Membranas à base de polímeros perfluorosulfonados, como a Nafion, vêm sendo extensivamente usadas como membrana de troca protônica em células a combustível (FC). O objetivo deste trabalho foi desenvolver membranas eletrólito à base de polindeno sulfonado (SPInd) e poli(fluoreto de vinilideno) (PVDF), para uso como membranas de troca protônica em condições semelhantes às da membrana Nafion. As membranas foram preparadas por casting em diferentes composições utilizando PVDF como reforço mecânico e PVDF sulfonado (SPVDF) como agente compatibilizante. Todas as membranas foram avaliadas por análise termogravimétrica, calorimetria exploratória diferencial, análise dinâmico mecânica, microscopia eletrônica de varredura, grau de inchamento, capacidade de troca iônica e espectroscopia de impedância eletroquímica. As membranas com características semelhantes à membrana Nafion foram avaliadas em protótipo de FC a 80 °C. A membrana SPInd50/PVDF e as membranas com agente compatibilizante apresentaram condutividades iônicas na ordem de 10-2 S/cm, comparáveis àquela da membrana Nafion. A membrana com melhor desempenho em protótipo de FC foi o SPInd/PVDFC12, preparado com 50% de SPInd, 47,5% de PVDF e 2,5% de SPVDF (p/p), cujos valores de potencial de circuito aberto e densidade de potência máximo foram de 1,02 V e 74,54 mW/cm2, respectivamente. Apesar da densidade de potência máxima ser inferior à da membrana Nafion (603 mW/cm2), a membrana SPInd/PVDFC12 apresenta potencial para uso como eletrólito em célula a combustível. / Perfluorosulfonic acid ionomer membranes, e.g. Nafion, have been extensively used as proton exchange membranes in fuel cells (FC) due to their high proton conductivity and good mechanical properties. The aim of this work was to develop electrolyte membranes based on sulfonated polyindene (SPInd) and poly(vinylidene fluoride) (PVDF) to be used in the same conditions as Nafion. Membranes were prepared by casting with different compositions using PVDF as mechanical reinforcement and sulfonated PVDF (SPVDF) as coupling agent. The produced membranes were evaluated by thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis, scanning electron microscopy, water uptake, ion exchange capacity and electrochemical impedance spectroscopy. The membranes with similar results to Nafion, were evaluated in a FC prototype at 80 °C. The membrane SPInd50/PVDF and all the membranes with coupling agent had ionic conductivity in the order of 10-2 S/cm, comparable to the Nafion´s. The polyelectrolyte with the best performance was the SPInd/PVDFC12 which was prepared with 50 wt% SPInd, 47.5 wt% PVDF and 2.5 wt% SPVDF, that reached an open circuit voltage of 1.02 V and maximum power density of 74.54 mW/cm2. Even though Nafion´s maximum power density was higher (603 mW/cm2), the SPInd/PVDFC12 membrane showed potential to be used as electrolyte in fuel cells.

The main purpose of this thesis was to investigate and characterize the use of piezoelectric yarn for use in textile (fingertip) pressure sensors in glove applications. Such applications could include healthcare, security and safety, game applications or intelligent control. Piezoelectric materials generate a voltage when pressed or squeezed. Poly(vinylidene fluoride) (PVDF) is a polymorphic material with piezoelectric properties. PVDF yarns were integrated into block sensors. These blocks consist of thermoplastic material glued to a knitted supporting fabric. The electrical signal given off by the PVDF yarn was measured with the help of an oscilloscope. The block sensor generated a distinguishable signal under a dynamic compression of 0.003 N, indicating that the structure is sensitive enough compared to the average male fingertip sensitivity threshold (0.0054N). / Program: Master programme in Textile Engineering

<div>For over 20 years, biaxially oriented polypropylene (BOPP) has been used in capacitors as the dielectric material. BOPP has very high breakdown strength, low electric loss, and is relatively inexpensive however, it suffers from low dielectric constant and low usage temperature. The ever growing technology market requires more robust capacitors which can be used in high temperature and pulsed power applications, and the aim of this research is to meet or exceed dielectric properties of BOPP by combining specific polymer materials in layered structures, biaxially orienting the films, and heat setting the films to further improve thermal stability. Post-processing is done on custom built machines which track real-time true stress, true strain and birefringence values, allowing for a more complete picture of mechano-optical properties generated during the stretching process. These data, along with offline characterization techniques such as X-ray scattering and DSC, were coupled with dielectric property testing to help form relationships between polymer processing, morphology, and dielectric properties.</div><div><br></div><div>In Chapter 3, microlayer PET and PVDF (50:50 ratio) films with 32 total layers and thickness around 125 micron were provided by PolymerPlus. Films were first stretched uniaxially at varying temperatures in order to optimize processing conditions. Characterization confirmed PVDF crystal form transformation from alpha to beta form when films were stretched at 95^oC, and presence of - PVDF when stretched in molten state at 185^oC, sandwiched between solid PET layers. Dielectric properties were tested for films stretched at 150^oC, which exhibited low dielectric constant when PVDF spherulites or smaller, broken up fibrils were present, but improved dielectric constant when PVDF morphology consisted of long, highly ordered fibrils. Uniaxial drawing helped lower dielectric loss, and it further signicantly decreased at very high strains. In this case, morphology of uniaxially drawn PET did not have a strong correlation with dielectric constant, but higher PET crystallinity and orientation likely helps to lower dielectric losses.</div><div><br></div><div>Polymer microlayer fims consisting of 32 layers, 50:50 ratio PET to PVDF films were also studied extensively using thermal heat setting technique. Samples with good thickness uniformity after stretching were selected for these experiments, and offline characterization techniques were applied to study morphology. Films were annealed at temperatures around PVDF melting peak, which caused transformation of PVDF polymorphs from primarily alpha to combined gamma and/or gamma' forms. When oriented at 150^oC to 1.5X1, and ' -PVDF were detected in small amounts (via DSC) after annealing at 172^oC, and only ' after higher temperature annealing. Stretching at 150^oC to higher strains produced high amounts of '-PVDF only when annealed at 155^oC for films stretched to 3.5X1, and annealed at 150^oC for films stretched to 2.5X1. Offline characterization led to development of a structural model for PVDF layers alone, by de-laminating film layers. Then, morphology was correlated with dielectric properties by testing lms at room temperature, and at constant frequency, in temperature ramping experiments. Temperature ramping dielectric experiments showed that high percent crystallinity of PET may also help improve loss behavior at high temperatures. Furthermore, samples containing gamma and/or gamma'-PVDF had increasing dielectric constant with increasing temperature, however dielectric loss also greatly increased with increasing temperature. A significant conclusion was that the annealed sample without gamma or gamma'-PVDF present had only a slightly lower dielectric constant at high temperature testing, but also had much lower loss, making it a potential candidate for high temperature capacitor applications.</div><div><br></div><div>Other materials for potential dielectric film applications were studied as well. Two fluoropolymer films consisting of monolayers of ETFE and THV were uniaxially oriented and their morphology was characterized offline to elucidate structure-process-property relationships. Film samples produced were not large enough to be tested for dielectric properties, however morphology development during uniaxial orientation was evaluated. Both films showed nearly affine stretching behavior, and mechano-optical properties were studied during stretching at several temperatures. Combinations of X-ray scattering experiments and AFM led to proposed morphological structure models for each material at varying levels of deformation.</div><div><br></div><div>Finally, in collaboration with A. Schulman, Inc., PET and EVOH compounded blend and three layer PET-EVOH-PET films were oriented uniaxially and the morphology of the two was compared to each other. Potential applications include high barrier food packaging applications, due to the very high oxygen barrier but poor water vapor barrier of EVOH, which can be complimented by PET's high water vapor barrier. Uniaxial orientation of these two film systems showed that mechano-optical behavior was significantly different for blend versus layered films. Crystalline orientation factors were calculated from 1D WAXS data, which showed PET orientation was largely unaffected by increasing EVOH content in blend films, but blending decreased orientation of EVOH. PET's orientation in layered films was also largely unaffected by amount of EVOH in inner layer. EVOH's orientation factor was higher in all layered film compositions compared to neat EVOH film after stretching, suggesting that the coextrusion process is beneficial to increasing orientation of EVOH.</div><div><br></div>

The bacterial meningitis caused by Neisseria meningitidis is responsible for considerable morbidity and mortality throughout the world. Given the limitations of existing diagnostic tests and the severity of the illness associated with the disease, there is a clear requirement for a rapid and specific diagnostic assay. This thesis describes the development of nanoparticle based tests for the detection of Neisseria meningitidis specific cell surface markers. As an initial target antigen, a recombinant form of highly conserved outer membrane protein, OMP85 was used. Within the OMP85 protein sequence, a predicted antigenic sequence between residues 720 and 745 was identified and found to be unique to this organism. This amino acid sequence was synthesised as peptide (SR1) with a gly-gly-cysteine spacer sequence at the N-terminus using t-boc chemistry. Also, the major virulence factor, capsular polysaccharide of N. meningitidis serogroup B bacteria was purified. Polyclonal antibodies were raised against purified OMP85 antigen in rabbits and against SR1 peptide and also against formalin inactivated N. meningitidis serogroup B whole cell bacteria in sheep. This panel of different antibodies including the commercial anti-capsular monoclonal antibodies were examined for cross reactivity against a range of closely related Gram negative bacteria. Based on these cross-reactivity studies, a highly specific anti-NM antibody was developed following purification of the anti-SR1 antiserum by immuno-affinity chromatography. Purified OMP85 antigen and anti-OMP85 antibody were successfully conjugated on 13, 30, 40, 50 and 60 nm gold nanoparticles by an electrostatic adsorption method. Coupling of the gold nanoparticles results in a shift of the respective surface plasmon peak toward longer wavelengths (in the range of 600-800 nm) resulting in a change of the colour of the colloidal suspension from red to purple to blue. An attempt was made to develop a rapid diagnostic assay based on gold nanoparticle induced colour shift assay for N. meningitidis by utilising the specific interaction of OMP85 and anti-OMP85 antibody conjugated to gold nanoparticles as a model system. However, this system was not reproducible and is likely to be due to problems with stability of gold nanoparticles during the conjugation process. As an alternative approach, a highly selective quartz crystal microbalance (QCM)-based immunosensor was designed using the same OMP85/anti-OMP85 antibody system. A method was developed using polyvinylidene fluoride (PVDF) coated QCM crystals with protein A for the directional orientation of the antibodies. To further enhance the sensitivity of the test, OMP85-conjugated gold nanoparticles were used as signal amplification probes for the reproducible detection of the target down to 300 ng/mL, corresponding to a five fold increase in sensitivity compared to detection of OMP85 antigen alone. Also, this sensor has successfully been employed to detect whole cell bacteria at a concentration as low as 100 cfu/mL. Thus, in this study using the real-time QCM measurements, a novel strategy has been developed for the sensitive detection of both N. meningitidis bacteria and the protein antigen at very low concentrations, using gold nanoparticles as signal amplification probes.

Un mélange de Kynar-PVDF et de l'acide poly(2-acrylamido-2-méthyl-1-propane sulfonique) (PAMPS) est envisagé comme matériau de membrane pour pile à combustible. Le mélange est réalisé en solution dans le diméthylformamide et la membrane est obtenue après évaporation du solvant à différentes températures.<br />Les solubilités en solution du polyélectrolyte puis du mélange sont étudiées. Les morphologies des membranes et la cristallinité du Kynar sont ensuite caractérisées. Un comportement de type LCST est mis en évidence. L'utilisation de contre-ions tétrabutylammonium (TBA) permet d'obtenir des mélanges miscibles. Le TBA est ensuite échangé, la forme acide du PAMPS étant nécessaire au fonctionnement en pile. La perméabilité à l'eau et la conductivité ionique sont enfin caractérisées. Une nanostructuration de type bicontinu est particulièrement efficace pour l'application envisagée. Pour stabiliser cette morphologie, un copolymère polyélectrolyte réticulable est synthétisé.

L'ingénierie tissulaire vise à réparer les tissus endommagés et à récupérer les fonctions biologiques correspondantes. Afin de restaurer un tissu endommagé tel que le système nerveux, la conception et la fabrication de nouveaux types d'échafaudages tissulaires sont nécessaires. Dans ce travail, nous avons développé plusieurs techniques de microfabrication pour le polyfluorure de vinylidène (PVDF), un fluoropolymère thermoplastique, non réactif et piézoélectrique, qui peut être utilisé pour la culture cellulaire et l'ingénierie tissulaire. Nous avons tout d'abord étudié l'adhésion et la croissance cellulaire sur des substrats en PVDF avec des motifs micro et nanométriques en utilisant différentes techniques de fabrication telles que la micro-photolithographie, la lithographie douce, l'impression par microcontact, etc. L'influence de la micro-structuration sur les activités piézo-électriques du PVDF a été caractérisée par différentes méthodes d'analyses de surface (FTIR, XRD). Par la suite, nous avons effectué une étude systématique sur la fabrication de nanofibres de PVDF et leur compatibilité avec la culture cellulaire. Enfin, nous avons démontré la possibilité de doper ces nanofibres avec des nanoparticules magnétiques ce qui les rends excitables à distance par un champ magnétique.

Analytical force and dynamic models for material removal processes such as end and face milling do not account for material and process related uncertainties such as tool wear, tool breakage and material inhomogeneity. Optimization of material removal processes thus requires not only optimal process planning using analytical models but also on-line monitoring of the process so that adjustments, if needed, can be initiated to maximize the productivity or to avoid damaging expensive parts. In this thesis, a Polyvinylidene Fluoride (PVDF) sensor based process monitoring method that is independent of the cutting conditions and workpiece material is developed for measuring the cutting forces and/or torque in milling. The research includes the development of methods and hardware for wireless acquisition of time-varying strain signals from PVDF sensor-instrumented milling tools rotating at high speeds and transformation of the strains into the measurand of interest using quantitative physics-based models of the measurement system. Very good agreement between the measurements from the low cost PVDF sensors and the current industry standard, piezoelectric dynamometer, has been achieved. Three PVDF sensor rosettes are proposed for measuring various strain components of interest and are shown to outperform their metal foil strain gauge counterparts with significantly higher sensitivity and signal to noise ratio. In addition, a computationally efficient algorithm for milling chatter recognition that can adapt to different cutting conditions and workpiece geometry variations based on the measured cutting forces/torque signals is proposed and evaluated. A novel complex exponential model based chatter frequency estimation algorithm is also developed and validated. The chatter detection algorithm can detect chatter before chatter marks appear on the workpiece and the chatter frequency estimation algorithm is shown to capture the chatter frequency with the same accuracy as the Fast Fourier Transform (FFT). The computational cost of the chatter detection algorithm increases linearly with data size and the chatter frequency estimation algorithm, with properly chosen parameters, is shown to perform 10 times faster than the FFT. Both the cutting forces/torque measurement methodology and the chatter detection algorithm have great potential for shop floor application. The cutting forces/torque measurement system can be integrated with adaptive feedback controllers for process optimization and can also be extended to the measurement of other physical phenomena.

<p>Regenerative medicine holds the promise of providing relief for people suffering from diseases where treatment has been unattainable. The research is advancing rapidly; however, there are still many hurdles to overcome before the therapeutic potential of regenerative medicine and cell therapy can be realized. Low in frequency in all tissues, stem cell number is often a limiting factor. Approaches that can control the proliferation and direct the differentiation of stem cells would significantly impact the field. Developing an adequate environment that mimics in vivo conditions is an intensively studied topic for this purpose. Collaboratively, researchers have come close to incorporating nearly all biological cues representative of the human body. Arguably the most overlooked aspect is the influence of electrical stimulation. In this dissertation, we examined polyvinylidene fluoride (PVDF) as a new biomaterial and developed a 3D scaffold capable of providing mechanical and electrical stimuli to cells in vitro. </p><p>The fabrication of a 3D scaffold was performed using electrospinning. To obtain highly aligned fibers and scaffolds with controlled porosity, the set-up was modified by incorporating an auxiliary electrode to focus the electric field. Highly aligned fibers with diameters ranging from 500 nm to 15 µm were fabricated from colorless polyimide (CP2) and polyglycolic acid (PGA) and used to construct multilayer scaffolds. This experimental set-up was used to electrospin &#945;-phase PVDF into the polar &#946;-phase. We demonstrated the transition to the &#946;-phase by examining the crystalline structure using x-ray diffraction (XRD), differential scanning calorimetry (DSC), fourier transform infrared spectroscopy (FTIR) and polarized light optical microscopy (PLOM). We confirmed these results by observing a polarization peak at 80°C using the thermally stimulated current (TSC) method. Our results proved the electrospinning process used in our investigation poled the PVDF polymer in situ. </p><p>TThe influence of architecture and topographical cues was examined on 3D scaffolds and films of CP2 polyimide and PVDF. Culture of human mesenchymal stem cells (hMSCs) for 7 and 14 days demonstrated a significant difference in gene expression. The fibers upregulated the neuronal marker microtubule associated protein (MAP2), while downregulation of this protein was observed on films. Gap junction formation was observed by the expression of connexin-43 after 7 days on PVDF films attributed to its inherent pyroelectric properties. Connexin-43 expression on fibers showed cell-cell contact across the fibers indicating good communication in our 3D scaffold. </p><p>A scaffold platform was designed using PVDF fibers that allowed us to apply electrical stimulation to the cells through the fibers. The electrically stimulated PVDF fibers resulted in enhanced proliferation compared to TCPS as evidenced by a 10% increase in the uptake of EdU. Protein expression revealed upregulation of neuronal marker MAP2. Our findings indicate this new platform capable of delivering mechanical, electrical, topographical and biochemical stimuli during in vitro culture holds promise for the advancement of stem cell differentiation and tissue engineering.</p> / Dissertation

In this study, with near-field electrospinning technique of PVDF (Polyvinylidene fluoride) piezoelectric nano-fibers and the additional multiwalled-carbon nanotubes(MWCNT), both mechanical strength and piezoelectric characteristics of a single nano-fiber were discussed. Then the behavior of piezoelectric fiber actuators was realized using inverse piezoelectric effect. Near-field electrostatic technology can be used to fabricate PVDF piezoelectric fibers with an excellent piezoelectric property compared with film structures due to a higher piezoelectric coefficient and energy conversion efficiency. It is more suitable to produce micro transducers. By adjusting velocity of a fully parametric x-y stage, DC voltage, and the distance between the needle and collection plate, the morphology and polarization intensity of piezoelectric fiber can fully be controlled. In addition, the optimal parameters of PVDF solution such as PVDF powder weight percentage and MWCNT were also discussed. From the observation of XRD (X-ray diffraction), it reveals a high diffraction peak at 2£c=20.8¢X of piezoelectric crystal £]-phase structure. Finally, the actuation property was tested using DC voltage supply, and fiber has significant deflection in the experiment. The vertical deflection can be observed and compared with model solution of piezoelectric cantilever structure. In the fiber¡¦s direct piezoelectric effect, the result shows that fiber can produce an open circuit voltage of 15mV under a low frequency vibration of 7Hz.

This study used electrospinning to fabricate a polyvinylidene fluoride (PVDF) piezoelectric nanofiber harvesting device with interdigitated electrode to capture ambient energy. According to d33 mechanical-electric energy conversion mode, the energy harvesting device can be applied on the low frequency ambient vibration and impact abilities for the transformation mechanical energy into electrical energy effectively. First, the PVDF powder was mixed in acetone solution uniformly and the dimethyl sulfoxide (DMSO) was mixed with multi-walled carbon nanotube (MWCNT) to prepare PVDF macromolecular solution. The mixed solution was filled in a metals needle injector and contacted hundreds of voltage. After the PVDF drop in the needle was subjected to high electric field, the drop overcame surface tension of the solution itself, then extremely fine PVDF fiber was formed and spun out. The electrospun was collected orderly using X-Y digital control stage and the linear diameter of electrospun can be controlled easily by adjusting the travelling speed of the stage. In the spinning process, as affected by stretching strain and electric field at the same time, the PVDF piezoelectric fiber resulted in electric polarization and transformed £] piezoelectric crystal phase, in which the dipoles are oriented in the same direction. Furthermore, MWCNT was added to improve the mechanical properties of fiber and increase £] phase, to enhance the tensile strength and piezoelectric property of PVDF fiber effectively. Finally, the photolithography was used to fabricate interdigitated electrodes with 100£gm gap on the flexible PI substrate. The PVDF fibers, with a length and diameter of approximately 1cm and 700-1000nm, were aligned on interdigitated electrodes and packaged with the PI film. In order to increase the conversion efficiency of piezoelectric fiber in d33 mode, the PVDF fibers were repolarized in a high electric field. The results showed that the PVDF fiber energy harvesting device can generate 15mV open-circuit voltage under low frequency vibration of 4Hz and generate above 30mV open-circuit voltage under 6Hz vibrations. As compared with the piezoelectric fiber not repolarized by interdigitated electrode, its output voltage was increased by1- 2 times.