The understanding of what properties the fibre should have in order to give the right end-product paper properties, along with the type of processing, is a subject for a lot of research and development. Today the ability to measure fibre properties on-line is widely used for pulps. It is often necessary to measure many properties and variables in a process. The data collected is therefore almost always multivariate. It is very hard to analyse process data due to a lot of noises. Correlations between fibre and paper properties are hard to find, but this does not mean that correlations do not exist. Fibre properties, measured by the pulp analyser PulpEye, were investigated and correlations to paper properties were studied. The work was divided into three different studies. Study 1 was an investigation of historical process data, in study 2 pulp samples from the production was analysed and study 3 was a refiner setting trial, were different refiner segments, flows through refiners and intensities were studied. Both the group-plots and MVDA’s based on the historical process data in study 1, showed that the Scott Bond was increased with increased amount of kinks and curl for the unbleached pine pulp (softwood pulp). Coarseness measurements, made in the study of historical data, indicated that the coarseness was varying in such a large extent that it was believable that it had effects in the papermaking process. Another interesting fibre property, investigated in the refiner setting trial, was crill. The amount of crill is said to have strong correlation to paper strength. The analysis showed that the incoming pulp had different amount of crill and that the amount of crill after the refiners also was varying for the different samples. The development of crill at different kappa numbers and for pulps refined with different segments and refiner strategies should be further investigated. In this work it has been difficult to find correlations between fibre properties and paper properties in the refiner setting trial. This could have been due to small variations of the different parameters. This work showed that the normal production can be handled very well and variations are rather small. It can be seen though, that problems do appear when parameters are deviating from the normal case. An efficient way to work is to do measurements when the incoming pulp parameters are deviating. It should also be more investigated how the most common deviating pulp parameters should be handled in the refining process and at the board machine. The communication between the pulp production and the board machines is recommended to be further developed, especially when the pulp production have disturbances that can be affecting the refining and further the board production.

The purpose of this bachelor thesis was to investigate how charged groups within the pulp fibre affect the beatability and the strength of the papers. To obtain different levels of charges on the pulp it was carboxymethylated. The different pulp samples were beaten to different degrees to investigate how charges interact with the beating. A PFI-mill was used for the beating because of the relatively homogenous effect on the fibres and the low demand for pulp fibres for each beating. The influence of the amount of charged groups on the surface and bulk swelling, as a result of the beating process, was evaluated.   The fibres were then analysed in a Fibre tester and using a microscope to see what had happened to the fibre structure.  The results showed that the PFI-mill mainly affects the surface of the fibres. The beatability, defined as the swelling obtain for a specific energy input, was greatly increased by the introduction of charges. It was also shown that there is a possibility to replace some of the energy input in the mill with the introduction of charges to obtain the same swelling and strength.   Paper sheets were formed from the different samples and some mechanical properties were analyzed. It was shown that the strength was initially improved by the introduction of charges but the improvement was partially lost during the beating. At the highest rate of beating the difference in strength between the samples had disappeared. This can be explained by the fact that the fibres, from the sample with highest number of charges, were destroyed. Microscopic images showed that the fibre was delaminated and at some sites there were extreme balloon-like swellings / Syftet med detta examensarbete var att undersöka hur laddade grupper hos massafibrer påverkar malbarheten och styrkan hos de papper som tillverkats av dessa fibrer. För att skapa olika laddningsnivåer karboxymetylerades viss del av massan för att introducera laddade grupper, två delar av ursprungsmassan karboxymetylerades och en del användes som referensmassa.  De olika massaproverna maldes i olika nivåer för att undersöka hur laddningarna och malningen interagerade. En PFI-kvarn användes för att mala fibrerna då det endast krävs små mängder fibrer och denna typ av kvarn påverkar fibrerna relativt homogent. Fibrerna analyserades sedan i en Fibre tester och med ett mikroskop för att se vad som hade hänt med fiberstrukturen. Resultaten visade att en PFI-kvarn till största delen påverkar fibrernas yta.  Malbarheten, som definierades som den svällning som åstadkoms vid en viss energiinsats i form av malvarv i kvarnen, ökades markant då ytterligare laddningar fanns närvarande i fibrerna. Det visades också att det går att ersätta en del av malningen med introduktion av laddningar till fibrerna för att uppnå samma svällning och styrka. Pappersark tillverkades därefter av de olika massatyperna och några mekaniska egenskaper testades. Det visades att styrkan ökades initialt av introduktionen av laddningar men denna förbättring minskade vid malningen. Vid den högsta malgraden hade skillnaden mellan de olika massorna försvunnit. Det kan förklaras av att fibrerna, från den massatyp med mest laddningar, hade förstörts. På vissa ställen hade fibern helt delaminerats och extrema ballonglika svällningar fanns.

No description available.

No description available.

Transformers are electrical devices used in practice to increase or decrease voltages. Transformers are of various sizes and used mainly in power distribution. To provide cooling and insulation, transformer oils are used together with cellulose that acts as a solid insulation. The most common type of transformer oil is mineral oil and is a product derived from the refining of crude oil. Its low cost and good compatibility with cellulose are two factors that have led to its predominant position as the common transformer oil. There are also synthetic ester based transformer oils, and following an increased interest in environmentally friendly products, transformer oils made from natural esters such as sunflower, soybean and rapeseed. Mineral oil is not biodegradable and is deemed as hazardous waste. The ester based oils are biodegradable and promoted as a more environmentally friendly alternative to mineral oil. In this thesis, the possibility of re-refining used mineral transformer oil is assessed from a financial perspective in the form of a business case and an LCA study has been done to compare the environmental impacts between ester based transformer oils and mineral based transformer oil. The results from the LCA study showed that from a cradle-to-gate perspective, mineral oil has a lower environmental impact than ester-based transformer oils. The re-refining of used mineral transformer oil further reduces the environmental impact. The results from the business case showed that a small scale re-refining facility is financially feasible but highly dependent on the supply and demand of used transformer oil. It is recommended to pursue further studies before making any decision. There is lack of data regarding the re-refining market in Eastern Europe and the accuracy of the LCA study can be further improved by having emissions data from re-refining used mineral transformer oil. / Transformatorer är elektriska komponenter som tillämpas vid spänningsregleringar. Dessa transformatorer har olika storlekar och används i eldistribution. Transformatorolja tillsammans med cellulosa används som elektrisk isolering och kylning av transformatorer. Den vanligaste typen av transformatorolja är mineralolja och är en produkt som erhålls vid raffinering av råolja. Dess låga kostnad och goda kompatibilitet med cellulosa är två faktorer som har lett till dess dominerande ställning. Det finns också syntetisk esterbaserad transformatorolja och efter ett ökat intresse för miljövänliga produkter så tillverkas även transformatoroljor av naturliga estrar så som solros, soja och raps. Mineralolja är inte nedbrytbar och anses vara farligt avfall. De esterbaserade oljorna är nedbrytbara och anses vara ett mer miljövänligt alternativ till mineralolja. I denna rapport utvärderades möjligheten till att återraffinera använd mineralolja ur ett ekonomiskt perspektiv i form av en affärsplan och en LCA-studie där esterbaserad olja och mineralolja har jämförts ur ett miljöperspektiv. Resultaten från LCA-studien visade att mineralolja från ett ”cradle-to-gate” perspektiv har en lägre miljöpåverkan än esterbaserade transformatoroljor. Återraffinering av använd mineralolja minskar dess miljöpåverkan ytterligare. Resultatet från affärsplanen visade att en småskalig återraffineringsanläggning är ekonomiskt hållbar men samtidigt väldigt beroende av utbud respektive efterfrågan på använd mineralolja. Det rekommenderas att göra en djupare analys innan man fattar ett beslut. Det finns brist på information med avseende på återraffineringsmarknaden i Östeuropa. Noggrannheten på LCA-studien kan förbättras ytterligare genom att emissionsdata från en återraffineringsanläggning är tillgänglig.

No description available.

Note:

Fibers are interesting materials alternative to replace conventional fossil-based plastics, as they are bio-based and do not lead to CO2 emissions. Due to their limited ductility, it is difficult to use them to make complex three-dimensional shapes. This problem has already been addressed in previous research studies but the processing conditions used here were never tried before. In this thesis, the incorporation of low molecular plasticizers onto the fibers is investigated to obtain a more ductile fiber-based material. More precisely, Paper and Fiber Research Institute (PFI) refining is used to mechanically treat the fibers and help the sorption of glycerol, urea, polyethyleneglycol (PEG), or polyvinylalcohol (PVA), followed by the formation of sheets from the modified pulp. However, it has been found that only small amounts of plasticizers were retained by this process. The refining itself on the fibers without additives enhanced fibrillation and developed mechanical bonding between the fibers, which resulted in increased strength and ductility. Also, the hot pressed (HP) drying technique was found to yield denser and stronger papers, compared to the non-pressed (HP) drying technique. As a comparison, the incorporation of plasticizers through ultrasonication and its effect on the paper properties were also considered from a previous study within the same research group. It has been found that this mechanical treatment retains more plasticizers than refining but yields different paper properties (especially an increased ductility). All these results suggest that PFI refining should be studied more in-depth by performing at least one process optimization cycle where less dilution takes place. / Fibrer är ett intressant, alternativt material att ersätta konventionella, fossila plaster. Men deras begränsade plasticitet gör det svårt att forma mer avancerade tredimensionella former. Detta problem har man adresserat i tidigare forskning, men bearbetningsförhållandena utvärderade i denna studie har inte testats tidigare. I denna uppsats studeras integrering av små molekylära mjukgörare in i fibrer för att framställa ett mer plastiskt, fiber-baserat material. Mer precist, Papirforskninginstituts (PFI) bearbetning används för att mekaniskt bearbeta fibrerna och underlätta sorption av glycerol, urea, Polyethylenglykol (PEG) och Polyvinylalkohol (PVA) följt av arkning av den bearbeta pappersmassan. Det har visats att i denna process bibehålls endast små mängder av mjukgörare på fibrerna. Dock har den mekaniska bearbetning i säg effekt på fibrerna, då den leder till defibrillering, och förstärker interaktionerna mellan fibrerna vilket leder till ett starkare och segare material. Utöver det, visar studien att värmepressningen (HP) som torktekning ger ett mer homogent resultat gällande arkens kvalitet. Som jämförelse användes en tidigare studie av samma forskargrupp som använt ultraljudsbehandling som medel att inkorporera mjukgörare och hur den behandlingen påverkade arken. Den behandlingen leder till högre retention av mjukgörare vilket leder till andra pappersegenskaper, speciellt högre duktilitet. Dessa studier visar att PFI bearbetningen behöver studeras i mer detalj för att se om det är en lämplig bearbetningsmetod och därför bör minst en till cykel med optimeringar göras för att se om högre halt mjukgörare kan bibehållas.

No description available.

No description available.