Although current trends in global warming are of great concern, energy demand is still increasing, resulting in increasing pollutant emissions. To address this issue, we need reliable renewable energy sources, lowered pollutant emissions, and efficient and profitable processes for energy conversion. We also need to improve the use of the energy, produced by existing infrastructure. Consequently, the work presented in this thesis aims at investigating current scientific and technological challenges in energy conversion through biomass gasification and the alternative use of fossil fuels, such as diesel, in the generation of cleaner electricity through auxiliary power units in the transport sector. Production of chemicals, syngas, and renewable fuels is highly dependent on the development and innovation of catalytic processes within these applications. This thesis focuses on the development and optimization of catalytic technologies in these areas. One of the limitations in the commercialization of the biomass gasification technology is the effective catalytic conversion of tars, formed during gasification. Biomass contains high amounts of alkali impurities, which pass on to the producer gas. Therefore, a new material with alkali tolerance is needed. In the scope of this thesis, a new catalyst support, KxWO3 – ZrO2 with high alkali resistance was developed. The dynamic capability of KxWO3 – ZrO2 to store alkali metals in the crystal structure, enhances the capture of alkali metals "in situ". Alkali metals are also important electronic promoters for the active phase, which usually increases the catalysts activity and selectivity for certain products. Experimental results show that conversion of 1-methylnaphathalene over Ni/KxWO3 – ZrO2 increases in the presence of 2 ppm of gas-phase K (Paper I). This support is considered to contribute to the electronic equilibrium within the metal/support interface, when certain amounts of alkali metals are present. The potential use of this support can be extended to applications in which alkali "storage-release" properties are required, i.e. processes with high alkali content in the process flow, to enhance catalyst lifetime and regeneration. In addition, fundamental studies to understand the adsorption geometry of naphthalene with increasing temperature were performed in a single crystal of Ni(111) by STM analyses. Chapter 9 presents preliminary studies on the adsorption geometry of the molecule, as well as DFT calculations of the adsorption energy. In relation to the use of clean energy for transport applications, hydrogen generation through ATR for FC-APUs is presented in Papers II to V. Two promoted RhPt bimetallic catalysts were selected in a previous bench scale study, supported on La2O3:CeO2/d – Al2O3 and MgO : Y2O3/CeO2 – ZrO2. Catalyst evaluation was performed in a fullscale reformer under real operating conditions. Results showed increased catalyst activity after the second monolithic catalyst due to the effect of steam reforming, WGS reaction, and higher catalyst reducibility of the RhxOy species in the CeO2 – ZrO2 mixed oxide, as a result of the improved redox properties. The influence of sulfur and coke formation on diesel reforming was assessed after 40 h on stream. Sulfur poisoning was evaluated for the intrinsic activity related to the total Rh and Pt area observed after exposure to sulfur. Sulfur concentration in the aged catalyst washcoat was observed to decrease in the axial direction of the reformer. Estimations of the amount of sulfur adsorbed were found to be below the theoretical equilibrated coverage on Rh and Pt, thus showing a partial deactivation due to sulfur poisoning. / <p>QC 20150213</p>

Reliable energy supply is a major concern and crucial for development of the global society. To address the dependency on fossil fuel and the negative effects of this reliance on climate, there is a need for a transition to cleaner sources. An attractive solution for replacing fossil-based products is renewable substitutes produced from biomass. Gasification and pyrolysis are two promising thermochemical conversion technologies, facing challenges before large-scale commercialization becomes viable. In case of biomass gasification, tar is often and undesired by-product. An attractive option to convert tar into syngas is nickel-based catalytic steam reforming (SR). For biomass pyrolysis, catalytic SR is in early stages of investigation as a feasible option for bio-crude conversion to syngas. The focus of the thesis is partly dedicated to describe research aimed at increasing the knowledge around tar reforming mechanisms and effect of biomass-derived impurities on Ni-based tar reforming catalyst downstream of gasifiers. The work focuses on better understanding of gas-phase alkali interaction with Ni-based catalyst surface under realistic conditions. A methodology was successfully developed to enable controlled investigation of the combined sulfur (S) and potassium (K) interaction with the catalyst. The most striking result was that K appears to lower the sulfur coverage and increases methane and tar reforming activity. Additionally, the results obtained in the atomistic investigations are discussed in terms of naphthalene adsorption, dehydrogenation and carbon passivation of nickel. Furthermore, the thesis describes research performed on pyrolysis gas pre-conditioning at a small-industrial scale, using an iron-based catalyst. Findings showed that Fe-based materials are potential candidates for application in a pyrolysis gas pre-conditioning step before further treatment or use, and a way for generating a hydrogen-enriched gas without the need for bio-crude condensation. / Tillförlitlig energiförsörjning är en stor utmaning och avgörande för utvecklingen av det globala samhället. För att ta möta beroendet av fossil råvara och de negativa effekter som detta beroende medför för klimatet finns ett stort behov av en övergång till renare energiråvaror. En attraktiv lösning är att ersätta nuvarande fossil råvara med produkter från biomassa. Förgasning och pyrolys är två lovande teknologier för termokemisk omvandling av biomassa. Kommersialisering av dessa teknologier är inte helt problemfritt. I fallet förgasning så behöver, bl.a. oönskade tyngre kolväten (tjära) hanteras innan den producerade orenade produktgasen kan användas i syntesgastillämpningar. Ett effektivt alternativ för detta är gaskonditionering vid höga temperaturer, baserade på katalytisk ångreformering med en nickelkatalysator. Katalytisk ångreformering är en möjlig teknik för omvandling av bioråvara, producerad från pyrolys av biomassa, till syntesgas. Avhandlingen fokuserar delvis på att beskriva den forskning som utförts för att öka kunskapen kring mekanismer för tjärreformering och effekterna av föroreningar från biomassan på en nickelkatalysator nedströms förgasare. Arbetet bidrar till en bättre förståelse av hur alkali i form av kalium (K) i gasfasen upptas, jämviktas och växelverkar med ytan hos nickelkatalysatorn under fullt realistiska förhållanden. Inledningsvis utvecklades en metod för att möjliggöra kontrollerade studier av den kombinerade effekten av S och K, vilken inkluderar exakt dosering av alkali till en produktgas, eliminering av transienter i katalysatoraktiviteten samt katalysatorkarakterisering. Det mest lovande resultatet är att K både sänker ytans svavelinnehåll och ökar aktiviteten för omvandlingen av metan och tjära. För att ytterligare fördjupa kunskaperna i mekanismerna för tjärnedbrytning utfördes experimentella och teoretiska ytstudier på en enkristallnickelyta med naftalen som modellförening. Resultat avseende naftalenadsorption, dehydrogenering av naftalen och kolpassivering av nickelytan diskuteras. Därutöver så beskriver avhandlingen den forskning som utförts inom förkonditionering av pyrolysgas med en järnkatalysator för varsam deoxygenering av biooljan och vätgasproduktion. Detta utfördes vid en småskalig industriell anläggning. De experimentella studierna visar att den undersökta järnkatalysatorn resulterar i en vätgasberikad gas och att den är en potentiell kandidat för tillämpning i ett förkonditioneringssteg. / <p>QC 20170830</p>