京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第21066号 / 工博第4430号 / 新制||工||1688(附属図書館) / 京都大学大学院工学研究科建築学専攻 / (主査)教授 西山 峰広, 教授 原田 和典, 教授 河野 広隆 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

京都大学 / 0048 / 新制・課程博士 / 博士(理学) / 甲第20924号 / 理博第4376号 / 新制||理||1628(附属図書館) / 京都大学大学院理学研究科地球惑星科学専攻 / (主査)教授 田上 高広, 教授 山路 敦, 教授 平原 和朗 / 学位規則第4条第1項該当 / Doctor of Science / Kyoto University / DGAM

No description available.

No description available.

No description available.

<p>The objectives of this investigation were to experimentally and analytically evaluate the  performance of a valve train cam and oscillating roller follower mechanism. Of particular interest  was the effect of operating conditions on the slide-to-roll ratio (SRR) of the roller follower. In order to experimentally measure the SRR at the cam-roller contact, a valve train test rig  (VTTR) was utilized. The VTTR contained a section of a heavy-duty diesel engine valve train that  was instrumented with encoders and Hall effect sensors to measure the camshaft and roller  follower angular velocities as a function of operating parameters.  To corroborate the experimental with analytical results, a numerical model for the cam and  oscillating roller follower was developed. In this modeling approach, the roller angular velocity  was determined via a torque balance between the frictional torque of the pin-roller follower and  cam-roller follower interfaces. The pin-roller friction was obtained by developing a time-dependent hydrodynamic journal bearing model with variable speed and load. Friction maps were  developed for the cam-roller follower interface using a ball-on-disk EHD2 rig to capture the  friction behavior across a range of entraining velocities, contact pressures, and SRRs. Additional  areas of investigation included thermal effects and wear in the pin-roller contact. Overall, good agreement was obtained between the experimental and analytical roller  follower angular velocity, with the normalized RMS errors less than 7%, across all operating  conditions investigated. The analytical investigation determined that thermal effects in the pin-roller contact are insignificant for the typical operating conditions. However, it was shown that the  pin-roller friction torque is critical in causing roller follower slip, as the SRR greatly increases  once the pin-roller friction torque is greater than the cam-roller friction torque. Finally, pin-roller  local wear was demonstrated to have detrimental effects on the SRR of the roller follower once a  critical wear depth was reached. </p>

No description available.

No description available.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第23891号 / 工博第4978号 / 新制||工||1777(附属図書館) / 京都大学大学院工学研究科材料工学専攻 / (主査)教授 辻 伸泰, 教授 乾 晴行, 教授 安田 秀幸 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

The object of this work is to explore the influence superhydrophobic (SH) surfaces exert in laminar jet impingement and when they are combined with riblets in turbulent channel flow. A SH surface generates an apparent slip due to the combination of micropatterning and chemical hydrophobicity. Because of surface tension, water does not enter the cavities between the features, increasing the contact angle of a water droplet on the surface and reducing the liquid-solid contact area. An analysis based on the integral momentum approach of Karman and Pohlhausen is presented that predicts jet impingement behavior on SH surfaces. The model is first applied to the scenario where the slip at the surface is isotropic and a downstream depth is imposed such that a circular hydraulic jump occurs. The model predicts the thin film parameters downstream of the jet and the radial location of the hydraulic jump. An increase in the hydraulic jump radius occurs as slip increases, momentum of the jet increases, or the downstream depth decreases. Modifications to the model are made for the scenario where the slip at the surface varies azimuthally, as would be the case for a surface patterned with microribs. The average behavior is similar, although now an elliptically shaped jump forms with the major axis aligned parallel to the rib/cavity structures. The ellipse eccentricity increases as the slip increases, the jet momentum increases, or the downstream depth decreases. Where there is no downstream depth imposed on SH surfaces, the thin film breaks up into droplets instead of forming a hydraulic jump. Further changes are made to the model to incorporate this behavior for isotropic and anisotropic surfaces resulting in circular and elliptically shaped breakups respectively. This work also explores SH surfaces with riblets in turbulent channel flow. Pressure drop measurements across surfaces exhibiting superhydrophobicity, riblets, and surfaces with both drag reducing mechanisms are presented. The SH surface reduces drag because the effective surface area is reduced and riblets are able to reduce drag by dampening the spanwise turbulence. Photolithography was used to fabricate all surface types. An aluminum channel with a control and a test section was used for testing. Pressure transducers recorded the pressure drop across smooth silicon wafers and patterned test surfaces simultaneously allowing for computation of the friction factors.