The subject of the diploma thesis is accumulation tanks in heating systems. The first part introduces the topic of thermal energy storage and types of accumulation tanks. The second part describes two specific options of heating the building of the boarding house and the restaurant with the use of storage tanks in the heating system. A gas condensing boiler is designed as a heat source in one variant and a pellet boiler in the other variant. The third part deals with experimental measurements, in which the accumulation tank with the installation for better stratification of hot water and the accumulation tank without the installation are compared.

Articular cartilage is an avascular and flexible connective tissue found in joints. It produces a cushioning effect at the joints and provides low friction to protect the ends of the bones from wear and tear/damage. It has poor repair capacity and any injury can result pain and loss of mobility. One of the common forms of articular cartilage disease which has a huge impact on patient¿s life is arthritis. Research on cartilage cell/tissue engineering will help patients to improve their physical activity by replacing or treating the diseased/damaged cartilage tissue. Cartilage cell, called chondrocyte is embedded in the matrix (Lacunae) and has round shape in vivo. The in vitro monolayer culture of primary chondrocyte causes morphological change characterized as dedifferentiation. Transforming growth factor-beta (TGF-¿), a cytokine superfamily, regulates cell function, including differentiation and proliferation. The effect of TGF-¿1, 2, 3, and their manipulated forms in biological regulation of primary chondrocyte was investigated in this work. A novel method was developed to isolate and purify the primary chondrocytes from knee joint of neonate Sprague-Dawley rat, and the effect of some supplementations such as hyaluronic acid and antibiotics were also investigated to provide the most appropriate condition for in vitro culture of chondrocyte cells. Addition of 0.1mg/ml hyaluronic acid in chondrocyte culture media resulted an increase in primary chondrocyte proliferation and helped the cells to maintain chondrocytic morphology. TGF-¿1, 2 and 3 caused chondrocytes to obtain fibroblastic phenotype, alongside an increase in apoptosis. The healing process of the wound closure assay of chondrocyte monolayers were slowed down by all three isoforms of TGF-¿. All three types of TGF-¿ negatively affected the strength of chondrocyte adhesion. TGF-¿1, 2 and 3 up regulated the expression of collagen type-II, but decreased synthesis of collagen type-I, Chondroitin sulfate glycoprotein, and laminin. They did not show any significant change in production of S-100 protein and fibronectin. TGF-¿2, and 3 did not change expression of integrin-¿1 (CD29), but TGF-¿1 decreased the secretion of this adhesion protein. Manipulated TGF-¿ showed huge impact on formation of fibroblast like morphology of chondrocytes with chondrocytic phenotype. These isoforms also decreased the expression of laminin, chondroitin sulfate glycoprotein, and collagen type-I, but they increased production of collagen type-II and did not induce synthesis of fibronectin and S-100 protein. In addition, the strength of cell adhesion on solid surface was reduced by manipulated TGF-¿. Only manipulated form of TGF-¿1 and 2 could increase the proliferation rate. Manipulation of TGF-¿ did not up regulate the expression of integrin-¿1in planar culture system. The implications of this R&D work are that the manipulation of TGF-¿ by combination of TGF-¿1, 2, and 3 can be utilized in production of superficial zone of cartilage and perichondrium. The collagen, fibronectin and hyaluronic acid could be recruited for the fabrication of a biodegradable scaffold that promotes chondrocyte growth for autologous chondrocyte implantation or for formation of cartilage.

Ce travail porte sur l’étude et le développement d’un système innovant de ventilation et de chauffage au bois dans les habitations à basse consommation d’énergie, qui sont appelées à devenir la référence constructive en France dès 2015. Dans ces habitations fortement isolées et particulièrement étanches à l’air, les besoins de chauffage sont très faibles et peuvent être couverts par une source de chaleur d’origine renouvelable, telle que le bois énergie. En outre, l’utilisation d’une ventilation performante s’impose comme étant un critère essentiel pour assurer la bonne qualité de l’air intérieur et peut même devenir l’unique vecteur de chauffage en apportant l’appoint de chaleur sur l’air insufflé dans les différentes pièces de l’habitation. Le système présenté dans cette étude propose ainsi de combiner les avantages d’un appareil de chauffage au bois de petite puissance, ici un poêle à granulés de bois, et ceux d’une ventilation à récupération de chaleur sur l’air extrait, grâce à un conduit échangeur intégré à la cheminée du poêle et relié au réseau de soufflage de la ventilation. Développé en partenariat avec l’industriel POUJOULAT, spécialisé dans la fabrication de conduits de cheminée métalliques, ce conduit échangeur permet de récupérer sur l’air neuf une partie de la chaleur initialement perdue par les fumées et de la distribuer dans toutes des zones de vie de l’habitation, même les plus éloignées de l’appareil au bois. Après avoir défini la configuration de couplage à adopter pour assurer le bon fonctionnement de l’ensemble et garantir à la fois la sécurité et le confort des occupants, les performances de plusieurs prototypes de conduit échangeur sont caractérisées expérimentalement. Les résultats obtenus lors des essais en laboratoire permettent alors d’orienter l’évolution des prochains prototypes et de souligner la nécessité de travailler avec un poêle à granulés de bois dont le cycle de combustion est étanche. Un modèle mathématique est également développé pour prédire les performances du dernier prototype de conduit échangeur à triple paroi non isolé sur sa surface extérieure et sa validation est obtenue suite au bon accord entre les résultats calculés et ceux mesurés lors des essais. L’ensemble du système combiné est ensuite installé dans deux habitations à basse consommation d’énergie situées près de Poitiers. L’exploitation des températures et des consommations recueillies pendant la première saison de chauffe montre la bonne tenue du système combiné, ses limites, ainsi que ses conditions d’appropriation par les occupants, dont le comportement apparaît jouer un rôle prédominant dans la réduction des consommations énergétiques. / This work is devoted to the study and development of an innovative wood-based air-heating system for energy-efficient dwellings, which are expected to become the building reference in France from 2015 onwards. As these kinds of homes are highly insulated and particularly airtight, heating requirements are very low and may be covered by a renewable energy source, such as wood energy. In addition, efficient ventilation is absolutely required to ensure indoor air quality and may even sometimes be use as the only way to provide heat into the various rooms of the house. In this context, the system presented in this study aims to combine advantages of a low power wood-burning appliance, as a wood-pellet stove, and those of a mechanical ventilation heat-recovery unit, thanks to a heat exchanger integrated into the chimney of the pellet stove and connected to the ventilation air supply network. Developed in partnership with POUJOULAT, a metallic chimneys manufacturer, this new heat exchanger recovers a part of the heat from flue gases and enables to warm up the fresh air distributed in each living zone of the house, even the most remote of the wood heating device. After defining the best coupling configuration to ensure the proper behaviour of the system, as well as both safety and comfort of the occupants, performances of several heat exchanger prototypes are characterized experimentally. The results from tests in laboratory are then used to guide prototypes development and they highlight the need to work with a room-sealed wood-pellet stove. Moreover, a mathematical model is developed to predict the performances of the latest prototype of triple concentric tube heat exchanger with no insulation at the outer surface. Then, the model validation is obtained following the good agreement between calculated results and those measured during the laboratory tests. The combined system is then installed in two energy-efficient dwellings near Poitiers. Operating temperatures and energy consumptions collected during the first heating season show the good reliability of the combined system, its limitations and its conditions of acceptance by the occupants, whose behaviour is pointed out as a major factor in reducing energy consumptions.

L’extrapolation des réacteurs catalytiques nécessite l’acquisition des données cinétiques sur des réacteurs à petite échelle dans les conditions opératoires industrielles. Le critère de dimensionnement utilisé lors de la réduction d’échelle est la conservation de la vitesse volumique horaire, ce qui conduit à des vitesses de circulation très faibles dans les réacteurs pilotes à lit-fixe. A ces vitesses, les flux de transfert de matière externes peuvent devenir limitant par rapport au flux de réaction. Dans ce contexte, une nouvelle géométrie de réacteur a été imaginée pour intensifier les transferts de matière et chaleur et pour augmenter les vitesses de circulation des fluides : le réacteur "filaire". Il s’agit d’un réacteur dont le diamètre est égal ou proche de celui des grains de catalyseur et avec un ratio longueur sur diamètre très élevé. Le principal objectif de cette thèse est de caractériser ce réacteur en termes d’hydrodynamique et de transferts de matière externes pour définir ses limites d’utilisation. En écoulement diphasique, ce réacteur est relativement piston et la rétention liquide est élevée, ce qui permet d'assurer un mouillage total du catalyseur. En ce qui concerne les vitesses des transferts de matière externe, celles-ci sont proches de celles d'un réacteur agité avec panier et sont supérieures à celles caractéristiques d'un réacteur pilote à lit-fixe conventionnel. Cette observation est liée à l’augmentation des vitesses locales du liquide et à la présence d'un écoulement du type Taylor modifié. En conclusion, le réacteur "filaire" constitue une alternative efficace aux réacteurs pilotes à lit-fixe pour l’étude de catalyseurs mis en forme. / Small size fixed-bed reactors are a common choice for testing industrial supported catalyst under industrial operating conditions. The most common criterion for reactor’s scale-down is based on the conservation of the liquid hourly space velocity which leads to a very low fluid flow velocity at the laboratory scale. Under these conditions, the external mass transfer flux can become the limiting step of the process. In this context, a new reactor geometry was proposed to intensify mass and heat transfers and to increase fluid flow velocities: the single pellet string reactor. This reactor is composed of a tube with an internal diameter close to that of the catalyst particles and with a high length over diameter ratio. The main goal of this thesis is to characterise the hydrodynamic and external mass transfer performances of this new reactor in order to define its application domain. In two-phase gas-liquid flow, the reactor flow is plug flow and the liquid hold-up values are high, which insures a complete wetting of the catalyst particles. The mass transfer coefficients were quantified and the measured rates are much higher than those observed in conventional pilot fixed-bed reactors, which can be explained by the increased local liquid velocities and by the modified Taylor flow regime. Catalytic tests with a very fast model reaction revealed that the external mass transfer performances of the single pellet string reactor are close to those measured in a stirred tank reactor equipped with a catalytic basket. In conclusion, the single pellet string reactor represents a new and efficient alternative to fixed-bed pilot reactors to study shaped catalysts.

<p>Denna avhandling behandlar rökgasutsläpp av persistenta organiska föroreningar, framförallt dioxiner, vid förbränning av fasta biobränslen och torrt hushållsavfall i relativt små anläggningar (5-600 kW) utan avancerad rökgasreningsteknik.</p><p>Samförbränning av avfall och biobränsle i effektiva mindre biobränslepannor testades som en alternativ strategi till den vanligen förekommande storskaliga hanteringen och förbränningen fast hushållsavfall. Medan storskalig förbränning av avfall ger investeringsmässiga fördelar med rökgasreningsteknik etc. kan små lokala anläggningar ha transportmässiga fördelar och möjligheter till utnyttjande av lokala biobränsletillgångar. Källsorterat, torrt, brännbart hushållsavfall insamlades från hushåll i glesbygd och samförbrändes i brikettform med energigräset rörflen i 150-600 kW biobränslepannor. Endast undantagsvis understeg dioxinemissionerna gällande gränsvärden för avfallsförbränning och nivåerna av väteklorid i rökgas översteg gränsvärdena flerfaldigt. Det bedömdes att någon form av extra rökgasrening är nödvändig för att säkerställa nivågränserna. Dioxiner hittades också i det eldade avfallet, framförallt i textilfraktionen. Dioxinmängderna i rökgaserna var oftast lägre än i det ingående bränslet.</p><p>Intermittent pelletseldning gav oväntat höga utsläpp av dioxiner med en emissionsfaktor på 28 ng(WHO-TEQ)/kg. Vedeldning i en modern miljömärkt villapanna gav betydligt lägre utsläpp av dioxiner än eldning i en gammal kombipanna och eldning med full lufttillförsel, som kan jämföras med användning av ackumulatortank, resulterade i upp till 90% minskning av utsläpp av dioxiner jämfört med eldning med reducerat lufttillskott (’pyreldning’). Eldning av plastavfall i en vedpanna gav höga utsläpp av dioxiner.</p><p>Okontrollerad förbränning av trädgårdsavfall och hushålls avfall i tunna eller som öppen eld ’bakgårdsbränning’, gav stora variationer i utsläppsnivåer som bara delvis kunde kopplas till avfallsinnehåll. Resultaten visar att denna typ av förbränning kan vara en betydande källa till dioxiner i miljön, och ett emissionsfaktorintervall på 4-72 ng (WHO-TEQ)/kg föreslås för bedömningar av utsläpp från backgårdsbränning av avfall med låga eller måttliga klorhalter.</p><p>En sammanfattande slutsats av alla försök är att dioxin utsläpp beror på komplicerade samband mellan bränsleinnehåll och förbränningsbetingelser. Bränslen med mycket höga klorhalter av ger oftast högre utsläpp av dioxiner än bränslen med låga klorhalter medan små skillnader döljs av variationer i förbränningsbetingelser.</p> / <p>This thesis deals with emissions of persistent organic pollutants, primarily dioxins, from the combustion of solid biofuels and dry combustible household waste in relatively small facilities, 5-600 kW, without advanced air pollution controls.</p><p>Co-combustion of waste and biofuel in effective small boilers was tested as an alternative to prevailing large-scale management and combustion strategies for handling municipal solid waste. This approach includes no advanced air pollution control systems, but offers two advantages: limiting transport and providing scope to use local biofuel resources. Source-sorted, dry, combustible household waste was collected from households in a sparsely populated area and co-combusted as briquettes together with reed canary-grass in 150-600 kW biofuel boilers. Most trials showed difficulties to meet regulative limits for the emissions of dioxins valid for incineration of MSW and the regulated limits for emissions of hydrochloric acid were exceeded manifold. It was concluded that additional flue-gas cleaning will be needed to ensure that emissions are sufficiently low. Dioxins were also found in the waste, especially in the textile fraction. The mass of dioxins in the flue-gas emissions was generally lower than the mass in the fuel input.</p><p>Intermittent combustion of wood pellets in a residential boiler resulted in an unexpectedly high dioxin emissions factor of 28 ng (WHO-TEQ)/kg fuel. Combustion of wood in a modern environmentally certified boiler yielded considerably lower dioxin emissions than combustion in an old boiler, and combustion with a full air supply, i.e. with use of heat storage tank, resulted in up to 90% reductions in dioxin emission factors compared to combustion with reduced air supply. Combustion of plastic waste in a residential wood boiler resulted in high emissions of dioxins.</p><p>Tests of uncontrolled combustion of garden and household waste in barrels or open fires, ‘backyard burnings’, resulted in emissions with large variations that could only be partly correlated to the waste constituents. The results imply that this may be an important source of dioxins in the environment and an emission factor range of 4-72 ng (WHO-TEQ)/kg is suggested for estimating emissions from backyard burnings of lightly and moderately chlorine-contaminated waste.</p><p>A summarized conclusion from all of the experiments is that predicting emission levels from waste contents is not straightforward (except that fuels with very high chlorine levels will usually result in high levels of dioxins in flue-gas emissions). Moderate differences in chlorine levels will usually be masked by the effect of variations in combustion conditions.</p>

To investigate the roles of different dorsal spinal pathways in controlling movements in rats, I performed lesions of specific spinal pathways and measured the behaviour abilities of rats using different sensorimotor behavioural tests. The first experiment was designed to understand the contribution of sensory pathways traveling in the dorsal funiculus during locomotion and skilled movements using sensitive behavioural tests. I demonstrated that ascending sensory fibers play an important role during overground locomotion and contribute to skilled forelimb movements. The second experiment compared the differences in sensorimotor abilities caused by dorsal funicular lesions performed at two different levels of rat spinal cord. My results showed that the pathways present in the cervical and thoracic dorsal funiculus exert different functional effects over control of limb movement during locomotion. The third experiment investigated the compensatory potential of dorsal funicular pathways after dorsolateral funicular injuries in rats. My results showed that dorsal funicular pathways do not compensate for loss of dorsolateral pathways during the execution of locomotor tasks, though there is indirect evidence that rats with dorsolateral funicular lesions might rely more on ascending sensory pathways in the dorsolateral funiculus during skilled forelimb movements. Finally, the fourth experiment was designed to investigate the compensation from dorsolateral funicular pathways after injuries to pyramidal tract in rats. I demonstrated that pathways running in the spinal dorsolateral funiculus do provide compensatory input to spinal circuitry to maintain skilled reaching abilities after lesions of the pyramidal tract but these same pathways do not appear to compensate during either overground locomotion or skilled locomotion. Thus, this compensatory response is task-specific. These results highlight the fact that behavioural context determines the nature of compensation from spared pathways after spinal cord injuries.

To investigate the roles of different dorsal spinal pathways in controlling movements in rats, I performed lesions of specific spinal pathways and measured the behaviour abilities of rats using different sensorimotor behavioural tests. The first experiment was designed to understand the contribution of sensory pathways traveling in the dorsal funiculus during locomotion and skilled movements using sensitive behavioural tests. I demonstrated that ascending sensory fibers play an important role during overground locomotion and contribute to skilled forelimb movements. The second experiment compared the differences in sensorimotor abilities caused by dorsal funicular lesions performed at two different levels of rat spinal cord. My results showed that the pathways present in the cervical and thoracic dorsal funiculus exert different functional effects over control of limb movement during locomotion. The third experiment investigated the compensatory potential of dorsal funicular pathways after dorsolateral funicular injuries in rats. My results showed that dorsal funicular pathways do not compensate for loss of dorsolateral pathways during the execution of locomotor tasks, though there is indirect evidence that rats with dorsolateral funicular lesions might rely more on ascending sensory pathways in the dorsolateral funiculus during skilled forelimb movements. Finally, the fourth experiment was designed to investigate the compensation from dorsolateral funicular pathways after injuries to pyramidal tract in rats. I demonstrated that pathways running in the spinal dorsolateral funiculus do provide compensatory input to spinal circuitry to maintain skilled reaching abilities after lesions of the pyramidal tract but these same pathways do not appear to compensate during either overground locomotion or skilled locomotion. Thus, this compensatory response is task-specific. These results highlight the fact that behavioural context determines the nature of compensation from spared pathways after spinal cord injuries.

Heroin use and dependency is a growing concern within South Africa, individuals face difficulty in remaining abstinent from the use of heroin due to constant relapse. The opioid antagonist known as the naltrexone pellet implant offers an alternative form of aid to relapse prevention in the recovery and abstinence from heroin dependency. This qualitative study explored the subjective experiences and perceptions of heroin dependent individuals, that made use of the naltrexone pellet implant. This study was rooted in the interpretive, qualitative paradigm where a phenomenological research design was used. Participants were selected using a purposive, snowball sampling technique and four individuals who had made use of the naltrexone pellet implant for the aid in heroin dependency for a minimum of three-months were interviewed. Interpretative Phenomenological Analysis (IPA) was used to extract recurrent themes across participants. The findings suggested that the use of the naltrexone pellet implant was beneficial in the aid for relapse prevention from heroin use. Furthermore, the exploration of difficulties that were faced in remaining abstinent, the attempt to make use of the naltrexone pellet implant and the physical and psychological aspects regarding the use of this alternative method of remaining abstinent were explored in this study. / Psychology / M.A. (Psychology (Research Consultation))

Denna avhandling behandlar rökgasutsläpp av persistenta organiska föroreningar, framförallt dioxiner, vid förbränning av fasta biobränslen och torrt hushållsavfall i relativt små anläggningar (5-600 kW) utan avancerad rökgasreningsteknik. Samförbränning av avfall och biobränsle i effektiva mindre biobränslepannor testades som en alternativ strategi till den vanligen förekommande storskaliga hanteringen och förbränningen fast hushållsavfall. Medan storskalig förbränning av avfall ger investeringsmässiga fördelar med rökgasreningsteknik etc. kan små lokala anläggningar ha transportmässiga fördelar och möjligheter till utnyttjande av lokala biobränsletillgångar. Källsorterat, torrt, brännbart hushållsavfall insamlades från hushåll i glesbygd och samförbrändes i brikettform med energigräset rörflen i 150-600 kW biobränslepannor. Endast undantagsvis understeg dioxinemissionerna gällande gränsvärden för avfallsförbränning och nivåerna av väteklorid i rökgas översteg gränsvärdena flerfaldigt. Det bedömdes att någon form av extra rökgasrening är nödvändig för att säkerställa nivågränserna. Dioxiner hittades också i det eldade avfallet, framförallt i textilfraktionen. Dioxinmängderna i rökgaserna var oftast lägre än i det ingående bränslet. Intermittent pelletseldning gav oväntat höga utsläpp av dioxiner med en emissionsfaktor på 28 ng(WHO-TEQ)/kg. Vedeldning i en modern miljömärkt villapanna gav betydligt lägre utsläpp av dioxiner än eldning i en gammal kombipanna och eldning med full lufttillförsel, som kan jämföras med användning av ackumulatortank, resulterade i upp till 90% minskning av utsläpp av dioxiner jämfört med eldning med reducerat lufttillskott (’pyreldning’). Eldning av plastavfall i en vedpanna gav höga utsläpp av dioxiner. Okontrollerad förbränning av trädgårdsavfall och hushålls avfall i tunna eller som öppen eld ’bakgårdsbränning’, gav stora variationer i utsläppsnivåer som bara delvis kunde kopplas till avfallsinnehåll. Resultaten visar att denna typ av förbränning kan vara en betydande källa till dioxiner i miljön, och ett emissionsfaktorintervall på 4-72 ng (WHO-TEQ)/kg föreslås för bedömningar av utsläpp från backgårdsbränning av avfall med låga eller måttliga klorhalter. En sammanfattande slutsats av alla försök är att dioxin utsläpp beror på komplicerade samband mellan bränsleinnehåll och förbränningsbetingelser. Bränslen med mycket höga klorhalter av ger oftast högre utsläpp av dioxiner än bränslen med låga klorhalter medan små skillnader döljs av variationer i förbränningsbetingelser. / This thesis deals with emissions of persistent organic pollutants, primarily dioxins, from the combustion of solid biofuels and dry combustible household waste in relatively small facilities, 5-600 kW, without advanced air pollution controls. Co-combustion of waste and biofuel in effective small boilers was tested as an alternative to prevailing large-scale management and combustion strategies for handling municipal solid waste. This approach includes no advanced air pollution control systems, but offers two advantages: limiting transport and providing scope to use local biofuel resources. Source-sorted, dry, combustible household waste was collected from households in a sparsely populated area and co-combusted as briquettes together with reed canary-grass in 150-600 kW biofuel boilers. Most trials showed difficulties to meet regulative limits for the emissions of dioxins valid for incineration of MSW and the regulated limits for emissions of hydrochloric acid were exceeded manifold. It was concluded that additional flue-gas cleaning will be needed to ensure that emissions are sufficiently low. Dioxins were also found in the waste, especially in the textile fraction. The mass of dioxins in the flue-gas emissions was generally lower than the mass in the fuel input. Intermittent combustion of wood pellets in a residential boiler resulted in an unexpectedly high dioxin emissions factor of 28 ng (WHO-TEQ)/kg fuel. Combustion of wood in a modern environmentally certified boiler yielded considerably lower dioxin emissions than combustion in an old boiler, and combustion with a full air supply, i.e. with use of heat storage tank, resulted in up to 90% reductions in dioxin emission factors compared to combustion with reduced air supply. Combustion of plastic waste in a residential wood boiler resulted in high emissions of dioxins. Tests of uncontrolled combustion of garden and household waste in barrels or open fires, ‘backyard burnings’, resulted in emissions with large variations that could only be partly correlated to the waste constituents. The results imply that this may be an important source of dioxins in the environment and an emission factor range of 4-72 ng (WHO-TEQ)/kg is suggested for estimating emissions from backyard burnings of lightly and moderately chlorine-contaminated waste. A summarized conclusion from all of the experiments is that predicting emission levels from waste contents is not straightforward (except that fuels with very high chlorine levels will usually result in high levels of dioxins in flue-gas emissions). Moderate differences in chlorine levels will usually be masked by the effect of variations in combustion conditions.

The diploma thesis is divided into three parts. The first part is theoretical devoted to the introduction of BETONG building material. And next It is also devoted to themes of low - energy buildings and nearly zero-energy buildings, heat sharing and thermal comfort. In the second part is the concept of the heating system elaborated in three variants of the design in the scope of the study for the new family house. The third part is devoted to use of shell blocks of the BETONG with internal contact insulation compared to other masonry systems.