A 50 MHz Frequency Modulated Continuous Wave (FMCW) radar system, developed at the University of Saskatchewan to provide improved spatial and temporal resolution measurements of auroral E-region plasma processes, introduces ambiguous spectral information, due to spectral ghosting, for scattering events in which multiple radar echoes are detected. This thesis identifies two Linearly Frequency Modulated (LFM) radar waveforms used by the FMCW system as the source of the ghosting. An analysis procedure designed to counteract the spectral ghosting problem is developed but is not an ideal solution, and therefore replacement of the LFM waveforms is recommended.<p> A detailed investigation of alternative radar waveforms using the Ambiguity Function and Ambiguity Diagram techniques is performed. A frequency coded continuous wave radar waveform based on a composite Costas sequence is proposed as a successor to the LFM waveforms. The composite Costas radar waveform will conserve the spatial and temporal resolutions extended by the LFM waveforms and preclude any spectral ghosting. Implementing the proposed radar waveform and avoiding receiver saturation issues with the mono-static FMCW radar system in which both the transmitting and receiving antenna arrays are simultaneously and continuously active and geographically co-located is also discussed.<p> In addition to this, two 50 MHz backscatter events are presented in this thesis to demonstrate the effectiveness of the FMCW system, notwithstanding the spectral ghosting complication. The first event from November 21, 2009 is identified as a Type 1 instability and the second from September 13, 2009 is identified as a Type 2 instability which lasted for ~ 16 minutes. Linear plasma fluid theory is used to provide a brief interpretation of both scattering events.

A 50 MHz Frequency Modulated Continuous Wave (FMCW) radar system, developed at the University of Saskatchewan to provide improved spatial and temporal resolution measurements of auroral E-region plasma processes, introduces ambiguous spectral information, due to spectral ghosting, for scattering events in which multiple radar echoes are detected. This thesis identifies two Linearly Frequency Modulated (LFM) radar waveforms used by the FMCW system as the source of the ghosting. An analysis procedure designed to counteract the spectral ghosting problem is developed but is not an ideal solution, and therefore replacement of the LFM waveforms is recommended.<p> A detailed investigation of alternative radar waveforms using the Ambiguity Function and Ambiguity Diagram techniques is performed. A frequency coded continuous wave radar waveform based on a composite Costas sequence is proposed as a successor to the LFM waveforms. The composite Costas radar waveform will conserve the spatial and temporal resolutions extended by the LFM waveforms and preclude any spectral ghosting. Implementing the proposed radar waveform and avoiding receiver saturation issues with the mono-static FMCW radar system in which both the transmitting and receiving antenna arrays are simultaneously and continuously active and geographically co-located is also discussed.<p> In addition to this, two 50 MHz backscatter events are presented in this thesis to demonstrate the effectiveness of the FMCW system, notwithstanding the spectral ghosting complication. The first event from November 21, 2009 is identified as a Type 1 instability and the second from September 13, 2009 is identified as a Type 2 instability which lasted for ~ 16 minutes. Linear plasma fluid theory is used to provide a brief interpretation of both scattering events.

Orientador: Orlando Petrucci Junior / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Ciências Médicas / Made available in DSpace on 2018-08-24T07:48:01Z (GMT). No. of bitstreams: 1 Assumpcao_AntonioCarlos_D.pdf: 13951044 bytes, checksum: 4ebd9040bcd7ea540e6927bdc4258384 (MD5) Previous issue date: 2013 / Resumo: Introdução: O aumento do limiar de estimulação ventricular (LEV) tem sido observado após a administração de choque elétrico de cardioversão/desfibrilação transtorácico (CDT) para desfibrilação ventricular, contudo, poucos estudos têm avaliado este fenômeno no que diz respeito à energia e a forma de onda empregada para a CDT. Este estudo analisou o LEV após CDT de 360J, comparando-se os resultados após aplicação de onda de energia Mono e Bi. Método: Em suínos Landrace femininos foram implantados sistema de estimulação permanente de marcapasso, divididos em três grupos: sem indução de fibrilação ventricular (FV) e CDT com formato de onda monofásica (Mono) e bifásica (Bi) (Grupo I); indução FV, um minuto de observação sem intervenção, dois minutos de massagem cardíaca externa, e CDT Mono e Bi (Grupo II) e indução de FV, dois minutos de observação sem intervenção, quatro minutos de massagem cardíaca externa e CDT Mono e Bi (Grupo III). Após CDT, o LEV foi avaliado a cada minuto durante dez minutos. Resultados: Um total de 143 experimentos foram concluídos. No final do período de observação, os grupos I e II mostraram valores constantes LEV. O Grupo III mostrou aumento no LEV Mono e Bi com energia externa, sem diferença entre os formatos de ondas externas. O formato Mono foi associada a valores mais elevados de LEV quando o tempo de parada cardiorrespiratória (PCR) foi maior, o que não foi verificado na Bi. Conclusão: A CDT não tem impacto significativo sobre o LEV. Com onda Mono, observou-se aumento do LEV quando o período de PCR foi mais longo / Abstract: Introduction. Although an increase in the ventricular pacing threshold (VPT) has been observed after administration of transthoracic shock for ventricular defibrillation, few studies have evaluated the phenomenon in respect to the defibrillation waveform energy. Therefore, this study examined the VPT behavior after transthoracic shock with a monophasic or biphasic energy waveform. Method. Domestic Landrace female piglets implanted with a permanent pacemaker stimulation system were divided into 3 groups: no ventricular fibrillation (VF) induction and transthoracic shock with monophasic or biphasic energy (group I); VF induction, 1 minute of observation without intervention, 2 minutes of external cardiac massage, and transthoracic shock with monophasic or biphasic energy (group II); and VF induction, 2 minutes of observation without intervention, 4 minutes of external cardiac massage, and transthoracic shock with monophasic or biphasic energy (group III). After external shock, the VPT was evaluated every minute for 10 minutes. Results. A total of 143 experiments were performed. At the end of the observation period, groups I and II showed steady VPT values. Group III showed an increase in VPT with monophasic or biphasic external energy, with no difference between the external energy sources. The monophasic but not the biphasic waveform was associated with higher VPT values when the VF was longer. Conclusion. Defibrillation does not have a significant impact on pacing threshold, but a longer VF period is related to a higher VPT after defibrillation with monophasic waveform / Doutorado / Fisiopatologia Cirúrgica / Doutor em Ciências

Complex optical pulse shapes are typically generated from ultrashort laser pulses by manipulating the optical spectrum of the input pulses. This generates complex but periodic time-domain waveforms. Optical Arbitrary Waveform Generation (OAWG) builds on the techniques of ultrashort pulse-shaping, with the goal of making non-periodic, truly arbitrary optical waveforms. Some applications of OAWG are coherently controlling chemical reactions on a femtosecond time scale, improving the performance of LADAR systems, high-capacity optical telecommunications and ultra wideband signals processing. In this work, an array of Vertical Cavity Surface Emitting Lasers (VCSELs) are used as modulators, by injection-locking each VCSEL to an individual combline from an optical frequency comb source. Injection-locking ensures that the VCSELs' emission is phase coherent with the input combline, and modulating its current modulates mainly the output optical phase. The multi-GHz modulation bandwidth of VCSELs updates the output optical pulse shape on a pulse-to-pulse time scale, which is an important step towards true OAWG. In comparison, it is about a million times faster than the liquid-crystal modulator arrays typically used for pulse shaping! Novel components and subsystems of Optical Arbitrary Waveform Generation (OAWG) are developed and demonstrated in this work. They include: 1. Modulators An array of VCSELs is packaged and characterized for use as a modulator for rapid?update pulse?shaping at GHz rates. The amplitude and phase modulation characteristics of an injection-locked VCSEL are simultaneously measured at GHz modulation rates. 2. Optical Frequency Comb Sources An actively mode-locked semiconductor laser was assembled, with a 12.5 GHz repetition rate, ~ 200 individually resolvable comblines directly out of the laser, and high frequency stability. In addition, optical frequency comb sources are generated by modulation of a single frequency laser. 3. High-resolution optical spectral demultiplexers The demultiplexers are implemented using bulk optics, and are used to spatially resolve individual optical comblines onto the modulator array. 4. Optical waveform measurement techniques Several techniques are used to measure generated waveforms, especially for spectral phase measurements, including multi-heterodyne phase retrieval. In addition, an architecture for discriminating between ultrashort encoded optical pulses with record high sensitivity is demonstrated.

This thesis focuses on the comprehensive and thorough studies on the geospatial processing of airborne (full) waveform lidar data, including waveform modeling, direct georeferencing, and precise georeferencing with self-calibration.<div><br></div><div>Both parametric and nonparametric approaches of waveform decomposition are studied. The traditional parametric approach assumes that the returned waveforms follow a Gaussian mixture model where each component is a Gaussian. However, many real examples show that the waveform components can be neither Gaussian nor symmetric. To address the problem, this thesis proposes a nonparametric mixture model to represent lidar waveforms without any constraints on the shape of the waveform components. To decompose the waveforms, a fuzzy mean-shift algorithm is then developed. This approach has the following properties: 1) it does not assume that the waveforms follow any parametric or functional distributions; 2) the waveform decomposition is treated as a fuzzy data clustering problem and the number of components is determined during the process of decomposition; 3) neither peak selection nor noise floor filtering prior to the decomposition is needed; and 4) the range measurement is not affected by the process of noise filtering. In addition, the fuzzy mean-shift approach is about three times faster than the conventional expectationmaximization algorithm and tends to lead to fewer artifacts in the resultant digital elevation model. <br></div><div><br></div><div>This thesis also develops a framework and methodology of self-calibration that simultaneously determines the waveform geospatial position and boresight angles. Besides using the flight trajectory and plane attitude recorded by the onboard GPS receiver and inertial measurement unit, the framework makes use of the publically accessible digital elevation models as control over the study area. Compared to the conventional calibration and georeferencing method, the new development has minimum requirements on ground truth: no extra ground control, no planar objects, and no overlap flight strips are needed. Furthermore, it can also solve the problem of clock synchronization and boresight calibration simultaneously. Through a developed two-stage optimization strategy, the self-calibration approach can resolve both the time synchronization bias and boresight misalignment angles to achieve a stable and correct solution. As a result, a consistency of 0.8662 meter is achieved between the waveform derived digital elevation model and the reference one without systematic trend. Such experiments demonstrate the developed method is a necessary and more economic alternative to the conventional, high demanding georeferencing and calibration approach, especially when no or limited ground control is available.<br></div>

none

Recovering clean speech from an audio signal with additive noise is a problem that has plagued the signal processing community for decades. One promising technique currently being utilized in speech-coding applications is a multi-sensor approach, in which a microphone is used in conjunction with optical, mechanical, and electrical non-acoustic speech sensors to provide greater versatility in signal processing algorithms. One such non-acoustic glottal waveform sensor is the Tuned Electromagnetic Resonator Collar (TERC) sensor, first developed in [BLP+02]. The sensor is based on Magnetic Resonance Imaging (MRI) concepts, and is designed to detect small changes in capacitance caused by changes to the state of the vocal cords - the glottal waveform. Although preliminary simulations in [BLP+02] have validated the basic theory governing the TERC sensor's operation, results from human subject testing are necessary to accurately characterize the sensor's performance in practice. To this end, a system was designed and developed to provide real-time audio recordings from the sensor while attached to a human test subject. From these recordings, executed in a variety of acoustic noise environments, the practical functionality of the TERC sensor was demonstrated. The sensor in its current evolution is able to detect a periodic waveform during voiced speech, with two clear harmonics and a fundamental frequency equal to that of the speech it is detecting. This waveform is representative of the glottal waveform, with little or no articulation as initially hypothesized. Though statistically significant conclusions about the sensor's immunity to environmental noise are difficult to draw, the results suggest that the TERC sensor is considerably more resistant to the effects of noise than typical acoustic sensors, making it a valuable addition to the multi-sensor speech processing approach.

L’atténuation sismique est un paramètre physique très utile pour décrire et imager les propriétés du sous-sol, et tout particulièrement les roches saturées et les nuages de gaz. Les approches classiques analysent l’amplitude du spectre des données ou bien la distorsion de ce spectre, avec des méthodes asymptotiques. L’inversion des formes d’onde (Full Waveform Inversion en anglais, FWI) est une approche alternative qui prend en compte les aspects de fréquences finies. En pratique, à la fois les vitesses et l’atténuation doivent être déterminées. Il est connu que l’inversion multi-paramètre ne conduit pas à un résultat unique.Ce travail se focalise sur la détermination des vitesses et de l’atténuation. La dispersion liée à l’atténuation produit des modèles de vitesse équivalents en termes de cinématique. Je propose une inversion hybride : la « relation cinématique » est un moyen de guider l’inversion des formes d’onde non-linéaire. Elle se décompose en deux étapes. Dans un premier temps, l’information cinématique est remise à jour, et ensuite les vitesses et l’atténuation sont modifiées, pour une cinématique donnée. Différentes approches sont proposées et discutées au travers d’applications sur des données synthétiques 2D, en particulier sur les modèles Midlle-East et Marmousi. / Seismic attenuation is a useful physical parameter to describe and to image the properties of specific geological bodies, e.g., saturated rocks and gas clouds. Classical approaches consist of analyzing seismic spectrum amplitudes or spectrum distortions based on ray methods. Full waveform inversion is an alternative approach that takes into account the finite frequency aspect of seismic waves. In practice, both seismic velocities and attenuation have to be determined. It is known that the multi-parameter inversion suffers from cross-talks.This thesis focuses on retrieving velocity and attenuation. Attenuation dispersion leads to equivalent kinematic velocity models, as different combinations of velocity and attenuation have the same kinematic effects. I propose a hybrid inversion strategy: the kinematic relationship is a way to guide the non-linear full waveform inversion. The hybrid inversion strategy includes two steps. It first updates the kinematic velocity, and then retrieves the velocity and attenuation models for a fixed kinematic velocity. The different approaches are discussed through applications on 2D synthetic data sets, including the Midlle-East and Marmousi models.

In mining engineering, blast-induced ground vibration has become one of the major concerns when production blasts are conducted, especially when the mining areas and the blast sites are near inhabited areas or infrastructure of interest. To comply with regulations, a vibration monitoring program should be developed for each mining operation. The vibration level, which is usually indicated by the peak particle velocity (PPV) of the vibration waveform, should fall below the maximum allowable values. Ideally, when blasting is near structures of interest (power towers, dams, houses, etc.), the vibration level (PPV) should be predicted prior to the actual production blasts. There are different techniques to predict the PPV, one in particular is the signature hole technique. This technique is based on signals and systems theory and uses a mathematical operation called convolution to assess the waveform of the production blast. This technique uses both the vibration waveform of an isolated hole and the timing function given by the timing used in the blast. The signature hole technique requires an isolated single-hole waveform to create a prediction. Sometimes this information is difficult to acquire, as it requires the synthesis of a single-hole vibration waveform from a production blast vibration signal. The topic of ground vibrations from mining blasts, and more specifically the synthesis of a single-hole vibration waveform, has been studied by researchers in past decades, but without any concrete success. This lack of success may be partially due to the complexity and difficulty of modelling and calculation. However, this inverse methodology can be very meaningful if successfully applied in blasting engineering. It provides a convenient and economical way to obtain the single-hole vibration waveform and make the prediction of a production blast waveform easier. This dissertation research involves the theories of deconvolution, linear superposition, and Fourier phases to recover single-hole vibration waveforms from a production waveform. Preliminary studies of deconvolution included spectral division deconvolution and Wiener filtering deconvolution. In addition to the adaptation of such methodologies to the blast vibrations problems, the effectiveness of the two deconvolution methods by the influence of delay interval and number of holes is also discussed. Additionally, a new statistical waveform synthesis method based on the theories of linear superposition, properties of Fourier phase, and group delays was developed. The validation of the proposed methodology was also conducted through several field blasting tests. Instead of synthesizing one normalized single-hole vibration waveform by deconvolution, the proposed statistical waveform synthesis methodology generates a different single-hole vibration waveform for each blast hole. This method is more effective and adaptable when synthesizing single-hole vibration waveforms. Recommendations for future work is also provided to improve the methodology and to study other inverse problems of blast vibrations.

Une utilisation intelligente de l’espace Hertzien sera nécessaire pour permettre aunombre croissant d’objets sans-fil connectés de communiquer dans le même espace de propagation.Ces travaux de thèse proposent une architecture d’émetteur radiofréquence flexible, faiblecoût et faible consommation, en rupture avec les techniques conventionnelles. Cet émetteur estfondé sur un encodage de la dérivée du signal à générer, ce qui permet de réduire le coût énergétiquede la conversion de l’information. Un convertisseur numérique analogique compatibleavec cette architecture est présenté et ses performances sont évaluées dans le cadre de la générationde signaux radiofréquence. Les résultats de mesures obtenus avec un prototype réalisé entechnologie CMOS 65 nm apporte la preuve du concept. / The increasing density of wireless devices and the associated communication flowssharing the same air interface will require a smart and agile use of frequency resources. Thisthesis proposes a flexible, low cost and low power disruptive transmitter architecture. It usesa differentiating coding scheme which leverages a mathematical and technological reduction ofthe energy cost of information conversion. The design of a DAC suited to this architecture isdeveloped and its performances are assessed toward RF signal generation. The measurementsof a demonstrator designed in 65 nm CMOS technology bring a proof of concept.