Kyoto University (京都大学) / 0048 / 新制・課程博士 / 博士(工学) / 甲第17548号 / 工博第3707号 / 新制||工||1564(附属図書館) / 30314 / 京都大学大学院工学研究科建築学専攻 / (主査)教授 髙橋 大弐, 教授 鉾井 修一, 教授 竹脇 出 / 学位規則第4条第1項該当

Series impedances, including source and transfer impedances, are commonly used to model a variety of noise sources and noise treatment elements in duct systems. Particle velocity is assumed to be constant on the plane where the series impedances are defined. The research reported herein details investigations into measuring source and transfer impedance. Especially, the measurement and prediction of the transfer impedance of micro-perforated panel (MPP) absorbers is considered. A wave decomposition method for measuring source impedance and source strength was developed that was purely based on acoustic concepts instead of the equivalent circuit analysis. The method developed is a two-load method. However, it is not necessary to know the impedances of either load a priori. The selection of proper loads was investigated via an error analysis, and the results suggested that it was best to choose one resistive and one reactive load. In addition, a novel type of perforated element was investigated. MPP absorbers are metal or plastic panels with sub-millimeter size holes or slits. In the past, Maa's equation has been used to characterize their performance. However, Maa's equation is only valid for circular perforations. In this research, an inverse method using a nonlinear least square data fitting algorithm was developed to estimate effective parameters that could be used in Maa's theory. This inverse approach was also used to aid in understanding the effect of dust and fluid contamination on the performance of MPP absorbers. In addition, an approach to enhance the attenuation of MPP absorbers by partitioning the backing cavity was investigated experimentally and numerically. Results indicated that partitioning improved the attenuating of grazing sound waves. The effect of modifying both the source and transfer impedances on the system response was also studied using the Moebius transformation. It was demonstrated that the Moebius transformation is a mathematical tool that can be employed to aid in determining and understanding the impact of acoustic impedance modifications on a vibro-acoustic system.

Low frequency noise is a common problem in aircraft and launch vehicles. New technologies must be investigated to reduce this noise while contributing minimal weight to the structure. This thesis investigates passive and active control methods to improve low frequency sound absorption and transmission loss using acoustic metamaterials. The acoustic metamaterials investigated consist of poro-elastic acoustic heterogeneous (HG) metamaterials and microperforated (MPP) acoustic metamaterials. HG metamaterials consist of poro-elastic material with a periodic arrangement of embedded masses acting as an array of mass-spring- damper systems. MPP acoustic metamaterials consist of periodic layers of micro-porous panels embedded in poro-elastic material. This thesis examines analytically, experimentally, and numerically the behavior of acoustic metamaterials compared to a baseline poro-elastic sample. The development of numerical techniques using finite element analysis will aid in understanding the physics behind their functionality and will influence their design. Design studies are performed to understand the effects of varying the density, size, shape, and placement of the embedded masses as well as the location and distribution of microperforated panels in poro- elastic material. An active HG metamaterial is investigated, consisting of an array of active masses embedded within poro-elastic material. Successful tonal and broadband noise control is achieved using a feedforward, filtered-x LMS control algorithm to minimize the downstream sound pressure level. Low-frequency absorption and transmission loss is successfully increased in the critical frequency range below 500 Hz. Acoustic metamaterials are compact compared to conventional materials and find applications in controlling low-frequency sound radiation in aircraft and launch vehicles. / Master of Science

[EN] The aim of this work is to design new acoustic devices based on arrangements of scattering units. First, the use of sonic crystals as noise barriers for traffic noise control is comprehensively analyzed. Due to the limitations of the conventional structures based on rigid scatterers, the inclusion of absorbing elements is proposed. Two different types of absorbers are here considered: porous materials and microperforated plates. In the first case, the attenuation characteristics of barriers made with cylinders containing rubber crumb is analyzed. The second proposal is based on the construction of cylindrical microperforated shells. Analytical approaches modelling the behavior of the barriers have been developed in both cases. These models show a satisfactory agreement with the corresponding experimental realizations. Finally, it is performed an optimization process in order to obtain efficient sound barriers intended to attenuate traffic noise. Another application considered in this work is the construction of cloaks to render objects acoustically invisible. In particular, cloaks made with rigid inclusions are designed to operate with airborne sound. The first proposal consists of a cloak that utilizes the temperature of the background to control the properties of the effective medium. In addition, two and three-dimensional cloaks have been developed through the scattering cancellation technique. These devices have been designed by means of an optimization procedure and their performance has been experimentally demonstrated. / [ES] El objetivo de este trabajo es el diseño de nuevos dispositivos acústicos basados en disposiciones de centros de dispersión. En primer lugar, el uso de cristales sónicos como barreras acústicas para el control de ruido de tráfico es analizado en detalle. Debido a las limitaciones que presentan las estructuras convencionales basadas en centros de dispersión rígidos, se propone la inclusión de elementos absorbentes en los mismos. Se han considerado dos tipos distintos de absorbente: materiales porosos y placas microperforadas. En el primer caso se analizan las propiedades atenuadoras de barreras formadas por cilindros que contienen granza de caucho. La segunda solución se basa en la construcción de coronas microperforadas. En ambos casos se han desarrollado modelos analíticos que permiten determinar el comportamiento de las barreras. Dichos modelos muestran un acuerdo satisfactorio con las correspondientes realizaciones experimentales. Finalmente se ha realizado un proceso de optimización con objeto de obtener barreras eficientes para la atenuación de ruido de tráfico. Otra aplicación considerada en este trabajo es el desarrollo de dispositivos de invisibilidad acústica. Concretamente se pretenden diseñar mantos constituidos con elementos rígidos para ondas acústicas en aire. La primera propuesta consiste en un manto que utiliza la temperatura del medio externo para controlar sus propiedades efectivas. Además se han desarrollado mantos en dos y tres dimensiones a través de la técnica de cancelación de la dispersión. Los diseños han sido realizados por medio de un proceso de optimización y su funcionamiento ha sido demostrado experimentalmente. / [CA] L'objectiu d'aquest treball és el disseny de nous dispositius acústics basats en disposicions de centres de dispersió. En primer lloc, l'ús de vidres sònics com barreres acústiques per al control de soroll de trànsit és analitzat en detall. A causa de les limitacions que presenten les estructures convencionals basades en centres de dispersió rígids, es proposa la inclusió d'elements absorbents en els mateixos. S'han considerat dos tipus diferents de absorbent: materials porosos i plaques microperforades. En el primer cas s'analitzen les propietats atenuadores de barreres formades per cilindres que contenen gransa de cautxú. La segona solució es basa en la construcció de corones microperforades. En tots dos casos s'han desenvolupat models analítics que permeten determinar el comportament de les barreres. Aquests models mostren un acord satisfactori amb les corresponents realitzacions experimentals. Finalment s'ha realitzat un procés d'optimització per tal d'obtenir barreres eficients per l'atenuació de soroll de trànsit. Una altra aplicació considerada en aquest treball és el desenvolupament de dispositius d'invisibilitat acústica. Concretament es pretenen dissenyar mantells constituïts amb elements rígids per ones acústiques en aire. La primera proposta consisteix en un mantell que utilitza la temperatura del medi extern per controlar les seves propietats efectives. A més s'han desenvolupat mantells en dues i tres dimensions a través de la tècnica de cancel·lació de la dispersió. Els dissenys han estat realitzats per mitjà d'un procés d'optimització i el seu funcionament ha estat demostrat experimentalment. / García Chocano, VM. (2015). New devices for noise control and acoustic cloaking [Tesis doctoral]. Editorial Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/53026 / TESIS / Premios Extraordinarios de tesis doctorales

La mise en oeuvre de matériaux acoustiques est une méthode efficace et très utilisée pour réduire le bruit le long de sa propagation. Les propriétés acoustiques de nouvelles structures sandwich multifonctionnelles et de matériaux absorbants poreux sont étudiées dans la thèse. Les principales contributions de la thèse sont les suivantes: Les panneaux sandwich ont généralement d'excellentes propriétés mécaniques et un bon indice de perte en transmission sonore (STL), mais aucune capacité d'absorption acoustique. De nouvelles structures sandwich multifonctionnelles sont développées en intégrant des microperforations et des matériaux absorbants poreux aux panneaux sandwich ondulés et en nid d’abeilles conventionnels, structurellement efficaces pour obtenir de bons STL et de bonnes absorptions en basses fréquences. Le coefficient d'absorption acoustique (SAC) et la perte en transmission (STL) des panneaux sandwich ondulés sont évalués numériquement et expérimentalement en basse fréquence pour différentes configurations de perforations. Les modèles éléments finis (EF) sont construits en tenant compte des interactions vibro-acoustiques sur les structures et des dissipations d'énergie, visqueuse et thermique, à l'intérieur des perforations. La validité des calculs FE est vérifiée par des mesures expérimentales avec les échantillons testés obtenus par fabrication additive. Par rapport aux panneaux sandwich ondulés classiques sans perforation, les panneaux sandwich perforés (PCSPs) avec des perforations dans leur plaque avant présentent non seulement un SAC plus élevé aux basses fréquences, mais aussi un meilleur STL, qui en est la conséquence directe. L'élargissement des courbes des indices d’absorption et de transmission doit être attribué à la résonance acoustique induite par les micro-perforations. Il est également constaté que les PCSPs avec des perforations dans les plaques avant et les parois internes onduleés ont les fréquences de résonance les plus basses de tous les PCSPs. En outre, les performances acoustiques des panneaux sandwich en nid d'abeilles avec une plaque avant microperforée sont également examinées. Un modèle analytique est présenté avec l'hypothèse que les déplacements des deux plaques sont identiques aux fréquences inférieures à la fréquence de résonance des plaques. Le modèle analytique est ensuite validé par des modèles d'éléments finis et des résultats expérimentaux existants. Contrairement aux panneaux sandwich en nid d'abeilles classiques qui sont de piètres absorbeurs de bruit, les sandwichs en nid d'abeilles perforés (PHSPs) conduisent à un SAC élevé aux basses fréquences, ce qui entraîne en conséquence un incrément dans le STL basse fréquence. Les influences de la configuration du noyau sont étudiées en comparant les PHSPs avec différentes configurations de noyaux en nids d'abeilles. […] / Implementation of acoustic materials is an effective and popular noise reduction method during propagation. Acoustic properties of novel multifunctional sandwich structures and porous absorbing materials are studied in the dissertation. The main contributions of the dissertation are given as, Sandwich panels generally have excellent mechanical properties and good sound transmission loss (STL), but no sound absorption ability. Novel multifunctional sandwich structures are developed by integrating micro perforations and porous absorbing materials to the conventional structurally-efficient corrugated and honeycomb sandwich panels to achieve good SAC and STL at low frequencies. Low frequency sound absorption and sound transmission loss (STL) of corrugated sandwich panels with different perforation configurations are evaluated both numerically and experimentally. Finite element (FE) models are constructed with considerations of acousticstructure interactions and viscous and thermal energy dissipations inside the perforations. The validity of FE calculations is checked against experimental measurements with the tested samples provided by additive manufacturing. Compared with the classical corrugated sandwich panels without perforation, the perforated corrugated sandwich panels (PCSPs) with perforations in its face plate not only exhibits a higher SAC at low frequencies but also a better STL as a consequence of the enlarged SAC. The enlargement of SAC and STL should be attributed to the acoustical resonance induced by the micro perforations. It is also found that the PCSPs with perforations in both the face plates and corrugated cores have the lowest resonance frequencies of all the PCSPs. Besides, the acoustic properties of honeycomb sandwich panels with microperforated faceplate are also explored. An analytical model is presented with the assumption that displacements of the two faceplates are identical at frequencies below the faceplate resonance frequency. The analytical model is subsequently verified by finite element models and existing experimental results. Unlike classical honeycomb sandwich panels which are poor sound absorbers, perforated honeycomb sandwiches (PHSPs) lead to high SAC at low frequencies, which in turn brings about increment in the low frequency STL. Influences of core configuration are investigated by comparing PHSPs with different honeycomb core configurations. In order to enlarge the SAC bandwidth of perforated sandwich panels, porous absorbing materials are added to the cores of novel perforated sandwich panels. FE models are set up to estimate the SAC and STL of perforated sandwich panels with porous materials. Results show that perforated sandwich panels with porous material can provide SAC with broader bandwidth and lower resonance frequency than that without porous materials. Whereas the peak values in the SAC and STL curves are reduced due to the weakened acoustical resonance by the porous materials. […]

<p>Generally, heavier noise control treatments are favored over lighter ones since heavier acoustical materials tend to insulate (block) noise sources more effectively than do lighter materials. In automotive applications, however, heavier materials cannot always be adopted because of concerns over the total weight of the vehicle. Thus, it would be useful to identify lightweight acoustical treatments that can mitigate vehicle interior noise. Automotive sound packages have both absorption and barrier characteristics, and there is inevitably a trade-off between these two. Therefore, it is important to study the exchange between the absorption and transmission of acoustical materials particularly as it pertains to weight. Here, a procedure based on plane wave analysis is described that can be used to identify weight reduction opportunities by adjusting the acoustical properties of a generic sound package, consisting of a fibrous layer and a flexible microperforated panel surface treatment, so that it meets a target sound pressure level in a downstream interior space. It has been found, for the configuration studied here, that there are lightweight sound package configurations that can maintain acoustical performance equivalent to that of heavier noise treatments, and further, it has been found that the lightest treatments tend to favor barrier performance rather than absorption. Further, the impact of acoustical leaks has been considered, and it has been found that even very small leaks can result in a very substantial weight penalty if a specified level of acoustical performance is to be ensured. Further, the impact of changing the underlying panel mass and altering the frequency weighting used in the optimization process has also been considered.</p> <p>The optimizer used in the proposed procedure requires considerable calculation time; hence, the acoustic pressure calculation time needs to be minimized to enhance the efficiency of the solution process. Thus, the transfer matrix method (TMM) for a two-dimensional case was used to calculate the interior acoustic pressure for a simple geometry as a starting point in the process of identifying the minimum-weight sound packages. The TMM is a widely used analytical approach to predicting the sound pressure (and particle velocity) for a system that can be represented as a series of subsystems. Although the TMM can offer fast and simple calculations for the acoustic system, its application is limited to a plane-wave-based model. Thus, the TMM is not the best option for the acoustic pressure prediction in a complex geometry such as a vehicle interior, that involves non-planar wave propagation. Therefore, a hybrid TMM-FEA method is proposed in this research to evaluate the acoustical performance of the sound package in more complex geometries (here, a vehicle-like cavity). So, in this research, the TMM was introduced to obtain the initial solutions that can be used in conjunction with the FEA tool to calculate the sound pressure field in the complex geometry case. The correlation between the results of these two approaches was then analyzed to develop a space-averaged pressure prediction model for various absorptive cases in the interior space. Finally, this SAP prediction model was used to generate an acoustic map that can be used to graphically estimate the SAPs in the complex geometry case.</p> <p>In order to validate the usage of the developed equation for different sets of boundary conditions, several case studies were performed to study the effects of the surface impedance arrangements, geometrical shapes, and, lastly, the presence of extra features in the interior space. Finally, the SAP difference between the area near the driver’s right ear and the total interior cavity was studied to show that the SAP of the total cavity can be adjusted to evaluate the acoustic performance of the sound packages along the lines of conventional industry practice. </p>