEOMA300-MAA based copolymers showed a dual temperature/pH response. The two series of macroalkoxyamines were used in aqueous emulsion copolymerization of nbutyl methacrylate and styrene leading to the formation of particles composed of amphiphilic block copolymers through polymerization-induced self-assembly, in both the absence and presence of silica. The experiments performed in the absence of silica particles resulted in the formation of sterically or electrosterically stabilized latexes. The polymerization exhibited all the features of a controlled system with however the presence of a small proportion of dead chains. The effect of pH value, ionic strength and type and concentration of the macroalkoxyamine initiator on polymerization kinetics and latex morphologies was investigated. Depending on the reaction conditions, spherical particles, vesicles or nanofibers were successfully prepared. The PEO-based macroalkoxyamines were shown to adsorb on the silica surface via hydrogen bond interaction between PEO and the silanol groups. This enabled block copolymers to be generated in situ on the silica surface leading to hybrid particles with snowman, raspberry, daisy, core-shell, “tadpole-” and “centipede-” like morphologies depending on the silica particle size, pH value and type of macroinitiator

This master‘s thesis concerns gel polymer electrolytes formed on a methyl methacrylate base with selected types of nanoparticles. In the thesis are also analyzed the methods for measuring electrochemical properties. The practical portion deals with sample preparations of gel polymer electrolytes with different contents of alkaline salt in a solvent, creating gels with different nanoparticle content and comparing gel polymer electrolytes polymerized with heat and UV radiation. The thesis deals with the evaluation of these samples from the viewpoint of electrical conductivity and potential windows as well as thermal analysis of selected samples.

The theoretical part of this thesis is focused on bulk radical polymerization of styrene, methylmethacrylate, vinyltoluene and paramethylstyrene. It summarizes actual informations about kinetics and performance possibilities of bulk polymerization. Experimental part deals with polystyrene prepolymers preparation by bulk polymerization. The aim is to find optimal conditions for prepolymers preparation. Prepolymers should be usable for subsequent polymerization nearly up to 100% conversion. Conversion values were gravimetrically determined and molecular weights were obtained by viskosity measurements, which were realized by Ubbelohde viscometer. In the experimental part, there were performed simulations targeted on conversion dependence on time. The purpose was a prediction of monomer conversion at a given time during polymerization. Differences between reality and simulation were low in most of cases and the found form of kinetic behavior calculations provides satisfying results. In the conclusion of this thesis was suggested a new procedure for polystyrene prepolymers preparation.

Předkládaná práce se zabývá výzkumem nových materiálů a metod přípravy gelových polymerních elektrolytů (GPE) na bázi methakrylátů, které lze zejména vzhledem k jejich mechanickým vlastnostem s výhodou využít při konstrukci elektrochromních (EC) prvků.

No description available.

Several novel polymer monoliths for the analysis of peptides and proteins were synthesized using polyethylene glycol diacrylate (PEGDA) as crosslinker. Photo-initiated copolymerization of polyethylene glycol methyl ether acrylate and PEGDA yielded an inert monolith that could be used for size exclusion liquid chromatography of peptides and proteins. This macroscopically uniform monolith did not shrink or swell in either water or tetrahydrofuran. More importantly, it was found to resist adsorption of both acidic and basic proteins in aqueous buffer without any organic solvent additives. A strong cation-exchange polymer monolith was synthesized by copolymerization of 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) and PEGDA. A ternary porogen (water, methanol and ethyl ether) was found suitable to prepare a flow-through monolith with moderate pressure drop in aqueous buffer. The resulting monolith showed excellent ion exchange capillary liquid chromatography of peptides using a simple salt gradient. Extremely narrow peaks were obtained for the analysis of synthetic peptides, natural peptides and a protein digest. A peak capacity of 179 was achieved. Although the poly(AMPS) monolith demonstrated extraordinary performance, one main drawback of this monolith was its relatively strong hydrophobicity. A decrease in hydrophobicity was achieved by using more hydrophilic monomers (e.g., sulfoethyl methacrylate or vinyl sulfonic acid). The most hydrophilic poly(vinyl sulfonic acid) monolith provided high resolution cation-exchange liquid chromatography of protein standards and lipoproteins. Use of the new PEGDA biocompatible crosslinker over the conventional ethylene glycol dimethacrylate crosslinker for the preparation of polymer monoliths was found to be advantageous for the analysis of biological compounds in several chromatography modes.