Σε αυτή την διπλωματική στο ΠΜΣ Επιστημής Υλικών, έγινε προσπάθεια δημιουργίας νέων πλασμονικών δομών, μέσω της οξείδωσης μεταβατικών μετάλλων από τα στερεά τους διαλλύματα που αναπτύχθηκαν μέσω της τεχνικής της ιοντοβολής. Ελέγχοντας, την διεθνή βιβλιογραφία δεν βρέθηκε τρόπος παρεμφερής της πειραματικής διαδικασίας που ακολουθήθηκε, για την επίτευξη πλασμονικών δομών. Τα συστήματα που μελετήθηκαν είναι υμένια CuO / Au και Cu2O / Au, όπου η διηλεκτρική μήτρα είναι το ημιαγώγιμο οξείδιο και το πλασμονικό μέταλλο είναι το ευγενές μέταλλο του Au. Επίσης, να σημειωθεί ότι έλαβαν χώρα προκαταρκτικά πειράματα με χρήση NiO, όπου και αποδεικνύεται η γενικότητα της μεθοδολογίας, που ακολουθείται. Συνολικά, υπήρξαν τρεις διαφορετικές συγκεντρώσεις σε Au στα υμένια, οι οποίες πιστοποιήθηκαν μέσω της τεχνικής EDS. Πέραν, του επηρεασμού που δέχτηκαν τα ημιαγώγιμα οξείδια του χαλκού στο ενεργειακό διάκενο (υπολογισμός μέσω φασματοσκοπίας απορρόφησης ορατού / υπεριώδους UV / VIS), εξαιτίας της δημιουργίας διαφορετικών παχών υμενίου (φαινόμενα κβαντικού περιορισμού) και της παρουσίας του ευγενούς μετάλλου (Au), το σημαντικότερο σημείο είναι αυτό που αφορά την μελέτη και παρατήρηση εντοπισμένων επιφανειακών πλασμονικών συντονισμών (υπολογισμός μέσω τεχνικής UV / VIS), των λεγόμενων Localized Surface Plasmon Resonances – LSPR, τα οποία σχετίζονται με την απόκριση των ηλεκτρονίων αγωγιμότητας των μεταλλικών νανοσωματίδίων (< 100 nm) με μέγεθος μικρότερο από το μήκος κύματος της προσπίπτουσας ακτινοβολίας. Επιπρόσθετα, παρουσιάζονται κάποια διαγράμματα που αφορούν επιφανειακούς πλασμονικούς συντονισμούς σε μεταλλικά υμένια Au – Cu. Οι συντονισμοί LSPR μελετήθηκαν για διάφορους ρυθμούς ανόπτησης και για διάφορες συγκεντρώσεις. / In this thesis, an attempt was made to create new plasmonic structures, through the technique of sputtering. Going through the literature we could not find way similar experimental procedure followed to achieve plasmonic structures. The systems that have been studied are films CuO / Au and Cu2O / Au, wherein the dielectric matrix is semiconductor oxide and the plasmon metal is a noble metal of Au. Overall, there were three different concentrations of Au in the films, which were identified through EDS. In addition, the influence of thin film thickness on the energy gap due to quantum confinement was studied. The most important point is the observation of localized surface plasmon resonances (calculation through UV / VIS), the so-called LSPR, which are related to the response of the free electrons of metal nanoparticles (<100 nm) to the electric field of light. Resonances LSPR studied for various annealing rates and different concentrations of gold. We have to say that, after the appropriate annealing, we observed the creation of solid solutions (XRD).

Nanostructured materials especially, one-dimensional (1D) nanostructures have unique physical, chemical, mechanical properties and are the building blocks for a range of nanoscale devices. The procedure employed for the synthesis of nanostructures involves the use of sophisticated instruments or rigorous chemical reactions. The motivation of our work is to develop a strategy that is simple, cost effective and applicable to a host of oxide materials. Nanostructures of various oxides have been grown from the metal as the source material. 1D ZnO nanostructures have been obtained by simply heating Zn metal in ambient air at temperatures below 600 °C. The nanostructures grow on the surface of the source material and the morphology is controlled by monitoring the curvature of the source material. This technique has an added advantage that neither any catalyst nor any gas flow is required. Tetrapods of ZnO are obtained when Zn is heated above 700 °C in ambient air. It has been shown that the morphology and the aspect ratio (length-to-diameter ratio) of the tetrapods depend on the temperature and the temperature gradient. Photoluminescence studies reveal good optical quality ZnO nanostructures. The technique employed to synthesize 1D ZnO nanostructures has been checked for other oxides. The temperature required for the synthesis of Ga2O3 nanostructures is 1200 °C. Many researchers have shown that Ga2O3 emits in the blue-green region. A red emission is required to get the impression of white light which has been seen for nitrogen doped Ga2O3. As the temperature is very high and Ga is heated in ambient air, unintentional nitrogen doping of 1D Ga2O3 nanostructures is obtained which is the reason for white light emission. The morphology of Ga2O3 nanostructures has been controlled by monitoring the curvature of the starting material as is the case of ZnO. Similar technique has also been employed for the synthesis of CuO nanostructures. The morphology is temperature dependent and 1D CuO nanostructures are obtained when the synthesis temperature is between 400 and 600 C. Possible growth mechanisms have been proposed for all these oxide materials. The entire thesis is based on the results discussed above. It has been organized as follows: Chapter 1 deals with the introduction to nanostructures, importance of 1D nanostructures, the specific applications of different morphologies, materials that are widely explored in the synthesis of nanostructures and different approaches to the synthesis of nanostructures. Growth mechanisms like VLS, VS and SLS are briefly discussed. A brief review on the basic physical properties, applications and different morphologies of ZnO, Ga2O3 and CuO is outlined with emphasis to the various synthesis techniques. Finally the aim and scope of the present work is discussed. Chapter 2 describes the experimental setup used for the synthesis and the basic principles of characterization techniques like x-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), energy dispersive spectrum (EDS), electron energy loss spectroscopy (EELS), photoluminescence (PL), Raman spectroscopy, x-ray photoelectron spectroscopy (XPS), UV-Visible spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR) and thermogravimetric analysis (TGA). Chapter 3 deals with the synthesis of 1D ZnO nanostructures with different morphologies such as nanoneedles, nanorods, nanobelts from Zn powder/granule. The growth process is found to be different from the conventional VS mechanism. The advantage and the versatility of the method is emphasized. In this method, neither a catalyst nor any gas flow is required for the synthesis of oxide nanostructures. Depending upon the Zn powder or Zn granules as the starting material different nanostructures of ZnO have been synthesized. The as-synthesized materials are characterized by XRD, SEM, HRTEM, EDS, TGA and Raman spectroscopy and the results are discussed. Chapter 4 describes the controlled growth of ZnO tetrapods and the influence of temperature and temperature gradient on the growth process. Though there are several methods to synthesize ZnO tetrapods and it has been established that ZnO tetrapods can be synthesized by heating Zn in air, it is advantageous to grow tetrapods of different morphologies with different lengths. The large scale synthesis of ZnO tetrapods by heating Zn in air ambient is discussed in this chapter. The key parameters that control the diameter, length, and morphology of tetrapods are identified. It is shown that the morphology and dimensions of the tetrapods depend not only on the vaporization temperature but also on the temperature gradient of the furnace. The influence of vaporization temperature and growth temperature on the morphology of the tetrapods is discussed elaborately. Chapter 5 explains the one-step synthesis of nitrogen doped Ga2O3 nanostructures of different morphologies and the different growth mechanisms. The experimental method employed for the synthesis of nanostructures is simple and is different from the other reported methods. Neither any catalyst/substrate preparation nor any gas flow is required for the synthesis of Ga2O3 nanostructures. The synthesis involves the heating of molten Ga at high temperatures. Single crystalline monoclinic phase of nitrogen-doped Ga2O3 nanorods, nanobelts and nanoneedles are obtained by this method. The morphology is controlled by monitoring the curvature of the Ga droplet which is achieved by using different substrates. Possible growth processes of different morphology have been proposed. Chapter 6 includes some surprising results on the white light emission of Ga2O3 nanorods. High synthesis temperature generates a high vapor pressure suitable for the growth of Ga2O3 nanorods, creates oxygen vacancy and incorporates nitrogen from the ambient. The oxygen vacancy is responsible for the bluish-green emission, while nitrogen is responsible for the red emission. As a consequence, white light emission is observed from Ga2O3 nanorods when irradiated with UV light. The interesting point is that neither post-treatment of the nanorods nor size control is required for white light emission. Chapter 7 describes the synthesis of CuO nanostructures by heating Cu foil in air ambient. This is an attempt to check whether the synthesis technique employed for ZnO and Ga2O3 is applicable to other oxides. The as-synthesized CuO nanostructures are characterized by XRD, SEM, HRTEM, EDS, TGA, UV-visible, FTIR and the results are discussed. Chapter 8 gives the conclusions and the overall summary of the thesis.

Le travail de thèse est consacré à la synthèse, l’élaboration et à l’étude des propriétés physiques d’une famille d’oxydes semi-conducteurs BiVO4 sous formes de nanostructures et de films minces incluant un dopage métallique (Metal = Cu, Mo et Ag) dans le but de réaliser des photocatalyseurs efficaces sous irradiation en lumière visible. La synthèse de nanopoudres dopées a ainsi été effectuée par la technique de broyage planétaire à haute énergie ainsi que par la méthode sol-gel. Les matériaux obtenus et les effets de dopage ont été étudiés sur les caractéristiques structurales, électroniques et optiques. En conjuguant des études par XPS, Raman et RPE, nous avons montré que le dopage substitutionnel est effectivement réalisé pour les ions (Cu, Mo) localisés dans les sites cristallins des ions vanadium alors que le dopage par l’élément Ag contribue à former des clusters métalliques localisés à la surface de nanoparticules de BiVO4 formant ainsi des nanocomposites. Les réactions photocatalytiques ont été étudiées par la dégradation de colorants organiques (Acide bleu 113, méthyle orange (MO)) dans des solutions faiblement concentrées. Parmi les ions dopants substitués dans les matrices hôtes, le dopage au cuivre (Cu2+) a montré de meilleures performances en raison d'une augmentation de la densité de charges photo-générées et de la conductivité électrique par rapport au cas du dopage au molybdène. Pour le dopage à l’argent, la formation de clusters métalliques donnent lieu à des effets de résonances plasmoniques qui améliorent l'efficacité photocatlytique à un niveau équivalent à celui du dopage substitutionnel au cuivre. La deuxième contribution de ce travail a porté sur la réalisation par pulvérisation cathodique rf-magnétron de films minces BiVO4 dopés par des éléments Mo et Cu dans des conditions définies par l'atmosphère de dépôt à base de pressions partielles d’un gaz Ar ou d’un mélange Ar / O2 et des températures de substrats variables jusqu'à 450 ° C. Les paramètres optimaux de dépôt ont été identifiés pour réaliser des films cristallins à faible rugosité de surfaces ou à morphologies en nano-îlots. Des études photocatalytiques utilisant des films minces dopés ont été effectuées par la dégradation des colorants organiques (MO) sous rayonnement visible. Ces études montrent que la morphologie des films avec des surfaces spécifiques importante est aussi un facteur d’amplification des performances photocatalytiques des films minces dopés Me-BiVO4. / The thesis work is devoted to the synthesis and investigations of the physical properties of a family of semiconducting oxides based on BiVO4 as nanostructures or thin films including a metal doping (Metal = Cu, Mo and Ag) in order to achieve effective photocatalysts under visible light irradiation. The synthesis of doped nanopowders was carried out by the techniques of high-energy ball milling and sol-gel. The resulting materials and doping effects were characterized on the structural, electronic and optical properties. By combining XPS, Raman and EPR studies, it was shown that the substitutional doping is achieved for the doping ions (Cu, Mo) being located in the lattice sites of the vanadium ions. Oppositely, Ag doping contributes to form Ag metal clusters located on the surface of nanoparticles of BiVO4 thereby forming nanocomposites. Photocatalytic reactions were studied by the degradation of organic dyes (Acid Blue 113, methyl orange (MO)) in low concentrated solutions. Among the doping ions substituted in the host matrices, Cu2+ showed better photocatalytic performances because of an increase in the density of photo-generated charges and similar effect on the electrical conductivity compared to the case of Mo doping. In the Ag based nanocomposites, the formation of metal clusters seems to induce surface resonance plasmonic effects that improve the efficiency of photocatalytic reactions with respect to the activity demonstrated for substitutional doping. The second contribution of the thesis work was devoted to BiVO4 thin films deposition by rf sputtering process with Mo and Cu doping under defined synthesis conditions such as the partial pressures of Ar gas or an Ar / O2 mixture and varying the substrate temperatures up to 450 ° C. The optimal deposition parameters have been identified to achieve crystalline films with low roughness surface or alternatively with nano-islands morphologies. Photocatalytic studies using doped thin films were carried out through the degradation of organic dyes (MO) under visible light irradiation. The performed measurements show that the film morphology with high specific surface is also a key factor in the amplification of photocatalytic reactions in metal doped thin films.

This work is part of the inter-laboratory collaboration to study the stability of seven distinct sets of state-of-the-art organic photovoltaic (OPV) devices prepared by leading research laboratories. All devices have been shipped to and degraded at RISØ-DTU up to 1830 hours in accordance with established ISOS-3 protocols under defined illumination conditions. In this work, we apply the Incident Photon-to-Electron Conversion Efficiency (IPCE) and the in situ IPCE techniques to determine the relation between solar cell performance and solar cell stability. Different ageing conditions were considered: accelerated full sun simulation, low level indoor fluorescent lighting and dark storage. The devices were also monitored under conditions of ambient and inert (N2) atmospheres, which allows for the identification of the solar cell materials more susceptible to degradation by ambient air (oxygen and moisture). The different OPVs configurations permitted the study of the intrinsic stability of the devices depending on: two different ITO-replacement alternatives, two different hole extraction layers (PEDOT:PSS and MoO3), and two different P3HT-based polymers. The response of un-encapsulated devices to ambient atmosphere offered insight into the importance of moisture in solar cell performance. Our results demonstrate that the IPCE and the in situ IPCE techniques are valuable analytical methods to understand device degradation and solar cell lifetime. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

This work is part of the inter-laboratory collaboration to study the stability of seven distinct sets of state-of-the-art organic photovoltaic (OPV) devices prepared by leading research laboratories. All devices have been shipped to and degraded at RISØ-DTU up to 1830 hours in accordance with established ISOS-3 protocols under defined illumination conditions. In this work, we apply the Incident Photon-to-Electron Conversion Efficiency (IPCE) and the in situ IPCE techniques to determine the relation between solar cell performance and solar cell stability. Different ageing conditions were considered: accelerated full sun simulation, low level indoor fluorescent lighting and dark storage. The devices were also monitored under conditions of ambient and inert (N2) atmospheres, which allows for the identification of the solar cell materials more susceptible to degradation by ambient air (oxygen and moisture). The different OPVs configurations permitted the study of the intrinsic stability of the devices depending on: two different ITO-replacement alternatives, two different hole extraction layers (PEDOT:PSS and MoO3), and two different P3HT-based polymers. The response of un-encapsulated devices to ambient atmosphere offered insight into the importance of moisture in solar cell performance. Our results demonstrate that the IPCE and the in situ IPCE techniques are valuable analytical methods to understand device degradation and solar cell lifetime. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.