We have extended the HOLA molecular dynamics (MD) code to run slider-on-block friction experiments for Al and Cu. Both objects are allowed to evolve freely and show marked deformation despite the hardness difference. We recover realistic coefficients of friction and verify the importance of cold-welding and plastic deformations in dry sliding friction. Our first data also show a mechanism for decoupling between load and friction at high velocities. Such a mechanism can explain an increase in the coefficient of friction of metals with velocity. The study of the effects of currents on our system required the development of a suitable electrodynamic (ED) solver, as the disparity of MD and ED time scales threatened the efficiency of our code. Our first simulations combining ED and MD are presented. / text

The goal of this master thesis is to suggest a methodology for a visualization history of changes in cadastral maps. The suggested methodology takes into account a selection of original historical and contemporary data, processing workflow and follow-up visualization using existing open source web technologies. The greatest contribution of this thesis is in the design of the spatio-temporal database, because currently there does not exist workable editor similar to it, which could be used for creating such data. The suggested procedure is based on database updating method of ISKN database utilizing amendment records. However this method is significantly simplified with the use of PostgreSQL/PostGIS geospatial functions. The available literature and other informational sources to the topic are overviewed in the first part of the master thesis. The term "spatio-temporal data" is thoroughly defined and also the ways of integrating temporal features into spatial data, methods of visualization of spatio-temporal data and recent state of their implementations into desktop platforms and web applications are noted. Furthermore historical and current data sources and their usability for the master thesis are described. The full methodology of pre-processing and processing of data and a subsequent visualization using...

In this diploma thesis is completed the FEM analysis of connecting rod in combustion engine Briggs & Stratton of the garden lawnmower. Within the frame of computing in the FEM system ANSYS Workbench is solved static structural strein and stress analysis, buckling analysis a fatigue also. The boundary conditions for FEM computing come out from the kinematic and dynamic analysis of the crank-slider mechanism in combustion engine. The 3-D models of the crank-slider mechanism are created in parametric SolidWorks modeller. Own construction variants of the connecting rod based on results of FEM analysis are also designed.

Die vorliegende Arbeit verfolgte die Zielstellung der Substitution des etablierten Weißmetalls als Laufschicht von hydrodynamischen Mehrflächengleitlagern durch neuartige Kunststoffschichten. Dazu wurden vergleichende Bauteilversuche an Mehrflächengleitlagern mit verschiedenen Laufschichten und Bohrungsformen vorgenommen. Eine Zinnbasislegierung als Laufflächenbeschichtung diente dabei als Referenzwerkstoff. Zur Durchführung des Versuchsprogrammes kam ein vorhandener, messtechnisch neu konditionierter Turbinenlagerprüfstand zum Einsatz. Die Versuchsreihen haben durchweg positive Beurteilungen der Lagerkennwerte im untersuchten Betriebsbereich der neuen Lagervarianten ergeben. Die neuartigen Laufschichtvarianten erfüllten die hohen tribologischen und thermischen Anforderungen. Einzelne Abweichungen der ermittelten Kennwerte wurden zahlenmäßig dokumentiert und können mit bereits verfügbaren physikalischen Modellen beschrieben werden. Die Ergebnisse erwiesen sich als unabhängig von der Lagerbauform aber abhängig von der gewählten Schichtvariante. Die Untersuchungen zum Betriebsverhalten unter hydrodynamischer Dauerbelastung sowie im Mischreibungsgebiet und im Notlaufbetrieb führten zu teilweise unterschiedlichen Ergebnissen. Im Mischreibungsgebiet wiesen die untersuchten Lager kaum Unterschiede im Betriebsverhalten auf. Im Dauerversuch zeigten die Lager mit Weißmetall, Gleitlack und Keramikschicht hervorragende Eigenschaften. Die Variante Klüberplast besaß eine ungenügende Bindefestigkeit und führte zu plastischen Verformungen der Schicht infolge der hydrodynamischen Drücke. Im Notlaufbetrieb übertrafen die untersuchten Kunststoffvarianten die Standzeiten des Referenzwerkstoffs Weißmetall. / The aim of this study was to identify and test an alternative liner material instead of common liner materials such as white alloy for multi-lobe radial bearings. For this purpose comparative tests with different radial bearings were carried out. The white alloy material was taken as a reference. In preparation for these test series, the measurement system of the turbine bearing test rig was upgraded. Experiments showed beneficial performances of the bearings with a plastic liner by evaluating the static and dynamic properties of different bearing geometries and liner thicknesses under a wide range of operating conditions. The new bearings fulfilled the high tribological and thermal requirements. Observed deviations of the determined parameters were documented in number and can be described with available physical models. The results were independent of the bearing type and depending on the selected liner material variant. The studies on operating performance in continuous operation in the mixed friction area and in dry running operation led to partially different results. The mixed friction tests showed little difference in the examined stock performance. The bearings with white alloy, ceramic layer and bonded coating showed excellent fatigue properties of long-term experiment. On Klüberplast insufficient bonding strength and plastic deformation of the layer due to the hydrodynamic pressure was found. In the dry running operation the investigated polymers exceeded the lifetime of the referencematerial white alloy.

Research on mixed devices in web surveys is in its infancy. Using a randomized experiment, we investigated device effects (desktop PC, tablet and mobile phone) for six response formats and four different numbers of scale points. N=5,077 members of an online access panel participated in the experiment. An exact test of measurement invariance and Composite Reliability were investigated. The results provided full data comparability for devices and formats, with the exception of continuous Visual Analog Scale (VAS), but limited comparability for different numbers of scale points. There were device effects on reliability when looking at the interactions with formats and number of scale points. VAS, use of mobile phones and five point scales consistently gained lower reliability. We suggest technically less demanding implementations as well as a unified design for mixed-device surveys.

The main purpose of this project is to investigate different tool steels in terms of their ability to withstand material transfer buildup, so-called galling, occurring in SMF (sheet metal forming) operations. The ability to withstand galling is vital to optimize cost-effectiveness and increase the work tool’s effective operational time. This investigation studies four different tool steels, including a TiN-coating, with the intention of evaluating the microstructures, chemical composition and hardness effect on galling resistance in dry conditions using a slider-on-flatsurface (SOFS) tribo-tester which measures the coefficient of friction during sliding. An OP (optical profilometer) was used to measure the size and geometry of lump growth on the tool and damage on the work sheet. A scanning electron microscope (SEM) was used to identify the interacting tribological mechanisms exhibited at different stages during the slide. The SEM figures confirmed three different types of characteristic patterns exhibited in the tracks after tribo- testing which were categorized as mild adhesive, abrasive and severe adhesive damage. A SEM figure that illustrates a ragged contact surface and an obvious change in the sheet materials plastic behavior is in this report regarded as a sign of severe adhesive contact, the characteristics could possibly be explained by local high temperature and high pressure followed by a sudden pressure drop and creation of hardened welds or solders between the two surfaces which increase the frictional input needed for further advancement. Friction coefficients observed in the initial 100% mild adhesive stage were, μ=0,22-0,26 succeeded by abrasive SEM characteristics often in association with mild adhesive contact and friction values between μ=0,25-0,4 which where sometimes followed by severe adhesive SEM characteristics in 100% of the contact zone with friction values between μ=0,34- 0,9 respectively. The tool material that performed best according to the friction detection criteria was Sv21 closely followed by Sleipner (TiN coated) and Va40 (HRC 63.3). Unfortunately was the friction criteria, a significant raise in friction for defining a sliding length to galling, not adequate for dry conditions due to immediate material transfer succeeded by cyclic changes between partial or 100% abrasive+mild adhesive and severe adhesive contact. The mechanism that change abrasive wear in association with mild adhesive contact, (moderate friction input), to sever adhesive wear, (higher friction input), is dependent on lump shape (lump geometry) and can appear at comparably low speeds 0,04-0,08 [m/s] and low friction energy input (μ=0,34), the magnitude of the change in friction is therefore not always significant and hardly detectable on the friction graph. This was quite unexpected but could be explained by concentration of friction energy rater than the absolute amount. The problem with using friction graphs for galling evaluation was increased even further when a very small lump size and low corresponding rate of material transfer to the tool surface caused a sustainable high raise in friction (μ≈0,3→0,6) on a TiN-coated tool steel called Sleipner. A hardly detectable or similar friction raise for Sv21 and Va40 showed much larger corresponding lump size and rate of material transfer. This means that friction graphs demonstrate a clear problem with quantifying lump size [m3] and rate of  material transfer [m3/s]. Another phenomenon called stick slip behavior, material transfer and lump growth followed by a sudden decrease in lump size and transfer of material back to the work sheet, is also not possible to detect on a friction graph. Because a drop in friction can easily be a change in contact temperature and lump attack angle due to a growing lump and not a decreasing lump.   The conclusion, a friction graph is not suited for galling evaluation and ranking in dry SOFS conditions. A ranking should primarily be based on dimensional OP measurements of the cross section of formed tracks and scratches or preferably by repeated OP measurements of the tool surface during a single test, the last revel the exact lump growth history and true lump growth even in the sliding direction. / civilingenjörsexamen

<p>The main purpose of this project is to investigate different tool steels in terms of their ability to withstand material transfer buildup, so-called galling, occurring in SMF (sheet metal forming) operations. The ability to withstand galling is vital to optimize cost-effectiveness and increase the work tool’s effective operational time. This investigation studies four different tool steels, including a TiN-coating, with the intention of evaluating the microstructures, chemical composition and hardness effect on galling resistance in dry conditions using a slider-on-flatsurface (SOFS) tribo-tester which measures the coefficient of friction during sliding.</p><p>An OP (optical profilometer) was used to measure the size and geometry of lump growth on the tool and damage on the work sheet. A scanning electron microscope (SEM) was used to identify the interacting tribological mechanisms exhibited at different stages during the slide. The SEM figures confirmed three different types of characteristic patterns exhibited in the tracks after tribo- testing which were categorized as mild adhesive, abrasive and severe adhesive damage.</p><p>A SEM figure that illustrates a ragged contact surface and an obvious change in the sheet materials plastic behavior is in this report regarded as a sign of severe adhesive contact, the characteristics could possibly be explained by local high temperature and high pressure followed by a sudden pressure drop and creation of hardened welds or solders between the two surfaces which increase the frictional input needed for further advancement. Friction coefficients observed in the initial 100% mild adhesive stage were, μ=0,22-0,26 succeeded by abrasive SEM characteristics often in association with mild adhesive contact and friction values between μ=0,25-0,4 which where sometimes followed by severe adhesive SEM characteristics in 100% of the contact zone with friction values between μ=0,34- 0,9 respectively. The tool material that performed best according to the friction detection criteria was Sv21 closely followed by Sleipner (TiN coated) and Va40 (HRC 63.3). Unfortunately was the friction criteria, a significant raise in friction for defining a sliding length to galling, not adequate for dry conditions due to immediate material transfer succeeded by cyclic changes between partial or 100% abrasive+mild adhesive and severe adhesive contact. The mechanism that change abrasive wear in association with mild adhesive contact, (moderate friction input), to sever adhesive wear, (higher friction input), is dependent on lump shape (lump geometry) and can appear at comparably low speeds 0,04-0,08 [m/s] and low friction energy input (μ=0,34), the magnitude of the change in friction is therefore not always significant and hardly detectable on the friction graph. This was quite unexpected but could be explained by concentration of friction energy rater than the absolute amount. The problem with using friction graphs for galling evaluation was increased even further when a very small lump size and low corresponding rate of material transfer to the tool surface caused a sustainable high raise in friction (μ≈0,3→0,6) on a TiN-coated tool steel called Sleipner.</p><p>A hardly detectable or similar friction raise for Sv21 and Va40 showed much larger corresponding lump size and rate of material transfer. This means that friction graphs demonstrate a clear problem with quantifying lump size [m3] and rate of  material transfer [m3/s]. Another phenomenon called stick slip behavior, material transfer and lump growth followed by a sudden decrease in lump size and transfer of material back to the work sheet, is also not possible to detect on a friction graph. Because a drop in friction can easily be a change in contact temperature and lump attack angle due to a growing lump and not a decreasing lump.</p><p> </p><p>The conclusion, a friction graph is not suited for galling evaluation and ranking in dry SOFS conditions. A ranking should primarily be based on dimensional OP measurements of the cross section of formed tracks and scratches or preferably by repeated OP measurements of the tool surface during a single test, the last revel the exact lump growth history and true lump growth even in the sliding direction.</p><p> </p> / civilingenjörsexamen

Die vorliegende Arbeit verfolgte die Zielstellung der Substitution des etablierten Weißmetalls als Laufschicht von hydrodynamischen Mehrflächengleitlagern durch neuartige Kunststoffschichten. Dazu wurden vergleichende Bauteilversuche an Mehrflächengleitlagern mit verschiedenen Laufschichten und Bohrungsformen vorgenommen. Eine Zinnbasislegierung als Laufflächenbeschichtung diente dabei als Referenzwerkstoff. Zur Durchführung des Versuchsprogrammes kam ein vorhandener, messtechnisch neu konditionierter Turbinenlagerprüfstand zum Einsatz. Die Versuchsreihen haben durchweg positive Beurteilungen der Lagerkennwerte im untersuchten Betriebsbereich der neuen Lagervarianten ergeben. Die neuartigen Laufschichtvarianten erfüllten die hohen tribologischen und thermischen Anforderungen. Einzelne Abweichungen der ermittelten Kennwerte wurden zahlenmäßig dokumentiert und können mit bereits verfügbaren physikalischen Modellen beschrieben werden. Die Ergebnisse erwiesen sich als unabhängig von der Lagerbauform aber abhängig von der gewählten Schichtvariante. Die Untersuchungen zum Betriebsverhalten unter hydrodynamischer Dauerbelastung sowie im Mischreibungsgebiet und im Notlaufbetrieb führten zu teilweise unterschiedlichen Ergebnissen. Im Mischreibungsgebiet wiesen die untersuchten Lager kaum Unterschiede im Betriebsverhalten auf. Im Dauerversuch zeigten die Lager mit Weißmetall, Gleitlack und Keramikschicht hervorragende Eigenschaften. Die Variante Klüberplast besaß eine ungenügende Bindefestigkeit und führte zu plastischen Verformungen der Schicht infolge der hydrodynamischen Drücke. Im Notlaufbetrieb übertrafen die untersuchten Kunststoffvarianten die Standzeiten des Referenzwerkstoffs Weißmetall. / The aim of this study was to identify and test an alternative liner material instead of common liner materials such as white alloy for multi-lobe radial bearings. For this purpose comparative tests with different radial bearings were carried out. The white alloy material was taken as a reference. In preparation for these test series, the measurement system of the turbine bearing test rig was upgraded. Experiments showed beneficial performances of the bearings with a plastic liner by evaluating the static and dynamic properties of different bearing geometries and liner thicknesses under a wide range of operating conditions. The new bearings fulfilled the high tribological and thermal requirements. Observed deviations of the determined parameters were documented in number and can be described with available physical models. The results were independent of the bearing type and depending on the selected liner material variant. The studies on operating performance in continuous operation in the mixed friction area and in dry running operation led to partially different results. The mixed friction tests showed little difference in the examined stock performance. The bearings with white alloy, ceramic layer and bonded coating showed excellent fatigue properties of long-term experiment. On Klüberplast insufficient bonding strength and plastic deformation of the layer due to the hydrodynamic pressure was found. In the dry running operation the investigated polymers exceeded the lifetime of the referencematerial white alloy.