Lors d’un recuit inter-critique d’un acier dit « Medium Manganèse », dont la teneur en Mn est située entre 4 et 12 %, avec une microstructure initiale complètement martensitique, la formation de l’austénite obéit à un mécanisme spécifique qui porte le nom d'ART - « Austenite Reverted Transformation » (transformation inverse de l’austénite). L’objectif de ce travail de thèse était d’étudier et de modéliser les évolutions microstructurales en lien avec les propriétés mécaniques lors d’un recuit ART. Il a été déterminé que la microstructure finale se compose de phases de nature (ferrite, austénite résiduelle et martensite de trempe) et morphologie (en forme d’aiguille et polygonale) différentes. Une attention particulière a été accordée aux cinétiques de dissolution des carbures et de formation de l’austénite. Une vision complète de ces processus a été construite. En outre, le mécanisme de stabilisation de l’austénite résiduelle à la température ambiante a été étudié et discuté. Enfin, des essais de traction ont été réalisés afin d’évaluer le comportement mécanique de l’acier après différents recuits ART et établir le lien avec la microstructure. Une analyse plus détaillée du comportement de chaque constituant de la microstructure a été effectuée. A l'issue de cette thèse, un modèle complet est disponible pour calculer les courbes de contrainte vraie - déformation vraie d’un acier Medium Mn / During the intercritical annealing of fully martensitic Medium Mn steel, containing from 4 to 12 wt.% Mn, the formation of austenite happens through the so-called “Austenite Reverted Transformation” (ART) mechanism. In this PhD work, the evolution of both microstructure and tensile properties was studied as a function of holding time in the intercritical domain. The microstructure evolution was studied using a double experimental and modeling approach. The final microstructure contained phases of different natures (ferrite (annealed martensite), retained austenite and fresh martensite) and of different morphologies (lath-like and polygonal). A particular attention was paid to the kinetics of austenite formation in connection with cementite dissolution and to the morphology of the phases. A mechanism was proposed to describe the formation of such microstructure. The critical factors controlling thermal austenite stability, including both chemical and size effects, were determined and discussed, based on the analysis of the retained austenite time-evolution. At last, tensile properties of the steel were measured as a function of holding time and the relation between microstructure and mechanical behavior was analyzed. Advanced analysis of the individual behavior of the three major constituents was performed. As a final output of this work, a complete model for predicting the true-stress versus true-strain curves of medium Mn steels was proposed

The use of pre-hardened mold steels has increased appreciably over the years; more than 80% of the plastic mold steels are used in pre-hardened condition. These steels are delivered to the customer in finished state i.e. there is no need of any post treatment. With hardness around ~40HRC, they have properties such as good polishability, good weldability, corrosion resistance and thermal conductivity. Machinability is a very important parameter in pre-hardened mold steels as it has a direct impact on the cost of the mold. In normal machining operations involving intricate or near net shapes, machining constitutes around 60% of the total mold cost. Efforts are underway to explore every possible way to reduce costs associated with machining and to make production more economical. All the possible parameters which are considered to affect the machinability are being investigated by the researchers. This thesis work focuses on the effect of prior austenite grain size on the machinability of pre-hardened mold steel (Uddeholm Nimax).  Austenitizing temperatures and holding times were varied to obtain varying grain sized microstructures in different samples of the same material. As it was difficult to delineate prior-austenite grain boundaries, experimental and empirical methods were employed to obtain reference values. These different grain sized samples were thereafter subjected to machining tests, using two sets of cutting parameters. Maximum flank wear depth=0.2mm was defined for one series of test which were more akin to rough machining, and machining length of 43200mm or maximum wear depth=0.2mm were defined for second series of tests which were similar to finishing machining. The results were obtained after careful quantative and qualitative analysis of cutting tools. The results obtained for Uddeholm Nimax seemed to indicate that larger grain sized material was easier to machine. However, factors such as retained austenite content and work hardening on machined surface, which lead to degradation of machining operations were also taken into consideration. Uddeholm Nimax showed better machinability in large grained samples as retained austenite(less than 2%) content was minimal in the large grained sample. Small grained sample in Uddeholm Nimax had a higher retained austenite (7+2%) which resulted in degradation of machining operation and a lesser cutting tool life.

This project explores the feasibility of the solid-state welding method direct-drive friction welding to be used as a joining method for the nitrogen alloyed steel Uddeholm Vanax SuperClean, produced via processes based on powder metallurgy. Vanax SuperClean cannot be welded using fusion welding methods where the base material melts, due to nitrogen escaping the material, resulting in inferior quality welds. The cost of the material motivates the use of Vanax SuperClean for critical parts in applications, combined with a less costly material for the remaining parts, causing alternative joining methods to be examined. Vanax SuperClean is friction welded to itself and to Uddeholm steel types Stavax ESR and UHB 11. Samples are prepared for a number of examinations. Microstructures of the samples are examined using microscopy, microhardness testing is carried out per the Vickers principle, retained austenite is measured using X-ray diffraction and tensile testing of the welded samples is performed. Defect-free welds are produced in all examined samples, showing that the method is suitable for Vanax SuperClean and that no preheating or slow cooling of workpieces are necessary. The possibility of using friction stir welding as a joining method for Vanax SuperClean is discussed. / Detta projekt undersöker möjligheten att använda trycksvetsningsmetoden friktionssvetsning som sammanfogningsmetod för det kvävelegerade pulvermetallurgiskt framställda stålet Uddeholm Vanax SuperClean. Vanax SuperClean kan inte svetsas med smältsvetsmetoder där grundmaterialet smälter, på grund av kvävgasbildning som resulterar i undermåliga svetsfogar. Kostnaden för materialet motiverar användandet av Vanax SuperClean för kritiska delar i applikationer, kombinerat med ett mindre kostsamt material till övriga delar, vilket föranleder undersökning av alternativa sammanfogningsmetoder. Vanax SuperClean friktionssvetsas mot sig själv, såväl som mot Uddeholmsstålen Stavax ESR och UHB 11. Prov tas fram för ett antal undersökningar. Mikrostruktur undersöks med mikroskopi, mikrohårdhetsprovning utförs enligt Vickersprincipen, restaustenitnivåer mäts med röntgendiffraktion och dragprovning utförs. Lyckade svetsfogar fås i alla undersökta prover, vilket visar att svetsmetoden är lämplig för Vanax SuperClean och att varken förvärmning eller långsamt svalnande av arbetsstycken krävs. Möjligheten att använda friktionsomrörningssvetsning som sammanfogningsmetod för Vanax SuperClean diskuteras.