A successful transition from fossil fuels to renewable energies such as wind and solar will require the implementation of high-energy-density storage technologies. Promising energy storage technologies include lithium-ion batteries, metal-air batteries, and hydrogen production via photoelectrochemical water splitting. While these technologies differ substantially in their mode of operation, they often involve transition-metal oxides as a component. Thus, fundamental materials research on metal oxides will continue to provide much needed advances in these technologies. In this thesis, the electrochemical and electrocatalytic properties of Fe- and Mn-substituted layered LiNiO₂ materials were investigated. These materials were prepared by heating mixed nitrate precursors in O₂ atmosphere at 700-850 °C for 12 h with intermediate grindings. The products were chemically delithiated with NO₂BF₄, and the delithiated samples were annealed at moderate temperatures in order to transform them to a spinel-like phase. Samples were characterized by inductively coupled plasma analysis and Rietveld refinement of the X-ray diffraction patterns, which were found to be in reasonably close agreement regarding lithium stoichiometry. Spinel-like materials were found to possess an imperfect spinel structure when heated at lower temperatures and a significant amount of NiO impurity was formed when heated to higher temperatures. This structural disorder was manifested during electrochemical cycling -- only Mn-rich compositions showed reversible capacities at a voltage of around 4.5 V. The layered materials exhibited significant capacity loss upon cycling, and this effect was magnified with increasing Fe content. These materials were further investigated as catalysts for the oxygen evolution reaction (OER). All samples containing Mn exhibited low OER activity. In addition, delithiation degraded catalyst performance and moderate temperature annealing resulted in further degradation. Because delithiation significantly increased surface area, activities were compared to the relative to BET surface area. Li₀.₉₂Ni₀.₉Fe₀.₁O₂ exhibited significantly higher catalytic activity than Li₀.₈₉Ni₀.₇Fe₀.₃O₂. This prompted testing of Li[subscript x]Ni₁₋[subscript y]Fe[subscript y]O₂ (y = 0, 0.05, 0.1, 0.2, and 0.3) samples. It was found that a Fe content of approximately 10% resulted in the highest OER activity, with decreased activities for both larger and smaller Fe contents. These results were found to be consistent with studies of Fe substituted nickel oxides and oxyhydroxides, suggesting a similar activation mechanism. / text

Philosophiae Doctor - PhD / Transition metal oxides magneli phases present crystallographic shear structure which is of great interest in multiple applications because of their wide range of valence, which is exhibited by the transition metals. The latter affect chemical and physical properties of the oxides. Amongst them we have nanostructures VO2 system of V and O components which are studied including chemical and physical reactions based on non-equilibrium thermodynamics. Due to their structural classes of corundum, rocksalt, wurtzite, spinel, perovskite, rutile, and layer structure, these oxides are generally used as catalytic materials which are prepared by common methods under mild conditions presenting distortion or defects in the case of VO2. Existence of an intermediate phase is proved using an x-ray thermodiffraction experiment providing structural information as the nanoparticles are heated. Potential application as gas sensing device has been the first time obtained due to the high surface to volume ratio, and good crystallinity, purity of the material and presence of suitable nucleating defects sites due to its n-type semiconductor behavior. In addition, annealing effect on nanostructures VO2 nanobelts shows a preferential gas reductant of Ar comparing to the N2 gas. Also, the hysteresis loop shows that there is strong size dependence to annealing treatment on our samples. This is of great interest in the need of obtaining high stable and durable material for Mott insulator transistor and Gas sensor device at room temperature.

This thesis is concerned with how the physical properties of transition metal oxides change due to chemical substitution or intercalation. Experiments using the muon-spin relaxation and rotation (μSR) techniques were carried out at the ISIS Facility (UK) and the Paul Scherrer Institute (CH). In conjunction with the μSR results, the results of heat capacity and magnetic susceptibility experiments are used to provide complementary information on the same samples. Investigations of the properties of the layered triangular lattice magnets NaNiO2 and LiNiO2 are presented. For NaNiO2, all three experimental techniques are used to provide a full survey of the thermodynamic and magnetic properties of this compound. For LiNiO2, μSR studies of notionally stoichiometric and Mg-doped samples were carried out. These showed that Mg doping causes a significant change in the magnetic dynamics of the material, but neither sample exhibits long-range magnetic order. The magnetic ordering of the extensively studied perovskite compounds LaTiO3 and YTiO3 is investigated using μSR. The results were in agreement with previous neutron diffraction studies of the two compounds, but clarified the orientation of the magnetic moments in LaTiO3. It was also possible to make a detailed comparison between the μSR results and those of dipole field calculations of the magnetic field at possible muon stopping sites, allowing these to be deduced and compared with results in other well characterized transition metal oxides. The two titanium chain compounds NaTiSi2O6 and TiOCl exhibit spin gap formation at unusually high temperatures due to unconventional dimerization mechanisms. A model allowing the comparison of X-ray diffraction data, dimerization, and the magnitude of the spin gap is proposed. This is tested against both magnetic susceptibility and μSR data for both compounds. For NaTiSi2O6 both experimental techniques are in reasonable agreement, whereas in TiOCl the results are conclusively different. The origin of this disparity in TiOCl is explored. The intercalation of organic chain molecules into Bi based high-temperature superconductors has previously been demonstrated to extend the interlayer spacing by a factor of up to three without changing the superconducting transition temperature. μSR is used to investigate the London penetration depth, as a function of interlayer spacing, of two series of such samples. The results show a simple trend corresponding to a constant density of superconducting electron pairs in each layer. The consequences of this result are discussed in the context of previously identified scaling relations between superconducting parameters. Results of experiments excluding the possibility of magnetic order and muon-organic radical formation in these samples are presented, as well a preliminary study of the field distributions in a mosaic of intercalated crystallites.

Metal-insulator transition is one of the most important properties observed in certain materials which has been studied widely using a wide range of experimental techniques as well as theoretical models. This kind of a transition, observed in several systems, can take place by tuning several parameters such as pressure, temperature or the composition itself. In this thesis we study a few selected transition metal oxide bronzes exhibiting such phenomenon, each of which has a different cause for undergoing the transition. In Chapter 1, we discuss briefly several mechanisms and models that have been used to understand metal-insulator transitions. We also briefly discuss the role of disorder, electron-electron correlations or both to understand the different ways in which such transitions can occur. In Chapter 2, we describe the different experimental as well as theoretical techniques that have been used in this thesis. In Chapter 3, we study the fermi-edge of the NaxWO3 systems, as a function of x, to understand the origin of the metal-insulator transition occurring in this series of compounds. The system undergoes a metal-insulator transition at the critical composition xc=0.25, below which it is found to be insulating. At the lowest temperature, the very low x compounds behave as disordered and correlated materials. Above the transition composition, the compounds behave as disordered and correlated metals. In the insulating regime, close to the critical composition, we find that the system behaves in a way that cannot be described by any known theories for metals or insulators. We have also done a systematic analysis of the Fermi-edge data for the insulating samples as a function of temperature and we find that they cannot be described by any of the known theories for solid-state systems. Further development is necessary in the theoretical side to understand and interpret our data. In Chapter 4, we study the angle-resolved photoemission data for the highly metallic sodium tungsten bronze Na0.8WO3. We have synthesized the single-crystals by high-temperature electrochemical synthesis and we have performed angle-resolved photoemission experiments to understand the band structure of this system. The experimental results have been supported by theoretical calculations. We find that the rigid band model is valid in describing the electronic structure in these systems. We also find the existence of electron-like pockets along certain symmetry directions. Further, photon energy dependent studies on the x=0.8 sample suggest that there is a difference in the surface with the bulk of the sample. The bulk is perfectly periodic and ordered, whereas the surface shows a distortion due to the rotation or deformation of the WO6 octahedra. In Chapter 5, we have studied the electronic structure of the low dimensional molybdenum oxide La2Mo2O7, which is expected to have a charge density wave(CDW)driven metal-insulator transition around 125K. We indeed observed the presence of CDWs in this system, which was observed in the angle-resolved photoemission spectra as back-folding of bands below the transition temperature. We have also studied the temperature evolution of the bands close to the Fermi level and we see a gradually weakening and finally disappearance of the back-folded bands close to and above the transition temperature. We have studied the angle-integrated spectra of this system from which we conclude that La2Mo2O7 is a CDW non-Fermi liquid system. We have also evaluated the total and partial density of states in this system using Vienna ab-initio simulation package. We find the results consistent with our experimental findings. In Chapter 6, we study the metal-insulator transition in another low-dimensional molybdenum oxide KMo4O6, which is expected to show a metal-insulator transition around 120K due to the formation of spin-density waves. We observed back-folding of bands with lower intensities at low temperature, suggesting the formation of spin density waves in the system. The angle-integrated spectra suggested that the system is a non-CDW non-Fermi liquid system. We have also evaluated the density of states and the results are in agreement with our experimental findings. In conclusion we have investigated the electronic structure of different classes of systems and we have given clue to the origin of the metal-insulator transition in these systems.

京都大学 / 0048 / 新制・論文博士 / 博士(工学) / 乙第13240号 / 論工博第4178号 / 新制||工||1720(附属図書館) / (主査)教授 木本 恒暢, 教授 藤田 静雄, 教授 山田 啓文 / 学位規則第4条第2項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

In this dissertation, we utilized a wide range of complementary synchrotron-based X-ray spectroscopic and scattering techniques, notably X-ray absorption spectroscopy (XAS), hard X-ray photoelectron spectroscopy (HAXPES), standing-wave X-ray photoelectron spectroscopy (SW-XPS), and X-ray resonant magnetic reflectometry (XRMR), to understand and control the phenomenon of emergent interfacial ferromagnetism in strongly-correlated oxide heterostructures. This field holds great promise for the development of next-generation spintronic devices. In the heterostructures we investigated, neither of the parent oxide layers exhibits inherent ferromagnetism. Yet, when these layers are combined in an epitaxial film stack, charge-transfer phenomena give rise to an emergent ferromagnetic state at the interface. Throughout my graduate studies, I focused on studying such charge-transfer phenomena as the driving force for stabilizing interfacial ferromagnetism. This dissertation is structured around two main projects. The first project delves into the intriguing possibility of tuning the emergent interfacial ferromagnetism. More specifically, we investigated the mechanisms for suppressing interfacial charge transfer to gain control over and manipulate this magnetic phenomenon. In our second project, we explored a different facet of interfacial ferromagnetism, focusing on the origins of the imbalance in the magnitudes of the magnetic moment between the top and bottom interfaces in the same layer. Our investigation aimed to uncover the possible causes of this imbalance, ultimately leading us to scrutinize the role of defect states in this magnetic asymmetry. In the first part of this dissertation, we investigated the thickness-dependent metal-insulator transition within LaNiO3 and how it impacts the electronic and magnetic states at the interface between LaNiO3 and CaMnO3. We present a direct observation of a reduced effective valence state in the interfacial Mn cations. This reduction is most pronounced in the metallic LaNiO3/CaMnO3 superlattice, where the above-critical LaNiO3 thickness of 6-unit cells triggers this phenomenon, facilitated by the charge transfer of the itinerant Ni 3d eg electrons into the interfacial CaMnO3 layer. In contrast, when we examine the insulating superlattice with a LaNiO3 thickness below the critical value (2-unit cells), we observe a homogeneous effective valence state of Mn throughout the CaMnO3 layers. This homogeneity is attributed to the suppression of charge transfer across the interface. The second part of this dissertation delves deeply into the complexities of interfacial magnetism within the CaMnO3/CaRuO3 superlattices. Our experimental investigation unveiled an unexpected asymmetry in the strength of magnetism at these interfaces. Our findings suggest that within the superlattice CaMnO3/CaRuO3, the lower interface (CaRuO3/CaMnO3) exhibits a weaker magnetic moment when compared to the upper interface (CaMnO3/CaRuO3). This observation, supported by XRMR and XAS experimental data, was further clarified by first-principles density functional theory (DFT) calculations. Our calculations suggest that the observed magnetic asymmetry may be linked to the presence of oxygen vacancies at the interfaces. Our study significantly contributes to our understanding of interfacial ferromagnetism, potentially paving the way for controlling and manipulating this emergent property. This may be achieved by utilizing engineered defect states, offering exciting prospects for applications in the field of spintronics devices. / Physics

MnO2 continues to gain traction in the research and development of advanced supercapacitor materials due to its arsenal of advantages, such as high capacitance, low cost, natural abundance, and environmental benignity. However, its low conductivity has hindered its adoption into real-life applications. Compositing MnO2 with conductive additives has proved to be a promising route for the improvement of its power-energy characteristics. Four novel colloidal techniques were developed for the synthesis of MnO2-CNT composites with enhanced performance at high active mass loading. One strategy utilized a Schiff-based linkage of dispersants such as 3,4-Dihydroxybenzaldehyde (DHB) and Toluidine Blue O (TDB) to effectively mix and disperse MnO2 and CNT. Secondly, a co-dispersion technique was also investigated using Gallocyanine to improve dispersion and mixing of MnO2 and MWCNT. Third, a novel liquid-liquid extraction technique opened new avenues in agglomerate-free processing of individual components, which allowed enhanced electrode performance. Lastly, a morphology-modification strategy was also undertaken by synthesizing MnO2 nanorods with the use of advanced organic dispersants to control the aspect ratio and composite nanorods with MWCNT. The second major material investigated was polypyrrole (PPy), a polymer material with high conductivity, ease of synthesis, low-cost, and non-toxicity. However, its low cyclic stability was prevented it from being applied for real-world applications. Certain anionic and aromatic dopants have shown to improve the conductivity and cyclic stability. Therefore, one of the investigations in this work attempted to improve the performance of PPy-CNT composites by use of a novel anionic dopant, Sunset Yellow (SY). For all investigations electrodes with high mass loadings were produced to achieve high areal capacitance, thus ensuring the practicality of the techniques / Thesis / Master of Applied Science (MASc) / Supercapacitors (SCs) and batteries are both electrochemical energy storage devices. While batteries excel at storing energy in high volumes, supercapacitors excel in charging (and discharging) at extremely high rates. It is desirable to obtain the best of both worlds in a single device; high energy volume and fast charging speeds. Although such a feat is not out of the realm of theoretical possibility, current projections forecast supercapacitors to compliment battery technologies instead of replacing them. Nonetheless, constant progression in the field of SCs is needed to sustain and proliferate their adoption into emerging markets. Therefore, the aim of this research was to assist in the endeavours to improve current SC technologies from a materials science standpoint.

再生可能エネルギーの大量導入に向けて、電力需給の安定化を目的として蓄電池を用いる電力貯蔵技術に注目が集まっている。現状のリチウムイオン電池(LIB)がベースの先進LIBは250Wh/kgの高エネルギー密度を有し、自動車のみならず電力貯蔵用途としても普及が期待されている。本研究では先進LIB正極材料として期待されるリチウム過剰系正極と高ニッケル三元系正極について容量低下などの劣化要因を明確にして、それら課題に対して正極粒子への酸化物修飾による解決を検討した。 / The development of energy storage technologies using batteries has attracted much attention to introduce the renewable energy. If we can achieve 250 Wh kg-1 with the advanced LIBs based on the principle of LIB, we can lower the cost of the total energy storage systems while ensuring the safety, and hence the advanced LIBs will accelerate the world-wide spread of large-scale power storage systems. In this thesis, the author focused surface modification of lithium-rich layered ternary transition metal oxide and high-nickel layered ternary transition metal oxide cathode particles with oxides as mitigation methods for capacity fading. / 博士(工学) / Doctor of Philosophy in Engineering / 同志社大学 / Doshisha University

The transition-metal oxides (TMOs) are a material class host to a number of intriguing and potentially technologically useful phenomena as a result of many-body correlation effects, from superconductivity, magnetic and orbital ordering, to ferroelectricity and metal-insulator transitions. Here, materials with similar structures and seemingly equivalent electronic configuration often exhibit wildly different properties as a result of strong competition between different ground states from the many degrees of freedom, whose balance can be further tuned through the use of pressure, doping, magnetic fields or temperature. To investigate these materials, we make use of photoelectron spectroscopy (PES), probing elementary excitations possible in the material and thus providing linked information both about the ground state and possible excited states, closely related to the physical properties of a material such as its response to external fields. Angle-resolved PES (ARPES) provides additional momentum information and as a result, it is uniquely suited to investigate the character of the electronic structure of solids as it resolves the dispersion, meaningful in the independent-electron view where crystal momentum is a well-defined quantum number, but which can retain validity even in strongly correlated systems through the concept of quasiparticles. While ARPES is a well-established technique, it is rarely used in the soft X-ray regime (SX-ARPES) due to significant experimental challenges posed. However, the higher energies in SX-ARPES allow it to be significantly more bulk-sensitive, an extremely important fact since the properties of the bulk material and its surface are often extremely, or worse, subtly different. Critically, this permits measurements on single crystals of TMOs, whose surfaces may show roughness or reconstruction, for example as a result of a polar surface compensation, but whose bulk properties are well-defined in contrast to thin films which are additionally subject to substrate effects. We demonstrate on three rather different perovskite oxides, a three-dimensional class of TMOs, that is worthwhile to overcome these issues since it provides access to the true momentum-resolved bulk electronic properties of materials and allows filling noticeable gaps in literature of k-resolved electronic structure measurements for this class of compounds stemming from the impossibility of such measurements at lower energy. A commonality between the materials studied in this thesis is the absence of a strong electronic symmetry-breaking order, such as local-moment antiferromagnetism or charge ordering, that could suppress the existence of sufficiently long-lived quasiparticles to observe dispersion (or equivalently prevent a mobile photo-hole). We first establish that SX-ARPES is indeed capable and suited to measure the bulk-representative electronic structure by measurements on the perfect cubic d1 perovskite ReO3. We present the first k-resolved electronic structure for this material which is rather well explained by band structure, especially close to the Fermi level. In particular, we show and quantify the impact of the significant spin-orbit coupling on the Fermi surface and bands. However, the oxygen bands are less well reproduced by calculations and are correctable by use of hybrid functionals, taken as a sign of spurious self-interaction effects - likely due to the large extent and density differences between delocalised Re 5d and more localised O 2p. We also show that there are signs of some hitherto unknown distortion in ReO3. We then turn to LaNiO3, a metallic oxide in a family of formally d7 rare-earth nickelates which otherwise all undergo metal-insulator and antiferromagnetic (AFM) transitions as well as oxygen bond disproportionation, with a strong competition between these ground states and possible exotic resulting states in the phase diagram. We are able to resolve the dispersion of the eg quasiparticle spectrum along high symmetry cuts of this material as well as its Fermi surface, the latter of which is accurately reproduced by band theory calculations. We investigate the influence of the rhombohedral distortion present in the material through unfolding methods to better compare their influence to measurement, and show how significantly it affects the dispersion, confirming again the importance of single crystals. Its effects are shown to be similar to correlation-induced mass enhancement and their effects are untangled with the help of first DFT+U and later rhombohedral multi-band dynamical mean-field theory (DMFT) calculations. Local correlation effects prove to be the dominant influence on the spectrum, although certain k-dependent mismatches remain, pointing to a possible simultaneous importance of non-local mechanisms. Finally, on the d6 system LaCoO3 that is close to a spin-state transition, we show that this method can also be applied to insulating oxides. Absent a Fermi surface, we naturally concentrate more on the full valence band, where we show that the observed dispersion is well-described by mean-field band methods in the low-spin (LS) regime of LaCoO3 provided that static energy corrections of DFT+U are accounted for (which show a good match to local LS many-body configuration interaction calculations), thus providing k-resolved evidence that one may effectively consider LS LaCoO3 a band insulator, despite possibly strong correlations. We further unveil clear evidence of crystal periodicity doubling by observation of a backfolded oxygen band, and show evidence of a significant asymmetry in the k-resolved lineshape in the valence band and lastly we take a look at the spin state of Co at the surface, which, contrary to prior results, appears to be the same as in the bulk, but which we show to be complicated by significant orbital-shape matrix element effects.

Ca2RuO4 is a structurally-driven Mott insulator with a metal-insulator (MI) transition at TMI = 357K, followed by a well-separated antiferromagnetic order at TN = 110 K. Slightly substituting Ru with a 3d transition metal ion M effectively shifts TMI and induces exotic magnetic behavior below TN. Moreover, M doping for Ru produces negative thermal expansion in Ca2Ru1-xMxO4 (M = Cr, Mn, Fe or Cu); the lattice volume expands on cooling with a total volume expansion ratio reaching as high as 1%. The onset of the negative thermal expansion closely tracks TMI and TN, sharply contrasting classic negative thermal expansion that shows no relevance to electronic properties. In addition, the observed negative thermal expansion occurs near room temperature and extends over a wide temperature interval. These findings underscores new physics driven by a complex interplay between orbital, spin and lattice degrees of freedom. These materials constitute a new class of Negative Thermal Expansion (NTE) materials with novel electronic and magnetic functions.