O objetivo do presente trabalho foi a avaliação do envelhecimento de um tubo de raios X com anodo de tungstênio utilizado para aplicações de radiodiagnóstico, por meio de aplicação de cargas de acordo com distribuições de cargas de trabalho da realidade brasileira e avaliações periódicas de grandezas associadas à qualidade de radiação produzida. Para o propósito deste trabalho, um sistema clínico com retificação monofásica de onda completa foi utilizado. Para avaliação em longo prazo das características do tubo de raios X relacionadas à carga de trabalho foi necessária a medição de parâmetros que pudessem representar de forma quantitativa o envelhecimento do tubo de raios X, estando estes relacionados principalmente ao desgaste do anodo. Esta medição indireta do envelhecimento do tubo levou a escolha de quatro parâmetros, alguns deles normalmente empregados na prática de controle de qualidade de equipamentos de radiologia diagnóstica: primeira e segunda camada semi-redutora (CSR), dimensões dos pontos focais, medida não invasiva do Potencial de Pico Prático e espectrometria de raios X. Estes parâmetros foram medidos inicialmente e após cada aplicação de carga pertinente. Para garantir a confiabilidade dos resultados, condições de reprodutibilidade foram estabelecidas para cada parâmetro de avaliação. As incertezas envolvidas em todos os processos de medição foram calculadas para avaliação da real contribuição dos efeitos do envelhecimento do tubo de raios X nos parâmetros não invasivos. Dentre os parâmetros avaliados, os que mostraram maior sensibilidade aos efeitos da aplicação de carga em longo prazo foram as energias médias obtidas por meio de espectrometria de raios X e as camadas semi-redutoras. Um modelo relacionado a estes parâmetros foi aplicado e estimativas da taxa de envelhecimento do tubo de raios X para diferentes tensões de aceleração e correntes anódicas foram obtidas. / The objective of the present work was the evaluation of an x ray tube aging with an anode made of tungsten, used in radio diagnostic. Workloads were applied, in accordance with Brazilian workload distribution, and periodic measurements of quantities related to the radiation quality of the beam were performed. For the purpose of this work, a single phase, full bridge clinical system was employed. For the long term x ray tube characteristics evaluation related to the applied workload, it was necessary to measure parameters that could quantitatively represent the tube aging, with special attention to the anode roughening. For the indirect measurement of tube aging, four parameters were chosen, some of them normally applied in x ray diagnostic quality control: first and second half value layers (HVL), focal spot dimensions, non invasive measurement of Practical Peak Voltage (PPV) and x ray spectroscopy. These parameters were measured before any workload and after each workload intervals. To assure confidence of the results reproducibility conditions were stated to each evaluated parameter. The uncertainties involved in all measurement processes were calculated to evaluate the real contributions of x ray tube aging effects on non invasive parameters. Within all evaluated parameters, the most sensitive to long term workload were the mean energy obtained from spectroscopy and half value layers. A model related to these parameters was applied and estimates of x ray tube aging rate for different acceleration voltages and anodic currents were calculated.

Um reator anaeróbio tratando esgoto sintético de baixa concentração de matéria orgânica (500 mgDQO/L-1) e enriquecido com diferentes concentrações de sulfato (razões DQO/[SO4-2] de 1,34, 0,67 e 0,34) foi submetido à diferentes estratégias de alimentação (batelada e batelada alimentada de 3 h e de 6 h). O reator operou com capacidade de 4,0 L e tratou por ciclo de 8 h um volume de 2,0 L de esgoto sintético. Desta forma, executaram-se 9 condições diferentes que foram submetidas à análise com o objetivo de investigar a influência do tempo de alimentação e da razão DQO/[SO4-2] no desempenho do sistema. A temperatura do reator foi constante em 30 ± 1°C e a agitação mecânica foi fixada em 400 rpm. Como suporte para a imobilização da biomassa foram utilizados cubos de espuma de poliuretano. Os resultados obtidos demonstraram que a operação em batelada alimentada de 3 h com uma razão DQO/[SO4-2] de 0,34 apresentou as melhores condições para a remoção de matéria orgânica (89%). Quanto à remoção de sulfato observou-se uma estagnação neste mesmo modo de operação ao aumentar a concentração de sulfato no afluente, enquanto que na operação com alimentação em batelada alimentada de 6 h, a carga de sulfato removida (CSR) cresceu linearmente. Assim, a maior carga de sulfato removida foi registrada durante o ensaio em batelada alimentada de 6 h com uma razão DQO/[SO4-2] de 0,34, no qual foram removidos 0,55 g SO4-2(L.d). Com uma razão DQO/[SO4-2] de 1,34 e um tempo de enchimento de 6 h, o reator apresentou o melhor desempenho em termos de eficiência de remoção de sulfato (71%). Em todos os ensaios o reator apresentou estabilidade, com uma produção alta de alcalinidade a bicarbonato e a concentração de ácidos voláteis se manteve em níveis adequados. / An anaerobic sequencing batch reactor treating synthetic low strength wastewater (500 mgCOD/L-1) enriched with different sulfate concentrations (COD/[SO42] ratios of 1,34, 0,67 and 0,34) was operated at different fill times (batch mode and sequencing batch mode of 3 h and 6 h fill time). The reactor operated with a capacity of 4,0 L and treated per 8-h cycle 2,0 L of synthetic wastewater. Thus, 9 different configurations resulted from this configuration and were submitted under analyses with the objective to investigate the influence of each of those parameters on the performance of the system. The reactor was operated at a constant temperature of 30 ± 1°C and an mechanical agitation rate of 400 rpm. Cubic particles of polyurethane were used as support material for anaerobic biomass immobilization. The results showed that operating the reactor with a fill time of 3 h and a COD/[4-2] ratio of 0,34 was the most eficient strategy for COD removal (89%). During the same operation mode (3 h fill time) sulfate removal seemed to suffer stagnation due to the increasing sulfite concentation in the reactor, whereas with a fill time of 6 h the sulfate load removal increased linerally with increasing sulfate load. So the biggest removal, in terms of volumetric sulfate load, was obtained operating the reactor in sequencing batch mode with a fill time of 6 h and a COD/[4-2] ratio of 0,34. During this test the reactor removed 0,55 gSO4-2/(L.d) of 2,29 gSO4-2/(L.d) applied on the system. Operating at a COD/[SO4-2] ratio of 1,34 and a fill time of 6 h the reactor obtained the best results in terms of sulfate removal efficiency, with 71% of the sulfate removed from the system. In the entire period of analisis the reactor showed stability with a suficient production of alkalinity to maintain the concentration of volatil acids in adequate levels.

O presente projeto avaliou um reator anaeróbio operado em batelada e batelada alimentada seqüenciais (ASBR), em ciclos de 8 horas, utilizando biomassa granulada e agitação mecânica em um draft-tube, alimentado com água residuária sintética (500 mgDQO/L), contendo sulfato em diferentes relações DQO/[\'SO IND.4\' POT.2-\']. Em todos os ensaios o reator apresentou uma operação estável, produzindo alcalinidade e com concentração de ácidos voláteis totais em níveis adequados. Para os tempos de alimentação de 10 min, 3 h e 6 h, respectivamente, as eficiências de remoção de sulfato foram de 30, 72 e 72% nas operações nas quais o reator foi alimentado com uma relação DQO/[\'SO IND.4\'POT.2-\'] de 1,34. Nos ensaios nos quais o reator foi alimentado na relação DQO/[\'SO IND.4\'POT. 2-\'] de 0,67, as eficiências para a redução de sulfato foram de 25, 58 e 55%, respectivamente. Na operação com relação DQO/[\'SO IND.4\'POT.2-\'] de 0,34, as eficiências para redução de sulfato foram de 23, 37 e 27%, respectivamente. Desta maneira, pode-se concluir que as operações em batelada alimentada favoreceram a remoção de sulfato, enquanto foi observado que nas operações em batelada a remoção de matéria orgânica atingiu melhores eficiências. / This present work evaluate an anaerobic sequencing batch reactor (ASBR), fed in batch and fed-batch, and cycles of 8 hours, using granulated biomass and mechanical stirring in a draft-tube, fed with synthetic wastewater (500 mgCOD/L), enriched with sulfate in some COD/[\'SO IND.4\'POT.2-\'] relations. In all operations the reactor showed a stable operation, producing alkalinity and maintaining the volatile acids in adequate levels. Considering the fed periods of 10 min, 3 h and 6 h, respectively, the removal efficiencies of the sulfate was 30, 72 e 72%, in the operations when the reactor was fed with a COD/[\'SO IND.4\'POT.2-\'] relation of 1,34. In the essays when the reactor was fed in COD/[\'SO IND.4\'POT.2-\'] relation of 0,67, the efficiencies of the sulfate reduction was 25, 58 e 55%, respectively. When the reactor was operated with COD/[\'SO IND.4\'POT.2-\'] relation of 0,34, the efficiencies of sulfate reduction 23, 37 e 27%, respectively. Thus, is possible to conclude that the operations in fed-batch increased the efficiency of sulfate removal, at what time was observed that in batch operations the organic matter removal attained improved efficiencies.

La relation entre les propriétés viscoélastiques complexes de liquides polymères et leur structure microscopique et la dynamique est une question clé dans la science des matériaux et de la biophysique. Les théories modernes de la dynamique des polymères et la rhéologie décrivent les aspects universels du comportement viscoélastique sur la base de l'idée que les enchevêtrements moléculaires confinent filaments individuels à une dimension, la dynamique diffusifs (reptation) dans le tube-comme les régions dans l'espace. Alors que le modèle de tube est validé par son succès, ses éléments constitutifs (les statistiques et la dynamique de l'axe du tube ou des chemins primitifs et de l'confinement "cage" de chaînes voisines) ne sont pas directement observables. (1) Nous présentons un vaste ensemble de résultats de simulation pour la relaxation des contraintes à l'équilibre et l'étape-tendues perles printemps polymères fondus (En collaboration avec: C. Svaneborg et GS Grest). Les données nous permettent d'explorer la dynamique de la chaîne et le module de la relaxation de cisaillement dans le régime plateau pour les chaînes avec Z~40 enchevêtrements et dans le régime de relaxation terminale pour Z~10. Nous avons effectué des tests sans paramètres de plusieurs modèles différents de tubes à l'aide de (Rouse) la mobilité connue des chaînes unentangled et la longueur d'enchevêtrement de fusion déterminé par l'analyse du chemin primitif de l'état microscopique topologique de nos systèmes. (2) Nous présentons une compréhension complète pour la détente des empêtré polymère linéaire fond que les liens de la dynamique et la théorie de Rouse tube par une interprétation dynamique qui s’appellel’analyse du chemin primitive. La chaîne primitive, qui est la moyenne d'ensemble des conformations de la chaîne, se rétrécit strictement d’après la dynamique Rouse jusqu'à ce qu'il renconte les obstacles formés par d'autres chaînes primitives. Le temps d'arrêt de la diminution peut être déterminée par l'argument que la zone balayée par la chaîne primitive sur une longueur de propagation de tension qui est égale à la taille du maille de filet du travail formé par les chaînes de primitives. Le processus physique avant l'heure d'arrêt est assez présenté par l'analyse du chemin primitif. Après le temps d'arrêt, les longueurs primitives seront rétrécites par la reptation et la fluctuation de la longueur de contour .Cette procedure peut être décrite comme la modèle du tube, par exemple, Likhtman-McLeish (LM) la théorie. (3) Nous constatons que la théorie sous-estime la relaxation LM module de cisaillement dû à un double comptage de l'effet de courte longueur d'onde (p> Z) dans les modes partie de relaxation de Rouse et en fonction de la trompe de mémoire μ (t). LM extrapolé μ (t) à la limite du continuum, ce qui entraîne une décroissance sur des échelles de temps inférieur au temps de l'intrication, où le mouvement de la chaîne primitive devrait être négligeable. Pour corriger cela, nous avons retiré de la partie de fluctuation contour longueur de μ (t) la contribution des modes avec un temps de relaxation plus court que le temps d'enchevêtrement. Nous trouvons un excellent accord entre nos données de simulation et la théorie LM modifiée en utilisant l'approximation reptation double pour la libération de contrainte, ce qui démonte que l'analyse du chemin primitif de la structure microscopique apporte du modèle de tube avec une puissance prédictive des processus dynamiques. L'utilisation de systèmes plus complexes pour le traitement de la libération de contrainte devrait conduire à un accord encore mieux. / The relation between the complex viscoelastic properties of polymer liquids and their microscopic structure and dynamics is a key issue in materials science and biophysics. Modern theories of polymer dynamics and rheology describe the universal aspects of the viscoelastic behavior based on the idea that molecular entanglements confine individual filaments to a one-dimensional, diffusive dynamics (reptation) in tube-like regions in space. While the tube model is validated through its success, its constituting elements (the statistics and dynamics of the tube axis or primitive paths and of the confining "cage" of neighboring chains) are not directly observable. (1) We present an extensive set of simulation results for the stress relaxation in equilibrium and step-strained bead-spring polymer melts (In cooperation with: C. Svaneborg and G. S. Grest). The data allow us to explore the chain dynamics and the shear relaxation modulus into the plateau regime for chains with Z~40 entanglements and into the terminal relaxation regime for Z~10. We have performed parameter-free tests of several different tube models by using the known (Rouse) mobility of unentangled chains and the melt entanglement length determined via the primitive path analysis of the microscopic topological state of our systems. (2) We present a full understanding for relaxation of entangled linear polymer melts that links the Rouse dynamics and tube theory via a dynamic interpretation of the so called primitive path analysis. The primitive chain, which is the ensemble average of the chain conformations, shrinks strictly following the Rouse dynamic until it encounters the obstacles formed by other primitive chains. The stop time of the shrinking can be determined by the argument that the area swept by the primitive chain over a tension propagation length is equal to the mesh size of the net work formed by the primitive chains. The physical process before the stop time is fairly presented by primitive path analysis. After the stop time, the primitive length shrinks via reptation and contour length fluctuation, which is well described by the tube theory, e.g. Likhtman-McLeish (LM) theory. (3) We find that the LM theory underestimates the shear relaxation modulus due to a double-counting of the effect of short-wavelength (p>Z) modes in Rouse relaxation part and in tube memory function μ(t). LM extrapolated μ(t) to the continuum limit, resulting a decay on time scales smaller than the entanglement time, where the motion of the primitive chain should be negligible. To correct this, we have removed from the contour length fluctuation part of μ(t) the contribution of modes with a relaxation time shorter than entanglement time. We find excellent agreement between our simulation data and the modified LM theory using the double reptation approximation for constraint release, which demonstrates that the primitive path analysis of the microscopic structure endows the tube model with predictive power for dynamical processes. The use of more elaborate schemes for treating constraint release should lead to even better agreement.

Lorsqu’on découpe un feuillard à l’aide d’un outil, ou lorsqu’on découpe un tube selon son axe, au fur et à mesure que l’on propage la fissure qui traduit la découpe il arrive que des ondulations de flambage perturbent les deux bords libres générés par la propagation de la fissure. Cette étude vise à analyser les origines de ces ondulations. Nous avons mené une campagne expérimentale, dans laquelle des tubes en acier inox avec différentes géométries (rayon/épaisseur) sont « découpés » selon une génératrice. Une instrumentation adéquate, couplant des mesures ponctuelles, à l’aide de jauges de déformation, et une méthode champ par corrélation d’image, nous a permis de correctement mettre en exergue la phénoménologie, en particulier les cinématiques induites à l’échelle géométrique de la fissure (front de fissure) ainsi qu’à l’échelle du tube, avec les longueurs d’onde de flambage observées à l’aval de la fissure. La modélisation numérique menée en non linéaire géométrique (flambage), matériau (déchirure ductile), et conditions aux limites (contact) est aussi abordée à l’aide du code de calcul Abaqus/Standard. Pour la gestion de la propagation de la fissure, deux modèles de rupture sont proposés. Le premier modèle dit zone cohésive est développé et implanté dans le code Abaqus via la subroutine UEL. Pour la deuxième modélisation, nous avons utilisé le modèle dit « d’endommagement ductile » du code Abaqus. La modélisation via des éléments massifs ou des éléments coques volumiques ainsi que l’utilisation de ces modèles de rupture permettent de corroborer les observations expérimentales. Ces travaux montrent que l’augmentation de la charge inhérente au déplacement de l’outil de « découpe », induit une extension dans la direction circonférentielle et donc une striction dans la direction radiale amenant finalement la rupture. Lors de la rupture, un « sillage plastique » apparait, relativement large, près et parallèle aux bords de la fissure. « Confiné » par les autres parties du tube qui restent élastiques, des contraintes de compression axiale résiduelles apparaissent dans ce sillage plastique, à l’aval de la fissure, leur intensité est suffisante pour produire les ondulations des bords libres qui traduisent un flambage local. Les contraintes résiduelles liées à l’opération de découpe induisent donc le flambage. / When one uses a tool to cut a sheet metal, or a tube according to his axis, as one propagates the crack which translates cutting it arrives that undulations of buckling disturb the two free edges generated by the propagation of the crack. This study aims at analyzing the origins of this behavior. We conducted an experimental campaign, in which stainless steel tubes with various geometries (radius/thickness) are « cut out » according to a generator. An adequate instrumentation, coupling of specific measurements, using strain gauges, and a field method, by digital image correlation, allowed us accurately to put forward phenomenology, in particular the kinematics at the scale of the crack (ahead of crack tip) and at the level of tube, with the wavelengths of buckling observed at the downstream of the crack tip. The numerical modeling taking into account nonlinearities of material (ductile tear), geometry (buckling) and boundary conditions (contact) is also approached using the code Abaqus/Standard. For the management of the crack propagation, two rupture models are proposed. The first model called cohesive zone is developed and implemented in the Abaqus code via the user routine UEL. For the second modeling, we used the model called “ductile damage model” in the Abaqus code. Modeling via solid elements or shell continuum elements as well as the use of these rupture models make it possible to corroborate the experimental observations. These studies show that the increase of the load inherent in the displacement of the tool of « cutting » induced a circumferential extension of the tube that leads to a local necking in the radial direction bringing the rupture finally. During the failure, a “plastic wake” appears, relatively wide, close and parallel to crack lips. Constrained by other parts of the tube which remain elastic, sufficient axial residual compressive stresses produced in this plastic wake produce the undulations which represents a local buckling. The residual stresses related to the operation of cutting thus induce buckling.

Le tube à onde progressive (TOP) est un dispositif où un faisceau d’électrons se déplaçant sur l’axe d’une hélice interagit avec les ondes électromagnétiques propagées par cette hélice. Il est le siège de nombreuses instabilités : des oscillations (génération d’ondes hyperfréquences parasites), mais aussi des instabilités du faisceau qui ont pour conséquence une dissipation parasite due à l'interception du faisceau par l'hélice. L’objectif de cette thèse est de développer une formulation hamiltonienne au problème permettant des modèles approchés plus compacts, plus précis et plus complets. Après l'avoir exposée, nous présentons un schéma numérique contenant notre modèle discret pour la simulation du TOP. Ce modèle discret a été mis au point pour tenir compte des conditions d'adaptation et de changements de géométrie. Le couplage avec les électrons met en jeu des champs de base simples, et le modèle tient compte de la charge d'espace. Différentes méthodes d'intégration numérique sont développées, dont nous comparons l'efficacité. Nous comparons ce modèle discret avec divers modèles d'amplification des ondes à froid, dont le modèle actuellement utilisé chez Thales pour la conception des tubes ({texttt{MVTRAD}}). Nous montrons aussi que les modèles d'amplification des ondes à froid à deux ou trois dimensions comme {texttt{MVTRAD}} ou {texttt{BWIS}} (prenant en compte les ondes inverses) ne respectent pas nécessairement l'équation de Maxwell-Faraday, contrairement au nôtre. Enfin, nous comparons notre modèle discret de circuit et le modèle d'amplification des ondes à froid dans le cas d'un faisceau linéaire. / A traveling-wave tube (TWT) is a device where an electron beam traveling along the axis of a helix interacts with the electromagnetic waves propagated by this helix. It is sensitive to many instabilities : oscillators (generating noise microwave), but also beam instabilities that generate a noise dissipation due to the interception of the beam by the helix. The aim of this thesis is to find a Hamiltonian formulation of the problem to allow more compact, more accurate and more complete approximate models. Having found one, we start to develop a numerical scheme containing our discrete model for the simulation of TOP. This discrete model has been developed to take into account the tapering sections, geometry changes and adaptations. The coupling with electrons involves simple functions of space, and the model takes space charge into account. Different methods of numerical integration are developed, of which we compare the efficiency. We compared the discrete model with various cold waves amplification models, especially with the model currently used at Thales for the design of their tubes ({texttt{MVTRAD}}). Moreover, we showed that two- or three-dimensional cold wave amplification models like {texttt{MVTRAD}} or {texttt{BWIS}} (which takes into account the backward waves) fail to respect the Maxwell-Faraday equation, contrary to ours. Finally we made a comparison between our circuit discrete model and the amplification model of cold waves in the case of a linear beam.

Afin de faire face aux besoins croissants en énergie, les réacteurs de 4ème génération sont envisagés mondialement. Un premier prototype de réacteur à neutrons rapides à caloporteur sodium (appelé ASTRID) est à l'étude au CEA. Le matériau de référence retenu pour le gainage combustible du premier coeur est l'acier austénitique 15-15Ti - AIM1 (Austenitic Improved Material). <br/>L’objectif de la thèse est d’étudier des voies d’optimisation de la gamme de mise en forme à froid du gainage permettant d’améliorer la résistance au gonflement. Les investigations portent principalement sur les conditions de transformation à froid et les traitements thermiques appliqués au cours de la mise en forme (notamment lors du dernier traitement d’hypertrempe). Les effets de ces paramètres sont étudiés en lien avec la microstructure (notamment l’affinement structural, l’état de précipitation, la remise en solution des éléments d’addition et l’arrangement des dislocations).<br/>La démarche adoptée se divise en trois étapes principales :<br/>- une analyse des gammes de fabrication mises en oeuvre par le passé ainsi qu’une étude des conditions d’étirage à froid et des traitements thermiques appliqués ;<br/>- une évaluation de nouveaux procédés de mise en forme tels que le laminage à pas de pèlerin et le martelage visant à valider la fabrication des tubes finis selon les spécifications requises ;<br/>- une optimisation des gammes de fabrication à froid et de la microstructure du matériau final. Les résultats de caractérisation de la microstructure et du comportement mécanique permettent d’envisager favorablement l’utilisation d’un procédé alternatif tel que le laminage à pas de pèlerin pour fabriquer les tubes de gaine. / In order to face the next century energy demand growth, the worldwide development of the 4th generation of nuclear reactors is considered. The construction of a sodium-cooled fast reactor prototype (ASTRID) is currently envisaged at the CEA. The reference material selected for the fuel cladding of its first core is the 15-15Ti-AIM1 austenitic steel (Austenitic Improved Material).<br/>The goal of this PhD thesis work is to investigate the different ways of optimization for the coldworking steps undergone by the claddings during their manufacture in order to improve their swelling resistance. The main investigations are focused on the conditions of the cold-working steps and the thermal treatments applied throughout the shaping of the claddings, especially of the last solution annealing treatment. The effects of these parameters on the microstructure are investigated (structural refinement, precipitation and the additive elements dissolution and arrangement of the dislocations).<br/>This study is divided into three main steps:<br/>- an analysis of the fabrication routes applied in the past along with the study of the “coldwork” and the thermal treatments conditions;<br/>- an assessment of new shaping processes, such as the “cold-pilgering” and the hammering, in order to verify the conformity of the manufactured tubes with respect to the required specifications.<br/>- an attempt of optimization of the cold-work routes and the microstructure of the final material. The results of microstructure characterization and the mechanical behavior allow envisaging favorably the use of an alternative process such as the cold pilgering to manufacture claddings.

Le développement actuel très rapide des différentes approches « omiques » génère un grand nombre de biomarqueurs potentiels, en particulier dans le domaine de la cancérologie.L’analyse protéomique par spectrométrie de masse a particulièrement bénéficié des progrès technologiques récents qui ont permis la mise au point de nouvelles approches quantitatives globales ou ciblées. Néanmoins, peu de biomarqueurs potentiels finissent par être concrètement utilisés en pratique clinique, nécessitant l’optimisation des différentes étapes de leur développement.Dans la continuité des travaux ayant abouti à l’identification de biomarqueurs diagnostiques dans les hémopathies lymphoïdes B, ce travail de thèse a permis le développement d’une méthode d’analyse protéomique ciblée pour la vérification et la validation de nouveaux biomarqueurs potentiels. La possibilité d’appliquer des stratégies quantitatives globales à un très grand nombre d’échantillons a pu être démontrée. L’application de ces stratégies quantitatives globales à du tissu ganglionnaire provenant de lymphomes agressifs a permis d’identifier des biomarqueurs potentiellement associés à une résistance au traitement. Enfin,le mode de préparation tube-gel, facilitant l’étude d’un grand nombre d’échantillons, a été validé pour la réalisation d’analyses protéomiques différentielles. / The current development of new « omics » technologies has led to the discovery of a large number of potential biomarkers, particularly in the field of oncology. Proteomics analysis bymass spectrometry have particularly benefited from these technological advances with the development of new global or targeted quantitative approaches. Nevertheless, only a few numbers of potential biomarkers are finally used in clinical practice, requiring further optimization of the development process. Following the initial identification of biomarkers in the diagnosis of lymphoid malignancies performed previously, this thesis has allowed the development of a targeted proteomics method that can be used for the validation of new potential biomarkers. The ability of analysing a large number of samples with a global quantitative approach has also been demonstrated. The application of these global quantitative strategies on lymph node tissue of aggressive lymphoma has permitted the identification of potential new biomarkers associated with chemorefractoriness. Lastly, a tube-gel protocol facilitating the analysis of a large number of samples has been validated for differential proteomics studies.

Nous étudions deux phénomènes de transport actif dans la cellule. Cette activité est induite par des moteurs moléculaires. Leur fonctionnement général est compris, mais leurs interactions et fonctions spécifiques font émerger de nouveaux comportements.En première partie nous étudions l'extraction de tubes membranaires par la myosine 1b sur un faisceau d'actine. Ce moteur est non processif, renforcé par la force. Il est impliqué dans une voie de transport membranaire au niveau de l'appareil de Golgi. Nous modélisons ce phénomène. Nous montrons que le renforcement par la force induit l'apparition d'un régime d'extraction par fluctuation géante, et abaisse le nombre de moteurs requis pour l'extraction. Les tubes extraits par des moteurs non processifs ne présentent pas de régime oscillatoire. La croissance du tube peut s'accompagner d'une déplétion avec des moteurs non processifs. Nos prédictions sont en bon accord avec les observations expérimentales.En deuxième partie, nous étudions l'écoulement cytoplasmique dans l'embryon de C.elegans. Sa fonction supposée est le mélange du cytoplasme. Son orientation se renverse aléatoirement. Son mouvement est supporté par des microtubules et des kinésines entrainant le reticulum endoplasmique au niveau cortical. Nous modélisons ce phénomène et montrons que la transition vers l'écoulement est une brisure spontanée de symétrie. Nos prédictions sont en bon accord avec les observations expérimentales. Le point de fonctionnement du système optimise les fluctuations, ce pourrait être le mécanisme du mélange. Nos prédictions sont en bon accord avec les observations expérimentales. / We study two intracellular transport phenomena. They are powered by molecular motors. Motors general mechanisms are understood, but their interactions leads to emerging properties, and some of them have specialised functions.In the first part, we study the extraction of membrane tubes by myosin 1b supported by actin bundles. Myosin 1b is a non processive motor with catch bond property. It is implied in membrane trafficking at the Golgi apparatus level. We model this phenomenon in the frame of a collaboration with experimentalists. We show that catch bond effect induces a regime where tube extraction requires a giant length fluctuation, and the minimal number of motors allowing extraction is decreased. Tubes extracted by non processive motors do not show oscillatory regime. During tube growth motors can deplete with non processive motors. Our predictions are in good agreement with experimental observations.In the second part we study in collaboration with experimentalists the cytoplasmic streaming in C.elegans. Its function is supposed to be the mixing the cytoplasm. Its orientation reverses stochastically. Its movement is supported by microtubules and kinesins, that drive the endoplasmic reticulum at the cortical level. We model this phenomenon and show that the transition toward streaming is a spontaneous spatial symetry breaking. Our predictions are in good agreement with the experimental observations. The parameters values of the system optimize flow fluctuations, this could be the mechanism driving the mixing. Our predictions are in good agreement with experimental observations.

Environment friendly products can be defined as products which show significant environmental improvements made at their most important life-cycle stages. For durable goods, life-cycle stages include manufacturing, use, and end-of-life of product. Reverse Supply Chain Management is the process of planning, implementing, and controlling the efficient, cost effective flow of raw materials, in-process inventory, finished goods and related information from the point of consumption to the point of origin for the purpose of recapturing value and/or proper disposal. The efficient and proper use of 5R’s processes namely Remanufacturing, Refurbishment, Reuse, Repair; and Recycle help the product to be greener and environment friendly. Part of the process also includes the proper disposal of goods which is essential for maintaining a green environment. This study aims at finding the significant factors to be considered by Cathode Ray Tube (CRT) Television component manufacturers to manufacture Environment Friendly Product. Various parameters like raw material procurement; water and energy consumption in product manufacturing; the extent of environmental regulations followed; waste production; and waste processing have been considered in this study. A Case Study has been prepared to study the entire manufacturing process of a CRT Television. The case study also looks at the regulations followed by CRT TV component manufacturers in India and how they are different from other countries. An attempt has been made to find out the value which can be recovered at the End-Of-Life of CRT TVs. The case also looks at safe recycling options for CRT TVs. The study shows that CRT TV component manufacturers consider Resource Procurement, Energy Utilization; and Compliance with Regulations to a significant extent. Also, an attempt has been made to develop an Environmental Friendly Index (EFI). The EFI depends on resource procurement, energy utilization, waste production, waste processing, and existence of environmental team in the company. There have been no steps taken by these component manufacturers towards dealing with return goods. All the return goods are dealt with by recyclers, who extract the material through unscientific and non-environmental friendly ways. The recyclers are not able to extract all the useful material, which if done in an efficient way, will result in more material recovery.