An electrochemical double-layer capacitor (EDLC) is a potential buffer for current power and energy supply. In this work, activated carbon derived from fluid coke as a brand new electrode material was studied due to its high specific surface area (SSA) and large portion of mesopores. A suitable electrode material formula, current collector, and cell configuration were investigated to fabricate a testable system and ensure the reproducibility of measurements. Cyclic voltammetry (CV) and constant current charge/discharge (CD) techniques were used to characterize the performance of the electrode material, as well as to study its fundamental behaviour. A new procedure was established for quantifying the capacitance (Cc) of EDLC from CV which isolates the effect of internal resistance on the measured capacitance (CM). The specific capacitance of single electrode made of activated carbon (~1900 m2/g) with approximately 80% mesopores and macropores was able to reach 180 F/g at scan rate of 0.5mV/s.

This thesis presents thermodynamic studies performed by electrochemical methods (cyclic voltammetry, electrochemical impedance and chronopotenciometry) in three of the most important electrochromic materials: a-WO3, conducting polymers and viologens. Electrochromic materials are very promising as a low-consuming technology. By incorporating these materials in windows of buildings or vehicles, approximately a 30% of the consumed energy in these systems can be saved.Regarding the a-WO3, apart from other contributions, a new model based on lattice distortions, able to explain the intercalation thermodynamic in this material, is proposed. In the conducting polymers field, a Gaussian energy distribution is proved to account for the initial part of the so broad oxidation peaks observed in cyclic voltammetry. Finally, the coloration kinetics of the viologen modified n-TiO2 electrode is explained.

Electrochemical detection of metals can be done at polycrystalline gold ultramicroelectrodes using repetitive cyclic voltammetry (RCV), a detection method sharing some similarities with anodic stripping voltammetry (ASV). Each cycle of the potential waveform for RCV involves application of a negative preconcentration potential (for 50 to 300 ms) followed by a cyclic voltammetry (CV) scan at 20 to 1000 V/s. The response due to the metals is evident at potentials negative of the region for oxide formation in the resulting CVs. Metals are deposited at the Au surface by underpotential deposition (UPD) processes. Any metal that can be analyzed by RCV could potentially be quantified using UPD-ASV at Au (rather than by ASV at Hg). The UPD kinetics of Pb and Cu at polycrystalline Au were examined by setting kinetic parameters (rate constant, symmetry factor, and electrosorption valency) within a simulation program used to generate simulated CVs. Reasonably good agreement between experimental and simulated CVs was possible using the simulation, with the same kinetic parameters used to generate simulated CVs to match experimental CVs over a range of sweep rates for each system. Using this method, the following rate constants (k) were estimated: for UPD of Cu in H2SO4 and HClO4, ks ~ 36000 s−1 and 11000 s−1, respectively, and for UPD of Pb in H2SO4, ks ~ 400000 s−1. <p> Repetitive cyclic voltammetry was applied to the detection of metals separated by capillary electrophoresis. Separation of Tl+, Cd2+, Cu2+, Pb2+, Zn2+, Ni2+, Co2+ and Mn2+ was demonstrated in 0.01 mol/L acetic acid and 0.01 mol/L ammonium acetate(pH ~ 4.6) using RCV. While stacking is commonly exploited for sensitivity enhancement during injection, it was shown that detection-end stacking is also useful. A novel technique named electrophoretic extraction (EE) was developed for analysis of particle-containing solutions (e.g. soil extracts or other colloidal suspensions). EE involves application of backpressure during CE to prevent particles from entering the separation capillary: the applied pressure is regulated so analyte ions enter the capillary and migrate to the detector, whereas other particles are prevented from entering the capillary. The feasibility of this approach was demonstrated.

This research is to synthesize PANI (polyaniline) thin film for polymer organic solar cells as a hole transport layer on the top of ITO substrate by using electrochemical (cyclic voltammetry) method. The device structure is ITO (150 nm) / PANI (50 nm) / P3HT: PCBM (100 nm) / Al (200 nm). We investigated surface morphology, conductivity, and light transmission of the PANI thin film from different aniline monomer concentration and studied the factors on device efficiency, also compared with the device structured with hole transport layer PEDOT:PSS. In this study, we found PANI thin films synthesized with different aniline monomer concentration, their light transmission over 80% at the range of 450 nm ~ 650nm wavelength and the conductivity up to 0.6 S/cm. It shows that PANI thin film suitably act as hole transport layer. In addition, we found morphology of PANI thin film that varied with different aniline monomer concentration. The power conversion efficiency of the device mainly affected by morphology with different aniline monomer concentration. Comparing to other parameters of concentration, the 0.3M aniline monomer concentration polymerized PANI thin film owned the most appropriate surface morphology, and the power conversion efficiency up to 1.76%.

Verapamil is a commonly used medicine for the treatment of supraventricular arrhythmias, angina and hypertension. Recently, some newly developed applications of Verapamil, such as treating hypomania and chemotherapy for cancers, have been reported. Thus, monitoring the concentration of Verapamil accurately is very important. The major clinical analytical methods of Verapamil concentration determination are high performance liquid chromatography (HPLC) with UV or with fluorescence detector. However, these analytical methods have some disadvantages, like expensive instruments, complex operation, and time-consuming etc. The chemical structure and properties of Verapamil are very stable. The preliminary result of electrochemical analysis doesn¡¦t show any electrochemical activity. In this study, we developed an innovative ozone pre-treatment method to oxidize Verapamil to the smaller molecules and change its structure. Verapamil have excellent electrochemical activity after ozone pre-treatment. The spectroscopy and mass spectrometry show the changes of Verapamil structure. The products of Verapamil treated with ozone are also predicted by mass spectrometry. The gold nanoelectrode ensemble electrodes (GNEE) are used as working electrode for its good catalytic activity of electrochemical reaction, high sensitivity and high selectivity. The overall experimental framework of this study is microchip with GNEE working electrode accompanied by cyclic voltammetry, an electrochemical analytical instrument. Compared with traditional analytical methods, the system has some advantages such as small size, micro sample volume, easy operation, rapid detection and low cost. The limit concentration of Verapamil solution for stable detection in the system is 10 ng/mL. A linear dynamic range with a high correlation factor from 10 ng/mL to 100 £gg/mL was obtained. For the analysis of serum sample, Verapamil present excellent electrochemical activity at 1 ng/mL. A linear dynamic range with a high correlation factor from 1 ng/mL to 100 £gg/mLwas obtained. According to the results, our system for clinical Verapmil concentration analysis has the feasibility of the practical application.

Fuel cells are the tools which convert chemical energy into electricity directly by the effective utilization of hydrogen and oxygen (or air). One of the most important barriers for the fuel cell commercialization is the durability of the fuel cell components in the long term operations. In this study, the durability of the PEM fuel cell electrocatalysts were investigated via cyclic voltammetry (CV) and rotating disk electrode (RDE) experiments in order to determine the hydrogen oxidation reaction (HOR) and oxygen reduction reaction (ORR) which corresponds to the half cell reactions in the fuel cell. PEM fuel cell electrodes mainly composed of carbon supported Pt catalysts. In long term operations due to Pt dissolution and carbon corrosion some properties of the electrocatalysts can be changed. Performance losses in catalysts mainly depend on / i) decrease in the total metal surface area (SA) and the electrochemically active surface area (ESA) due to the increase in the particle size ii) decrease in the tafel slope potential in ORR and iii) increase in carbon corrosion. In this study, these properties were examined via accelerated degradation tests performed in CV and RDE. The catalysts having different Pt loadings, synthesized with different ink compositions, pH values and microwave durations were investigated. The commercial catalysts having Pt loadings of 20, 50 and 70 (wt %) were tried and best results were obtained for Pt/V (50 wt %) catalyst. Different carbon to Nafion&reg / ratios of 4, 8, 12 in the ink composition were tried. C/N ratio of 8 gave the best result in Pt dissolution and carbon corrosion degradation tests. The catalysts prepared at different pH values of 1.4, 6.25 and 10 were tried and the catalyst prepared at pH of 10 was less degraded in Pt dissolution test and the catalyst prepared at pH of 6.25 showed better resistance to carbon corrosion. Catalysts prepared under different microwave durations of 50, 60 and 120 s were tried and the catalyst prepared at 60 s gave the best performances.

Three illustrative cases involving the electrodeposition of ultrathin metal films of varying reactivities onto noble-metal substrates were investigated: (i) Pd on Pt(111), a noble admetal on a noble-metal surface; (ii) Bi on Pd(111), a less noble admetal on a noble-metal surface; and (iii) Co on polycrystalline Pd and Pd(111), a reactive metal on a noble-metal surface. The interfacial electrochemistry of these prototypical systems was characterized using a combination of electrochemical methods (voltammetry and coulometry) and ultrahigh vacuum electron spectroscopies (Auger electron spectroscopy, AES; low energy electron diffraction, LEED; and X-ray photoelectron spectroscopy, XPS). Potential-controlled adsorption-desorption cycles of aqueous bromide exerted surface smoothening effects on ultrathin Pd films with defect sites (steps). This procedure, dubbed as electrochemical (EC) annealing, constituted a nonthermal analogue to conventional annealing. EC-annealed ultrathin Pd films exhibited long-range surface order and remained free of oxygen adspecies. Pdadatoms occupying step-sites were selectively dissolved and/or rearranged to assume equilibrium positions in a well-ordered (1x1) film. Electrodeposition of Co was found to be highly surface-structuresensitive. While virtually no Co electrodeposition transpired on a clean Pd(111) surface, Co was voltammetrically deposited on (i) a Pd(111) electrode roughened by oxidation-reduction cycles; and (ii) thermally annealed polycrystalline Pd, which is a composite of the (111) and (100) facets. Electrodeposition of Co was also observed to be kinetically hindered and slow potential scan rates (0.1 mV/s) were required. Well-defined ultrathin Bi films were potentiostatically electrodeposited onto Pd(111); a Stranski-Krastanov growth mode was indicated. The electrochemical reactivity of ultrathin Bi films was characterized using two surface probes: aqueous iodide and D-glucose. (i) Exposure of the prepared Bi adlayers (ΘBi 0.33) to aqueous iodide gave rise to (√3x√7) I-on-Bi superlattice. The same superlattice was obtained if Bi was electrodeposited onto Pd(111)(√3x√3)R30o-I. (ii) With respect to electrooxidation of D-glucose on Pd(111), the presence of Bi adlayers inhibited the by-product-induced "surface poisoning" of Pd(111) but reduced its electrocatalytic efficiency.

Eine Reihe 3-(p-X-phenyl)-Thiophenmonomeren (X = -H, -CH3, -OCH3, -COCH3, -COOC2H5, -NO2) wurde elektrochemisch polymerisiert, um Filme zu erhalten, die umkehrbar reduziert und oxidiert werden konnten (n-und p-dotiert wurden). Die Oxidationspotentiale der Monomere und die formalen Potentiale der n und p-Dotierprozesse der Polymere wurden mit Resonanz- und induktiven Effekten der Substituenten (Hammett konstanten) am Phenylring sowie semiempirisch errechneten Bildungswärmen der Monomereradikalkationen korreliert. Außerdem wurden die Oxidationspotentiale mit den Ionisierungspotentialen der Monomere verglichen, die über die Dichtefunktionialtheorie (DFT) errechnet wurden, die der Energie für das Erzeugen der Radikalkationen entsprechen. Um theoretische Grundlagen für die Einstufen-Bildung regioregulär -konjungierter Oligo- und Polythiophene zu erhalten, wurden die elektronischen Zustände von 3-Phenylthiophen-Derivaten anhand von Molekülorbitalberechnungen auf Grundlage der Dichtefunktionaltheorie mit Becke’s Drei-Parameter-Funktion (B3LYP), sowie mit den Basissätzen 6-31G(d) und 3-21G(d) erklärt. Die Reaktivität der Verknüpfung von mono- und oligo-3-Phenylthiophenen wurde von den berechneten ungepaarten Elektronenspindichten der entsprechenden Radikal-Anionen abgeleitet. Die Ionisierungspotentiale, die den Energien zur Erzeugung der Radikal-Anionen während der Oxidation entsprechen, wurden abgeschätzt. Die aus den 3-Phenylthiophenen entstandenen regioselektiven Hauptprodukte können gut durch die Größe der Spindichten erklärt werden. Da die Verknüpfungsreaktion an der zwei-Position des Thiophnrings (C-2) sterisch durch die Phenylgruppe und den Thiophenring gehindert ist, startet die Initiierung der 3-Phenylthiophene über die Bildung eines Kopf-Schwanz-Dimers. Folglich spielt das Kopf-Schwanz-Dimer eine wichtige Rolle bei den Wachstumsreaktionen der 3-Phenylthiophene. Die Ursache dafür liegt darin, dass das Kopf-Schwanz-Dimer in 5-Position die höchste Spin-Dichte besitzt und die Wahrscheinlichkeit einer Kopf-Kopf-Verknüpfung aufgrund der sterischen Hinderung zwischen dem Thiophenring und der Phenylgruppe gering ist. Polymerfilme von 3-Phenylthiophenderivaten, die durch elektrochemische Polymerisation synthetisiert wurden, sind in situ und ex situ durch Resonanz-Raman-Spektroskopie bei verschiedenen Anregungswellenlängen, sowie durch in situ und ex situ UV-Vis Spektroskopie analysiert wurden. Die Entwicklung der in situ UV-Vis-Spektren der Polymer von 3-Phenylthiophene nach der Dotierung wird durch ähnliche Eigenschaften gekennzeichnet, wie für viele Polythiophene mit einem hohen Grad der Konjugation beobachtet. Während der schrittweisen Oxidation der Poly-3-phenylthiophen Filme verringert sich die Intensität der Absorption wegen des Überganges bei 450-566 nm und ein neues ausgedehntes Absorptionsband, das auf (bi)polaron Zustände bezogen wird erscheint bei ungefähr 730-890 nm. Andererseits wird während der Oxidation (p-Dotierung) des Poly3-phenylthiophen Filmes eine blau/hypsochrome Verschiebung für beide Absorptionsbänder beobachtet . Es wird durch die Tatsache erklärt, dass ein Polymer eine Verteilung der Kettenlängen enthält und die längste Polymer kette (dessen Absorption bei niedriger Energie auftritt), bei niedrigeren Potentialen zu oxidieren beginnt. Die elektrochemischen Bandlücken der Derivate von 3-Phenylthiophen sind durch zyklische Voltametrie gemessen worden. Der Effekt der Substituenten auf den Oxidations-/Reduktions- potentiale wird besprochen. Bei Bandlücken, die durch zyklische Voltammetrie erhalten wurden, hat sich herausgestellt, dass sie im Allgemeinen höher liegen als optische Bandlücken. Erste Resultate der in situ Resonanz-Raman-Spektroskopie, von dem elektrochemisch erzeugten Polymerderivate von 3-Phenylthiophen Filmen auf einer Platinelektrode, in einer organischen Elektrolytlösung, werden berichtet. Beobachtete Raman Banden werden zugewiesen; gegründet auf diesen Resultaten werden die zuvor angenommenen molekularen Strukturen diskutiert. / A series of 3-(p-X-phenyl) thiophene monomers (X= –H, –CH3, –OCH3, –COCH3, –COOC2H5, –NO2) was electrochemically polymerized to furnish polymer films that could be reversibly reduced and oxidized (n- and p-doped). The oxidation potentials of the monomers and formal potentials of the n- and p-doping processes of polymers were correlated with resonance and inductive effects (Hammett constants) of the substituents on the phenyl ring as well as the semiempirically calculated heats of formation of the monomer radical cations. Moreover, the oxidation potentials of the monomers were correlated with the ionization potentials of the monomers calculated via density functional theory (DFT), which correspond to the energies for generating radical cations during oxidative processes. For obtaining a theoretical basis for the one-step formation of regioregular –conjugated oligo-and polythiophenes, the electronic states of 3-phenylthiophene derivatives were elucidated by molecular orbital calculations using density functional theory with the Becke-type three parameters functional (B3LYP), the 6-31G(d), and 3-21G(d) basis sets. The reactivity for coupling reaction of mono- and oligo-3-phenylthiophenes are inferred from the calculated unpaired electron spin densities of the respective radical cations, and the ionization potentials which correspond to the energies for generating radical cations during oxidative processes were estimated. The major regioselective products of the oligomerization of 3-phenylthiophene can be well understood in terms of the magnitude of spin densities. Since the steric hindrance between the phenyl group and thiophene ring interferes with the coupling reaction occurring between 2-postions (C–2) of thiophene rings, the initiating reaction of 3-phenylthiophene is generaton of a head-to-tail (HT) dimer. Thus, the head-to-tail (HT) dimer plays an important role in the propagation reactions of 3-phenylthiophene. This originates from the highest spin density at the 5- position of the HT dimer and low probability of the HH coupling due to the steric hindrance between thiophene ring and phenyl group. Polymer films of the 3-phenylthiophene derivatives prepared by electrochemical polymerization were analyzed, in situ and ex situ, with resonance Raman spectroscopy using several excitation wavelengths as well as in situ and ex situ UV-Vis-spectroscopy. The evolution of the in situ UV-Vis-spectra of poly 3-phenylthiophene derivatives upon doping is characterized by similar features as observed for many polythiophenes with high degree of conjugation. During stepwise oxidation of the poly-3-phenylthiophene films the intensity of the absorption due to the transition around 450–566 nm decreases and a new broad absorption band related to (bi)polaron states appears around 730-890 nm. On the other hand, during the oxidation (p-doping) of the poly-3-phenylthiophene films a blue/hypsochromic shift is observed for both absorption bands. It is explained by the fact that a polymer contains a distribution of chain lengths, and the longest polymer chains (the absorption of which occurs at lower energies) start to oxidize at lower potentials. The electrochemical bandgaps of 3-phenylthiophene derivatives have been measured by cyclic voltammetry. The effect of substituents on the oxidation / reduction potentials is discussed. Bandgaps obtained by cyclic voltammetry have been found to be in general higher than optical bandgaps. Preliminary results of in situ resonance Raman spectroscopy of electrochemically generated poly-3-phenylthiophene derivatives films on a platinum electrode exposed to an organic electrolyte solution are reported. Observed Raman bands are assigned; based on these results previously suggested molecular structures are discussed.

In the search for alternative energy technologies, low temperature fuel cells continue to feature as technologies with the most promise for mass commercialization. Among the low temperature fuel cells, alkaline and proton exchange membrane fuel cells are the most popular. Alkaline fuel cells have typically been used for water generation as well as auxiliary power for space shuttles. Their bulkiness however makes them undesirable for other applications, especially in automobiles, where there is a great demand for alternative technologies to internal combustion engines. Proton exchange membrane fuel cells on the other hand possess numerous qualities including their compact size, high efficiency and versatility. Their mass implementation has however been delayed, because of cost among other reasons. Most of this cost is owed to the Pt/C catalyst that accounts for about half of the price of the PEM Fuel Cell. This catalyst is used to drive the sluggish oxygen reduction reaction that occurs at the cathode of the PEM Fuel Cell. To overcome this obstacle, which is to make PEM Fuel Cell technology more affordable, reducing the amount Pt has traditionally been the approach. Another approach has been to find new ideal catalyst-support combinations that increase the intrinsic activity of the supported material. One more strategy has been to find lower cost alternative materials to Pt through synthetic and kinetic manipulations to rival or exceed the current oxygen reduction reaction activity benchmark. To this end, Palladium has garnered significant interest as a monometallic entity. Its manipulation through synthetic chemistry to achieve different morphologies - which favor select lattice planes - in turn promotes the oxygen reduction reaction to different degrees. In bimetallic or, in more recent times multimetallic frameworks, geometric and ligand effects can be used to form ideal compositions and morphologies that are synergistic for improved oxygen reduction reaction kinetics. In this dissertation, we have explored three different approaches to make contributions to the catalysis and electrocatalysis body of literature. In the first instance, we look at the influence of ligand effects through the active incorporation of a PVP capping agent on the stability of ~3nm Pt NPs. Washed (no capping agent) and unwashed (with capping agent) batches of NPs were evaluated via cyclic voltammogram analyses to evaluate differences there might be between them. It was found that the current density measurements for unwashed particle batches were higher. This increase in current density was attributed to the monodentate and bidentate ligand bonding from the PVP, which increased as a function of cycle number and plateaued when the PVP was completely decomposed. The complete decomposition of PVP during the CV experiment was estimated to occur around 200 cycles. The remaining portion of the dissertation explores the electrocatalytic properties of Palladium based NPs. The first instance, a monometallic study of Palladium cubes and dendrites was aimed at building on a recent publication on the enhanced ORR activity that was achieved with a PdPt bimetallic dendrite morphology. In our work, we sought to isolate the dendritic morphology properties of the monometallic Pd composition in order to understand what advantages could be achieved via this morphology. Pd cubes were used as a comparison, since they could be generated through the combination of a similar set of reagents simply by switching the order of addition. It was found that while there was no significant variation in the ORR activity as a function of morphology / shape, there was an interesting interaction between hydrogen and the palladium NPs in the hydrogen oxidation region that varied as a function of shape. This led to further sorption and ethylene hydrogenation studies, which suggested that, the interaction between hydrogen and Pd depended on the environment. Within the electrochemical environment, the ECSA measured, suggested that hydrogen was being reversibly absorbed into the sub-surface octahedral sites of Pd. The higher ECSA for Pd cubes corroborated with higher sorption for Pd cubes as well. However ethylene hydrogenation showed that the fringes of the Pd dendrites provided additional sites for reaction, which in turn translated to higher conversion. Furthermore, through a Koutecky-Levich analysis, it was found out that the Pd dendrites while exhibiting slightly lower activity, favored the 4-electron oxygen reduction process more than the Pd cubes. In the last part of this dissertation we explored the electrocatalytic properties of Pd-based bimetallic NPs under different morphologies including nanocages and sub-10nm alloys. With the inclusion of Ag, it was found out, through Koutecky-Levich analysis that the 4-electron process was better observed under alkaline conditions using a 0.1M NaOH(aq) electrolyte solution instead of a 0.1M HClO4 (aq) for acidic media testing. It was found that, for PdAg nanocage morphologies, where the Pd galvanically replaced the Ag to form cages, the four-electron process was suited to thinner Pd shells. Indeed the average electron numbers measured for Ag nanocubes coated with a 6nm shell was in agreement, within reason of literature values for bulk Ag. However, since the binding energy that both metals have for OH is so close, the potential for contributions to the ORR kinetics in alkaline media by Pd is a potential consideration.

The electrochemical investigation of nickel, copper and silver thin films interfaced with yttria stabilized zirconia (YSZ) solid electrolyte was accomplished to determine their response to polarization in dilute oxygen environments at 350 °C and assess their viability for electrochemical promotion of catalysis (EPOC). Polycrystalline YSZ (8 mol % Y2O3-ZrO2) pellets were synthesized in the lab and films deposited onto them using evaporative physical vapor deposition (PVD). The critical thickness of copper, silver and nickel thin films were foundusing in-situ resistance measurements. Following this, 50 and 100 nm copper and nickel films were studied using solid electrolyte cyclic voltammetry (SECV) to determine their response to polarization. Given that silver thin films at such thicknesses are thermally unstable, a film of 800 nm was used in this study. The materials were found to respond to polarization in different ways, forming oxides according to Wagner and Mott-Cabrera oxidation models.