No description available.

There are two main goals of this thesis: to investigate the flow-induced crystallization behaviour of Polybutene-1 (PB-1 samples, and to study the effects of molecular parameters on the crystallization behaviour While flow-induced crystallization is not a new area in polymer research, well-defined experimental methods that allow access to high flow rate range comparable to that encountered in real processing are still lacking. Two types of flow are considered: shear and uniaxial elongational. Regarding the second aim, several molecular parameters considered are: molecular weight, molecular weight distribution, isotacticity, presence of nucleating agents, and copolymer content. For this purpose an array of PB-1 samples were used. It is found that each of these parameters can have significant effect on the crystallization behaviour. Mainly rheological methods were utilized to conduct the flow-induced crystallization experiments. Crystallization onset time is define d from the change in viscosity or other related parameters. The experiments begin with low shear rate range, to ensure that the results are comparable with literature data. In this range we encounter the quasi-quiescent onset time at very small. shear rates, which draws an interesting comparison with another physical parameter, the gel time. Beyond a critical flow rate a decrease in the onset time is seen, and a plateau-and-slope trend is evident for a curve of onset time vs. shear rate. Using a combination of three experimental methods, shear rates ranging from Q0001 - 500 s-1 are successfully achieved, and a good agreement between these methods is observed. Furthermore, a normalization procedure is introduced, which yields temperature-invariant curves for the mentioned range of shear rate. For the uniaxial elongation flow, the Elongational Viscosity Fixture (EVF) is employed, with the strain rate ranging from 0.0001 - 10 s'. A greater reduction in onset time as compared to shear (at the same shear/strain r ate) is observed, and the difference in the onset times for shear and elongation already reaches more than one decade for a flow rate of 10 5. This quantitative comparison is particularly important; since not so many data on elongation-induced crystallization are available in the literature. Finally, the thesis compares several flow induced crystallization models that can be useful as prediction tools and selects one of these models to be compared with the experimental data. A qualitative agreement is found, however, for better quantitative prediction the model still needs to be.

The objective of this work is to develop mathematical models to predict molecular weight distributions (MWDs) of ethylene copolymers produced in an industrial gas-phase reactor using a Ziegler-Natta (Z-N) catalyst. Because of the multi-site nature of Z-N catalysts, models of Z-N catalyzed copolymerization tend to be very large and have many parameters that need to be estimated. It is important that the data that are available for parameter estimation be used effectively, and that a suitable balance is achieved between modeling rigour and simplification. In the thesis, deconvolution analysis is used to gain an understanding of how the polymer produced by various types of active sites on the Z-N catalyst responds to changes in the reactor operating conditions. This analysis reveals which reactions are important in determining the MWD and also shows that some types of active sites share similar behavior and can therefore share some kinetic parameters. With this knowledge, a simplified model is developed to predict MWDs of ethylene/hexene copolymers produced at 90 °C. Estimates of the parameters in this isothermal model provide good initial guesses for parameter estimation in a subsequent more complex model. The isothermal model is extended to account for the effects of butene and temperature. Estimability analysis and cross-validation are used to determine which parameters should be estimated from the available industrial data set. Twenty model parameters are estimated so that the model provides good predictions of MWD and comonomer incorporation. Finally, D-, A-,and V-optimal experimental designs for improving the quality of the model predictions are determined. Difficulties with local minima are addressed and a comparison of the optimality criteria is presented. / Thesis (Ph.D, Chemical Engineering) -- Queen's University, 2009-05-28 20:43:58.37

No description available.

A distribuição de massa molar (DMM) e seus parâmetros são de fundamental importância na caracterização dos polímeros. Por este motivo, o desenvolvimento de técnicas que permitam a determinação da DMM de forma mais rápida e a menor custo é de grande importância prática. Os principais objetivos deste trabalho foram a implementação de alguns dos modelos baseados da teoria da reptação dupla propostos na literatura para descrever o mecanismo de relaxação das cadeias poliméricas, a avaliação dessas implementações e a análise de dois passos fundamentais na obtenção da DMM a partir de dados reológicos que são a metodologia de cálculo do espectro de relaxação baseado no modelo de Maxwell e a estratégia para a avaliação numérica das integrais que aparecem nos modelos de relaxação. Foi resolvido o problema denominado problema inverso, ou seja, a determinação da DMM a partir de dados reológicos usando um modelo de relaxação especificado e uma função de distribuição imposta. Foi usada a função Exponencial Generalizada (GEX) para representar a probabilidade de distribuição, sendo consideradas duas abordagens: i) cálculo explícito do espectro de relaxação e ii) aproximações paramétricas de Schwarzl, que evitam a necessidade do cálculo explícito do espectro de relaxação. A metodologia de determinação da DMM foi aplicada para amostras de polietileno e foram estimadas distribuições com boa representação dos dados experimentais do GPC, ao considerarem-se amostras com polidispersões inferiores a 10. Com relação a metodologia de cálculo do espectro de relaxação, foi realizado um estudo comparativo da aplicação de espectros de relaxação discreto e contínuo, com o objetivo de estabelecer critérios para especificação do número ótimo de modos de Maxwell a serem considerados. Ao efetuar-se a comparação entre as técnicas, verificou-se o espectro discreto apresenta como um sistema melhor condicionado, permitindo assim obter maior confiabilidade dos parâmetros estimados. Também é proposta uma modificação da metodologia de determinação da DMM, em que é aplicada a quadratura de Gauss-Hermite para a resolução numérica da integral dos modelos de relaxação. / The molecular weight distribution (MWD) and its parameters are of the fundamental importance in the characterization of polymers. Therefore, the development of techniques for faster and less time consuming determination of the MWD is of great practical relevance. The goals of this work were the implementation of some of the relaxation models from double reptation theory proposed in the literature, the evaluation of these implementations and the analysis of two key points in the recovery of the MWD from rheological data which are the methodology for calculation of the relaxation spectrum based on the Maxwell model and the numeric strategy for the evaluation of the integrals appearing in the relaxation models. The inverse problem, i.e., the determination of the MWD from rheological data using a specified relaxation model and an imposed distribution function, was solved. In the analysis of the inverse problem, the Generalized Exponential (GEX) was used as distribution function and two approaches were considered: i) explicit calculation of the relaxation spectrum and ii) use of the parametric method proposed by Schwarzl to avoid the explicit calculation of the relaxation spectrum. In the test of commercial samples of polyethylene with polidispersity less than 10, the application of this methodology led to MWD curves which provided good fit of the experimental SEC data. Regarding the methodology for calculation of the relaxation spectrum, a comparison between the performance of discrete and continuous relaxation spectrum was performed and some possible a criteria to determine the appropriate number of relaxation modes of Maxwell to be used were evaluated. It was found that the technique of discrete spectrum leads to better conditioned systems and, consequently, greater reliability of the estimated parameters. With relation to the numeric strategy for the evaluation of the integrals appearing in the relaxation models, the use of Gauss-Hermite quadrature using a new change of variables was proposed.

A distribuição de massa molar (DMM) e seus parâmetros são de fundamental importância na caracterização dos polímeros. Por este motivo, o desenvolvimento de técnicas que permitam a determinação da DMM de forma mais rápida e a menor custo é de grande importância prática. Os principais objetivos deste trabalho foram a implementação de alguns dos modelos baseados da teoria da reptação dupla propostos na literatura para descrever o mecanismo de relaxação das cadeias poliméricas, a avaliação dessas implementações e a análise de dois passos fundamentais na obtenção da DMM a partir de dados reológicos que são a metodologia de cálculo do espectro de relaxação baseado no modelo de Maxwell e a estratégia para a avaliação numérica das integrais que aparecem nos modelos de relaxação. Foi resolvido o problema denominado problema inverso, ou seja, a determinação da DMM a partir de dados reológicos usando um modelo de relaxação especificado e uma função de distribuição imposta. Foi usada a função Exponencial Generalizada (GEX) para representar a probabilidade de distribuição, sendo consideradas duas abordagens: i) cálculo explícito do espectro de relaxação e ii) aproximações paramétricas de Schwarzl, que evitam a necessidade do cálculo explícito do espectro de relaxação. A metodologia de determinação da DMM foi aplicada para amostras de polietileno e foram estimadas distribuições com boa representação dos dados experimentais do GPC, ao considerarem-se amostras com polidispersões inferiores a 10. Com relação a metodologia de cálculo do espectro de relaxação, foi realizado um estudo comparativo da aplicação de espectros de relaxação discreto e contínuo, com o objetivo de estabelecer critérios para especificação do número ótimo de modos de Maxwell a serem considerados. Ao efetuar-se a comparação entre as técnicas, verificou-se o espectro discreto apresenta como um sistema melhor condicionado, permitindo assim obter maior confiabilidade dos parâmetros estimados. Também é proposta uma modificação da metodologia de determinação da DMM, em que é aplicada a quadratura de Gauss-Hermite para a resolução numérica da integral dos modelos de relaxação. / The molecular weight distribution (MWD) and its parameters are of the fundamental importance in the characterization of polymers. Therefore, the development of techniques for faster and less time consuming determination of the MWD is of great practical relevance. The goals of this work were the implementation of some of the relaxation models from double reptation theory proposed in the literature, the evaluation of these implementations and the analysis of two key points in the recovery of the MWD from rheological data which are the methodology for calculation of the relaxation spectrum based on the Maxwell model and the numeric strategy for the evaluation of the integrals appearing in the relaxation models. The inverse problem, i.e., the determination of the MWD from rheological data using a specified relaxation model and an imposed distribution function, was solved. In the analysis of the inverse problem, the Generalized Exponential (GEX) was used as distribution function and two approaches were considered: i) explicit calculation of the relaxation spectrum and ii) use of the parametric method proposed by Schwarzl to avoid the explicit calculation of the relaxation spectrum. In the test of commercial samples of polyethylene with polidispersity less than 10, the application of this methodology led to MWD curves which provided good fit of the experimental SEC data. Regarding the methodology for calculation of the relaxation spectrum, a comparison between the performance of discrete and continuous relaxation spectrum was performed and some possible a criteria to determine the appropriate number of relaxation modes of Maxwell to be used were evaluated. It was found that the technique of discrete spectrum leads to better conditioned systems and, consequently, greater reliability of the estimated parameters. With relation to the numeric strategy for the evaluation of the integrals appearing in the relaxation models, the use of Gauss-Hermite quadrature using a new change of variables was proposed.

abstract: Asphalt binder is a complex viscoelastic hydrocarbon, whose performance depends upon interaction between its physical and chemical properties, both of which are equally important to the successful understanding of the material. Researchers have proposed various models linking linear viscoelastic (LVE) and microstructural parameters. However, none of these parameters provide insight into the relationship in the non- linear viscoelastic NLVE domain. The main goals of this dissertation are two fold. The first goal is to utilize the technique of Laser Desorption Mass Spectroscopy (LDMS) to relate the molecular structure of asphalt binders to its viscoelastic properties. The second goal of the study is to utilize different NLVE characterization tools and analysis procedures to get a clear understanding of the NLVE behavior of the asphalt binders. The goals of the study are divided into four objectives; 1) Performing the LDMS test on asphalt binder to develop at the molecular weight distributions for different asphalts, 2) Characterizing LVE properties of Arizona asphalt binders, 3) Development of relationship between molecular structure and linear viscoelasticity, 4) Understanding NLVE behavior of asphalt binders through three different characterization methods and analysis techniques. In this research effort, a promising physico-chemical relationship is developed between number average molecular weight and width of relaxation spectrum by utilizing the data from LVE characterization and the molecular weight distribution from LDMS. The relationship states that as the molecular weight of asphalt binders increase, they require more time to relax the developed stresses. Also, NLVE characterization was carried out at intermediate and high temperatures using three different tests, time sweep fatigue test, repeated stress/strain sweep test and Multiple Stress Creep and Recovery (MSCR) test. For the intermediate temperature fatigue tests, damage characterization was conducted by applying the S-VECD model and it was found that aged binders possess greater fatigue resistance than unaged binders. Using the high temperature LAOS tests, distortion was observed in the stress-strain relationships and the data was analyzed using a Fourier transform based tool called MITlaos, which deconvolves stress strain data into harmonic constituents and aids in identification of non-linearity by detecting higher order harmonics. Using the peak intensities observed at higher harmonic orders, non-linearity was quantified through a parameter termed as “Q”, which in future applications can be used to relate to asphalt chemical parameters. Finally, the last NLVE characterization carried out was the MSCR test, where the focus was on the scrutiny of the Jnrdiff parameter. It was found that Jnrdiff is not a capable parameter to represent the stress-sensitivity of asphalt binders. The developed alternative parameter Jnrslope does a better job of not only being a representative parameter of stress sensitivity but also for temperature sensitivity. / Dissertation/Thesis / Doctoral Dissertation Civil, Environmental and Sustainable Engineering 2018

A distribuição de massa molar (DMM) e seus parâmetros são de fundamental importância na caracterização dos polímeros. Por este motivo, o desenvolvimento de técnicas que permitam a determinação da DMM de forma mais rápida e a menor custo é de grande importância prática. Os principais objetivos deste trabalho foram a implementação de alguns dos modelos baseados da teoria da reptação dupla propostos na literatura para descrever o mecanismo de relaxação das cadeias poliméricas, a avaliação dessas implementações e a análise de dois passos fundamentais na obtenção da DMM a partir de dados reológicos que são a metodologia de cálculo do espectro de relaxação baseado no modelo de Maxwell e a estratégia para a avaliação numérica das integrais que aparecem nos modelos de relaxação. Foi resolvido o problema denominado problema inverso, ou seja, a determinação da DMM a partir de dados reológicos usando um modelo de relaxação especificado e uma função de distribuição imposta. Foi usada a função Exponencial Generalizada (GEX) para representar a probabilidade de distribuição, sendo consideradas duas abordagens: i) cálculo explícito do espectro de relaxação e ii) aproximações paramétricas de Schwarzl, que evitam a necessidade do cálculo explícito do espectro de relaxação. A metodologia de determinação da DMM foi aplicada para amostras de polietileno e foram estimadas distribuições com boa representação dos dados experimentais do GPC, ao considerarem-se amostras com polidispersões inferiores a 10. Com relação a metodologia de cálculo do espectro de relaxação, foi realizado um estudo comparativo da aplicação de espectros de relaxação discreto e contínuo, com o objetivo de estabelecer critérios para especificação do número ótimo de modos de Maxwell a serem considerados. Ao efetuar-se a comparação entre as técnicas, verificou-se o espectro discreto apresenta como um sistema melhor condicionado, permitindo assim obter maior confiabilidade dos parâmetros estimados. Também é proposta uma modificação da metodologia de determinação da DMM, em que é aplicada a quadratura de Gauss-Hermite para a resolução numérica da integral dos modelos de relaxação. / The molecular weight distribution (MWD) and its parameters are of the fundamental importance in the characterization of polymers. Therefore, the development of techniques for faster and less time consuming determination of the MWD is of great practical relevance. The goals of this work were the implementation of some of the relaxation models from double reptation theory proposed in the literature, the evaluation of these implementations and the analysis of two key points in the recovery of the MWD from rheological data which are the methodology for calculation of the relaxation spectrum based on the Maxwell model and the numeric strategy for the evaluation of the integrals appearing in the relaxation models. The inverse problem, i.e., the determination of the MWD from rheological data using a specified relaxation model and an imposed distribution function, was solved. In the analysis of the inverse problem, the Generalized Exponential (GEX) was used as distribution function and two approaches were considered: i) explicit calculation of the relaxation spectrum and ii) use of the parametric method proposed by Schwarzl to avoid the explicit calculation of the relaxation spectrum. In the test of commercial samples of polyethylene with polidispersity less than 10, the application of this methodology led to MWD curves which provided good fit of the experimental SEC data. Regarding the methodology for calculation of the relaxation spectrum, a comparison between the performance of discrete and continuous relaxation spectrum was performed and some possible a criteria to determine the appropriate number of relaxation modes of Maxwell to be used were evaluated. It was found that the technique of discrete spectrum leads to better conditioned systems and, consequently, greater reliability of the estimated parameters. With relation to the numeric strategy for the evaluation of the integrals appearing in the relaxation models, the use of Gauss-Hermite quadrature using a new change of variables was proposed.

京都大学 / 0048 / 新制・課程博士 / 博士(農学) / 甲第20449号 / 農博第2234号 / 新制||農||1050(附属図書館) / 学位論文||H29||N5070(農学部図書室) / 京都大学大学院農学研究科森林科学専攻 / (主査)教授 矢野 浩之, 教授 木村 恒久, 教授 髙野 俊幸 / 学位規則第4条第1項該当 / Doctor of Agricultural Science / Kyoto University / DFAM

No description available.