Spelling suggestions: "subject:"[een] COATING"" "subject:"[enn] COATING""
231 |
Air entrainment in angled dip coatingCohu, O., Benkreira, Hadj January 1998 (has links)
Yes / The coating flow examined here, labelled angled dip coating, is that where a substrate enters a pool of liquid forming an angle ß with the vertical so that it intersects the liquid along a wetting line which is not perpendicular to the direction of its motion. This flow situation is distinctly different from that where the substrate, inclined in the other dimension by the so-called angle of entry ¿, intersects the liquid surface perpendicularly to its motion. Experiments were carried out with various liquids to determine the effect of ß on the substrate velocity at which air is entrained into the liquid. It was observed that as this angle departs from zero, air entrainment is delayed to higher speeds. The data show that the speed which is relevant to air entrainment is not the velocity of the substrate itself but its component normal to the wetting line. This result has important practical implications and suggests that this fundamental principle is also applicable to other coating flows.
|
232 |
Slot Coating Minimum Film Thickness in Air and in Rarefied HeliumBenkreira, Hadj, Ikin, J. Bruce 30 April 2016 (has links)
Yes / This study assesses experimentally the role of gas viscosity in controlling the minimum film thickness in slot coating in both the slot over roll and tensioned web modes. The minimum film thickness here is defined with respect to the onset of air entrainment rather than rivulets, the reason being that rivulets are an extreme form of instabilities occurring at much higher speeds. The gas viscosity effects are simulated experimentally by encasing the coaters in a sealed gas chamber in which various gases can be admitted. An appropriate choice of two gases was used to compare performances: air at atmospheric pressure and helium at sub-ambient pressure (25mbar), which we establish has a significantly lower “thin film” viscosity than atmospheric air. A capacitance sensor was used to continuously measure the film thickness on the web, which was ramped up in speed at a fixed acceleration whilst visualizations of the film stability were recorded through a viewing port in the chamber. The data collected show clearly that by coating in rarefied helium rather that atmospheric air we can reduce the minimum film thickness or air/gas entrainment low-flow limit. We attribute this widening of the stable coating window to the enhancement of dynamic wetting that results when the thin film gas viscosity is reduced. These results have evident practical significance for slot coating, the coating method of choice in many new technological applications, but it is their fundamental merit which is new and one that should be followed with further data and theoretical underpinning.
|
233 |
Electrifying the Molecules of Life : Peptide and Protein Analysis by Capillary Electrophoresis Coupled to Electrospray Ionization Mass SpectrometryWetterhall, Magnus January 2004 (has links)
<p>This thesis describes the current status and novel aspects of the analysis of the molecules of life, i.e. peptides and proteins, using capillary electrophoresis (CE) coupled to mass spectrometry (MS) via (sheathless) electrospray ionization (ESI). Early reports of sheathless CE-ESI-MS were plagued by limited lifetimes of the electrospray emitter. In this thesis, two new approaches, the Black Dust and the Black Jack methods, utilizing polymer-embedded graphite instead of noble metals are presented. These emitters have shown improved long-term stability and proven excellent for sheathless electrospray operation. Failure of an emitter is often caused by electrochemical reactions occurring at the emitter-liquid interface. The electrochemical properties of the graphite coated emitters were therefore evaluated by classical electrochemical methods, such as cyclic voltammetry and chronoamperometry. The graphite coated emitters showed excellent electrochemical stability and properties compared to noble metal and polymer configurations.</p><p>Analyte-wall interactions have long been known to cause problems in the CE analysis of biomolecules. This can be circumvented by internal modification of the capillary walls. Additionally, it is of outermost importance to have a stable and sufficiently high electroosmotic flow (EOF) to sustain the electrospray, when using a sheathless approach. New monomer and polymer coatings are presented for rapid and high-efficient CE-ESI-MS separations of peptides and proteins.</p><p>Furthermore, the use of CE-ESI coupled to Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) shows great potential for rapid proteomic probing of human cerebrospinal fluid. The results are comparable with more established techniques, such as liquid chromatography and two-dimensional gel electrophoresis coupled to MS. However, the CE-ESI-FTICRMS analysis has significantly lower sample consumption and faster analysis time compared to the other techniques. The applications and use of CE-ESI-MS is expected to have a bright future with continued growth as current trends of multidimensional hyphenation and microfabricated devices are further developed and explored.</p>
|
234 |
Electrifying the Molecules of Life : Peptide and Protein Analysis by Capillary Electrophoresis Coupled to Electrospray Ionization Mass SpectrometryWetterhall, Magnus January 2004 (has links)
This thesis describes the current status and novel aspects of the analysis of the molecules of life, i.e. peptides and proteins, using capillary electrophoresis (CE) coupled to mass spectrometry (MS) via (sheathless) electrospray ionization (ESI). Early reports of sheathless CE-ESI-MS were plagued by limited lifetimes of the electrospray emitter. In this thesis, two new approaches, the Black Dust and the Black Jack methods, utilizing polymer-embedded graphite instead of noble metals are presented. These emitters have shown improved long-term stability and proven excellent for sheathless electrospray operation. Failure of an emitter is often caused by electrochemical reactions occurring at the emitter-liquid interface. The electrochemical properties of the graphite coated emitters were therefore evaluated by classical electrochemical methods, such as cyclic voltammetry and chronoamperometry. The graphite coated emitters showed excellent electrochemical stability and properties compared to noble metal and polymer configurations. Analyte-wall interactions have long been known to cause problems in the CE analysis of biomolecules. This can be circumvented by internal modification of the capillary walls. Additionally, it is of outermost importance to have a stable and sufficiently high electroosmotic flow (EOF) to sustain the electrospray, when using a sheathless approach. New monomer and polymer coatings are presented for rapid and high-efficient CE-ESI-MS separations of peptides and proteins. Furthermore, the use of CE-ESI coupled to Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) shows great potential for rapid proteomic probing of human cerebrospinal fluid. The results are comparable with more established techniques, such as liquid chromatography and two-dimensional gel electrophoresis coupled to MS. However, the CE-ESI-FTICRMS analysis has significantly lower sample consumption and faster analysis time compared to the other techniques. The applications and use of CE-ESI-MS is expected to have a bright future with continued growth as current trends of multidimensional hyphenation and microfabricated devices are further developed and explored.
|
235 |
Élaboration d’un revêtement dense et protecteur sur polycarbonate / Synthesis of a dense and protective coating on polycarbonateLionti, Krystelle 21 November 2012 (has links)
Ce travail s’intéresse a la synthèse et à la caractérisation de revêtements hybrides O/I à base de silice, préparés par voie sol-gel et déposés sur polycarbonate (PC), pour des applications en milieu chaud et humide dans le domaine culinaire. Le PC étant connu pour sa sensibilité à l’hydrolyse dans ce type de milieux (provoquant sa dépolymérisation progressive et ainsi la libération de bisphénol A, molécule suspectée comme étant toxique), le rôle du revêtement est donc de protéger le PC et d’éviter son vieillissement prématuré, tout en améliorant ses propriétés mécaniques. Dans un premier temps, de nombreux sols ont été synthétisés et optimisés, principalement en termes de nature et quantités de précurseurs, et de pH, dans le but d’obtenir des revêtements homogènes et transparents. Un suivi des réactions d’hydrolyse et de condensation des sols a également été réalisé afin de déterminer le temps minimal de maturation de ces derniers. Apres dépôt des revêtements par dip-coating, les propriétés mécaniques des films ont été étudiées par de nombreuses techniques. D’un point de vue général, les propriétés des échantillons revêtus ont été trouvées supérieures à celles du PC nu. L’influence de nombreux paramètres de synthèse comme le ratio organoalcoxysilane(s)/silice colloïdale, l’ajout d’additifs, le type de traitement de surface du PC pré-dépôt ou encore les conditions de recuit, a également été étudiée. L’ensemble de ce travail a permis d’obtenir, à partir de deux systèmes sol-gel différents, des revêtements performants en termes de transparence, d’adhésion au substrat, de non-toxicité, couplés à des valeurs élevées de dureté, de densité et de module de Young / This work deals with the synthesis and the characterization of hybrid O/I silica coatings prepared by the sol-gel route and deposited on polycarbonate (PC), for applications in hot and humid environment in the alimentary field. PC is well-known for undergoing hydrolysis in such conditions (causing its progressive depolymerization and thus leading to the release of bisphenol A, a molecule suspected to be toxic): the function of the coating would thus consist in preventing PC from this kind of premature ageing, along with the enhancement of its mechanical properties. As a first step, a lot of different sols were synthesized and optimized, mainly in terms of type and quantity of precursors, along with the pH, in order to obtain transparent and homogeneous coatings. The hydrolysis and condensation reactions were monitored in order to determine the minimum ageing time to be waited before any film deposition. After deposition by dip-coating, the mechanical properties of the films were assessed by using many different techniques. Basically, the coated-PC samples display higher properties than the uncoated one. The influence of numerous synthesis parameters such as the organoalkoxysilanes/colloidal silica ratio, the presence of additives, the kind of surface treatment of PC before film deposition, or the annealing conditions was also studied. This whole work led to the synthesis, from two different sol-gel systems, of superior quality coatings in terms of transparency, adherence to the substrate, non-toxicity, along with elevated hardness, density and Young’s modulus values
|
236 |
Variations Related to Print Mottle in Starch-Containing Paper CoatingsRagnarsson, Micael January 2012 (has links)
Starch in paper coatings is known to increase the risk of print mottle in lithographic offset printing. The objective of this study was to increase the understanding of this behaviour. Four phenomena that could lead to print mottle, where the presence of starch might be important, have been identified: uneven binder migration, uneven coating mass distribution, uneven deformation during calendering and differential shrinkage. The latter three were investigated in this project. Starch-containing coating colours often have high water retention. A relationship between the water retention of the coating colours and the distribution of coating thickness was found in a pilot trial. A theory is proposed, where the surface profile of the base paper beneath the blade, that governs the coat weight distribution in blade coating, is affected by moisture from the dewatering coating colours and the compressive force exerted by the blade. Drying strategies were studied to see whether they would induce porosity variations in the coating layers. There is a strong connection between the rate of evaporation and the shrinkage of the coating layer, but no porosity variations due to the choice of drying strategy were found. Shrinkage is governed by the capillary forces. At the same capillary pressure, the coating shrinks more for some binder systems, which is suggested to be due to a weaker chemical interaction between the binder and the pigment. Oxidized starch/latex coatings, stained with a fluorescent marker, had a greater standard deviation in fluorescence intensity than CMC/latex coatings caused by a difference in either porosity or latex distribution. It was shown that calendering introduces porosity variations into the coating layer that are larger for starch-containing coatings. The drying strategies appeared to have a significant effect on these porosity variations and they correlated positively with print mottle in some cases and in another case negatively. In the case of the negatively correlated, the mottle was probably caused by variations in surface porosity existing prior to the calendering.
|
237 |
Korozní a chemická odolnost konverzních povlaků / Corrosion and Chemical Resistance of Conversion CoatingsPalková, Michaela January 2013 (has links)
The purpose of the thesis was to study chemical and corrosion resistance of selected conversion coatings. The corrosion and the possibilities of corrosion protection with focus on conversion coatings on aluminum and steel surface were described in the theoretical part. In the experimental part corrosion and chemical resistance of samples without the next treatment and samples with polyester powder coating and synthetic coating were tested.
|
238 |
Positive release of hot-dip galvanised automotive material to prevent coating adhesion failure at customerMarsland, Wayne Edmund January 2013 (has links)
No description available.
|
239 |
Energy efficiency improvement by the application of nanostructured coatings on axial piston pump slippersRizzo, Giuseppe, Bonanno, Antonino, Massarotti, Giorgio Paolo, Pastorello, Luca, Raimondo, Mariarosa, Veronesi, Federico, Blosi, Magda 02 May 2016 (has links) (PDF)
Axial piston pumps and motors are widely used in heavy-duty applications and play a fundamental role in hydrostatic and power split drives. The mechanical power losses in hydraulic piston pumps come from the friction between parts in relative motion. The improvement, albeit marginal, in overall efficiency of these components may significantly impact the global efficiency of the machine. The friction between slipper and swash plate is a functional key in an axial piston pump, especially when the pump (at low rotational speed or at partial displacement) works in the critical areas where the efficiency is low.
The application of special surface treatments have been exploited in pioneering works in the past, trying different surface finishing or adding ceramic or heterogeneous metallic layers. The potential of structured coatings at nanoscale, with superhydrophobic and oleophobic characteristics, has never been exploited. Due to the difficulty to reproduce the real working conditions of axial piston pump slippers, it has been made a hydraulic test bench properly designed in order to compare the performance of nano-coated slippers with respect to standard ones. The nano-coated and standard slippers have been subjected to the following working conditions: a test at variable pressure and constant rotational speed, a test at constant pressure and variable rotational speed. The comparison between standard and nanocoated slippers, for both working conditions, shows clearly that more than 20% of friction reduction can be achieved using the proposed nano-coating methodology.
|
240 |
Adhesion of CVD coatings on new cemeted carbides / Vidhäftning mellan keramiskt skikt och hårdmetall med alternativ bindefasBojestig, Eric January 2016 (has links)
Steel turning inserts cemented carbides have a binder phase consisting of cobalt (Co). However, in recent years a study from the United States National Toxicity Program (NTP) found that cobalt powder is carcinogenic upon inhalation. The European Union's REACH have therefore also classified cobalt powder as carcinogenic upon inhalation. The worldwide search to find a replacement has therefore lately intensified. It is important that the alternative binder phase has no negative effects on the properties of the insert. In this thesis the adhesion between a multilayer ceramic chemical vapor deposition (CVD) coating and a cemented carbide with the alternative binder phases consisting of iron (Fe), nickel (Ni) and cobalt (Co) has been studied. First of all, the fracture surfaces showed that the CVD coating was able to grow on all cemented carbides, regardless of which binder phase. To evaluate the adhesion, scratch tests were performed on all samples. The results from the scratch tests were not as expected. No chipping of the coating down to the cemented carbide occurred on any of the samples and the samples with the hardest cemented carbide did not get the highest critical load, which it should according to the literature if all other parameters were the same. Instead the sample with the binder phase consisting of 73 wt% iron and 27 wt% nickel had the highest critical load. This is thought to be due to that during the scratch test the binder phase in this cemented carbide would most likely transform into deformation martensite.
|
Page generated in 0.0695 seconds