Global ETD Search

1	Modelling, Design, and Optimization of Membrane based Heat Exchangers for Low-grade Heat and Water Recovery Soleimanikutanaei, Soheil 20 September 2018 (has links) Transport Membrane Condenser (TMC) is an innovative technology based on the property of a nano-scale porous material which can extract both waste heat and water from exhaust gases. This technology tremendously improves the efficiency of boilers and gas/coal combustors by lowering waste heat and increasing water recovery. Contaminants in the flue gases, such as CO2, O2, NOx, and SO2 are inhibited from passing through the membrane by the membrane’s high selectivity. The condensed water through these tubes is highly pure and can be used as the makeup water for many industrial applications. The goal of this research is to investigate the heat transfer, condensation rate, pressure drop and overall performance of crossflow heat exchangers. In this research, a numerical model has been developed to predict condensation of water vapor over and inside of nano-porous layers. Both capillary condensation inside the nanoscale porous structure of the TMC and the surface condensation were considered in the proposed method using a semi-empirical model. The transport of the water vapor and the latent heat of condensation were applied in the numerical model using the pertinent mass, momentum, turbulence and energy equations. By using the proposed model and simulation procedure, the effect of various inlet parameters such as inlet mass flow rate, inlet temperature, and water vapor content of the inlet flow on the performance of the cross-flow TMC heat exchanger was studied to obtain the optimum performance of the heat exchangers at different working conditions. The performance of the TMC heat exchangers for inlet flue gas rate 40 to 120 kg/h, inlet water rate 60 to 140 kg/h, inlet flue gas relative humidity 20 to 90%, and tube pitch ratio 0.25 to 2.25 has been studied. The obtained results show that the water condensation flux continuously increases with the increase of the inlet flue-gas flow rate, water flow rate, and the flue-gas humidity. The total heat flux also follows the same trend due to the pronounced effect of the latent heat transfer from the condensation process. The water condensation flux and the overall heat transfer increase at the beginning for small values of the tube pitches and then decreases as the tube pitch increases furthermore. In addition to the cross-flow TMC heat exchangers, the performance of a shell and tube TMC heat exchanger for high pressure and temperature oxy-combustion applications has been investigated. The performance analysis for a 6-heat exchanger TMC unit shows that heat transfer of the 2-stage TMC unit is higher than the 2-stage with the same number of the heat exchanger in each unit. Transport membrane condenser Waste heat recovery Heat exchanger Tube bundles Ceramic nanoporous membrane Heat Transfer, Combustion
2	From Macro to Nano : Electrokinetic Transport and Surface Control Pardon, Gaspard January 2014 (has links) Today, the growing and aging population, and the rise of new global threats on human health puts an increasing demand on the healthcare system and calls for preventive actions. To make existing medical treatments more efficient and widely accessible and to prevent the emergence of new threats such as drug-resistant bacteria, improved diagnostic technologies are needed. Potential solutions to address these medical challenges could come from the development of novel lab-on-chip (LoC) for point-of-care (PoC) diagnostics. At the same time, the increasing demand for sustainable energy calls for the development of novel approaches for energy conversion and storage systems (ECS), to which micro- and nanotechnologies could also contribute. This thesis has for objective to contribute to these developments and presents the results of interdisciplinary research at the crossing of three disciplines of physics and engineering: electrokinetic transport in fluids, manufacturing of micro- and nanofluidic systems, and surface control and modification. By combining knowledge from each of these disciplines, novel solutions and functionalities were developed at the macro-, micro- and nanoscale, towards applications in PoC diagnostics and ECS systems. At the macroscale, electrokinetic transport was applied to the development of a novel PoC sampler for the efficient capture of exhaled breath aerosol onto a microfluidic platform. At the microscale, several methods for polymer micromanufacturing and surface modification were developed. Using direct photolithography in off-stoichiometry thiol-ene (OSTE) polymers, a novel manufacturing method for mold-free rapid prototyping of microfluidic devices was developed. An investigation of the photolithography of OSTE polymers revealed that a novel photopatterning mechanism arises from the off-stoichiometric polymer formulation. Using photografting on OSTE surfaces, a novel surface modification method was developed for the photopatterning of the surface energy. Finally, a novel method was developed for single-step microstructuring and micropatterning of surface energy, using a molecular self-alignment process resulting in spontaneous mimicking, in the replica, of the surface energy of the mold. At the nanoscale, several solutions for the study of electrokinetic transport toward selective biofiltration and energy conversion were developed. A novel, comprehensive model was developed for electrostatic gating of the electrokinetic transport in nanofluidics. A novel method for the manufacturing of electrostatically-gated nanofluidic membranes was developed, using atomic layer deposition (ALD) in deep anodic alumina oxide (AAO) nanopores. Finally, a preliminary investigation of the nanopatterning of OSTE polymers was performed for the manufacturing of polymer nanofluidic devices. / <p>QC 20140509</p> / Rappid / NanoGate / Norosensor microsystem nanosystem microfluidic nanofluidic surface modification surface property electrokinetics model simulation material polymer thiol-ene microfabrication nanofabrication micromanufacturing nanomanufacturing breath sampling aerosol precipitation corona discharge electrostatic precipitation grafting chemistry click chemistry nanopore nanoporous membrane photolithography photopatterning photografting microfluidics nanofluidics oste OSTE+ OSTEmer lab-on-chip loc point-of-care poc biocompatibility diagnostics breath analysis fuel cell
3	Multimode Analysis of Nanoscale Biomolecular Interactions Tiwari, Purushottam Babu 25 February 2015 (has links) Biomolecular interactions, including protein-protein, protein-DNA, and protein-ligand interactions, are of special importance in all biological systems. These interactions may occer during the loading of biomolecules to interfaces, the translocation of biomolecules through transmembrane protein pores, and the movement of biomolecules in a crowded intracellular environment. The molecular interaction of a protein with its binding partners is crucial in fundamental biological processes such as electron transfer, intracellular signal transmission and regulation, neuroprotective mechanisms, and regulation of DNA topology. In this dissertation, a customized surface plasmon resonance (SPR) has been optimized and new theoretical and label free experimental methods with related analytical calculations have been developed for the analysis of biomolecular interactions. Human neuroglobin (hNgb) and cytochrome c from equine heart (Cyt c) proteins have been used to optimize the customized SPR instrument. The obtained Kd value (~13 µM), from SPR results, for Cyt c-hNgb molecular interactions is in general agreement with a previously published result. The SPR results also confirmed no significant impact of the internal disulfide bridge between Cys 46 and Cys 55 on hNgb binding to Cyt c. Using SPR, E. coli topoisomerase I enzyme turnover during plasmid DNA relaxation was found to be enhanced in the presence of Mg2+. In addition, a new theoretical approach of analyzing biphasic SPR data has been introduced based on analytical solutions of the biphasic rate equations. In order to develop a new label free method to quantitatively study protein-protein interactions, quartz nanopipettes were chemically modified. The derived Kd (~20 µM) value for the Cyt c-hNgb complex formations matched very well with SPR measurements (Kd ~16 µM). The finite element numerical simulation results were similar to the nanopipette experimental results. These results demonstrate that nanopipettes can potentially be used as a new class of a label-free analytical method to quantitatively characterize protein-protein interactions in attoliter sensing volumes, based on a charge sensing mechanism. Moreover, the molecule-based selective nature of hydrophobic and nanometer sized carbon nanotube (CNT) pores was observed. This result might be helpful to understand the selective nature of cellular transport through transmembrane protein pores. Biomolecular interactions Heme proteins DNA topoisomerases DNA supercoiling Surface plasmon resonance (SPR) SPR data fitting Quartz nanopipettes label-free methods Finite element simulations Analytical Chemistry Biochemistry Biological and Chemical Physics Biophysics Biotechnology Condensed Matter Physics Molecular Biology Physics

1

Page generated in 0.093 seconds