Cette thèse a été effectuée dans le cadre du projet européen FP7 EMPHATIC (Enhanced Multicarrier Techniques for Professional Ad-Hoc and Cell-Based Communications). Plusieurs universités européennes et deux partenaires industriels: THALES Communications Security et CASSIDIAN ont participé à ce projet. L'objectif de ce projet est de développer, d'évaluer et de démontrer les apports des techniques multi-porteuses avancées, permettant une meilleure utilisation des bandes de fréquences radio existantes en fournissant des services de données à large bande, en coexistence avec les services traditionnels à bande étroite. Le projet porte sur l'application de radiocommunications mobiles professionnelles (Professional Mobile Radio : PMR). L'idée principale de ce projet est d'analyser la viabilité des systèmes à large bande utilisant des bancs de filtres (Filter Bank Multi Carrier : FBMC) conjointement avec une modulation d'amplitude en quadrature avec décalage (Offset Quadrature Amplitude Modulation : OQAM) dans le cadre de la 5ème génération (5G) des systèmes radio-mobiles. La modulation FBMC-OQAM se positionne comme candidate potentielle pour les futurs systèmes de communication. Cette modulation avancée offre de nombreux avantages tels que l’excellente localisation fréquentielle de sa densité spectrale de puissance (DSP), une robustesse au bruit de phase, aux décalages de fréquence ainsi qu’à l’asynchronisme entre les utilisateurs. Ces atouts, la rendent plus attrayant qu’OFDM pour l’application PMR, la radio cognitive (CR) et la 5G. Cependant, comme toute autre technique de modulation muti-porteuses, FBMC-OQAM souffre d’un facteur de crête ou d’un PAPR (pour Peak to Average Power Ratio) élevé. Lorsque l'amplificateur de puissance (AP), utilisé au niveau de l’émetteur, est opéré proche de sa zone non-linéaire (NL), ce qui est le cas dans la pratique, la bonne localisation fréquentielle de la DSP du système FBMC/OQAM est sérieusement compromise, en raison des remontées spectrales. Le premier objectif de cette thèse est de prédire l'étendue des remontées spectrales dans les systèmes FBMC-OQAM, introduites par la non-linéarité AP. Le deuxième objectif de ce travail est de proposer des techniques, pour les systèmes FBMC-OQAM, permettant la réduction du PAPR et la linéarisation de l’AP, afin d'atténuer les effets NL. L’utilisation des cumulants, a permis de prédire les remontées spectrales pour les signaux FBMC-OQAM après amplification NL. En outre, certains algorithmes de réduction du PAPR, basées sur des approches probabilistes et des techniques d'ajout de signaux, ont été proposés. La capacité de coexistence du système à large bande utilisant FBMC-OQAM avec des systèmes PMR à bande étroite en présence de PA a été analysée et il a été démontré que la coexistence est possible, à condition qu'il y est une bonne combinaison entre le recul du signal à l’entrée de l’AP (Input Back-Off : IBO), la réduction du PAPR et la linéarisation de l’AP. Enfin, une nouvelle technique de linéarisation de l’AP a été proposée pour le système FBMC-OQAM. / This thesis is part of the European FP7 EMPHATIC project (Enhanced Multicarrier Techniques for Professional Ad-Hoc and Cell-Based Communications) including various European universities and two main industrial partners: THALES Communications Security and CASSIDIAN. The EMPHATIC objective is to develop, evaluate and demonstrate the capability of enhanced multi-carrier techniques to make better use of the existing radio frequency bands in providing broadband data services in coexistence with narrowband legacy services. The project addresses the Professional Mobile Radio (PMR) application. The main idea is to analyze the viability of broadband systems based on filter-bank multi-carrier (FBMC) clubbed with o ffset quadrature amplitude modulation (OQAM) in the context of the future 5th Generation (5G) radio access technology (RAT). Increasingly, the FBMC-OQAM systems are gaining appeal in the probe for advanced multi-carrier modulation (MCM) waveforms for future communication systems. This advanced modulation scheme o ers numerous advantages such as excellent frequency localization in its power spectral density (PSD), a robustness to phase noise, frequency off sets and also to the multi-user asynchronism; making it more appealing than OFDM for PMR, cognitive radio (CR) and 5G RAT. However, like any other MCM technique, FBMC-OQAM suff ers from high PAPR. When the power amplifi er (PA) non-linearity, which is realistic radio-frequency impairment, is taken into account; the good frequency localization property is severely compromised, due to the spectral regrowth. The first objective of this PhD thesis is, to predict the extent of the spectral regrowth in FBMC-OQAM systems, due to the PA non-linearity. The second objective is to probe techniques for FBMC-OQAM systems, such as PAPR reduction and PA linearization, in order to mitigate the NL eff ects of PA. By cumulant analysis, spectral regrowth prediction has been done for FBMC-OQAM systems. Also, some algorithms for PAPR reduction, which are based on probabilistic approach and adding signal methods, have been proposed. The coexistence capability of the FBMC-OQAM based broadband system with the narrowband PMR systems in the presence of PA has been analyzed and it has been found that coexistence is possible, provided there is a symbiotic combination of PA Input Back-off (IBO), PAPR reduction and PA linearization. Finally, a novel PA linearization technique has been proposed for FBMC-OQAM.

It is well known that communication systems employing multiple transmit and multiple receive antennas provide high data rates along with increased reliability. Some of the design criteria of the space-time block codes (STBCs) for multiple input multiple output (MIMO)communication system are that these codes should attain large transmit diversity, high data-rate, low decoding-complexity, low decoding –delay and low peak-to-average power ratio (PAPR). STBCs based on real orthogonal designs (RODs) and complex orthogonal designs (CODs) achieve full transmit diversity and in addition, these codes are single-symbol maximum-likelihood (ML) decodable. It has been observed that the data-rate (in number of information symbols per channel use) of the square CODs falls exponentially with increase in number of antennas and it has led to the construction of rectangular CODs with high rate. We have constructed a class of maximal-rate CODs for n transmit antennas with rate if n is even and if n is odd. The novelty of the above construction is that they 2n+1 are constructed from square CODs. Though these codes have a high rate, this is achieved at the expense of large decoding delay especially when the number of antennas is 5or more. Moreover the rate also converges to half as the number of transmit antennas increases. We give a construction of rate-1/2 CODs with a substantial reduction in decoding delay when compared with the maximal- rate codes. Though there is a significant improvement in the rate of the codes mentioned above when compared with square CODs for the same number of antennas, the decoding delay of these codes is still considerably high. For certain applications, it is desirable to construct codes which are balanced with respect to both rate and decoding delay. To this end, we have constructed high rate and low decoding-delay RODs and CODs from Cayley-Dickson Algebra. Apart from the rate and decoding delay of orthogonal designs, peak-to-average power ratio (PAPR) of STBC is very important from implementation point of view. The standard constructions of square complex orthogonal designs contain a large number of zeros in the matrix result in gin high PAPR. We have given a construction for square complex orthogonal designs with lesser number of zero entries than the known constructions. When a + 1 is a power of 2, we get codes with no zero entries. Further more, we get complex orthogonal designs with no zero entry for any power of 2 antennas by introducing co- ordinate interleaved variables in the design matrix. These codes have significant advantage over the existing codes in term of PAPR. The only sacrifice that is made in the construction of these codes is that the signaling complexity (of these codes) is marginally greater than the existing codes (with zero entries) for some of the entries in the matrix consist of co-ordinate interleaved variables. Also a class of maximal-rate CODs (For mathematical equations pl see the pdf file)

Actualment estem entrant a una nova era de la informació amb gran demanda de sistemes de comunicació sense fils. Nous serveis com dades i video requereixen transmissions fiables d'alta velocitat, fins i tot en escenaris d'alta mobilitat. A més a més, la dificultat d'assignar el limitat espectre radioelèctric juntament amb la necessitat d'incrementar el temps de vida de les bateries dels terminals mòbils, requereix el diseny de transceptors que usin la potència i l'ampla de banda disponibles de manera eficient. Les comunicacions multiportadora basades en OFDM són capaces de satisfer la majoria d'aquests requeriments. Però, entre altres reptes, reduir la sensibilitat a la amplificació no-lineal és un factor clau durant el diseny. En aquesta tesi doctoral s'analitza la sensibilitat dels sistemes multiportadora basats en OFDM a l'amplificació no-lineal i es consideren formes eficients per superar aquest problema. La tesi s'enfoca principalment al problema de reduir les fluctuacions de l'envolupant del senyal transmès. En aquest sentit es presenta també un estudi de les mètriques de l'envolupant del senyal, PAPR i CM. A més a més, basant-nos en l'anàlisis presentat es proposen noves tècniques per sistemes OFDM i MC-SS. Per MC-SS, també es tracta el diseny d'una tècnica de postprocessament en forma de detector multiusuari per canals no-lineals. / Actualmente estamos entrando en una nueva era de la información donde se da una gran demanda de sistemas de comunicación inalámbricos. Nuevos servicios como datos y vídeo requieren transmisiones fiables de alta velocidad, incluso en escenarios de alta movilidad. Además, la dificultad de asignar el limitado espectro radioeléctrico junto con la necesidad de incrementar el tiempo de vida de las baterías de los terminales móviles, requiere el diseño de transceptores que usen eficientemente la potencia y el ancho de banda disponibles. Las comunicaciones multiportadora basadas en OFDM son capaces de satisfacer la mayoría de dichos requerimientos. Sin embargo, entre otros retos, reducir su sensibilidad a la amplificación no-lineal es un factor clave durante el diseño. En esta tesis se analiza la sensibilidad de los sistemas multiportadora basados en OFDM a la amplificación no-lineal y se consideran formas eficientes para superar dicho problema. La tesis se enfoca principalmente al problema de reducir las fluctuaciones de la envolvente. En este sentido también se presenta un estudio de las métricas de la señal, PAPR y CM. Además, basándonos en el análisis presentado se proponen nuevas técnicas para OFDM y MC-SS. Para MC-SS, también se trata el diseño de un detector multiusuario para canales no-lineales. / We are now facing a new information age with high demand of wireless communication systems. New services such as data and video require achieving reliable high-speed transmissions even in high mobility scenarios. Moreover, the difficulty to allocate so many wireless communication systems in the limited frequency band in addition to the demand for long battery life requires designing spectrum and power efficient transceivers. Multicarrier communications based on OFDM are known to fulfill most of the requirements of such systems. However, among other challenges, reducing the sensitivity to nonlinear amplification has become a design key. In this thesis the sensitivity of OFDM-based multicarrier systems to nonlinear amplification is analyzed and efficient ways to overcome this problem are considered. The focus is mainly on the problem of reducing the envelope fluctuations. Therefore, a study of the signal metrics, namely PAPR and CM, is also presented. From the presented analysis, several new techniques for OFDM and MC-SS are proposed. For MC-SS, the design of a post-processing technique in the form of a multiuser detector for nonlinearly distorted MC-SS symbols is also addressed.

Many communications signal formats are not power efficient because of their large peak-to-average power ratios (PARs). Moreover, in the presence of nonlinear devices such as power amplifiers (PAs) or mixers, the non-constant-modulus signals may generate both in-band distortion and out-of-band interference. Backing off the signal to the linear region of the device further reduces the system power efficiency. To improve the power efficiency of the communication system, one can pursue two approaches: i) linearize the PA; ii) reduce the high PAR of the input signal. In this dissertation, we first explore the optimal nonlinearity under the peak power constraint. We show that the optimal nonlinearity is a soft limiter with a specific gain calculated based on the peak power limit, noise variance, and the probability density function of the input amplitude. The result is also extended to the fading channel case. Next, we focus on digital baseband predistortion linearization for power amplifiers with memory effects. We build a high-speed wireless test-bed and carry out digital baseband predistortion linearization experiments. To implement adaptive PA linearization in wireless handsets, we propose an adaptive digital predistortion linearization architecture that utilizes existing components of the wireless transceiver to fulfill the adaptive predistorter training functionality. We then investigate the topic of PAR reduction for OFDM signals and forward link CDMA signals. To reduce the PAR of the OFDM signal, we propose a dynamic selected mapping (DSLM) algorithm with a two-buffer structure to reduce the computational requirement of the SLM method without sacrificing the PAR reduction capability. To reduce the PAR of the forward link CDMA signal, we propose a new PAR reduction algorithm by introducing a relative offset between the in-phase branch and the quadrature branch of the transmission system.

Selected mapping (SLM) schemes are commonly employed to reduce the peak-to-average power ratio (PAPR) in orthogonal frequency division multiplexing (OFDM) systems. It has been shown that the computational complexity of the traditional SLM scheme can be substantially reduced by adopting conversion vectors obtained by using the inverse fast Fourier transform (IFFT) of the phase rotation vectors in place of the conventional IFFT operations. To ensure that the elements of these phase rotation vectors have an equal magnitude, conversion vectors should have the form of a perfect sequence. This study firstly presents three novel classes of perfect sequence, each of which comprises certain base vectors and their cyclically shifted versions. Three novel low-complexity SLM schemes are then proposed based upon the unique structures of these perfect sequences. It is shown that while the PAPR reduction performances of the proposed schemes are marginally poorer than that of the traditional SLM scheme, the three schemes achieve a substantially lower computational complexity. Since the three proposed PAPR reduction schemes cannot be utilized in the orthogonal frequency division multiple access (OFDMA) system. A low-complexity scheme for PAPR reduction in OFDMA uplink systems using either an interleaved or a sub-band sub-carrier assignment strategy is also proposed in the second part of this study. The proposed scheme requires just one IFFT operation. The PAPR reduction performance of the proposed scheme is only marginally poorer than that of the traditional SLM scheme. However, the proposed schemes have significantly lower computational complexities. Besides, multiple-input multiple-output (MIMO) OFDM systems with space-frequency block coding (SFBC) are well-known for their robust performance in time selective fading channels. However, SFBC MIMO-OFDM systems have a high computational complexity since the number of IFFTs required scales in direct proportion to the number of antennas at the transmitter. Furthermore, SFBC MIMO-OFDM systems have a high PAPR. Accordingly, a low-complexity PAPR reduction scheme for SFBC MIMO OFDM systems with the Alamouti encoding scheme is proposed in this study. Extending this scheme obtains two low-complexity transmitter architectures for SFBC MIMO-OFDM systems with a general encoding matrix and an arbitrary number of transmitter antennas. The proposed schemes achieve a significant reduction in computational complexity by fully exploiting the time-domain signal properties of the transmitted signal. In addition, a PAPR reduction scheme is presented based on the proposed transmitter schemes. It is shown that the PAPR reduction performance of the proposed scheme is almost as good as that of the traditional SLM scheme, but is achieved with a substantially lower computational complexity.

Multi-carrier systems based on orthogonal frequency division multiplexing (OFDM) are efficient technologies for the implementation of broadband wireless communication systems. OFDM is widely used and has been adopted for current mobile broadband wireless communication systems such as IEEE 802.a/g wireless LANs, WiMAX, 3GPP LTE, and DVB-T/H digital video broadcasting systems. Despite their many advantages, however, OFDM-based systems suffer from potentially high peak-to-average power ratio (PAR). Since communication systems typically include nonlinear devices such as RF power amplifiers (PA) and digital-to-analog converters (DAC), high PAR results in increased symbol error rates and spectral radiation. To mitigate these nonlinear effects and to avoid nonlinear saturation effects of the PA, the operating point of a signal with high peak power must be backed off into the linear region of the PA. This so-called output backoff (OBO) results in a reduced power conversion efficiency which limits the battery life for mobile applications, reduces the coverage range, and increases both the cost of the PA and power consumption in the cellular base station. With the increasing demand for high energy efficiency, low power consumption, and greenhouse gas emission reduction, PAR reduction is a key technique in the design of practical OFDM systems. Motivated by the PAR reduction problem associated with multi-carrier systems, such as OFDM, this research explores the state of the art of PAR reduction techniques and develops new signal processing techniques that can achieve a minimum PAR for given system parameters and that are compatible with the appropriate standards. The following are the three principal contributions of this dissertation research. First, we present and derive the semi-analytical results for the output of asymptotic iterative clipping and filtering. This work provides expressions and analytical techniques for estimating the attenuation factor, error vector magnitude, and bit-error-rate (BER), using a noise enhancement factor that is obtained by simulation. With these semi-analytical results, we obtain a relationship between the BER and the target clipping level for asymptotic iterative clipping and filtering. These results serve as a performance benchmark for designing PAR reduction techniques using iterative clipping and filtering in OFDM systems. Second, we analyze the impact of the selected mapping (SLM) technique on BER performance of OFDM systems in an additive white Gaussian noise channel in the presence of nonlinearity. We first derive a closed-form expression for the envelope power distribution in an OFDM system with SLM. Then, using this derived envelope power distribution, we investigate the BER performance and the total degradation (TD) of OFDM systems with SLM under the existence of nonlinearity. As a result, we obtain the TD-minimizing peak backoff (PBO) and clipping ratio as functions of the number of candidate signals in SLM. Third, we propose an adaptive clipping control algorithm and pilotaided algorithm to address a fundamental issue associated with two lowcomplexity PAR reduction techniques, namely, tone reservation (TR) and active constellation extension (ACE). Specifically, we discovered that the existing low-complexity algorithms have a low clipping ratio problem in that they can not achieve the minimum PAR when the target clipping level is set below the initially unknown optimum value. Using our proposed algorithms, we overcome this problem and demonstrate that additional PAR reduction is obtained for any low value of the initial target clipping ratio. / text

Along with the rapidly increasing demand for wireless data while more and more crowded radio frequency (RF) spectrum, optical wireless communications (OWC) become a promising candidate to complement conventional RF communications, especially for indoor short and medium range data transmissions. Orthogonal frequency division multiplexing (OFDM) is considered for OWC due to its ability to boost data rates. However, the average emitted optical power and dynamic range of driving signals of LEDs are two major constraints in OWC. OFDM waveforms exhibits high upper and lower peak-to-average power ratios (PAPRs), which make OFDM signals optical power inefficient and easy to violate the dynamic range of LEDs, resulting clipping and nonlinear distortions. In this dissertation, we analyze and design optical power and dynamic range constrained OWC systems, for which OFDM is our major subject. We first derive distributions of upper PAPR and lower PAPR of OWC-OFDM signals. Then we analyze the clipped OFDM signals in term of error vector magnitude (EVM), signal-to-distortion ratio (SDR), and achievable data rates under both optical power and dynamic range constraints. The next part of this dissertation is the OFDM system design for visible light communications (VLC) considering illumination requirement. We investigate the illumination-to-communication efficiency (ICE) in VLC-OFDM, and design the brightness control and flickering mitigation schemes for VLC-OFDM. In the end, to reduce the complexity of driving circuits of LEDs , we propose using delta-sigma modulators in VLC-OFDM systems to convert continuous magnitude OFDM symbols into two-level LED driver signals without loss of the communication theory advantages of OFDM.

Digital communication systems which use Orthogonal Frequency Division Multiplexing (OFDM) are now widely used and have many advantages. The main disadvantage is the requirement for highly linear analogue electronics including the high power amplifier (HPA). This requirement cannot be met in all circumstances because of the occurrence of symbols with high peak to average power ratio (PAPR). Such symbols may be non-linearly distorted by limiting. Approaches to solve this problem have been either to reduce the PAPR at the transmitter or to try to mitigate the effect of the non-linearity at the receiver. Soft-limiting, i.e. applying limiting in software prior to the HPA is a simple way to reduce the PAPR. It produces non-linear distortion which will cause an increase in the bit-error-rate (BER) at the receiver. This thesis surveys existing alternatives ways of reducing the effect of non-linearity and proposes some new ones. Two iterative receiver techniques, based on statistical analysis of the nature of the non-linearity, have been implemented and investigated. These are the ‘Bussgang Noise Cancellation’ (BNC) technique and the ‘Decision Aided Reconstruction’ (DAR) techniques. As these techniques are valid for any memory-less nonlinearity, an alternative form of limiting, named as Inverted-Wraparound (IWRAP) has been included in the BNC investigation. A new method is proposed which is capable of correcting the received time-domain samples that are clipped, once they have been identified. This is named the ‘Equation-Method’ and it works by identifying constellation symbols that are likely to be correct at the receiver. If there are a sufficient number of these and they are correctly identified, the FFT may be partitioned to produce a set of equations that may be solved for the clipped time-domain samples. The thesis proposes four enhancements to this new method which improve its effectiveness. It is shown that the best form of this method outperforms conventional techniques especially for severe clipping levels. The performance of these four enhancements is evaluated over channels with additive white Gaussian noise (AWGN) in addition to clipping distortion. A technique based on a ‘margin factor’ is designed to make these methods work more effectively in the presence of AWGN noise. A new combining algorithm referred as ‘HARQ for Clipping’ is presented where soft bit decisions are combined from multiple transmissions. ‘HARQ for Clipping’ has been combined with the best version of the Equation-Method, and the performance of this approach is evaluated in terms of the BER with different levels of AWGN. It has been compared to other approaches from the literature and was found to out-perform the BNC iterative receiver by 3dB at signal to noise ratios around 10dB. Without HARQ, the best version of the Equation-Method performs better than the BNC receiver, at signal-to-nose ratios above about 17dB.

This paper presents a new hybrid PAPR reduction technique for the OFDM signal, which combines a multiple symbol representations method with a signal clipping method. The clipping method is a nonlinear PAPR reduction scheme, where the amplitude of the signal is limited to a given threshold. Considering the fact that the signal must be interpolated before A/D conversion, a variety of clipping methods has been proposed. Some methods suggest the clipping before interpolation, having the disadvantage of the peaks re-growth. Other methods contributed that the clipping after interpolation, having the disadvantage of out-of-band power production. In order to overcome this problem different filtering techniques have been proposed. Filtering can also cause peak re-growth, but less than the clipping before interpolation. Another clipping technique supposes that only subcarriers having the highest phase difference between the original signal and its clipped variant will be changed. This is the case of the partial clipping method. To further reduce the PAPR, the dynamic of the clipped signal can be compressed. Linear methods like partial transmit sequence or selective mapping has been proposed for the reduction of PAPR as well. Another PAPR reduction method is the tone reservation. It uses tones on which no data is sent to reduce the transmitted signal peaks. Derivatives of this method with lower computation complexity and improved performance have been proposed: One-Tone One-Peak and one by-one iteration. A similar PAPR reduction method is the multiple symbol representations, where alternative signalling points are used to represent one symbol. The simulation results highlight the advantages of the proposed PAPR reduction method. / The proposed technique namely Adaptive Active Constellation Extension (Adaptive ACE) Algorithm reduced the high Peak-to-Average Power Ratio (PAPR) of the Orthogonal Frequency Division Multiplexing (OFDM) systems. The Peak-to-Average Power Ratio (PAPR) is equal to 6.8 dB for the target clipping ratios of 4 dB, 2 dB and 0 dB by using Adaptive Active Constellation Extension (Adaptive ACE) Algorithm. Thus, the minimum PAPR can be achieved for low target clipping ratios. The Signal-to-Noise Ratio (SNR) of the Orthogonal Frequency Division Multiplexing (OFDM) signal obtained by the Adaptive Active Constellation Extension (Adaptive ACE) algorithm is equal to 1.2 dB at a Bit Error Rate (BER) of 10-0..4 for different constellation orders like 4-Quadrature Amplitude Modulation (4-QAM), 16-Quadrature Amplitude Modulation (16-QAM) and 64-Quadrature Amplitude Modulation (16-QAM). Here, the Bit Error Rate of 10-0.4 or 0.398, that means a total of 398-bits are in error when 1000-bits are transmitted via a communication channel or approximately 4-bits are in error when 10-bits are transmitted via a communication channel, which is high when compared to that of the original Orthogonal Frequency Division Multiplexing (OFDM) signal. The other problems faced by the Adaptive Active Constellation Extension (Adaptive ACE) algorithm are Out-of-Band Interference (OBI) and peak regrowth. Here, the Out-of-Band Interference (OBI) is a form of noise or an unwanted signal, which is caused when the original Orthogonal Frequency Division Multiplexing (OFDM) signal is clipped for reducing the peak signals which are outside of the predetermined area and the peak regrowth is obtained after filtering the clipped signal. The peak regrowth results to, increase in the computational time and computational complexity. In this paper, we have proposed a PAPR reduction scheme to improve the bit error rate performance by applying companding transform technique. Hence, 1-1.5 dB reduction in PAPR with this Non-companding technique is achieved. In Future, We can accept to implement the same on Rician and Rayleigh channels. / Clement Ranjith Anthikkad (E-mail: clement.ranjith@gmail.com / clan11@bth.se) & Irfan Ahmed Baig (E-mail: baig.irfanahmed@gmail.com / ir-a11@bth.se )

Massive MIMO (multiple-input–multiple-output) is a multi-antenna technology for cellular wireless communication, where the base station uses a large number of individually controllable antennas to multiplex users spatially.  This technology can provide a high spectral efficiency.  One of its main challenges is the immense hardware complexity and cost of all the radio chains in the base station.  To make massive MIMO commercially viable, inexpensive, low-complexity hardware with low linearity has to be used, which inherently leads to more signal distortion.  This thesis investigates how the degenerated linearity of some of the main components—power amplifiers, analog-to-digital converters (ADCs) and low-noise amplifiers—affects the performance of the system, with respect to data rate, power consumption and out-of-band radiation. The main results are: Spatial processing can reduce PAR (peak-to-average ratio) of the transmit signals in the downlink to as low as 0B; this, however, does not necessarily reduce power consumption.  In environments with isotropic fading, one-bit ADCs lead to a reduction in effective signal-to-interference-and-noise ratio (SINR) of 4dB in the uplink and four-bit ADCs give a performance close to that of an unquantized system.  An analytical expression for the radiation pattern of the distortion from nonlinear power amplifiers is derived.  It shows how the distortion is beamformed to some extent, that its gain never is greater than that of the desired signal, and that the gain of the distortion is reduced with a higher number of served users and a higher number of channel taps.  Nonlinear low-noise amplifiers give rise to distortion that partly combines coherently and limits the possible SINR.  It is concluded that spatial processing with a large number of antennas reduces the impact of hardware distortion in most cases.  As long as proper attention is paid to the few sources of coherent distortion, the hardware complexity can be reduced in massive MIMO base stations to overcome the hardware challenge and make massive MIMO commercial reality. / Massiv MIMO (eng: multiple-input–multiple-output) är en flerantennsteknologi för cellulär trådlös kommunikation, där basstationen använder ett stort antal individuellt styrbara antenner för att multiplexa användare i rummet.  Denna teknologi kan tillhandahålla en hög spektral effektivitet.  En av dess främsta utmaningar är den enorma hårdvarukomplexiteten och kostnaden hos basstationens alla radiokedjor.  För att massiv MIMO skall bli kommersiellt attraktivt, måste billiga, enkla hårdvarukomponenter med låg linjäritet användas, vilket oundvikligen leder till mer signaldistorsion.  Denna avhandling undersöker hur den försämrade linjäriteten hos några av huvudkomponenterna – effektförstärkare, analog-digital-omvandlare (AD-omvandlare) och lågbrusförstärkare – påverkar systemets prestanda, i termer av datatakt, effektförbrukning och utombandsstrålning.  Huvudresultaten är: Rumslig signalbehandling kan reducera sändsignalernas toppvärde i nerlänken ända ner till 0dB, vilket dock inte nödvändigtvis minskar effektförbrukningen.  I miljöer med isotrop fädning leder enbits-AD-omvandlare till 4dB lägre signal-till-interferens-och-brus-förhållande i upplänken, och fyrabits-AD-omvandlare ger en prestanda nära den ett system utan kvantisering kan uppnå.  Ett analytiskt uttryck för strålningsmönstret för distorsionen från icke-linjära effektförstärkare härleds.  Det visar hur distorsionen till viss del lobformas, att dess förstärkning aldrig är starkare än förstärkningen för den önskade signalen och att distorsionens förstärkning minskar med ett högre antal betjänade användare och ett högre antal kanaltappar.  Icke-linjära lågbrusförstärkare ger upphov distorsion som delvis kombinerar koherent och begränsar det möjliga signal-till-brus-och-interferens-förhållandet.  Slutsatsen är att rumslig signalbehandling med ett stort antal antenner reducerar hårdvarudistorsionens inverkan i de flesta fall.  Så länge som de få källorna till koherent distorsion ges tillbörlig uppmärksamhet, kan hårdvarukomplexiteten minskas i basstationer för massiv MIMO för att övervinna hårdvaruutmaningen och göra massiv MIMO kommersiell verklighet. / 蜂窩無線通訊領域中的大規模多天線技術以多個單獨可控的天線通過空間複用的方式服務多個用戶。如是可以大幅提高頻譜效率。實現此技術的主要難題在於基站所用射頻單元的極大複雜度及成本。爲使大規模多天線技術適用在商業系統中，需使用導致失真的低複雜度低成本的非線性硬件。本文探討若將一些主要部件——功放、模數轉換器、低噪聲放大器——的線性程度降低，系統性能是如何受到影響的，即系統的速率、功耗、帶外泄露等指標。主要的結果爲：空間信號處理可以降低下行信號的峯均比，直至０分貝；然而低峯均比不一定能夠降低功耗。用一比特模數轉換器使上行的信干噪比減少４分貝；用四比特模數轉換器可在各向同性衰落的環境裏實現接近無量化系統的性能。本文推導出非線性功放失真輻射方向的解析公式。該公式展示失真在某種程度上會被波束成形的；具體而言，失真的波束成形增益不大於有效信號的增益，波束成形增益會根據服務用戶數量和信道階數的增長而降低。非線性低噪聲放大器引起的失真，一部分會相干地合併，因此會限制信干噪比的增長。結論爲多天線的空間信號處理可以減少硬件失真的影響。只要適當地處理少數相干失真的來源，大規模多天線基站可以降低硬件複雜度，解決硬件難題，使大規模多天線技術成功地應用在商業系統中成爲現實。