This diploma thesis deals with the study of resistance of ETICS surface treatments to biotic attack. The theoretical part elaborates a research focused on biotic attack of facades of buildings insulated by contact insulation systems ETICS. Based on the information obtained during the elaboration of the bachelor thesis and further study, the optimization methodology of ETICS surface treatment resistance to biotic attack proposed in 2018 is elaborated. In the practical part, the proposed methodology is verified, evaluated and recommendations concerning the suitability of using the proposed methodology in construction practice are implemented.

The diploma thesis deals with the deposition of layers of 2-ethyl-2-oxazoline monomer in a dielectric barrier discharge in a nitrogen atmosphere. The theoretical part describes polyoxazolines, dielectric barrier discharge, plasma polymerization and diagnostic methods that describe the characteristics of the prepared layers. The experimental part deals with the deposition of layers and the determination of physicochemical properties. Finally, the results are compared with layers that were made of 2-methyl-2-oxazoline.

This thesis deals with study of surface layers of low-carbon steels formed by chemical-heat treatment. The first three chapters consist of theoretical part of the thesis, there are explained basic physical principles of these technologies and described individual types, the third chapter deals with the application of chemical-heat treated low-carbon steels in mechanical engineering. The experimental part of thesis deals with analysis of surface layers of two low-carbon steels formed using plasma nitrocarburizing and gas nitrocarburizing. The properties of these layers are evaluated based on the results of mechanical tests (hardness tests) and observation of microstructure. The thesis is completed by discussion, where the achieved results are evaluated.

Magnetické nanočástice a nanostrukturované materiály jsou velkým příslibem v mnoha oblastech, včetně biomedicíny, sanace životního prostředí nebo získávání energie. Proto neustále roste zájem o výzkum jejich jedinečných vlastností a vývoj uskutečnitelných výrobních postupů. Tato práce se zabývá metodou samouspořádávání, spočívající v povrchové precipitaci tenkých vrstev, za účelem výroby epitaxních polí nanoostrůvků ze slitiny FeRh na různých monokrystalických substrátech. Při tomto výrobním postupu zůstává zachována metamagnetická fázová přeměna nanoostrůvků. Morfologie a magnetické vlastnosti samouspořádaných nanomagnetů z FeRh jsou charakterizovány kombinací experimentálních technik a modelování, přičemž bylo zjištěno, že jejich rovnovážné tvary a magnetické uspořádání jsou navzájem propojeny. Kromě toho je navržena cesta pro získání volných nanočástic, která by mohla potenciálně umožnit využití metamagnetických nanostruktur v buněčných kulturách a biomedicíně obecně. Za tímto účelem jsou nanoostrůvky FeRh uvolňovány ze substrátu chemickým leptáním. Chování nanočástic a jejich reakce na teplotu a magnetické pole jsou studovány v kapalném prostředí. Metamagnetické vlastnosti separovaných nanočástic jsou charakterizovány pomocí vibrační magnetometrie.

Perfluoroalkylated substencies are priority organics polutants. They are evolved to the environment from many sources. We classify them as new xenobiotics which are present in the environment. There will be described their chemical, physical and environmental properties in theoretical part and there will be described the analytical chemistry of these substancies in varios types of environmental samples. There will be developed metod for their identification and quantification. For this assignment will be use especially chromathografic methods. There will be developed standard operation procedure. The procedure will be verify on real environmental samples.

Diploma thesis is focused on the choose of methods and optimalisation analysis procedure of selected pharmaceuticals (salicylic acid, ibuprofene, naproxene, ketoprofene and diclofenac) in surface and waste water by using gas chromatography with mass spectrometer (GC-MS). Solid-phase extraction (SPE) with Oasis HLB cartridges was used as an extraction method in this analysis. Extraction is followed by derivatization and their optimalization of selected pharmaceuticals. Derivatization and its optimalization were performed by two silylation reagens N-methyl-N-(trimethylsilyl)trifluoroacetamide (MSTFA) and N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA). Different volumes of derivatization reagents, different temperatures and different times were used during the procedure. The best combination is then used for analysis of real samples. Real samples of waste water were collected in sewage treatment plants in Brno – Modřice and real samples of surface water were collected from several rivers and one pond in region Moravia. This thesis also presents and tests SPE methods for extraction and concentration selected sulfonamide residues (sulfamethazine, sulfamethoxazole, sulfapyridine and sulfathiazole) from the aquatic environment.

Thin film deposition, characterization and properties of self-assembled monolayers based on silicon were studied with emphasis on the SA monolayers deposited from vinyltriethoxysilane and vinyltrichlorsilane. The thesis is aimed at basic properties of the SA monolayer and explanation of its growth. Methods and techniques used for analysis of the monolayer were described as well. Contact angle measurements and an evaluation of the surface free energy are depicted in details. The deposited SA layers were observed with respect to their chemical composition and surface morphology by X-ray photoelectron spectroscopy (XPS), ellipsometry and atomic force microscopy (AFM).

The diploma thesis studies composite of PP and filler particle. As a particle filler was used commercially available CaCO3 (SOCAL 31). The submitted thesis had a goal to find new approaches and technologies of filler surface treatment in order to improve properties of composite materials. The plasma discharge behind static pressure was used for the surface treatment of the fillers. These fillers were afterwards analyzed by using of sedimentation analysis, turbidimetry, infra-red spectroscopy (FT-IR), X-ray diffraction analysis (XRD), scan electron microscopy (SEM), transmission electron microscopy and particle size distribution by laser diffraction. The composites with various volume parts of the fillers were prepared in PIB and studied by short-time tests. Furthermore, the influence of an adhesive layer on fracture mechanical properties of prepared composite was study. Regarding to experimental demand, there was not possible to realize long-term mechanical properties.

The purpose of the thesis was to study chemical and corrosion resistance of selected conversion coatings. The corrosion and the possibilities of corrosion protection with focus on conversion coatings on aluminum and steel surface were described in the theoretical part. In the experimental part corrosion and chemical resistance of samples without the next treatment and samples with polyester powder coating and synthetic coating were tested.

The diploma thesis deals with study of system of polypropylene and inorganic filler. As filler was used commercially available particulate filler CaCO3 termed NPCC 201. The objective of the study was a surface plasma treatment of filler in order to obtain composite based on polypropylene. Mechanical properties of this composite will show significantly greater value than basic matrix. The filler was treated in dielectric barrier plasma discharge by atmospheric pressure. The characterization of filler was performed before and after plasma treatment by x-ray photoelectron spectroscopy (XPS), electron microscope (SEM) and sedimentation analysis. The distribution of particle size was measured by laser diffraction and by dynamic light scattering. The composite materials with various weight concentration of filler were prepared in POLYMER INSTITUTE BRNO by using the twin-screw extruder and the test specimens were prepared by the injection molding technology. Their mechanical properties was studied by using of short and long-term tests. The uniaxial creep testing in tension was used for study of long-term behavior of composites.