A new equivalent circuit of left-handed (LH) microstrip transmission line loaded with Complementary split-ring resonators (CSRRs) is presented. By adding the magnetic coupling into the equivalent circuit, the new equivalent circuit presents a more accurate cutoff frequency than the old one. The group delay of CSRRs applied with microstrip transmission line (TL) is also studied and analyzed into two cases which are passive CSRRs delay line and active CSRRs delay line. In the first case, the CSRRs TL is analyzed. The group delay can be varied and controlled via signal frequency which does not happen in a normal TL. In the active CSRRs delay line, the CSRRs loaded with TL is fixed. The diodes are added to the model between the strip and CSRRs. By observing a specific frequency at 2.03GHz after bias DC voltages from -10V to -20V, the group delay can be moved from 0.6ns to 5.6ns. A novel microstrip filter is presented by embedding CSRRs on the ground plane of microstrip filter. The filter characteristic is changed from a 300MHz narrowband to a 1GHz wideband as well as suppression the occurrence of previous higher spurious frequency at 3.9GHz. Moreover, a high rejection in the lower band and a low insertion loss of <1dB are achieved.Finally, it is shown that CSRRs applied with planar antenna can reduce the antenna size. The structure is formed by etching CSRRs on the ground side of the patch antenna. The meander line part is also added on the antenna patch to tune the operation frequency from 1.8GHz downward to 1.73GHz which can reduce the antenna size to 74% of conventional patch antennas. By using the previous antenna structure without meander line, this proposed antenna can be tuned for selecting the operation frequency, by embedding a diode connected the position between patch and ground. The results provide 350MHz tuning range with 35MHz bandwidth.

Metamaterials offer the freedom to tune the rich electromagnetic coupling between the constituent meta-atoms to tailor their collective electromagnetic response. Therefore, a comprehensive understanding of the nature of electromagnetic interactions between meta-atoms is necessary for novel metamaterial design, which is provided in the first part of this thesis. The subsequent work in the thesis applies the understanding from the first part to design and demonstrate novel one-dimensional metamaterials that overcome the limitations of metamaterials proposed in literature or exhibit electromagnetic responses not previously observed. Split-ring Resonators (SRRs) are a fundamental building block of many electromagnetic metamaterials. In the first part of the work in this thesis, it is shown that bianisotropic SRRs (with magneto-electric cross-polarisation) when in close proximity to each other, exhibit a rich coupling that involves both electric and magnetic interactions. The strength and nature of the coupling between two identical SRRs are studied experimentally and computationally as a function of their separation and relative orientation. The electric and magnetic couplings are characterised and it is found that, when SRRs are close enough to be in each other's near-field, the electric and magnetic couplings may either reinforce each other or act in opposition. At larger separations retardation effects become important. The findings on the electromagnetic interactions between bianisotropic resonators are next applied to developing a one-dimensional ultra-wideband backward-wave metamaterial waveguide. The key concept on which the metamaterial waveguide is built is electro-inductive wave propagation, which has emerged as an attractive solution for designing backward-wave supporting metamaterials. Stacked metasurfaces etched with complementary SRRs (CSRRs) have also been shown to exhibit a broadband negative dispersion. It is demonstrated through experiment and numerical modeling, that the operational bandwidth of a CSRR metamaterial waveguide can be improved by restricting the cross-polarisation effects in the constituent meta-atoms. The metamaterial waveguide constructed using the modified non-bianisotropic CSRRs are found to have a fractional bandwidth of 56.3\% which, based on a thorough search of relevant literature, is the broadest reported value for an electro-inductive metamaterial. A traditional coupled-dipole toy-model is presented as a tool to understand the field interactions in CSRR based metamaterials, and to explain the origin of their negative dispersion response. This metamaterial waveguide should be of assistance in the design of broadband backward-wave metamaterial devices, with enhanced electro-inductive waveguiding effects. In the final part of the thesis, a one-dimensional metamaterial prototype that permits simultaneous forward- and backward-wave propagation is designed. Such a metamaterial waveguide could act as a microwave analogue of nanoparticle chains that support electromagnetic energy transfer with a positive or a negative dispersion due to the excitation of their longitudinal or transverse dipole modes. The symmetry of the designed hybrid meta-atom permits the co-existence of two non-interfering resonances closely separated in frequency. It is experimentally and computationally shown that the metamaterial waveguide supports simultaneous non-interacting forward- and backward-wave propagation in an overlapping frequency band. The proposed metamaterial design should be suitable for realising bidirectional wireless power transfer applications.

Many interesting ideas have emerged from research on electromagnetic eld interactions with di erent materials. Analyzing such interactions has extracted some essential proper- ties of the materials. For example, extracting constitutive parameters such as permittivity, permeability, and conductivity, clari es a material's behavior. In general, the electromag- netic eld interacts with materials either in the far- eld or near- eld of a source. This study focuses on the principle of near- eld microwave microscopy for detection purposes. Many studies have focused on the use of an electrically small resonator, such as a split-ring resonator (SRR) and a complementary split-ring resonator (CSRR), to act as a near- eld sensor for material characterization and detection. At the resonance frequency, the electric and magnetic energy densities are enhanced dramatically at certain locations in the resonator. Any disturbance of the eld around such a resonator with a material under test causes the resonance frequencies to exhibit a shift that is used as an indicator of the sensor sensitivity. In this thesis, a single CSRR is used as a sensing element for detecting cracks in metal surfaces. Many microwave techniques have been developed for crack detection. However, these techniques have at least one of the following drawbacks: working at high frequencies, measurement setup complexity and cost, and low sensitivity. The rst part of this thesis presents a new sensor based on the complementary split-ring resonator (CSRR) that is used to detect sub-millimeter surface cracks. The sensing mechanism is based on perturbing the electromagnetic eld around an electrically small resonator, thus initiating a shift in the resonance frequency. Investigation of the current distribution on a CSRR at the resonance frequency shows the critical location at which the enhanced energy is concentrated. In addition, the current distribution demonstrates the sensing element in the CSRR. The sensor is simple to fabricate and inexpensive, as it is etched-out in the ground plane of a microstrip-line using printed circuit board technology. The microstrip-line excites the CSRR by producing an electric eld perpendicular to the surface of the CSRR. The sensor exhibits a frequency shift of more than 240 MHz for a 200 m crack. In the second part of this thesis, the sensitivity of the sensor is increased by lling the same crack with a dielectric material such as silicon oil. While using CSRR to scan a block with 200 m wide and 2 mm depth dielectric lled crack, the resonance frequency of the sensor shifts 435 MHz more than a case scanning a solid aluminum. Finally, the total Inductance of a CSRR for miniaturizing purposes is increased using either lumped or distributed elements. In this thesis, the designs and the results are validated experimentally and numerically.

The prospect of finding life outside Earth has fascinated mankind for ages, and new technology continuously pushes the boundary of how remote and how obscure evidence we can find. Employing smaller, or completely new, types of landers and robots, and equipping them with miniature instruments would indeed revolutionize exploration of other planets and moons. In this thesis, microsystems technology is used to create a miniature high-precision isotope-resolving molecular spectrometer utilizing the optogalvanic effect. The heart of the instrument, as well as this thesis, is a microplasma source. The plasma source is a split-ring resonator, chosen for its simplicity, pressure range and easily accessible plasma, and modified to fit the challenging application, e.g., by the adding of an additional ground plane for improved electromagnetic shielding, and the integration of microscopic plasma probes to extract the pristine optogalvanic signal. Plasma sources of this kind have been manufactured in both printed circuit board and alumina, the latter for its chemical inertness and for compatibility with other devices in a total analysis system. From previous studies, classical optogalvanic spectroscopy (OGS), although being very sensitive, is known to suffer from stability and reproducibility issues. In this thesis several studies were conducted to investigate and improve these shortcomings, and to improve the signal-to-noise ratio. Moreover, extensive work was put into understanding the underlying physics of the technique. The plasma sources developed here, are the first ever miniature devices to be used in OGS, and exhibits several benefits compared to traditional solutions. Furthermore, it has been confirmed that OGS scales well with miniaturization. For example, the signal strength does not decrease as the volume is reduced like in regular absorption spectroscopy. Moreover, the stability and reproducibility are greatly increased, in some cases as much as by two orders of magnitude, compared with recent studies made on a classical OGS setup. The signal-to-noise ratio has also been greatly improved, e.g., by enclosing the sample cell and by biasing the plasma. Another benefit of a miniature sample cell is the miniscule amount of sample it requires, which can be important in many applications where only small amounts of sample are available. To conclude: With this work, an important step toward a miniature, yet highly performing, instrument for detection of extraterrestrial life, has been taken.

Many interesting ideas have emerged from research on electromagnetic eld interactions with di erent materials. Analyzing such interactions has extracted some essential proper- ties of the materials. For example, extracting constitutive parameters such as permittivity, permeability, and conductivity, clari es a material's behavior. In general, the electromag- netic eld interacts with materials either in the far- eld or near- eld of a source. This study focuses on the principle of near- eld microwave microscopy for detection purposes. Many studies have focused on the use of an electrically small resonator, such as a split-ring resonator (SRR) and a complementary split-ring resonator (CSRR), to act as a near- eld sensor for material characterization and detection. At the resonance frequency, the electric and magnetic energy densities are enhanced dramatically at certain locations in the resonator. Any disturbance of the eld around such a resonator with a material under test causes the resonance frequencies to exhibit a shift that is used as an indicator of the sensor sensitivity. In this thesis, a single CSRR is used as a sensing element for detecting cracks in metal surfaces. Many microwave techniques have been developed for crack detection. However, these techniques have at least one of the following drawbacks: working at high frequencies, measurement setup complexity and cost, and low sensitivity. The rst part of this thesis presents a new sensor based on the complementary split-ring resonator (CSRR) that is used to detect sub-millimeter surface cracks. The sensing mechanism is based on perturbing the electromagnetic eld around an electrically small resonator, thus initiating a shift in the resonance frequency. Investigation of the current distribution on a CSRR at the resonance frequency shows the critical location at which the enhanced energy is concentrated. In addition, the current distribution demonstrates the sensing element in the CSRR. The sensor is simple to fabricate and inexpensive, as it is etched-out in the ground plane of a microstrip-line using printed circuit board technology. The microstrip-line excites the CSRR by producing an electric eld perpendicular to the surface of the CSRR. The sensor exhibits a frequency shift of more than 240 MHz for a 200 m crack. In the second part of this thesis, the sensitivity of the sensor is increased by lling the same crack with a dielectric material such as silicon oil. While using CSRR to scan a block with 200 m wide and 2 mm depth dielectric lled crack, the resonance frequency of the sensor shifts 435 MHz more than a case scanning a solid aluminum. Finally, the total Inductance of a CSRR for miniaturizing purposes is increased using either lumped or distributed elements. In this thesis, the designs and the results are validated experimentally and numerically.

Terahertz (THz) devices are designed to operate from 0.1-10 THz. The THz spectra have unique properties such as penetration through soft materials and reflecting from hard materials, which make THz technologies, a prime candidate for imaging. Plasmons are longitudinal charge oscillations in carrier rich materials. Plasmons can be generated over the channel of transistors inducing a voltage between the source-drain when conditions are satisfied. In this thesis, plasmonic devices operating in the THz region have been studied both theoretically and experimentally investigating GaN/AlGaN and Graphene based transistors. First, we report on a detailed study of dispersion properties of uniform grating gate THz plasmonic crystals, asymmetric dual grating gate plasmonic crystals and with symmetry-breaking defect-like cavities in order to understand the physics behind THz plasmons. For the first time, we defined the dispersion of plasmons in terms of effective plasmonic index. By adding an additional grating on top of the grating gate with a different periodicity, doubles the amount of absorption. Plasmons can be excited when polarization is perpendicular to the gate. We then showed focusing and exciting of THz plasmons polarization independent using circular grating lenses. Sub-micron THz ring resonators are presented showing THz guiding in plasmonic waveguides. So far, resonant sensing has been observed only at cryogenic temperatures since electron mobility is high enough at low temperatures to sustain resonant plasmonic excitation at the channel of the detector. Recently, graphene attracted the attention of the researchers because of its high mobility at room temperature. Room temperature detection has been attempted and achieved, however the detectors have very small responsivity with non-resonant behavior since the graphene is sandwiched and fabrication of such detectors in large scale is impossible with the methods used. Here, we present a resonant room temperature detection of THz with upside down free standing graphene FETs having more than a 400 quality factor, a record high number in the field which is up to 50 times higher than GaN detectors and hundreds of responsivity values with a maximum around 400 V/W which is record high for graphene (10,000 times higher than previously reported graphene detector).

Made available in DSpace on 2014-12-17T14:55:19Z (GMT). No. of bitstreams: 1 MarinaldoPSN_TESE.pdf: 2731148 bytes, checksum: 7c2caa3355d4d42f0702baf0d147bf97 (MD5) Previous issue date: 2014-04-25 / Universidade Federal do Rio Grande do Norte / Metamaterials have attracted a great attention in recent years mostly due to their electromagnetic properties not found in nature. Since metamaterials began to be synthesized by the insertion of artificially manufactured inclusions in a medium specified host , it provides the researcher a broad collection of independent parameters such as the electromagnetic properties of the material host. In this work was presents an investigation of the unique properties of Split Ring Resonators and compounds metamaterials was performed. We presents a theoretical and numerical analysis , using the full-wave formalism by applying the Transverse Transmission Line - LTT method for the radiation characteristics of a rectangular microstrip antenna using metamaterial substrate, as is successfully demonstrated the practical use of these structures in antennas. We experimentally confirmed that composite metamaterial can improved the performance of the structures considered in this thesis / Os metamateriais tem atra?do uma grande aten??o nas ?ltimas d?cadas, principalmente devido as suas propriedades eletromagn?ticas n?o encontradas na natureza. Desde que os metamateriais passaram a ser sintetizados atrav?s da inser??o de inclus?es artificialmente fabricadas num meio hospedeiro especificado, isto propicia ao pesquisador uma larga cole??o de par?metros independentes, tais como as propriedades eletromagn?ticas do material hospedeiro. Neste trabalho foi realizada uma investiga??o das propriedades ?nicas dos Ressoadores em Anel Partido (Split Ring Ressonators - SRR) e dos metamateriais compostos. Apresentou-se uma an?lise te?rica e num?rico-computacional, utilizando o formalismo de onda completa atrav?s da aplica??o do m?todo da Linha de Transmiss?o Transversa LTT, para as caracter?sticas ressonantes de uma antena de microfita com patch retangular utilizando substrato metamaterial, assim como ? demonstrado com sucesso ? utiliza??o pr?tica dessas estruturas em antenas. Esta utiliza??o pr?tica ? confirmada experimentalmente

RF and microwave applications represent one of the fastest-growing segments of the high performance electronics market, where ongoing innovation is critical. Manufacturers compete intensively to meet market needs with reduced cost, size, weight and many other performance criteria demands. Under this scenario, transmission lines based on metamaterial concepts can be considered a very interesting alternative to the conventional transmission lines. They are more compact (compatible with planar manufacturing processes) and present higher degrees of design flexibility. Furthermore, metamaterial transmission lines can also provide many other unique properties not achievable with ordinary transmission lines, such as dispersion or impedance engineering. Nevertheless, the impact in the industry is still not relevant, mostly due to the complexity of the related synthesis and design procedures. These procedures are mainly based on the engineer’s experience, with the help of costly full-wave electromagnetic (EM) simulators and parameter extraction methods. The aim of this thesis is to contribute to simplify and speed up the synthesis and design procedures of artificial transmission lines. In particular, the lines obtained by periodically loading a conventional transmission line with electrically small resonators, such as split ring resonators (SSRs) or its complementary particle (CSRR). The design procedure is automated by using Space Mapping techniques. In contrast to other alternative methods, real synthesis is found from the circuit schematic (that provides a given target response) and without need of human intervention. Some efforts to make the method practical and useful have been carried out. Given a certain target response, it is determined whether it can be physically implemented with a chosen technology, and hence proceeding next to find the synthesis, or not. For this purpose, a two-step Aggressive Space Mapping approach is successfully proposed. In contrast to other methods, the real synthesis is found from certain target circuit values (corresponding to the equivalent circuit model that characterizes the structure to be synthesized). Different efforts have been carried out in order to implement a useful and practical method. Some of them were focused to determine if, given certain circuit parameters (which determine the target response) and certain given technology specifications (permittivity and height of the substrate, technology limits), that response is physically realizable (convergence region). This technique was successfully formulated and it is known as “Two-Step Aggressive Space Mapping Approach”. In this work, the latest improvements made till date, from the synthesis of basic unit cells until different applications and kinds of metamaterial-based circuits, are presented. The results are promising and prove the validity of the method, as well as its potential application to other basic cells and more complex designs. The general knowledge gained from these cases of study can be considered a good base for a coming implementation in commercial software tools, which can help to improve its competitiveness in markets, and also contribute to a more general use of this technology. / Rodríguez Pérez, AM. (2014). Synthesis of Planar Microwave Circuits based on Metamaterial Concepts through Aggressive Space Mapping [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/48465 / TESIS

A two-dimensional isotropic metamaterials formed by crossed split-ring resonators (CSRRs) are studied in this paper. The effective characteristic parameters of this media are determined by quasi-static Lorentz theory. The induced current distributions of a single CSRR at the resonant frequency are presented. Moreover, the dependence of the resonant frequency on the dimensions of single CSRR and the spaces of the array are also discussed. / Singapore-MIT Alliance (SMA)

The study of optical phenomena related to the strong electromagnetic response of noble metals (silver (Ag) and gold (Au) being most popular) over the last couple of decades has led to the emergence of a fast growing research area called plasmonics named after 'surface plasmons' which are electron density waves that propagate along the interface of a metal and a dielectric medium. Surface plasmons are formed by the coupling of light to the electrons on the metal surface subject to the fulfillment of certain physical conditions and they are bound to the metal surface. Depending on whether the metallic medium is a continuous film or a structure having dimensions less than or comparable to the wavelength of the exciting light, propagating or localized surface plasmons can be excited. The structure can be either a hole or an arbitrary pattern in a metal film, or a metallic particle. An array of subwavelength structures can behave as an effective homogeneous medium to incident light and this is the basis of a new class of media known as metamaterials. Metallic metamaterials enable one to engineer the electromagnetic response to  incident light and provide unconventional optical properties like negative refractive index as one prominent example. Metamaterials exhibiting negative index (also called negative index materials (NIMs)) open the door for super resolution imaging  and development of invisibility cloaks. However, the only problem affecting the utilization of plasmonic media to their fullest potential is the intrinsic loss of the metal, and it becomes a major issue especially at visible-near infrared (NIR) frequencies. The frequency of the surface plasmon is the same as that of the exciting light but its wavelength could be as short as that of X-rays. This property allows light of a given optical frequency to be conned into very small volumes via subwave lengthmetallic structures, that can be used to develop ecient sensors, solar cells, antennas and ultrasensitive molecular detectors to name a few applications. Also, interaction of surface plasmons excited in two or more metallic subwavelength structures in close proximity inuences the far-eld optical properties of the overall coupled system. Some eects of plasmonic interaction in certain coupled particles include polarization conversion, optical activity and transmission spectra mimicking electromagnetically-induced transparency (EIT) as observed in gas based atomicsy stems. In this thesis, we mainly focus on the optical properties of square arrays of certain plasmonic structures popularly researched in the last decade. The structures considered are as follows: (1) subwavelength holes of a composite hole-shape providing superior near-eld enhancement such as two intersecting circles (called' double hole') in an optically thick Au/Ag lm, (2) double layer shnets, (3) subwavelength U-shaped particles and (4) rectangular bars. The entire work is based on electromagnetic simulations using time and frequency domain methods. Au/Ag lms with periodic subwavelength holes provide extraordinarily high transmission of light at certain wavelengths much larger than the dimension of the perforations or holes. The spectral positions of the maxima depend on the shape of the hole and the intra-hole medium, thereby making such lms function as a refractive index sensor in the transmission mode. The sensing performance of the double-hole geometry is analyzed in detail and compared to rectangular holes. Fishnet metamaterials are highly preferred when it comes to constructing a NIM at optical frequencies. A shnet design that theoretically oers a negative refractive index with least losses at telecommunication wavelengths (1.4 1.5 microns) is presented. U-shaped subwavelength metallic particles, in particular single-slit split-ring resonators (SSRRs), provide a large negative response to the magnetic eld of light at a specic resonance frequency. The spectral positions of the structural resonances of the U-shaped particle can be found from its array far field transmission spectrum at normal incidence. An effort is made to clarify our understanding of these resonances with the help of localized surface plasmon modes excited in the overall particle. From an application point of view, it is found that a planar square array of SSRRs eectively functions as an optical half-wave waveplate at the main resonance frequency by creating a polarization in transmission that is orthogonal to that of incident light. A similar waveplate eect can be obtained purely by exploiting the near-eld interaction of dierently oriented neighbouring SSRRs. The physical reasons behind polarization conversion in dierent SSRR-array systems are discussed. A rectangular metallic bar having its dipolar resonance in the visible-NIR is called a nanoantenna, owing to its physical length in the order of nanometers. The excitation of localized surface plasmons, metal dispersion and the geometry of the rectangular nanoantenna make an analytical estimation of the physical length of the antenna from the desired dipolar resonance dicult. A practical map of simulated resonance values corresponding to a variation in geometrical parameters of Au bar is presented. A square array of a coupled plasmonic system comprising of three nanoantennas provides a net transmission response that mimicks the EIT effect. The high transmission spectral window possesses a peculiar dispersion profile that enables light with frequencies in that region to be slowed down. Two popular designs of such plasmonic EIT systems are numerically characterized and compared. / <p>QC 20121017</p>