Good bond strength between overlay and substrate is a key factor in performance of concrete repairs. This thesis was aimed at studying the evaluation of bond strength between repair material and substrate at the interface. Many factors such as surface roughness, existence of micro cracks, compaction, curing etc influence the bond strength. The quality assurance of the bond strength requires test methods that can quantify the bond strength as well as identify the failure mode. There have been numerous investigations led to development of different test methods. The forces which are applied in each test and the failure mode are important in order to choose the proper test. An interpretive study on test methods is presented. While this study can provide individually useful information on bond strength and bond characterization, it also contains discussions about each test and comparison of test methods.

Performance of asphalt mixtures depends on the properties of its constituent materials, mixture volumetrics, and external factors such as load and environment. An important material property that influences the performance of an asphalt mixture is the surface free energy of the asphalt binder and the aggregate. Surface free energy, which is a thermodynamic material property, is directly related to the adhesive bond energy between the asphalt binder and the aggregate as well as the cohesive bond energy of the asphalt binder. This thermodynamic material property has been successfully used to select asphalt binders and aggregates that have the necessary compatibility to form strong bonds and resist fracture. Surface free energy, being based on thermodynamics, assumes the asphalt binder is a brittle elastic material. In reality, the asphalt binder is not brittle and dissipates energy during loading and unloading. The total work of fracture is the culmination of all energy inputted into the sample to create two new surfaces of unit area and is dependent on the test geometry and testing conditions (e.g., temperature, loading rate, specimen size, etc.). The magnitude of the bond energy (either adhesive or cohesive) can be much smaller in magnitude when compared to the total work of fracture measured using mechanical tests (i.e., peel test, pull-off test, etc.). Despite the large difference in magnitude, there exists evidence in the literature supporting the use of the bond energy to characterize the resistance of composite systems to cohesive and/or adhesive failures. If the bond energy is to be recognized as a useful screening tool by the paving industry, the relationship between the bond energy and total work of fracture needs to be understood and verified. The effect of different types of modifications (addition of polymers, addition of anti-strip agents, and aging) on the surface free energy components of various asphalt binders was explored in order to understand how changes in the surface free energy components are related to the performance of the asphalt mixtures. After the asphalt binder-aggregate combination was explored, the next step was to study how the surface free energy of water was affected by contact with the asphalt binder-aggregate interface. Aggregates, which have a pH of greater than seven, will cause the pH of water that contacts them to increase. A change in the pH of the contacting water could indicate a change in its overall surface free energy, which might subsequently increase or decrease the water's moisture damage potential. With surface free energy fully explored, the total work of fracture was measured using pull-off tests for asphalt binder-aggregate combinations with known surface free energy components. In order to fully explore the relationship between bond energy and total work of fracture, temperature, loading rate, specimen geometry, and moisture content were varied in the experiments. The results of this work found that modifications made to the asphalt binder can have significant positive or negative effects on its surface free energy components and bond energy. Moreover, the results from the pull-off tests demonstrated that a relationship exists between bond energy (from surface free energy) and total work of fracture (from pull-off tests), and that surface free energy can be used to estimate the performance of asphalt binder-aggregate combinations.

La faible densité et les propriétés mécaniques remarquables des composites polymères en font des matériaux de choix pour remplacer les métaux. Cependant, leurs propriétés physicochimiques rendent leurs surfaces peu adhésives pour divers types de revêtements. Pour améliorer l’adhérence de revêtements métalliques sur des substrats de PEEK, et pour mieux comprendre les mécanismes de l’adhésion, les propriétés de surface du matériau ont été modifiées par des procédés physiques en voie sèche.D’une part, cette étude montre que les traitements par plasma oxydants (à basse pression, ou à pression atmosphérique) permettent d’améliorer la mouillabilité de la surface et l’adhérence de revêtements métalliques, par l’augmentation de la polarité de la surface, quantifiée par XPS. D’autre part, cette étude montre que l’ablation laser infrarouge à impulsion femtoseconde permet la gravure d’un motif dense, induisant de meilleures tenues mécaniques de l’assemblage. Enfin, cette étude montre que la modification de la chimie et de la topographie combinées améliore davantage ce potentiel d’adhérence.Le but de cette étude est d’ouvrir une voie vers un modèle décrivant les mécanismes de l’adhésion, influencés par la chimie de surface et la géométrie d’un motif, en s’appuyant sur un modèle mécanique permettant de décrire la dynamique des contraintes se propageant au travers de l’interface, en tenant compte des propriétés mécaniques des matériaux. / Thanks to their low densities and good mechanical properties, polymer composites are good candidates for metal alloys substitutes. However, their physicochemical properties limit their adhesion potential towards several types of coatings. In order to improve metallic thin films adhesion on PEEK substrates, and to better comprehend adhesion mechanisms, dry-phase methods have been used to alter the surface properties of the material.First, this study shows that oxidative plasma treatments (at low or at atmospheric pressure) improve the wettability and the practical adhesion of metallic coatings, by an increase of the polar component of the surface, as measured by XPS. Second, this study shows that dense patterns etched by an infrared femtosecond laser allow good practical adhesion of the metallic thin films on the substrate. Finally, this study shows that the modification of both surface chemistry and the surface topography at the same time further improves the practical adhesion of the metallic thin films.The goal of this study is to propose a route towards a model describing the combined influence of surface texture and chemistry, with the support of a mechanical model describing the dynamics of the stress dissipation through the interface while taking into account the mechanicals properties of the interfacial materials.

La production d’énergie avec des cellules photovoltaïques organiques (OPV) est une des applications les plus prometteuses des semi-conducteurs organiques, en raison de leur compatibilité avec les substrats flexibles permettant des produits légers, peu chers et décoratifs. Pendant longtemps, poly(3-hexylthiophène) (P3HT) a été le polymère de choix dans l’OPV combiné au [6,6]-phényl-C61-butanoate de méthyle (PC61BM) comme accepteur. Toutefois, des recherches récentes ont porté sur des polymères avec meilleures absorption et processabilité, qui peuvent assurer des rendements et des durées de vie plus élevés. Des rendements de conversion en puissance (PCE) au-dessus de 11% ont récemment été démontrés. Cette thèse rapporte sur la synthèse et la caractérisation de deux séries de polymères dits à faible bande interdite, LBGs "push-pull" (ou donneur-accepteur), constitués de l'unité donneuse 4,4-bis(2-ethylhexyl)-5,5'-dithieno[3,2-b:2',3'-d]silole (DTS) combinée au 3,6-dithiophén-2-yl-2,5-dihydro-pyrrolo[3,4-c]pyrrole-1,4-dione (DPP) ou au 5,7-di(thiényl)thiéno[3,4-b]pyrazines (DTP), comme unité acceptrice. Toutes les molécules et les polymères ont été caractérisés chimiquement et leur propriétés optoelectroniques, morphologiques et photovoltaïques ont été determinées. La série DTS-DPP a été choisie parce qu'elle est représentative d'un grand nombre de polymères LBG et a fourni un modèle facilement accessible pour évaluer l'importance de la chaîne latérale utilisée sur leur propriétés optoélectroniques et thermiques. Les premières études sur les dispositifs à base de DTS-DPP:PC61BM ont été menées, pour déterminer les propriétés photovoltaïques. Le meilleur dispositif permet d’obtenir un PCE de 1,7% avec JSC de 5,9 mA cm-2, VOC de 0,54 V et FF de 0,58. La série DTS-DTP a été choisie pour la stabilité chimique élevée des deux unités et pour la facilité de substitution des groupes latéraux. La polymérisation a partiellement abouti, en donnant seulement des oligomères. La caractérisation chimique a pu être effectuée, mais leur application dans l’OPV n'a pas été explorée. En termes de stabilité, les mécanismes de défaillance électrique des dispositifs OPV ont été étudiés, montrant une méconnaissance de leur stabilité mécanique. Les contraintes caractéristiques de chaque couche mince présentes dans les cellules solaires organiques constituent la force motrice à l’origine de la délamination des interfaces faibles ou même leur decohésion, causant une perte de l'intégrité et des performances du dispositif. Une technique pour sonder les couches ou les interfaces fragiles dans les cellules solaires polymère:fullerene est présentée. Elle a été développée par l'établissement d'un nouveau set-up pour le test pull-off, développé en utilisant un dispositif à géométrie inverse, de structure verre/ITO/ZnO/P3HT:PC61BM/PEDOT:PSS/Ag. Les dispositifs délaminés ont montré que le point le plus faible est localisé à l'interface AL/HTL, en bon accord avec la littérature. La technique a été étendue en variant les deux couches sensibles, en utilisant differents polymères LBG pour l’AL (PSBTBT et PDTSTzTz) en combinaison avec deux formulations de PEDOT:PSS, CleviosTM HTL Solar à base d'eau et un nouveau HTL Solar 2 à base de solvant organique. Une différence entre la contrainte à la rupture des dispositifs avec différentes combinaisons de AL et HTL est visible, suggérant différents chemins de fracture, tel que confirmé par la caractérisation de surface et qui pourrait être corrélée avec la différence de comportement de la couche active avec les deux formulations de PEDOT:PSS. Une autre voie adoptée, a été d’introduire une couche d’interface de copolymère à blocs amphiphile afin d'améliorer la compatibilité des deux couches. Cette stratégie n'a pas abouti et la nouvelle architecture présente une adhésion réduite. La poursuite de l’amélioration des procédés de fabrication de ces dispositifs pourrait faire de cette nouvelle architecture, une alternative viable. / Organic photovoltaic (OPV) devices are one of the most promising applications of organic semiconductors due to their compatibility with flexible plastic substrates resulting in light weight, inexpensive and decorative products. For a long time poly(3-hexylthiophene) (P3HT) has been the polymer of choice in OPV devices in combination with [6,6]-phenyl-C61-butyric acid methylester (PC61BM) as acceptor. However, recent research has focused on polymers with improved absorbance and processability that can ensure higher efficiencies and longer lifetimes (Low BandGap polymers (LBGs)). This has been fully demonstrated with a power conversion efficiency (PCE) above 11%. This thesis reports synthesis and characterization of two series of so-called “push-pull” (or donor-acceptor) LBGs based on the donor unit 4,4′-bis(2-ethylhexyl)-5,5’-dithieno[3,2-b:2′,3′-d]silole (DTS) and either 3,6-dithiophen-2-yl-2, 5-dihydropyrrolo[3,4-c]pyrrole-1,4-dione (DPP) or 5,7-di(thienyl)thieno[3,4-b]pyrazines (DTP), as acceptor unit. All π-conjugated molecules and polymers were characterized by chemical investigation and their optoelectronic, morphological, and photovoltaic properties are reported. The DTS-DPP series was chosen because representative of a large number of LBG polymers and provided an easily accessible and useful template to discover the importance of the type of side-chain used on the polymer optoelectronic and thermal properties. First studies on DTS-DPP:PC61BM devices have been conducted, in order to investigate any effect on their photovoltaic properties. The best device obtained had a PCE of 1.7% with JSC of 5.9 mA•cm-2, VOC of 0.54 V and FF of 0.58. The DTS-DTP series was chosen for the high stability of the two units and for the ease of substitution of the side-groups. The synthesis was partially successful and only oligomers were obtained. Nonetheless, chemical characterization was performed but their application in OPV was not explored. In terms of device stability, the electrical failure mechanisms in OPV devices have been investigated, while little is known about their mechanical stability. The characteristic thin film stresses of each layer present in organic solar cells, in combination with other possible fabrication, handling and operational stresses, provide the mechanical driving force for delamination of weak interfaces or even their de-cohesion, leading to a loss of device integrity and performance. A technique to probe weak layers or interfaces in inverted polymer:fullerene solar cells is presented. It was developed by establishing a new set-up for the pull-off test. The technique was developed using inverted device, with the structure glass/ITO/ZnO/P3HT:PC61BM/PEDOT:PSS/Ag. The delaminated devices showed that the weakest point was localized at the active layer/hole transporting layer interface, in good agreement with the literature. The technique was extended varying both sensitive layers, using different p-type low bandgap (co)polymers for the active layer (PSBTBT and PDTSTzTz) in combination with two different PEDOT:PSS formulations, the water based CleviosTM HTL Solar and a new organic solvent based HTL Solar 2. The half-devices produced upon destructive testing have been characterized by contact angle measurement, AFM and XPS to locate the fracture point. A difference in the stress at break for devices made with different combinations of active and hole transporting layers is visible, suggesting different fracture paths, as confirmed by surface characterization and could be correlated to the different behavior of the active layer with the two PEDOT:PSS formulations. Another solution adopted, it had been the introduction of amphiphilic block-copolymer interlayer to enhance the compatibility of the two layers. This strategy was not successful and the new architecture showed reduced adhesion strength. Further development of device processing could make this new architecture a viable alternative.