O Transtorno Afetivo Bipolar (TAB) é um transtorno mental crônico e recorrente. Está situado entre as principais doenças que causam incapacitação e morbidade em todo mundo. A substituição do modelo de atendimento ao doente mental centrado no hospital, por uma rede de serviços prestados na comunidade, tem como conseqüência o aumento do número de pacientes vivendo em família. Estas famílias são solicitadas a oferecer apoio emocional, tolerar estigma, lidar com perdas financeiras e laboral, interrupções na rotina do lar, entre outras. Tais implicações correspondem à sobrecarga que são as conseqüências que o familiar enfrenta ao conviver com pessoa portadora de transtorno mental. O objetivo deste estudo foi identificar e descrever a sobrecarga do TAB nas famílias que convivem com algum portador deste transtorno. Foram entrevistados 15 familiares, sendo três filhos, quatro irmãs, duas cunhadas, uma ex- cunhada, três cônjuges, uma tia e uma mãe. Foram utilizados para a coleta de dados um questionário com informações sobre dados clínicos do paciente com TAB, Critério Padrão de Classificação Econômica Brasil 2008 e roteiro de entrevista semi-estruturado adaptado por Koga (1997) que engloba a sobrecarga familiar. As respostas foram analisadas utilizando-se a técnica de análise de conteúdo de Bardin. O impacto do TAB sobre a família foi descrito nos seguintes aspectos: trabalho, gastos, lazer, relacionamento interpessoal, futuro, recursos e adoecimento do familiar como expressão de sobrecarga. Observou-se que a família se sente mais sobrecarregada nos períodos de crise da doença. Nos períodos estáveis somente os aspectos trabalho e relacionamento interpessoal permanecem como ponto de preocupação e sofrimento familiar. O fato de não se conhecer as causas e tampouco a cura, faz com que apareçam insegurança e temor quanto ao futuro. Este estudo contribuiu para compreender que TAB também sobrecarrega a família que necessita e solicita apoio dos profissionais de saúde para obter melhora na qualidade de vida. A principal limitação do presente estudo é o número pequeno de familiares entrevistados e o fato de todos terem sido recrutados em um único serviço de saúde. Pesquisas semelhantes deverão ser realizadas a fim de verificar se outras famílias manifestam sobrecarga semelhante as apresentadas pelos familiares deste estudo. / The bipolar disorder (BD) is a chronic and recurring mental disorder. Nowadays, it is one of most important disease that is responsible for incapacity and morbidity worldwide. The replacement treatment model of mental illness that was focus at hospital for services accessible to community is responsible for increase of number of patients living in family contexts. These families are responsible to offer emotional support, sometimes tolerate stigma, deal with financial and work loses, disruption at home routine and other ones. These implications are the result of relationship with a person with mental illness. The aim of this study was to identify and describe the burden of bipolar disorder in the family that lives with a person that has this disorder. Questioners were applied for fifteen relatives: tree children, four sisters, tree sistersin- law, tree spouse, 1 aunt and 1 mother. The data were collected using questionnaires with information about clinic data of BD patients, Standard Economic Classification Brazil 2008 and semi structured interview adapted by Koga. The results were analyzed by Bardins content technique. The impact in the family resulting of the relationship with BD patients was described following these aspects: work, costs with daily life, leisure, interpersonal relationship, future, resource and falling ill like expression of burden. As a result BD patients family reported that they were burdensome in the severe periods of disease. In the stable periods, only work and interpersonal aspects are continuous factors of worry and familiar suffer. Ignore the causes and the cure emerge insecurity and fear about the future. This study contributed to comprehension of that BD also burdensome the family of the patients. In addition, this people require support of health professionals to provide quality of life. The limits of this study were the short number of relatives submitted to questioners and they were come from the one source. More studies will be necessary to analyze other families and the pattern of BD illness burdensome.

En 2011, des mouvements sociaux et révolutionnaires d’une ampleur rare ont agité certains pays du nord de l’Afrique. Cela correspond à ce qu’on a appelé le printemps arabe.Le premier de ces pays touchés par ces mouvements est la Tunisie. Cette thèse porte sur la révolution tunisienne. Elle propose une analyse théorique et empirique de cette révolution.D’un point de vue théorique, ce travail se situe dans le cadre de l’analyse économique. Nous nous situons donc dans le prolongement de la littérature économique qui, à partir des années 1970, s’est intéressée aux mouvements sociaux et plus précisément les révolutions. La théorie économique a offert un autre cadre permettant d’analyser la manière dont l’action d’un petit groupe d’individus peut provoquer des bouleversements de grande envergure. L’un des objets de cette thèse est alors de proposer une synthèse de cette littérature. Nous soulignons que cette thèse revient sur les définitions de la révolution et propose une présentation qui essaye d’être exhaustive des analyses économiques des révolutions. Quatre types de modèles sont définis : la méthode décisionnelle, la théorie des jeux, la méthode d'analyse Tobit et le modèle seuil de mobilisation. Ces modèles ont parvenu à expliquer l’émergence d’un mouvement révolutionnaire mais ne prennent pas en compte la particularité de chaque pays, nous insistons en particulier sur ce point. Il n’en est pas moins vrai que, la littérature théorique sur les révolutions a précisé ce caractère unique pour chaque révolution. Autour de cette spécificité, l’idée centrale de cette thèse a été construite : quelles sont les causes de la révolution tunisienne ? En outre, la contribution principale de cette thèse est d’ordre empirique. Bien que de nombreuses recherches aient analysé de différentes manières les causes des révolutions (Données de panel, modèles économétriques), la méthode d’analyse en composantes principales (ACP) est, à notre connaissance, la première contribution dans l’analyse des révolutions et surtout la première étude de ce type appliquée à la Tunisie. Cette méthode a pu détecter trois ramifications caractérisant le 14 janvier 2011. Trois révolutions d’ordre sociologique et sociétal semblent particulièrement importantes : une révolution démographique, une révolution de l’alphabétisation et une révolution des attentes. Premièrement, la transition démographique et ses implications économiques et sociales. Deuxièmement, les inégalités et l’élargissement de la fracture sociale entre les régions. Troisièmement, la mauvaise gestion du pays suite à l’emprise de l’économie sous Ben Ali et ses conséquences catastrophique sur l’investissement et la création d’emplois. / Revolution, which embodies major turns in the course of history, has for a long time been a social study subject. With the coming of the school of public choice in the 1960's, a new economic current helped to undestand revolution. Many economists such as: James M. Buchanan (1962), Gordon Tullock (1971-1974) and John E. Romer (1985) have applied economic theory to social and political science using tools developed by microeconomy. The goal of my research paper is to highlight the contribution of economic theory in the understanding of revolution. I have first drawn a line between two approaches that have studied revolution: The sociological approach which mainly explains why do people revolt when they are faced with structural imbalances. The economic approach which uses the theory of rational choice to demonstrate how people choose to be passive when they are confronted with a revolution.

This dissertation explores the beliefs of students on the relevance (if at all) of addressing the Fifth skill, culture, in English education in a Pakistani context, with sub question that aims to answer what definitions of the Fifth skill (Tomalin, 2008) could be appropriate to English education in a Pakistani context? So far the research done on English language teaching in Pakistan and anything related to it is based on teachers’ beliefs alone, therefore it was important for me as an English Language teacher to find out what the students attitudes were towards the integration of 5th skill in the classroom. However, I did not limit the research to students’ beliefs alone; my research also includes the perception of the teachers. This is not only to give validity to the research, but also to realize any differences regarding the teachers’ beliefs on the issue in previous researches. To explore the role of 5th skill in teaching English languages in a Pakistani classroom, at the secondary level, this dissertation collected the responses elicited from both the students and the teacher through a semi-structured questionnaire and focus group discussion, and a thematic analysis was carried out. The results of this study highlight a number of issues regarding cultural acceptance, language acceptance and integrating of 5th skill in language teaching. Certain interesting contradictions regarding English culture(s) and English language and their status in Pakistani society also emerged. The findings suggest that students regarded the 5th skill as an essential source for better understanding the concepts and their functional use of English language, as it presents them with real life situations. However, where the 5th skill was seen as an important tool to enhance language competence, the students also supported that both the students’ culture as well as the culture associated with English Language be incorporated in the language class. The students saw integrating 5th skill in a language class as a means to express their ideas, values and experiences, and an opportunity to make others understand them and their point of view, and not restrict the use of Fifth skill to a one way cultural awareness stream only. The dissertation also questioned the current status of English as a second language as perceived by the students and its implications on the future of English Language teaching in Pakistan.

The idea of microfinance has burst into the area of global poverty reduction. Many comments have been made about its benefits such as; it is an alternative tool for poverty alleviation and sustainable development. Many studies have attempted to assess different facets of the impact of microfinance, especially trying to show its potential for greater financial inclusion and economic benefits using advanced rigorous quantitative approaches. Although some studies have evaluated this topic in the past there remains some significant gaps in the literature, including the impact of microfinance on other dimensions such as the social impact, education or environmental impact, the impact on happiness and subjective wellbeing of its clients has been hardly examined. This study aims to fill this gap by using rigorous quantitative methods with a rich qualitative dataset to assess the impact of microfinance on both economic and non-economic aspects, especially the happiness and psychological dimension. I Use primary data from a household survey and an ethnographic approach combining quantitative methods such as matching estimators, propensity score matching with nonparametric regression. The mixed methods were employed in order to evaluate the impact of the microfinance schemes on the improvement of borrowers’ wellbeing, household condition and local economic and environmental development. The most notable findings were that the borrowers from the savings group using group lending schemes utilised the loan for mainly entrepreneurial purposes and household spending, performed better than other groups of borrowers. This could be seen from the increase in household income and a high repayment rate. In addition, by observing the social impacts, it indicated that the group lending together with the ecotourism project generated and strengthened the social ties in the community. The group members also produced high positive psychological indicators compared to the non-member households. Easterlin’s paradox was revisited and found that not only was it income that affected happiness and wellbeing, but other factors seemed to have an influence on self-reported happiness. Those factors included health or health condition of family members which significantly influenced self-reported happiness in all models. Considering the impact of microfinance on happiness and wellbeing, it was found that clients of the group lending scheme can repay better and led to a higher level of self-reported happiness and subjective wellbeing. The ability to repay also affected a low level of stress or negative moods.

This thesis investigates the development of ultrasonic Structural Health Monitoring (SHM) systems, based on guided waves propagation, for the localization of low-velocity impacts and the detection of damage mechanisms in isotropic and anisotropic structures. For the identi- cation of the impact point, two main passive techniques were developed, an algorithm-based and an imaging-based method. The former approach is based on the dierences of the stress waves measured by a network of piezoelectric transducers surface bonded on plate-like structures. In particular, four piezoelectric sensors were used to measure the antisymmetrical A0 Lamb mode in isotropic materials, whilst six acoustic emission sensors were employed to record the wave packets in composite laminates. A joint time-frequency analysis based on the magnitude of the Continuous Wavelet Transform was used to determine the time of arrivals of the wave packets. Then, a combination of unconstrained optimization technique associated to a local Newton's iterative method was employed to solve a system of non linear equations, in order to assess the impact location coordinates and the wave group speeds. The main advantages of the proposed algorithms are that they do not require an a-priori estimation of the group velocity and the mechanical properties of the isotropic and anisotropic structures. Moreover, these algorithms proved to be very robust since they were able to converge from almost any guess point and required little computational time. In addition, this research provided a comparison between the theoretical and experimental results, showing that the impact source location and the wave velocity were predicted with reasonable accuracy. The passive imaging-based method was developed to detect in realtime the impact source in reverberant complex composite structures using only one passive sensor. This technique is based on the re- ciprocal time reversal approach, applied to a number of waveforms stored in a database containing the impulse responses of the structure. The proposed method allows achieving the optimal focalization of the acoustic emission source (impact event) as it overcomes the limitations of other ultrasonic impact localization techniques. Compared to a simple time reversal process, the robustness of this approach is experimentally demonstrated on a stiened composite plate. This thesis also extended active ultrasonic guided wave methods to the specic case of dissipative structures showing non-classical nonlinear behaviour. Indeed, an imaging method of the nonlinear signature due to impact damage in a reverberant complex anisotropic medium was developed. A novel technique called phase symmetry analysis, together with frequency modulated excitation signals, was used to characterize the third order nonlinearity of the structure by exploiting its invariant properties with the phase angle of the input waveforms. Then, a \virtual" reciprocal time reversal imaging process was employed to focus the elastic waves on the defect, by taking advantage of multiple linear scattering. Finally, the main characteristics of this technique were experimentally validated.

The purpose of this work is to illuminate some of the non-smooth phenomena found in piecewise-smooth continuous and discrete dynamical systems, which do not occur in smooth systems. We will explain how such non-smooth phenomena arise in applications which experience impact, such as impact oscillators, and a type of rotating machine, called magnetic bearing systems. The study of their dynamics and sensitivity to parameter variation gives not just insights into the critical motion found in these applications, but also into the complexity and beauty in their own right. This work comprises two parts. The first part studies a general one-dimensional discontinuous power law map which can arise from impact oscillators with a repelling wall. Parameter variation and the influence of the exponent on the existence and stability of periodic orbits is presented. In the second part we analyse two coupled oscillators that model rotating machines colliding with a circular boundary under friction. The study of the dynamics of rigid bodies impacting with and without friction is approached in two ways. On the one hand existence and stability conditions for non-impacting and impacting invariant sets are derived using local and global methods. On the other hand the analysis of parameter variation reveals new non-smooth bifurcations. Extensive numerical studies confirm these results and reveal further phenomena not attainable otherwise.

Increasing costs associated with fossil fuel generation and a recognition and acceptance of the finite nature of this resource, have partially contributed to the growing popularity of alternative energy generation technology. International environmental treaties have also forced many states, primarily developing states, to deliberately review their fuels use. Jamaica having such a challenge requires accurate information regarding the impact of integrating generation from such technologies into its existing network. However, given a lack of resources, little work has been done to gather the relevant data that is required to evaluate the impact of embedded generation. Instead the findings from networks in other jurisdictions that have different operational and technical characteristics have been utilized. Anecdotal information regarding the availability of satisfactory renewable resources and the minimal impact that certain levels of integration will have on the existing network abounds among the engineering community on Jamaica. This research reviews the electricity and energy sectors of Jamaica. It further considers the efforts made by policy makers to fulfil the energy needs through a possible mix of fossil and renewable sources. Focus is then shifted to the analysis of available wind resource data which is then modelled to represent usable wind data for electricity generation. Actual system data is then used to produce an acceptable model of the current transmission network. The operation of the network is then considered on varying generation and loading conditions both with and without the inclusion of renewable sources. A final assessment of the impact of such sources is then made based on the magnitude and location in the network. The study concludes by highlighting the benefits to be derived from this work and reviews the challenges faced while conducting the study. It also recommends ways in which improvements to the system can be realized.

"Automatic assembly machines have many cam-driven linkages that provide motion to tooling. Newer machines are typically designed to operate at higher speeds and may need to handle products with small and delicate features that must be assembled precisely every time. In order to design a good tooling mechanism linkage, the dynamic behavior of the components must be considered; this includes both the gross kinematic motion and self-induced vibration motion. Current simulations of cam-follower system dynamics correlate poorly to the actual dynamic behavior because they ignore two events common in these machines: impact and over-travel. A new dynamic model was developed with these events. From this model, an insight into proper design of systems with deliberate impact was developed through computer modeling. To attain more precise representations of these automatic assembly machines, a simplified industrial cam-follower system model was constructed in SolidWorks CAD software. A two-mass, single-degree-of-freedom dynamic model was created in Simulink, a dynamic modeling tool, and validated by comparing to the model results from the cam design program, DYNACAM. After the model was validated, a controlled impact and over-travel mechanism was designed, manufactured, and assembled to a simplified industrial cam-follower system, the Cam Dynamic Test Machine (CDTM). Then, a new three-mass, two-degree-of-freedom dynamic model was created. Once the model was simulated, it was found that the magnitude and the frequency of the vibration, in acceleration comparison, of the dynamic model matched with the experimental results fairly well. The two maximum underestimation errors, which occurred where the two bodies collided, were found to be 119 m/s2 or 45% and 41 m/s2 or 30%. With the exception of these two impacts, the simulated results predicted the output with reasonable accuracy. At the same time, the maximum simulated impact force overestimated the maximum experimental impact force by 2 lbf or 1.3%. By using this three-mass, two-DOF impact model, machine design engineers will be able to simulate and predict the behavior of the assembly machines prior to manufacturing. If the results found through the model are determined to be unsatisfactory, modifications to the design can be made and the simulation rerun until an acceptable design is obtained."

L’érosion des sentiers de moyenne montagne auvergnate est étudiée dans cette thèse à travers l’évolution morphologique de quatre secteurs présentant des stades d’érosion et des rythmes d’évolution différents, répartis dans le Massif du Sancy et la Chaîne des Puys. Notre approche méthodologique repose sur le croisement de trois jeux de données inédits collectés sur le terrain : relevés topographiques, données climatiques et cartographie du comportement des randonneurs. Les relevés topographiques fins mobilisent trois méthodes complémentaires de collecte de données (lasergrammétrie, GPS différentiel et relevés manuel). L’analyse croisée de l’ensemble de ces données nous a permis de : (1) quantifier des volumes d’érosion et de dépôt ; (2) cartographier les secteurs les plus sensibles à l’érosion ; (3) identifier une saisonnalité des processus érosifs ; (4) proposer un outil d’aide à la gestion des sentiers.Nos résultats de quantification de l’érosion des sentiers indiquent une différenciation des secteurs étudiés. Ce gradient d’érosion constaté s’explique par : le contexte climatique local qui commande la saisonnalité des processus d’érosion, la fréquentation touristique inégale et l’érodabilité du substrat. En réponse à cette érosion, nous avons observé la mise en place de divers aménagements (fils guide, fascines, murets, rigoles d’évacuation…), globalement efficaces. Néanmoins, il apparaît qu’un affinement du positionnement de ces derniers, sur la base d’une compréhension des processus érosifs sur un temps plus long, optimiserait le rôle protecteur de ces ouvrages. / In this thesis, weathering of hiking trails has been studied in the low mountain ranges of the Massif Central (Auvergne, France) through the morphological comparison of four sectors in the Massif du Sancy and the Chaîne des Puys, each one presenting different erosion stages and rhythms of evolution. Our methodological approach is based on the crossing of three unpublished field datasets: topographic data, climate data and cartography of hiker behavior. High resolution topographic data mobilized three complementary data collection methods (terrestrial laser scanning, GPS monitoring and manual monitoring). Cross-analysis of all these data allowed us to: (1) quantify erosion and depositional volumes; (2) map the weathering sensitivity of studied areas; (3) identify the seasonality of weathering processes; (4) propose an operational evaluation tool for the management of hiking trails in low mountain ranges. Weathering quantification results show a clear differentiation of the studied areas. This contrasting erosion gradient has been proved to be linked to: local bioclimatic parameters which command the seasonality of weathering processes, irregular touristic attendance and substratum durability. In response to this erosion, varied management were introduced (guideline, wattle fence, low wall, water bars ...) and globally effective. Nevertheless, it appears that a refinement of the positioning adjustments, based on an understanding of weathering processes over a longer period would optimize the protective role of these structures.

BackgroundThe rough labour market in the Philippines affects the employability. The Philippines has a unemployment rate of in-between 7-8 percent. Therefore, many Filipinos are seeking employment overseas. Today, ten percent of the population are working on the globalized market. The globalization has affected the industry, where 28 percent of the entire worlds seafarers are Filipinos. Previous researches establish that Filipinos are popular because of their knowledge in English and due to their adaptability.PurposeOur aim is to examine why a group of Filipino seafarers choose their profession. The aim is also to examine how they experience their work on international vessels, as well as if they experience any changes in life when working as international seafarers.MethodWe made a qualitative study through a ship management located in Manila in the Philippines. We used semi-structured interviews, which were applied on ten seafarers.ResultsOur respondents mention the well-paid wages as an important reason when choosing to work as a seafarer. The wages are significant in order to support family members and to have the opportunity to live a wealthy life. The seafarers are working long periods away from home that causes homesickness. A good relationship with the crew is for many seafarers important, since they are living and working together. / Program: Organisations- och personalutvecklare i samhället