Spelling suggestions: "subject:"none dataneeded"" "subject:"none dataprovided""
1 |
Bayesian Recovery of Clipped OFDM Signals: A Receiver-based ApproachAl-Rabah, Abdullatif R. 05 1900 (has links)
Recently, orthogonal frequency-division multiplexing (OFDM) has been adopted for high-speed wireless communications due to its robustness against multipath fading. However, one of the main fundamental drawbacks of OFDM systems is the high peak-to-average-power ratio (PAPR). Several techniques have been proposed for PAPR reduction. Most of these techniques require transmitter-based (pre-compensated) processing. On the other hand, receiver-based alternatives would save the power and reduce the transmitter complexity. By keeping this in mind, a possible approach is to limit the amplitude of the OFDM signal to a predetermined threshold and equivalently a sparse clipping signal is added. Then, estimating this clipping signal at the receiver to recover the original signal. In this work, we propose a Bayesian receiver-based low-complexity clipping signal recovery method for PAPR reduction. The method is able to i) effectively reduce the PAPR via simple clipping scheme at the transmitter side, ii) use Bayesian recovery algorithm to reconstruct the clipping signal at the receiver side by measuring part of subcarriers, iii) perform well in the absence of statistical information about the signal (e.g. clipping level) and the noise (e.g. noise variance), and at the same time iv is energy efficient due to its low complexity. Specifically, the proposed recovery technique is implemented in data-aided based. The data-aided method collects clipping information by measuring reliable
data subcarriers, thus makes full use of spectrum for data transmission without the
need for tone reservation. The study is extended further to discuss how to improve the recovery of the clipping signal utilizing some features of practical OFDM systems i.e., the oversampling and the presence of multiple receivers. Simulation results demonstrate the superiority of the proposed technique over other recovery algorithms. The overall objective is to show that the receiver-based Bayesian technique is highly recommended to be an effective and practical alternative to state-of-art PAPR reduction techniques.
|
2 |
Carrier Frequency Offset Estimation for Orthogonal Frequency Division MultiplexingChallakere, Nagaravind 01 May 2012 (has links)
This thesis presents a novel method to solve the problem of estimating the carrier frequency set in an Orthogonal Frequency Division Multiplexing (OFDM) system. The approach is based on the minimization of the probability of symbol error. Hence, this approach is called the Minimum Symbol Error Rate (MSER) approach. An existing approach based on Maximum Likelihood (ML) is chosen to benchmark the performance of the MSER-based algorithm. The MSER approach is computationally intensive. The thesis evaluates the approximations that can be made to the MSER-based objective function to make the computation tractable. A modified gradient function based on the MSER objective is developed which provides better performance characteristics than the ML-based estimator. The estimates produced by the MSER approach exhibit lower Mean Squared Error compared to the ML benchmark. The performance of MSER-based estimator is simulated with Quaternary Phase Shift Keying (QPSK) symbols, but the algorithm presented is applicable to all complex symbol constellations.
|
3 |
Carrier frequency offset recovery for zero-IF OFDM receiversMitzel, Michael 13 February 2009
As trends in broadband wireless communications applications demand faster development cycles, smaller sizes, lower costs, and ever increasing data rates, engineers continually seek new ways to harness evolving technology. The zero intermediate frequency receiver architecture has now become popular as it has both economic and size advantages over the traditional superheterodyne architecture.<p>
Orthogonal Frequency Division Multiplexing (OFDM) is a popular multi-carrier modulation technique with the ability to provide high data rates over echo ladened channels. It has excellent robustness to impairments caused by multipath, which includes frequency selective fading. Unfortunately, OFDM is very sensitive to the carrier frequency offset (CFO) that is introduced by the downconversion process. The objective of this thesis is to develop and to analyze an algorithm for blind CFO recovery suitable for use with a practical zero-Intermediate Frequency (zero-IF) OFDM telecommunications system.<p>
A blind CFO recovery algorithm based upon characteristics of the received signal's power spectrum is proposed. The algorithm's error performance is mathematically analyzed, and the theoretical results are verified with simulations. Simulation shows that the performance of the proposed algorithm agrees with the mathematical analysis.<p>
A number of other CFO recovery techniques are compared to the proposed algorithm. The proposed algorithm performs well in comparison and does not suffer from many of the disadvantages of existing blind CFO recovery techniques. Most notably, its performance is not significantly degraded by noisy, frequency selective channels.
|
4 |
Carrier frequency offset recovery for zero-IF OFDM receiversMitzel, Michael 13 February 2009 (has links)
As trends in broadband wireless communications applications demand faster development cycles, smaller sizes, lower costs, and ever increasing data rates, engineers continually seek new ways to harness evolving technology. The zero intermediate frequency receiver architecture has now become popular as it has both economic and size advantages over the traditional superheterodyne architecture.<p>
Orthogonal Frequency Division Multiplexing (OFDM) is a popular multi-carrier modulation technique with the ability to provide high data rates over echo ladened channels. It has excellent robustness to impairments caused by multipath, which includes frequency selective fading. Unfortunately, OFDM is very sensitive to the carrier frequency offset (CFO) that is introduced by the downconversion process. The objective of this thesis is to develop and to analyze an algorithm for blind CFO recovery suitable for use with a practical zero-Intermediate Frequency (zero-IF) OFDM telecommunications system.<p>
A blind CFO recovery algorithm based upon characteristics of the received signal's power spectrum is proposed. The algorithm's error performance is mathematically analyzed, and the theoretical results are verified with simulations. Simulation shows that the performance of the proposed algorithm agrees with the mathematical analysis.<p>
A number of other CFO recovery techniques are compared to the proposed algorithm. The proposed algorithm performs well in comparison and does not suffer from many of the disadvantages of existing blind CFO recovery techniques. Most notably, its performance is not significantly degraded by noisy, frequency selective channels.
|
5 |
Modulation and Synchronization for Aeronautical TelemetryShaw, Christopher G. 14 March 2014 (has links) (PDF)
Aeronautical telemetry systems have historically been implemented with constant envelope modulations like CPM. Shifts in system constraints including reduced available bandwidth and increased throughput demands have caused many in the field to reevaluate traditional methods and design practices. This work examines the costs and benefits of using APSK for aeronautical telemetry instead of CPM. Variable rate turbo codes are used to improve the power efficiency of 16- and 32-APSK. Spectral regrowth in nonlinear power amplifiers when driven by non-constant envelope modulation is also considered. Simulation results show the improved spectral efficiency of this modulation scheme over those currently defined in telemetry standards. Additionally, the impact of transitioning from continuous transmission to burst-mode is considered. Synchronization loops are ineffective in burst-mode communication. Data-aided feed forward algorithms can be used to estimate offsets in carrier phase, frequency, and symbol timing between the transmitter and the receiver. If a data-aided algorithm is used, a portion of the transmitted signal is devoted to a known sequence of pilot symbols. Optimum pilot sequences for the three synchronization parameters are obtained analytically and numerically for different system constraints. The alternating sequence is shown to be optimal given a peak power constraint. Alternatively, synchronization can be accomplished using blind algorithms that do not rely on a priori knowledge of a pilot sequence. If blind algorithms are used, the observation interval can be longer than for data-aided algorithms. There are combinations of pilot sequence length and packet length where data-aided algorithms perform better than blind algorithms and vice versa. The conclusion is that a sequential arrangement of blind algorithms operating over an entire burst performs better than a CRB-achieving data-aided algorithm operating over a short pilot sequence.
|
6 |
The realization of signal processing methods and their hardware implementation over multi-carrier modulation using FPGA technology : validation and implementation of multi-carrier modulation on FPGA, and signal processing of the channel estimation techniques and filter bank architectures for DWT using HDL coding for mobile and wireless applicationsMigdadi, Hassan Saleh Okleh January 2015 (has links)
First part of this thesis presents the design, validation, and implementation of an Orthogonal Frequency Division Multiplexing (OFDM) transmitter and receiver on a Cyclone II FPGA chip using DSP builder and Quartus II high level design tools. The resources in terms of logical elements (LE) including combinational functions and logic registers allocated by the model have been investigated and addressed. The result shows that implementing the basic OFDM transceiver allocates about 14% (equivalent to 6% at transmitter and 8% at receiver) of the available LE resources on an Altera Cyclone II EP2C35F672C6 FPGA chip, largely taken up by the FFT, IFFT and soft decision encoder. Secondly, a new wavelet-based OFDM system based on FDPP-DA based channel estimation is proposed as a reliable ECG Patient Monitoring System, a Personal Wireless telemedicine application. The system performance for different wavelet mothers has been investigated. The effects of AWGN and multipath Rayleigh fading channels have also been studied in the analysis. The performances of FDPP-DA and HDPP-DA-based channel estimations are compared based on both DFT-based OFDM and wavelet-based OFDM systems. The system model was studied using MATLAB software in which the average BER was addressed for randomized data. The main error differences that reflect the quality of the received ECG signals between the reconstructed and original ECG signals are established. Finally a DA-based architecture for 1-D iDWT/DWT based on an OFDM model is implemented for an ECG-PMS wireless telemedicine application. In the portable wireless body transmitter unit at the patient site, a fully Serial-DA-based scheme for iDWT is realized to support higher hardware utilization and lower power consumption; whereas a fully Parallel-DA-based scheme for DWT is applied at the base unit of the hospital site to support a higher throughput. It should be noted that the behavioural level of HDL models of the proposed system was developed and implemented to confirm its correctness in simulation. Then, after the simulation process the design models were synthesised and implemented for the target FPGA to confirm their validation.
|
7 |
Design and prototyping of indoor positioning systems for Internet-of-Things sensor networksShakoori Moghadam Monfared, Shaghayegh 04 January 2021 (has links) (PDF)
Accurate indoor positioning of narrowband Internet-of-Things (IoT) sensors has drawn more attention in recent years. The introduction of Bluetooth Low Energy (BLE) technology is one of the latest developments of IoT and especially applicable for Ultra-Low Power (ULP) applications. BLE is an attractive technology for indoor positioning systems because of its low-cost deployment and reasonable accuracy. Efficient indoor positioning can be achieved by deducing the sensor position from the estimated signal Angle-of-Arrival (AoA) at multiple anchors. An anchor is a base station of known position and equipped with a narrowband multi-antenna array. However, the design and implementation of indoor positioning systems based on AoA measurements involve multiple challenges. The first part of this thesis mainly addresses the impact of hardware impairments on the accuracy of AoA measurements. In practice, the subspace-based algorithms such as Multiple Signal Classification (MUSIC) suffer from sensitivity to array calibration errors coming from hardware imperfections. A detailed experimental implementation is performed using a Software Defined Radio (SDR) platform to precisely evaluate the accuracy of AoA measurements. For this purpose, a new Over-the-Air (OTA) calibration method is proposed and the array calibration error is investigated. The experimental results are compared with the theoretical analysis. These results show that array calibration errors can cause some degrees of uncertainty in AoA estimation. Moreover, we propose iterative positioning algorithms based on AoA measurements for low capacity IoT sensors with high accuracy and fair computational complexity. Efficient positioning accuracy is obtained by iterating between the angle and position estimation steps. We first develop a Data-Aided Maximum a Posteriori (DA- MAP) estimator based on the preamble of the transmitted signal. DA-MAP estimator relies on the knowledge of the transmitted signal which makes it impractical for narrowband communications where the preamble is short. For this reason, a Non-Data- Aided Maximum a Posteriori (NDA-MAP) estimator is developed to improve the AoA accuracy. The iterative positioning algorithms are therefore classified as Data-Aided Iterative (DA-It) and Non-Data-Aided Iterative (NDA-It) depending on the knowledge of the transmitted signal that is used for estimation. Both numerical and experimental analyses are carried out to evaluate the performance of the proposed algorithms. The results show that DA-MAP and NDA-MAP estimators are more accurate than MUSIC. The results also show that DA-It comes very close to the performance of the optimal approach that directly estimates the position based on the observation of the received signal, known as Direct Position Estimation (DPE). Furthermore, the NDA-It algorithm significantly outperforms the DA-It because it can use a much higher number of samples; however, it needs more iterations to converge. In addition, we evaluate the computational savings achieved by the iterative schemes compared to DPE through a detailed complexity analysis. Finally, we investigate the performance degradation of the proposed iterative algorithms due to the impact of multipath and NLOS propagation in indoor environments. Therefore, we develop an enhanced iterative positioning algorithm with an anchor selection method in order to identify and exclude NLOS anchors. The numerical results show that applying the anchor selection strategy significantly improves the positioning accuracy in indoor environments. / Doctorat en Sciences de l'ingénieur et technologie / info:eu-repo/semantics/nonPublished
|
8 |
The realization of signal processing methods and their hardware implementation over multi-carrier modulation using FPGA technology. Validation and implementation of multi-carrier modulation on FPGA, and signal processing of the channel estimation techniques and filter bank architectures for DWT using HDL coding for mobile and wireless applications.Migdadi, Hassan S.O. January 2015 (has links)
First part of this thesis presents the design, validation, and implementation of an Orthogonal
Frequency Division Multiplexing (OFDM) transmitter and receiver on a Cyclone II FPGA chip using DSP builder and Quartus II high level design tools. The resources in terms of logical elements (LE) including combinational functions and logic registers allocated by the model have been investigated and addressed. The result shows that implementing the basic OFDM transceiver allocates about 14% (equivalent to 6% at transmitter and 8% at receiver) of the available LE resources on an Altera Cyclone II EP2C35F672C6 FPGA chip, largely taken up by the FFT, IFFT and soft decision encoder.
Secondly, a new wavelet-based OFDM system based on FDPP-DA based channel estimation is proposed as a reliable ECG Patient Monitoring System, a Personal Wireless telemedicine application. The system performance for different wavelet mothers has been investigated. The effects of AWGN and multipath Rayleigh fading channels have also been studied in the analysis. The performances of FDPP-DA and HDPP-DA-based channel estimations are compared based on both DFT-based OFDM and wavelet-based OFDM systems. The system model was studied using MATLAB software in which the average BER was addressed for randomized data. The main error differences that reflect the quality of the received ECG signals between the reconstructed and original ECG signals are established.
Finally a DA-based architecture for 1-D iDWT/DWT based on an OFDM model is implemented for an ECG-PMS wireless telemedicine application. In the portable wireless body transmitter unit at the patient site, a fully Serial-DA-based scheme for iDWT is realized to support higher hardware utilization and lower power consumption; whereas a fully Parallel-DA-based scheme for DWT is applied at the base unit of the hospital site to support a higher throughput. It should be noted that the behavioural level of HDL models of the proposed system was developed and implemented to confirm its correctness in simulation. Then, after the simulation process the design models were synthesised and implemented for the target FPGA to confirm their validation.
|
Page generated in 0.0464 seconds