The deleterious effect of moisture on the structural integrity of asphalt mixtures has been recognized as one of the main causes of early deterioration of asphalt pavements. This phenomenon, usually referred to as moisture damage, is defined as the progressive loss of structural integrity of the mixture that is primarily caused by the presence of moisture in liquid or vapor state. Moisture damage is associated with the development of different physical, mechanical, and chemical processes occurring within the microstructure of the mixture at different intensities and rates. Although there have been important advancements in identifying and characterizing this phenomenon, there is still a lack of understanding of the damage mechanisms occurring at the microscopic level. This situation has motivated the research work reported in this dissertation. The main objective of this dissertation is to formulate and apply a numerical micromechanical model of moisture-induced damage in asphalt mixtures. The model focuses on coupling the effects of moisture diffusion—one of the three main modes of moisture transport within asphalt mixtures—with the mechanical performance of the microstructure. Specifically, the model aims to account for the effect of moisture diffusion on the degradation of the viscoelastic bulk matrix of the mixture (i.e., cohesive degradation) and on the gradual deterioration of the adhesive bonds between the aggregates and the asphalt matrix (i.e., adhesive degradation). The micromechanical model was applied to study the role of some physical and mechanical properties of the constitutive phases of the mixtures on the susceptibility of the mixture to moisture damage. The results from this analysis suggest that the diffusion coefficients of the asphalt matrix and aggregates, as well as the bond strength of the aggregate-matrix interface, have the most influence on the moisture susceptibility of the mixtures. The micromechanical model was further used to investigate the influence of the void phase of asphalt mixtures on the generation of moisture-related deterioration processes. Two different probabilistic-based approaches were used to accomplish this objective. In the first approach, a volumetric distribution of air voids sizes measured using X-Ray Computed Tomography in a dense-graded asphalt mixture was used to generate probable void structures in a microstructure of an asphalt mixture. In the second approach, a stochastic modeling technique based on random field theory was used to generate probable air voids distributions of the mixture. In this second approach, the influence of the air voids was accounted for by making the physical and mechanical properties of the asphalt matrix dependent on probable voids distributions. Although both approaches take into consideration the characteristics of the air void phase on the mechanical response of the mixtures subjected to moist environments, the former explicitly introduces the air phase within the microstructure while the latter indirectly includes its effects by modifying the material properties of the bulk matrix. The results from these simulations demonstrated that the amount, variability and location of air voids are decisive in determining the moisture-dependent performance of asphalt mixtures. The results from this dissertation provide new information on the kinetics of moisture damage mechanisms in asphalt mixtures. In particular, the results obtained from applying the micromechanical model permitted identification of the relative influence of the characteristics of the constitutive phases of a mixture on its moisture-related mechanical performance. This information can be used as part of design methodologies of asphalt mixtures, and/or as an input in life-cycle analysis models and maintenance programs of road infrastructure.

Moisture damage in asphalt mixes can be defined as loss of strength and durability due to the presence of moisture at the binder-aggregate interface (adhesive failure) or within the binder (cohesive failure). This research focuses on the evaluation of the susceptibility of aggregates and asphalts to moisture damage through understanding the micro-mechanisms that influence the adhesive bond between aggregates and asphalt and the cohesive strength and durability of the binder. Moisture damage susceptibility is assessed using surface energy measurements and dynamic mechanical analysis (DMA). Surface energy is defined as the energy needed to create a new unit surface area of material in vacuum condition. Surface energy measurements are used to compute the adhesive bond strength between the aggregates and asphalt and cohesive bond strength in the binder. DMA testing is used to evaluate the rate of damage accumulation in asphalt binders and mastics. The DMA applies a cyclic, torsional strain controlled loading to cylindrical asphalt mastics until failure. The DMA results are analyzed using continuum damage mechanics that focuses on separating the energy expended in damaging the material from that associated with viscoelastic deformation. A new approach is developed to analyze the DMA results and calculate the rate of damage. The developed approach is used to evaluate six asphalt mixtures which have performed either well or poorly in the field. The resistance of the field mixes to moisture damage is shown to be related to the calculations of bind energies and the accumulated damage in the DMA.

The presence of moisture in hot mix asphalt (HMA) causes loss of strength and durability of the mix, which is referred to as moisture damage. This study deals with the development of experimental methods for measuring total suction in HMA, which can be defined as the free energy state of water in HMA mixes. The total suction is related to the ability of moisture to get into the mix under unsaturated conditions; it is also related to the ability of the mix to retain moisture. Soil suction has been studied extensively. However, suction in HMA as a porous material and its relationship to moisture damage have not been studied. The development of a procedure to measure the total suction in HMA mixes is the first objective of this research. The second objective is to relate suction measurements to physical and chemical properties of the mixtures. The objectives were achieved in two phases. In the first phase, the total suction was measured in HMA specimens with different types of aggregates (limestone and granite), and with different air void distributions and aggregate gradations. The results of this phase showed that the drying test using a 60 oC temperature-controlled room is the proper setup for measuring the total suction in HMA using thermocouple psychrometers. The characteristics of suction-moisture content curves were found to be related to the air void distribution in HMA. In the second phase, total suction was measured in sand asphalt specimens. These specimens had different combinations of aggregates and binders with different bond energies and exhibited different field performance in terms of resistance to moisture damage. The suction measurements in sand asphalt specimens were used to calculate the moisture diffusion coefficient. The results revealed that water diffused into sand asphalt specimens that are known to have poor resistance to moisture damage faster than those that are known to have good resistance to moisture damage

The presence of moisture in hot mix asphalt (HMA) causes loss of strength and durability of the mix, which is referred to as moisture damage. This study deals with the development of experimental methods for measuring total suction in HMA, which can be defined as the free energy state of water in HMA mixes. The total suction is related to the ability of moisture to get into the mix under unsaturated conditions; it is also related to the ability of the mix to retain moisture. Soil suction has been studied extensively. However, suction in HMA as a porous material and its relationship to moisture damage have not been studied. The development of a procedure to measure the total suction in HMA mixes is the first objective of this research. The second objective is to relate suction measurements to physical and chemical properties of the mixtures. The objectives were achieved in two phases. In the first phase, the total suction was measured in HMA specimens with different types of aggregates (limestone and granite), and with different air void distributions and aggregate gradations. The results of this phase showed that the drying test using a 60 oC temperature-controlled room is the proper setup for measuring the total suction in HMA using thermocouple psychrometers. The characteristics of suction-moisture content curves were found to be related to the air void distribution in HMA. In the second phase, total suction was measured in sand asphalt specimens. These specimens had different combinations of aggregates and binders with different bond energies and exhibited different field performance in terms of resistance to moisture damage. The suction measurements in sand asphalt specimens were used to calculate the moisture diffusion coefficient. The results revealed that water diffused into sand asphalt specimens that are known to have poor resistance to moisture damage faster than those that are known to have good resistance to moisture damage

Pavements are a major part of the infrastructure in the United States. Moisture damage of these pavements is a significant problem. To predict and prevent this kind of moisture damage a great deal of research has been performed on this issue in past. This study validates an analytical approach based on surface energy aimed at assessing moisture damage. Two types of bitumen and three aggregates are evaluated in the study. The two types of bitumen represent very different chemical extremes and the three aggregates (a limestone, siliceous gravel, and granite) represent a considerable range in mineralogy. Moisture damage was monitered as a change in dynamic modulus with load cycles. The analysis demonstrates the need to consider mixture compliance as well as bond energy in order to predict moisture damage. Mixtures with the two types of bitumen and each aggregate with and without hydrated lime were evaluated. The hydrated lime substantially improved the resistance of the mixture to moisture damage.

This doctoral thesis presents results of literature review on classical and contemporary aspects of stripping, as well as experimental investigations on moisture damage as influenced by bituminous materials. Previous research in the area of moisture damage was reviewed and synthesized into a state-of-the-art. Important parameters linked to moisture sensitivity, like bituminous material characteristics, dynamic loads from heavy vehicles, environmental factors, construction practice and nature of anti-stripping additives, are presented. The state-of-the-art in current test methods is summarized and given. The experimental work involved investigations of the influence of bitumen and aggregate composition on water susceptibility. The influence of aggregate mineralogy and chemistry was evaluated using eleven aggregates and one bitumen, followed by studying the interactive effect of four bitumens and four aggregates. Moisture sensitivity was evaluated in accordance with (EN 12697-12:2003) for conditioning, ASTM D 4123 for resilient modulus determination, and (EN 12697-23:2003) for indirect tensile strength testing. Furthermore, thermal stability of two liquid amine anti-stripping additives mixed with two bitumens of varied acidity was investigated using potentiometric titration and Fourier Transform Infrared (FTIR) Spectroscopy. Lastly, a technique based on Fourier Transform Infrared Spectroscopy-Attenuated Total Reflectance (FTIR-ATR) was developed and used for studying transport of water across thin bitumen films, as well as stripping at bitumen/substrate interfaces. Bitumens from different sources and three substrates (silicon, germanium and zinc selenide crystals) were used. Based on the results obtained, it was concluded that aggregates containing sodium and potassium in alkali feldspars generally showed high moisture sensitivity. In contrast, presence of calcium, magnesium and iron was associated with aggregates with low moisture sensitivity. Contrary to several previous findings, one aggregate with practically 100% quartz exhibited low moisture sensitivity. No linear relationship between moisture sensitivity and the contents of SiO2 and Al2O3 in the aggregates studied was established. Results of the interactive influence of bitumen and aggregate composition showed that high acid and low penetration bitumens exhibited high dry strength for all the aggregates studied. On the other hand, for a given bitumen, the wet strengths were found to be aggregate specific. The results of tests on thermal stability of amine additives showed that usefulness of these additives reduces considerably, when the more alkaline additive was mixed with the high acid bitumen, followed by storing the blends under pronounced conditions of time and temperature (24 hours and 140ºC, or more, in this study). Much less interaction occurred when the less alkaline additive was blended with the low acid bitumen. Even if a correlation was found between the results of potentiometric titration and Fourier Transform Infrared spectroscopy, the latter was not considered good enough at detecting amine additives, especially at low dosages. The technique based on FTIR-ATR developed in this study distinguished between good and bad bitumens with regard to stripping. The effectiveness of amine-based additives in reducing stripping was also shown by the method. Three likely processes occurred during the test, namely water diffusion, film break, and displacement (stripping) of bitumen from the substrate surface. The results also indicated that the diffusion process of water into the bitumen/substrate interface does not obey Fick’s law. / QC 20100831

Fatigue cracking and moisture damage are two important modes of distresses in asphalt pavements. Recently, the Dynamic Mechanical Analyzer (DMA) was used to characterize fatigue cracking and evaluate the effects of moisture damage on the Fine Aggregate Matrix (FAM) portion of asphalt mixtures. The FAM specimens should be properly fabricated to represent the composition and structure of the fine portion of the mixture. The objective of the first phase of this study was to develop a standard test procedure for preparing FAM specimens such that it is representative of the mixture. The method consists of preparing loose full asphalt mixtures and sieving through different sizes. Then, the ignition oven was used to determine the binder content associated with the small size materials (passing on sieve #16). Sieve #16 is used to separate fine aggregates from the coarse aggregates. The applicability of this new method will be evaluated using a number of asphalt mixtures. The objective of the second phase of this study was to develop software to analyze the data from DMA test. Such software will enable engineers and researchers to perform the complex analysis in very short time. This is Microsoft Windows ® based software, executable in any hardware configuration under this operational system.

abstract: A recent joint study by Arizona State University and the Arizona Department of Transportation (ADOT) was conducted to evaluate certain Warm Mix Asphalt (WMA) properties in the laboratory. WMA material was taken from an actual ADOT project that involved two WMA sections. The first section used a foamed-based WMA admixture, and the second section used a chemical-based WMA admixture. The rest of the project included control hot mix asphalt (HMA) mixture. The evaluation included testing of field-core specimens and laboratory compacted specimens. The laboratory specimens were compacted at two different temperatures; 270 °F (132 °C) and 310 °F (154 °C). The experimental plan included four laboratory tests: the dynamic modulus (E*), indirect tensile strength (IDT), moisture damage evaluation using AASHTO T-283 test, and the Hamburg Wheel-track Test. The dynamic modulus E* results of the field cores at 70 °F showed similar E* values for control HMA and foaming-based WMA mixtures; the E* values of the chemical-based WMA mixture were relatively higher. IDT test results of the field cores had comparable finding as the E* results. For the laboratory compacted specimens, both E* and IDT results indicated that decreasing the compaction temperatures from 310 °F to 270 °F did not have any negative effect on the material strength for both WMA mixtures; while the control HMA strength was affected to some extent. It was noticed that E* and IDT results of the chemical-based WMA field cores were high; however, the laboratory compacted specimens results didn't show the same tendency. The moisture sensitivity findings from TSR test disagreed with those of Hamburg test; while TSR results indicated relatively low values of about 60% for all three mixtures, Hamburg test results were quite excellent. In general, the results of this study indicated that both WMA mixes can be best evaluated through field compacted mixes/cores; the results of the laboratory compacted specimens were helpful to a certain extent. The dynamic moduli for the field-core specimens were higher than for those compacted in the laboratory. The moisture damage findings indicated that more investigations are needed to evaluate moisture damage susceptibility in field. / Dissertation/Thesis / M.S. Civil and Environmental Engineering 2011

abstract: Bio-modification of asphalt binder brings significant benefits in terms of increasing sustainable and environmental practices, stabilizing prices, and decreasing costs. However, bio-modified asphalt binders have shown varying performance regarding susceptibility to moisture damage; some bio-oil modifiers significantly increase asphalt binder's susceptibility to moisture damage. This variability in performance is largely due to the large number of bio-masses available for use as sources of bio-oil, as well as the type of processing procedure followed in converting the bio-mass into a bio-oil for modifying asphalt binder. Therefore, there is a need for a method of properly evaluating the potential impact of a bio-oil modifier for asphalt binder on the overall performance of asphalt pavement, in order to properly distinguish whether a particular bio-oil modifier increases or decreases the moisture susceptibility of asphalt binder. Therefore, the goal of this study is a multi-scale investigation of bio-oils with known chemical compositions to determine if there is a correlation between a fundamental property of a bio-oil and the resulting increase or decrease in moisture susceptibility of a binder when it is modified with the bio-oil. For instance, it was found that polarizability of asphalt constituents can be a promising indicator of moisture susceptibility of bitumen. This study will also evaluate the linkage of the fundamental property to newly developed binder-level test methods. It was found that moisture-induced shear thinning of bitumen containing glass beads can differentiate moisture susceptible bitumen samples. Based on the knowledge determined, alternative methods of reducing the moisture susceptibility of asphalt pavement will also be evaluated. It was shown that accumulation of acidic compounds at the interface of bitumen and aggregate could promote moisture damage. It was further found that detracting acidic compounds from the interface could be done by either of neutralizing active site of stone aggregate to reduce affinity for acids or by arresting acidic compounds using active mineral filler. The study results showed there is a strong relation between composition of bitumen and its susceptibility to moisture. This in turn emphasize the importance of integrating knowledge of surface chemistry and bitumen composition into the pavement design and evaluation. / Dissertation/Thesis / Doctoral Dissertation Civil, Environmental and Sustainable Engineering 2020

För att efterleva Regeringens miljöpolitik har Boverket tilldelats ansvaret för miljömålet God bebyggd miljö. Boverket är en myndighet som arbetar för Riksdagens miljömål och skall vid behov förslå åtgärder för miljöarbetets utveckling. I Boverkets Byggregler finns krav som måste följas för att uppnå ett fuktsäkert byggande. Som förslag på hur dessa krav ska uppnås nämns Svensk Byggindustriers metod ByggaF – Metod för fuktsäkert byggande. ByggaF är en dokumentsamling med mallar, checklistor, kontrollpunkter och rutiner. Dessa dokument kan då ligga till grund för att upprätta en metod som säkerställer fuktsäkerheten under alla byggskeden. Skadefall har studerats i syfte att påvisa hur ByggaF fungerar och nyttan i att använda det. I samtliga av de behandlade fallen har kopplingar kunnat finnas till ByggaF, som kan förhindra problematiken. På så vis har dess täckningsgrad bekräftats. Kontakt har upprättats med flertalet aktörer i branschen för att få en uppfattning om hur metoden har tagits emot i branschen efter att den lanserades år 2007. Utifrån intervjuerna uppfattas att de flesta entreprenörer hört talas om metoden men inte använt den själva. Däremot har fuktsakkunniga använt den som underlag för att ta fram egna interna fuktsäkerhetsplaner. På grund av det används den av entreprenörer indirekt. Hos beställare ställs ByggaF som ett krav om man väljer att miljöcertifiera i Silver- eller Guldklass hos Miljöbyggnad. Annars ställs det oftast inte tillräckligt med krav på fuktsäkerhetsmetoder. / Included in Boverkets Byggregler are a number of demands that must be fulfilled in order to achieve a moisture safe construction. One of the suggestions on how to fulfil these demands is to use the method developed by Svensk Byggindustri, ByggaF – Method for moisture safe construction. In order to work according to the government’s environmental politics, Boverket has been given the responsibility to fulfil the aims of God bebyggd miljö, it is also their work to ensure that operations and establishments fulfil and reaches the goals that have been set by the Swedish government. ByggaF is a collection of documents including templates, check lists, control points and routines; these documents can be used during the whole building process to create a method which ensures that the moisture safety is withheld. It has been investigated whether or not cases of moisture damages could have been prevented with the proper use of ByggaF. In all the cases that have been studied, ByggaF could have been used to prevent mistakes and problems and by this, the efficiency and importance of the documents has been proven. Several major actors within the field have been contacted in order to gain a larger understanding about how the method has been perceived and utilized since its launch in 2007. In general most of the entrepreneurs has heard of the method but never used it themselves. However, moisture specialist from major construction operations, have utilized ByggaF in order to develop internal moisture safety routines, therefor ByggaF is indirectly used by the entrepreneurs. ByggaF would, for constructors, be a requirement if one desires an environmental certification in either the gold or the silver category within the framework of Miljöbyggnad. Normally there are not enough requirements set regarding methods for moisture safety.