During the past two decades, many researchers have developed methods for the detection of structural defects at the early stages to operate the aerospace vehicles safely and to reduce the operating costs. The Surface Response to Excitation (SuRE) method is one of these approaches developed at FIU to reduce the cost and size of the equipment. The SuRE method excites the surface at a series of frequencies and monitors the propagation characteristics of the generated waves. The amplitude of the waves reaching to any point on the surface varies with frequency; however, it remains consistent as long as the integrity and strain distribution on the part is consistent. These spectral characteristics change when cracks develop or the strain distribution changes. The SHM methods may be used for many applications, from the detection of loose screws to the monitoring of manufacturing operations. A scanning laser vibrometer was used in this study to investigate the characteristics of the spectral changes at different points on the parts. The study started with detecting a load on a plate and estimating its location. The modifications on the part with manufacturing operations were detected and the Part-Based Manufacturing Process Performance Monitoring (PbPPM) method was developed. Hardware was prepared to demonstrate the feasibility of the proposed methods in real time. Using low-cost piezoelectric elements and the non-contact scanning laser vibrometer successfully, the data was collected for the SuRE and PbPPM methods. Locational force, loose bolts and material loss could be easily detected by comparing the spectral characteristics of the arriving waves. On-line methods used fast computational methods for estimating the spectrum and detecting the changing operational conditions from sum of the squares of the variations. Neural networks classified the spectrums when the desktop – DSP combination was used. The results demonstrated the feasibility of the SuRE and PbPPM methods.

Many research studies have analyzed the effect that whole-body vibration (WBV) has on sleep, and some have sought to use vibration to treat sleep disorders such as insomnia. It has been shown that low frequencies (f < 2Hz) are generally sleep inducing, but oscillations of this frequency are typically difficult to achieve using electromagnetic vibration drives. In the research that has been performed, optimal vibration parameters have not been determined, and the effects of multiple vibration sources vibrating at different frequencies to induce a low frequency traveling wave have not been explored. Insomnia affects millions of people worldwide, and non-pharmacological treatment options are limited. A bed excited with multiple vibration sources was used to explore beat frequency vibration as a non-pharmacological treatment for insomnia. A repeated measures design pilot study of 14 participants with mild-moderate insomnia symptom severity was conducted to determine the effects of beat frequency vibration, and traditional standing wave vibration on sleep latency and quality. Participants were monitored using high-density electroencephalography (HD-EEG). Sleep latency was compared between treatment conditions. Trends of a decrease in sleep latency due to beat frequency vibration were found (p ≤ 0.181 for AASM latency, and p ≤ 0.068 for unequivocal sleep latency). Neural complexity during wake, N1, and N2 stages were compared using Multi-Scale Sample Entropy (MSE), which demonstrated significantly lower MSE between wake and N2 stages (p ≤ 0.002). Lower MSE was found in the transition from wake to N1 stage sleep but did not reach significance (p ≤ 0.300). During N2 sleep, beat frequency vibration shows lower MSE than the control session in the left frontoparietal region. This indicates that beat frequency vibration may lead to a decrease of conscious awareness during deeper stages of sleep. Standing wave vibration caused reduced Alpha activity and increased Delta activity during wake. Beat frequency vibration caused increased Delta activity during N2 sleep. These preliminary results suggest that beat frequency vibration may help individuals with insomnia symptoms by decreasing sleep latency, by reducing their conscious awareness, and by increasing sleep drive expression during deeper stages of sleep. Standing wave vibration may be beneficial for decreasing expression of arousal and increasing expression of sleep drive during wake, implying that a dynamic vibration treatment may be beneficial. The application of vibration treatment as part of a heuristic sleep model is discussed.

No description available.

Experimental vibration analysis of mechanical structures is a well established field.Plenty of literature exists on macro scale structures in the fields of civil, mechanical and aerospace engineering, but the study of vibrations of micro scale structures such as MEMS, liquid droplets, and biological cells is relatively new. For such structures, the amplitudes of vibration are typically in nanometeror sub-nanometer range and the frequencies are in KHz to MHz range depending upon the dimensions of the structure. In our study, we use a scanningLaser Doppler Vibrometer (LDV) to measure the vibrations of micro-scale objects such as MEMS structures, micro droplets and cells. The vibrometercan capture frequency response up to 24 MHz withpicometer displacement resolution. First, we present the study of dynamics of a 2-D micromechanical structure—a MEMSelectrothermal actuator. The structure is realized using SOI MUMPs process from MEMSCAP. The fabricated device is tested for its dynamic performance characteristics using the LDV. In our experiments, we could capture up to 50 out-of-plane modes of vibration—an unprecedented capture—with a single excitation. Subsequent FEM based numerical simulations confirmed that the captured modes were indeed what the experiments indicated, and the measured frequencies werefound to be within 5% of theoretically predicted. Next, we study the dynamics of a 3-D micro droplet and show how the substrate adhesion modulates the natural frequency of the droplet. Adhesion properties of droplets are decided by the degree of wettability that is generally measured by the contact angle between the substrate and the droplet. In this work, we were able to capture 14 modes of vibration of a mercury droplet on different substrates and measure the correspondingfrequencies experimentally. We verify these frequencies with analytical calculations and find that all the measured frequencies are within 6% of theoretically predicted values. We also show that considering any two pairs of natural frequencies, we can calculate the surface tension and the contact angle, thus providing a new method for measuring adhesion of a droplet on an unknown surface. Lastly, we present a study of vibrations of biological cells.Our first study is that of single muscle fibers taken from drosophila.Muscle fibers with different pathological conditions were held in two structural configurations—asa fixed-fixed beam and a cantilever beam—and their vibration signatures analysed.We found that there was significant reduction in natural frequency of diseased fibers. Among the diseased fibers, we could confidently classify the myopathies into nemaline and cardiac types based on the natural frequency of single fibers. We have noticed that the elastic modulus of the muscle which decides the natural frequency is dictated by the myosin expression levels. Our last example isa study of the vibration signatures of cancer cells. Here we measure the natural frequencies of normal and certain cancerous cells, and show that we can distinguish the two based on their natural frequencies. We find that the natural frequency of cancerous cells is approximately half of that of normal cells. Within the cancerous cells, we are able to distinguished epithelial cancer cells and mesenchymal cancer cells based on their natural frequency values. For Epithelial cells,we activate the signaling pathways to induce EMT and notice the reduction in the natural frequency. This mechanical assay based on vibration response corroborates results from the biochemical assays such as Western blots and PCR, thus opening a new technique of mechano-diagnostics.

This diploma thesis deals with the theoretical description of interference methods used to measure vibrations, examines main parasitic effects and analyses its contribution to achievable the resolution. In the practical part, it uses several measurements to verify the effects of the level of reflected beam, stand-off distance and speckle noise. It also proposes a practical experiment for measuring dynamic parameters and signal-noise ratio. Results show that, the noise is exponentially dependent on the level of the reflected beam. The visible maximum of the vibrometer proved to be critical in terms of time stability of the measured signal level in two of the three measurements. Results of the dynamic measurement show that, the measured deviations were not degraded or significantly disturbed by the noise signal. From the measurement of the speckle noise, it emerged that the lowest level of noise is achieved with smooth and highly reflective materials.

Les dispositifs d’isolation galvanique intégrés au sein des systèmes de commande d’interrupteurs de puissance doivent répondre à une demande accrue en performance, facilité d’intégration et efficacité énergétique. Les transducteurs ultrasonores capacitifs micro-usinés (cMUT : capacitive Micromachined Ultrasonic Transducer), capables d’émettre et de recevoir des ondes ultrasonores, semblent une alternative tout à fait nouvelle à la fonction d’isolation galvanique. Ces travaux de thèse ont pour objectif de démontrer la faisabilité d’un dispositif basé sur la technologie cMUT. Le principe de fonctionnement consiste à transmettre une information grâce à une communication par onde acoustique de volume entre deux réseaux de cMUT placés de part et d’autre d’un substrat. Nous focalisons, en premier lieu, ces travaux sur le processus de fabrication par micro-usinage de surface des cMUT ainsi que les techniques de réalisation des dispositifs en structure double face sur substrat de silicium. L’étude permet d’identifier le collage de substrat comme une solution de fabrication industrialisable. Suite à la réalisation des dispositifs, la caractérisation électro-mécanique des cMUT est une étapeessentielle à la validation de leur fonctionnalité en tant que dispositifs émetteurs. L’étude débute par uneévaluation des propriétés mécaniques du matériau constituant la membrane et qui impactent directementle comportement global des cMUT. Puis, la caractérisation du comportement statique et dynamique descMUT permet d’extraire les paramètres tels que la fréquence de résonance, la tension de collapse etl’efficacité électro-mécanique qui définissent le mode de pilotage d’un tel système.Finalement, la validation du concept de transmission et de détection d’ondes ultrasonores est réaliséegrâce à des mesures de vibrométrie laser Doppler. Les résultats apportent des éléments de réponse quantau mode de propagation des ondes et permettent d’identifier les topologies de meilleure efficacité entransmission acoustique. Enfin, l’intégration du prototype dans l’application de commanded’interrupteur de puissance démontre la faisabilité du concept de transformateur acoustique basé sur latechnologie cMUT. / Galvanic isolation devices integrated into switch command systems must be able to answer all of the increasing demand for performance, energetic efficiency and integration easiness. The capacitive micro machined ultrasonic transducers (cMUT), able to emit and receive ultrasounds, could be an entirely new alternative to the function of galvanic isolation. This work aims to demonstrate the feasibility of a cMUT-based device. The operating principle consists in transmitting information thanks to a bulk acoustic wave between two cMUT arrays located on both sides of a substrate. We first focus on cMUT surface micromachining fabrication process and techniques of double-side device manufacturing. Our study allows us to identify wafer bonding as a realistic industrial solution. After device fabrication, electro-mechanical of cMUT is an essential step to validate their functionality as ultrasonic emitters. The study starts with the mechanical properties evaluation of the membrane material. These properties directly impact the global behavior of cMUT. Then, the characterization of cMUT static and dynamic behavior allows extracting parameters as resonance frequency, collapsing voltage and electro-mechanical efficiency which define the actuation mode of such a system. Finally, the validation of transmission and reception of ultrasonic waves is evaluated by vibrometer laser Doppler measurements. Results bring elements concerning the waves propagation modes and allow identifying the best acoustical efficiency in regard to the topology. In conclusion, the prototype integration in the application of power switch command demonstrates the feasibility of acoustic transformer concept based on cMUT technology.

Les microphones capacitifs sont des transducteurs réciproques dont les qualités (sensibilité, bande passante et tenue dans le temps) en font des instruments de mesure performants. Couramment utilisés jusqu’à présent en récepteurs dans l’air à pression atmosphérique et à température ambiante, dans la gamme de fréquences audibles, ils sont correctement caractérisés dans ce cadre depuis près de trente ans. Mais aujourd’hui, leur miniaturisation (par procédé MEMS) et leur usage nouveau en métrologie fine (en récepteurs comme en émetteurs) - qui exigent une connaissance précise de leur comportement dans des domaines de fréquences élevées (jusqu’à 100 kHz), dans des mélanges gazeux aux propriétés différentes de celles de l’air et dans des conditions de pression et de température beaucoup plus élevées ou beaucoup plus basses que les conditions standards - nécessitent une caractérisation beaucoup plus approfondie, aussi bien en terme de modélisation qu’en terme de résultats expérimentaux. C’est ainsi que ici -i/ les effets des couches limites thermiques (seules les couches limites visqueuses sont habituellement retenues) sont introduits dans le modèle, ce qui amène dans le chapitre premier à une étude analytique de la diffusion thermique en parois minces (dont la portée dépasse le cadre strict du transducteur), -ii/ l’influence des orifices de l’électrode arrière sur la déformée de la membrane est traitée au départ par une méthode analytique originale, qui permet de traduire les conditions en frontière non uniformes sur la surface de l’électrode sous forme de sources locales virtuelles, associées à des conditions de frontière rendues uniformes (chapitre second), -iii/ des solutions analytiques nouvelles, dépendant à la fois des coordonnées radiales et azimutales, sont obtenues pour le champ de déplacement de la membrane et pour les champs de pression dans les cavités du microphone par usage de théories modales compatibles avec les couplages multiples qui y prennent place (troisième chapitre), -iv/ un modèle de « circuit à constantes localisées » (reporté pour l’essentiel en annexe) est proposé, à des degrés divers de précision, qui permet en particulier d’accéder de façon simple à la sensibilité et au bruit thermique du microphone (fin du quatrième chapitre), -v/ une étude au vibromètre laser à balayage a été réalisée (début du quatrième chapitre), qui permet non seulement de mettre en évidence pour la première fois les déformées de membrane complexes qui apparaissent en hautes fréquences, mais encore de les quantifier et par-delà de valider les résultats théoriques obtenus et donc les modèles proposés (même s’ils restent perfectibles comme indiqué dans la conclusion). / Condenser microphones are reciprocal transducers whose properties (sensitivity, bandwidth and reliability) make them powerful measurement tools. So far, they have been commonly used as receivers in the audible frequency range, in air at atmospheric pressure and ambient temperature, they have been appropriately characterised in this context for nearly thirty years. But nowadays, their miniaturisation (using MEMS processes) and their new use for metrological purposes (as receivers as well as transmitters) require much deeper theoretical and experimental characterisations because they require an accurate knowledge of their behaviour in high frequency ranges (up to 100 kHz), in gas mixtures, whose properties differ from those of air, and under pressure and temperature conditions much higher or much lower than standard conditions. Thus, here, -i/ the effects of the thermal boundary layers are introduced in the model (only viscous boundary layers are usually accounted for), leading, in the first chapter, to an analysis of the thermal diffusion of thin bodies (whose scope is beyond the strict frame of capacitive transducers), ii/ the influence of the holes in the backing electrode on the dynamic behaviour of the membrane is initially handled with an original analytical method which allows expressing the non-uniform boundary conditions at the surface of the backing electrode as fictitious localised sources associated to uniform boundary conditions (second chapter), -iii/ new analytical solutions, depending both on the radial and azimuthal coordinates, for the pressure field and for the displacement field inside the cavities behind the membrane are expressed using modal theories in agreement with the strong couplings which occur between the different parts of the transducer (chapter three), -iv/ "lumped element circuits", which are more or less approximated (presented in the Appendix), more particularly result in expressing and assessing the sensitivity and the thermal noise (end of chapter three), -v/ experimental results, obtained from measurements of the displacement field of the membrane using a laser scanning vibrometer, both highlight and quantify for the first time the complex behaviour of the membrane in the highest frequency range, and finally lead to the validation of the theoretical results and therefore, the models presented here (even if the latter may still be improved as outlined in the conclusion).