Polymeric membranes exhibit a trade-off between permeability and selectivity in gas separations which limits their viability as an economically feasible post-combustion carbon capture technology. One approach to improve the separation properties of polymeric membranes is the inclusion of particulate materials into the polymer matrix to create what are known as mixed matrix membranes (MMMs). By combining the polymer and particulate phases, beneficial properties of both can be seen in the resulting composite material. One of the most notable challenges in producing mixed matrix membranes is in the formation of performance-hindering defects at the polymer-filler interface. Non-selective voids or polymer chain rigidification are but two non-desirable effects which can be observed. The material selection and synthesis route are key to minimising these defects. Thin membranes are also highly desirable to achieve greater gas fluxes and improved economical separation processes. Hence smaller nano-sized particles are of particular interest to minimise the disruption to the polymer matrix. This is a challenge due to the tendency of some small particles to form agglomerations. This work involved introducing novel nanoscale filler particles into PEBAX MH1657, a commercially available block-copolymer consisting of poly(ethylene oxide) and nylon 6 chains. Poly(ether-b-amide) materials possess an inherently high selectivity for the CO2/N2 separation due to polar groups in the PEO chain but suffer from low permeabilities. Mixed matrix membranes were fabricated with PEBAX MH1657 primarily using two filler particles, nanoscale ZIF-8 and novel nanoscale MCM-41 hollow spheres. This work primarily investigated the effects of the filler loading on both the morphology and gas transport properties of the composite materials. The internal structure of the membranes was examined using scanning electron microscopy (SEM), and the gas transport properties determined using a bespoke time-lag gas permeation apparatus. ZIF-8 is a zeolitic imidazolate framework which possesses small pore windows that may favour CO2 transport over that of N2. ZIF-8-PEBAX membranes were successfully synthesised up to 7wt.%. It was found that for filler loadings below 5wt.%, the ZIF-8 was well dispersed within the polymer phase. At these loadings modest increases in the CO2 permeability coeffcient of 0-20% compared to neat PEBAX were observed. Above this 5wt.% loading large increases in both CO2, N2 and He permeability coeffcients coincided with the presence of large micron size clusters formed of hundreds of filler ZIF-8 particles. The increases in permeability were attributed to voids observed within the clusters. MCM-41 is a metal organic framework that has seen notable interest in the field of carbon capture, due to its tunable pore size and ease of functionalisation. Two types of novel MCM-41 hollow sphere (MCM-41-HS) of varying pore size were incorporated into PEBAX and successfully used to fabricate MMMs up to 10wt.%. SEM showed the MCM-41 generally interacted well with the polymer with no signs of voids and was generally well dispersed. However, some samples of intermediate loading in both cases showed highly asymmetric distribution of nanoparticles and high particle density regions near one external face of the membrane which also showed the highest CO2 permeability coeffcients. It is suspected that these high permeabilities are due to the close proximity of nanoparticles permitting these regions to act in a similar way to percolating networks. It was determined that there was no observable effect of the varying pore size which was expected given the transport in the pores should be governed by Knudsen diffusion.

Les propriétés des matériaux découlent en partie de leur organisation à l’échelle nano ou microscopique. Dans cette thèse, on montre qu’en contrôlant la chimie aux interfaces, des organisations très régulières peuvent être obtenus spontanément dans divers matériaux polymères.Dans une première, la chimie supramoléculaire a été utilisée pour contrôler l’organisation en masse de polymères greffés à une ou deux de leurs extrémités par la thymine (Thy) ou la 2,6-diamino-1,3,5-triazine (DAT), deux unités supramoléculaires complémentaires s’associant par liaisons hydrogène. Quelque soit la nature de la chaine polymère (PE, PDMS, PPG), les matériaux présentent des organisations lamellaires nanoscopiques très régulières lorsque l’unité terminale (Thy) et/ou la chaine (PE) cristallisent. Les contributions respectives à ces organisations de la ségrégation de phase, de la cristallisation, des liaisons supramoléculaires et des interactions secondaires ont été déterminées. Il a été montré que le confinement des chaines polymères dans les lamelles empêche la formation de chaines de grandes masses molaires. Cependant, les interactions supramoléculaires Thy/DAT permettent de former des copolymères à blocs supramoléculaires en mélangeant des chaines incompatibles fonctionnalisées par ces unités.Dans une seconde partie, nous avons montré que la texturation spontanée de films acrylates photopolymérisés à l’air est gouvernée à l’interface formulation/air par l’équilibre des cinétiques de polymérisation et d’inhibition par l’oxygène. Des morphologies microscopiques très régulières, hexagonales, lamellaires ou cacahuètes, sont obtenues en contrôlant différents paramètres expérimentaux et ce pour une large gamme d’épaisseur de film (6 µm – 2 mm). L’auto-texturation confère aux films des propriétés optiques singulières (flou, clarté) qui peuvent être modulées en ajustant les caractéristiques de la morphologie. / Materials properties very often derive from their nano or micro-scale organization. In this thesis, we evidence that controlling the chemistry at the interfaces allows obtaining spontaneously very regular organizations in various polymer materials.In the first part, supramolecular chemistry has been used to control the organization in the bulk of polymer grafted at one or both extremities by thymine (Thy) or 2,6-diamino-1,3,5-triazine (DAT), two self-complementary supramolecular units interacting via hydrogen bonds. Whatever the polymer nature (PE, PDMS, PPG), materials present very regular nanoscale long-range ordered lamellar organizations if the end group crystallize (Thy) and/or the chain crystallize (PE). Respective contributions to these organizations of phase segregation, crystallization, supramolecular interactions and secondary interactions have been determined. It was shown that the confinement of chains in lamellae prevent the formation of high molecular weight chains, resulting in poor mechanical properties. However, Thy/DAT interactions allow creating supramolecular block copolymers by mixing incompatible chains functionalized with these units.In the second part, we have studied the spontaneous formation of patterns at the film surface of acrylate film during their photopolymerization under air. This phenomenon occurs if there is a balance at the film surface between the polymerization and the oxygen inhibition rates. Very regular microscale patterns (hexagons, lamellae, peanuts) have been generated by controlling some experimental parameters (UV intensity, initiator concentration) for a wide range of film thicknesses (6 µm – 2 mm). Self-patterning gives interesting optical properties to the films (haze, clarity) which can be modulated by adjusting the patterns wavelength and amplitude.

Excess Fluoride in drinking water is a cause for concern in several countries in the world. Various techniques have been developed to mitigate the harmful effects of fluoride. In the present work, a combined alum and activated alumina (AA) process has been investigated. Tap water with sodium fluoride dissolved in it to produce a solution having a fluoride concentration of 5 mg/L was used as the feed. It was found that pretreatment with alum extends the time required for the regeneration of the AA column. The volume of water treated increased by 89% compared to AA process alone. Though the regeneration of the AA column has been well documented, subtle issues have ot been reported. The disposal of regeneration effluent is a concern in adsorption-based processes. This study aims to examine some of the issues involved in the regeneration of the AA column such as disposal of effluent, and the quantity of acid and alkali required. The regeneration effluent from the combined process, which had a fluoride concentration of 10-16 mg/L was treated in a solar still. The distillate from the still had a fluoride concentration of 2-3 mg/L, which is much lower than the concentration of the regeneration effluent. The cost of treatment decreased with each regeneration cycle and after four regenerations the cost was Rs 0.5/L of treated water. The volume of water treated after four regenerations was 307 L/Kg of AA. Studies were also done using field water from Banavara, Hassan district, Karnataka, which had a fluoride concentration of 3,0-3.5 mg/L. The combined process successfully produced treated water having an acceptable fluoride concentration. After one regeneration cycle, the operating cost was Rs. 1/L of treated water. Studies have also been conducted on a point-of-use water filter containing a bed of AA pellets. The filter was provided by an organization called TIDE. The present results appear to suggest that a column with a smaller diameter than the TIDE filter has a better removal capacity. Ceramic candles are widely used for water filtration as they are readily available and inexpensive. Hence they are suitable for household water treatment purposes. In the present work, ceramic candles have been impregnated with nano-size alumina and nano-size magnesium oxide and tested for their defluoridation capacity. The nanoparticles were generated in situ in the pores of the candle by solution combustion synthesis. It has been found the candle impregnated with nano-size magnesium oxide has a higher defluoridation capacity than nano-size alumina. Estimation of the particle size in the samples of treated water did not give conclusive evidence for the presence or absence of nanoparticles. The volume of water treated was low and the cost of treatment was high (Rs. 12/L for the candle impregnated with MgO). Hence such candles are unsuitable for defluoridation. Batch adsorption has been employed to measure the adsorption capacity of adsorbents. A model to capture the overall picture of the batch adsorption process, obtaining the kinetic and transport parameters involved has been developed. The mathematical model takes into account external mass transfer resistance, intraparticle diffusion, adsorption, and desorption. The equilibrium adsorption data was fitted using the Langmuir isotherm. The governing equations were solved using a finite difference technique known as the Laasonen method. The parameters were estimated by fitting two sets of data using a MATLAB function. The values estimated suggest that the adsorption process may not be diffusion-limited, in contrast to the assumption commonly used in the literature. The estimated parameter values were used to predict the concentration profiles for the other data sets. It was found that predicted and measured profiles agreed reasonably well.

The mechanisms of thermal transport in defect-free silicon nanostructures are examined using a combination of lattice dynamics (LD) calculations and the Boltzmann transport equation (BTE). To begin, the thermal conductivity reduction in thin films is examined using a hierarchical method that first predicts phonon transport properties using LD calculations, and then solves the phonon BTE using the lattice Boltzmann method. This approach, which considers all of the phonons in the first Brillouin-zone, is used to assess the suitability of common assumptions used to reduce the computational effort. Specifically, we assess the validity of: (i) neglecting the contributions of optical modes, (ii) the isotropic approximation, (iii) assuming an averaged bulk mean-free path (i.e., the Gray approximation), and (iv) using the Matthiessen rule to combine the effect of different scattering mechanisms. Because the frequency-dependent contributions to thermal conductivity change as the film thickness is reduced, assumptions that are valid for bulk are not necessarily valid for thin films. Using knowledge gained from this study, an analytical model for the length-dependence of thin film thermal conductivity is presented and compared to the predictions of the LD-based calculations. The model contains no fitting parameters and only requires the bulk lattice constant, bulk thermal conductivity, and an acoustic phonon speed as inputs. By including the mode-dependence of the phonon lifetimes resulting from phonon-phonon and phonon-boundary scattering, the model predictions capture the approach to the bulk thermal conductivity better than predictions made using Gray models based on a single lifetime. Both the model and the LD-based method are used to assess a procedure commonly used to extract bulk thermal conductivities from length-dependent molecular dynamics simulation data. Because the mode-dependence of thermal conductivity is not included in the derivation of this extrapolation procedure, using it can result in significant error. Finally, phonon transport across a silicon/vacuum-gap/silicon structure is modelled using lattice dynamics and Landauer theory. The phonons transmit thermal energy across the vacuum gap via atomic interactions between the leads. Because the incident phonons do not encounter a classically impenetrable potential barrier, this mechanism is not a tunneling phenomenon. The heat flux due to phonon transport can be 4 orders of magnitude larger than that due to photon transport predicted from near-field radiation theory.

Nanoscale communication is appealing domain in nanotechnology. There are many existing nanoscale communication methods. In addition to these, novel techniques can be derived depending on the naturally existing phenomena such as molecular communication. It uses molecules as an information carrier such as molecular motors, pheromones and neurotransmitters for neuro-spike communication. Among them, neuro-spike communication is a vastly unexplored area. The ultimate goal of this thesis is to accurately investigate it by obtaining a realistic physical channel model. This model can be exploited in different disciplines. Furthermore, the model can help designing novel artificial nanoscale communication paradigms. The modeled channel is analyzed regarding the error probability of detecting spikes depending on channel parameters. Moreover, channel delay is characterized and information theoretical analysis of packet release mechanism in the channel is performed. The modeled channel is extended to multi-input single output terminal. In this case, input neurons can simultaneously send information through the same synapse leading to interference. However, there is an interference repressing technique in these synapses called automatic gain control. It decreases the interference level observed on weaker signal. The first aim for this case is to define the interference channel at synapse having automatic gain control. The second aim is to analyze the achievable rate region of this channel. The analysis shows that gain control mechanism prevents the decrease in achievable rate region because of the weaker signal. Moreover, power, firing rate and number of stronger inputs do not affect the achievable rate region.

In recent years, coinage metal nanoparticles have emerged as materials with largest quadratic optical nonlinearity. Their first hyperpolarizabilities (β) are very high (105-106 x 10-30 esu) but such large values were quite unexpected because of their apparently centrosymmetric bulk structure. Only a small second harmonic generation (SHG) from coinage metal nanoparticles is expected through higher order multipolar (e.g., quadrupolar) polarization mechanisms. Various possible reasons have been attributed to the observation of large β values in coinage metal nanoparticles. They are: 1) Particles may not be overall centrosymmetric (as appears from the TEM pictures) which, in turn, can make SHG electric dipole allowed, 2) Several polarization mechanisms (dipolar, quadrupolar, retardation, etc.) may be operating simultaneously to render SHG very efficient, 3) SHG can be resonance enhanced if the incident or SH photons fall within the surface plasmon resonance (SPR) absorption bands or higher energy interband transitions in the metal particles, and 4) Surface capping agents used for stabilization of the nanoparticles in solution alter the SH response. It is, therefore, important to experimentally find out which of the above mentioned possibilities are dominant and under what conditions we can identify the contribution of various mechanisms to the overall SHG response of the coinage metal nanoparticles. In this thesis work, the origin of SHG from copper (one of the coinage metals) nanoparticles has been investigated using hyper-Rayleigh scattering (HRS). In chapter 1, an introduction to metal nanoparticles and their optical properties have been presented. A general introduction to second order nonlinear optics and various methods for the determination of first hyperpolarizability are provided. A literature survey on the second order NLO properties of metal nanoparticles is also done. At the end of the chapter, the motivation of the work done is outlined. In chapter 2, the experimental set-ups for unpolarized and polarization resolved hyper-Rayleigh scattering (HRS) measurements at different wavelengths are described. Generation of IR wavelength of 1543 and 1907 nm using stimulated Raman scattering in gases have been presented in this chapter. In chapter 3, synthesis and characterization of copper nanoparticles are described. Four different size copper nanoparticles (5, 9, 25, and 55 nm) were prepared by laser ablation. Size dependencies of first hyperpolarizability were investigated at different wavelengths and it was found that β increases with increasing size of the particle and that the SHG originates mainly from the surface of the particle. Dispersion in first hyperpolarizabilities of the copper nanoparticles has also been investigated and we find that at incident and SH wavelengths far from the SPR absorption band, the hyperpolarizability is large compared to molecular hyperpolarizabilities. In chapter 4, the results of polarization resolved HRS measurements on copper nanoparticles of five different sizes at four different wavelengths (738, 1064, 1543 and 1907 nm) are reported. Polarization analyses show that at small particle size to wavelength (d/λ) ratio the dipolar contribution to SHG is dominant whereas the quadrupolar and retardation effects become important at larger d/λ values. The “small particle limit” in the SHG from coinage metal nanoparticles has been assessed based on our results on copper and others’ results on silver and gold nanoparticles. In chapter 5, the effect of surface capping on the first hyperpolarizability of copper nanoparticles is investigated. Polyvinyl pyrrolidone (PVP) has been used as a capping agent. The results obtained for bare and capped copper nanoparticles show that capping enhances the hyperpolarizability by a factor of 2. In the last chapter 6, general conclusions drawn on SHG from coinage metal nanoparticles based on this work are presented along with future perspectives.

This dissertation presents thermal and thermoelectric measurements of nanostructures. Because the characteristic size of these nanostructures is comparable to and even smaller than the mean free paths or wavelengths of electrons and phonons, the classical constitutive laws such as the Fourier’s law cannot be applied. Three types of nanostructures have been investigated, including nanoscale constrictions patterned in a sub-100 nm thick silicon film, monatomic thick graphene ribbons supported on a silicon dioxide (SiO₂) beam, and indium antimonide (InSb) nanowires. A suspended measurement device has been developed to measure the thermal resistance of 48-174 nm wide constrictions etched in 35-65 nm thick suspended silicon membranes. The measured thermal resistance is more than ten times larger than the diffusive thermal resistance calculated from the Fourier’s law. The discrepancy is attributed to the ballistic thermal resistance component as a result of the smaller constriction width than the phonon-phonon scattering mean free path. Because of diffuse phonon scattering by the side walls of the constriction with a finite length, the phonon transmission coefficient is 0.015 and 0.2 for two constrictions of 35 nm x 174 nm x220 nm and 65 nm x 48 nm x 50 nm size. Another suspended device has been developed for measuring the thermal conductivity of single-layer graphene ribbons supported on a suspended SiO₂ beam. The obtained room-temperature thermal conductivity of the supported graphene is about 600 W/m-K, which is about three times smaller than the basal plane values of high-quality pyrolytic graphite because of phonon-substrate scattering, but still considerably higher than for common thin film electronic materials. The measured thermal conductivity is in agreement with a theoretical result based on quantum mechanical calculation of the threephonon scattering processes in graphene, which finds a large contribution to the thermal conductivity from the flexural vibration modes. A device has been developed to measure the Seebeck coefficients (S) and electrical conductivities ([sigma]) of InSb nanowires grown by a vapor-liquid-solid process. The obtained Seebeck coefficient is considerably lower than the literature values for bulk InSb crystals. It was further found that decreasing the base pressure during the VLS growth results in an increase in the Seebeck coefficient and a decrease in the electrical conductivity, except for a nanowire with the smallest diameter of 15 nm. This trend is attributed to preferential oxidation of indium by residual oxygen in the growth environment, which could cause increased n-type Sb doping of the nanowires with increasing base pressure. The deviation in the smallest diameter nanowire from this trend indicates a large contribution from the surface charge states in the nanowire. The results suggest that better control of the chemical composition and surface states is required for improving the power factor of InSb nanowires. On approach is to use Indium-rich source materials for the growth to compensate for the loss of indium due to oxidation by residual oxygen. / text

The osteocytes are the most abundant and longest living bone cells, embedded in the bone matrix. They are interconnected with each other through dendrites, located in slender canals called canaliculi. The osteocyte lacunae, cavities in which the cells are located, together with the canaliculi form a communication network throughout the bone matrix, permitting transport of nutrients, waste and signals. These cells were firstly considered passive, but lately it has become increasingly clear their role as mechanosensory cells and orchestrators of bone remodeling. Despite recent advances in imaging techniques, none of the available methods can provide an adequate 3D assessment of the lacuno-canalicular network (LCN). The aims of this thesis were to achieve 3D imaging of the LCN with synchrotron radiation X-ray computed tomography (SR-CT) and to develop tools for 3D detection and segmentation of this cell network, leading towards automatic quantification of this structure. We demonstrate the feasibility of parallel beam SR-CT to image in 3D the LCN (voxel~300 nm). This technique can provide data on both the morphology of the cell network and the composition of the bone matrix. Compared to the other 3D imaging methods, this enables imaging of tissue covering a number of cell lacunae three orders of magnitude greater, in a simpler and faster way. This makes possible the study of sets of specimens in order to reach biomedical conclusions. Furthermore, we propose the use of divergent holotomography, to image the ultrastructure of bone tissue (voxel~60 nm). The image reconstruction provides phase maps, obtained after the application of a suitable phase retrieval algorithm. This technique permits assessment of the cell network with higher accuracy and it enables the 3D organization of collagen fibres organization in the bone matrix, to be visualized for the first time. In order to obtain quantitative parameters on the geometry of the cell network, this has to be segmented. Due to the limitations in spatial resolution, canaliculi appear as 3D tube-like structures measuring only 1-3 voxels in diameter. This, combined with the noise, the low contrast and the large size of each image (8 GB), makes the segmentation a difficult task. We propose an image enhancement method, based on a 3D line filter combined with bilateral filtering. This enables improvement in canaliculi detection, reduction of the background noise and cell lacunae preservation. For the image segmentation we developed a method based on variational region growing. We propose two expressions for energy functionals to minimize in order to detect the desired structure, based on the 3D line filter map and the original image. Preliminary quantitative results on human femoral samples are obtained based on connected components analysis and a few observations related to the bone cell network and its relation with the bone matrix are presented.

The aim of the study presented in this thesis is to explore the electrical and physical properties of films of tin and lead clusters. Understanding the novel conductance properties of cluster films and related phenomenon such as coalescence is important to fabricate any cluster based devices. Coalescence is an important phenomenon in metallic cluster films. Due to coalescence the morphology of the films changes with time which changes their properties and could lead to failure in cluster devices. Coalescence is studied in Sn and Pb cluster films deposited on Si$_3$N$_4$ surfaces using Ultra High Vacuum (UHV) cluster deposition system. The conductance of the overall film is linked to the conductance of the individual necks between clusters by simulations. It is observed that the coalescence process in Sn and Pb films follows a power law in time with an exponent smaller than reported in literature. These results are substantiated by the results from previous experimental and Kinetic Monte Carlo (KMC) simulation studies at UC. Percolating films of Sn show unique conductance properties. These films are characterized using various electrode configurations, applied voltages and temperatures. The conductance measurements are performed by depositing clusters on prefabricated gold electrodes on top of Si$_3$N$_4$ substrates. Sn cluster films exhibit a variety of conductance behaviours during and after the end of deposition. It is observed that the evolution of conductance during the onsets at percolation threshold is dependent on the film morphology. Samples showing difference responses in onset also behave differently after the end of deposition. Therefore all samples were categorized according to their onset behaviour. After the end of deposition, when a bias voltage is applied, the conductance of Sn films steps up and down between various well-defined conductance levels. It is also observed that in many cases the conductance levels between which these devices jump are close to integral multiples of the conductance quantum. There are many possible explanations for the steps in conductance. One of the explanations is formation and breaking of conducting paths in the cluster films by electric field induced evaporation and electromigration respectively. The stepping behaviour is similar to that in non-volatile memory devices and hence very interesting to explore due to potential applications.

This dissertation focuses on near-field radiative transfer, which can be defined as the discipline concerned with energy transfer via electromagnetic waves at sub-wavelength distances. Three specific subjects related to this discipline are investigated, namely nearfield thermal radiation, nanoscale-gap thermophotovoltaic (nano-TPV) power generation and optical characterization. An algorithm for the solution of near-field thermal radiation problems in one-dimensional layered media is developed, and several tests are performed showing the accuracy, consistency and versatility of the procedure. The possibility of tuning near-field radiative heat transfer via thin films supporting surface phononpolaritons (SPhPs) in the infrared is afterwards investigated via the computation of the local density of electromagnetic states and the radiative heat flux between two films. Results reveal that due to SPhP coupling, fine tuning of near-field radiative heat transfer is possible by solely varying the structure of the system, the structure being the film thicknesses and their distance of separation. The coexistence of two regimes of near-field thermal radiation between two thin films of silicon carbide is demonstrated via numerical simulations and an asymptotic analysis of the radiative heat transfer coefficient. The impacts of thermal effects on the performances of nano-TPV power generators are investigated via the solution of the coupled near-field thermal radiation, charge and heat transport problem. The viability of nano-TPV devices proposed so far in the literature, based on a tungsten radiator at 2000 K and indium gallium antimonide cell, is questioned due to excessive heating of the junction converting thermal radiation into electricity. Using a convective thermal management system, a heat transfer coefficient as high as 105 Wm-2K-1 is required to maintain the junction at room temperature. The possibility of characterizing non-intrusively, and potentially in real-time, nanoparticles from 5 nm to 100 nm in size via scattered surface wave is explored. The feasibility of the characterization framework is theoretically demonstrated via a sensitivity analysis of the scattering matrix elements. Measurements of the scattering matrix elements for 200 nm and 50 nm gold spherical particles show the great sensitivity of the characterization tool, although an ultimate calibration is difficult with the current version of the experimental set-up.