No description available.

No description available.

No description available.

In this work novel solid-state neutron detectors based on Gallium Nitride (GaN) have been produced and characterized. GaN is a radiation hard semiconductor which is commonly used in commercial optoelectronic devices. The important design consideration for producing GaN-based neutron detectors have been examined, and device simulations performed. Scintillators and p-i-n diode-type neutron detectors have been grown by metalorganic chemical vapor deposition (MOCVD) and characterized. GaN was found to be intrinsically neutron sensitive through the Nitrogen-14 (n, p) reaction. Neutron conversion layers which produce secondary ionizing radiation were also produced and evaluated. GaN scintillator response was found to scale highly linearly with nuclear reactor power, indicating that GaN-based detectors are suitable for use in the nuclear power industry. This work is the first demonstration of using GaN for neutron detection. This is a novel application for a mature semiconductor material. The results presented here provide a proof-of-concept for solid-state GaN-based neutron detectors which offer many potential advantages over the current state-of-the-art, including lower cost, lower power operation, and mechanical robustness. At present Helium-3 proportional counters are the preferred technology for neutron detection, however this isotope is extremely rare, and there is a global shortage. Meanwhile demand for neutron detectors from the nuclear power, particle physics, and homeland security sectors requires development of novel neutron detectors which are which are functional, cost-effective, and deployable.

A wide variety of group III-Nitride-based photonic and electronic devices have opened a new era in the field of semiconductor research in the past ten years. The direct and large bandgap nature, intrinsic high carrier mobility, and the capability of forming heterostructures allow them to dominate photonic and electronic device market such as light emitters, photodiodes, or high-speed/high-power electronic devices. Avalanche photodiodes (APDs) based on group III-Nitrides materials are of interest due to potential capabilities for low dark current densities, high sensitivities and high optical gains in the ultraviolet (UV) spectral region. Wide-bandgap GaN-based APDs are excellent candidates for short-wavelength photodetectors because they have the capability for cut-off wavelengths in the UV spectral region (λ < 290 nm). These intrinsically solar-blind UV APDs will not require filters to operate in the solar-blind spectral regime of λ < 290 nm. For the growth of GaN-based heteroepitaxial layers on lattice-mismatched substrates, a high density of defects is usually introduced during the growth; thereby, causing a device failure by premature microplasma, which has been a major issue for GaN-based APDs. The extensive research on epitaxial growth and optimization of Al_x Ga _1-x N (0 ≤ x ≤ 1) grown on low dislocation density native bulk III-N substrates have brought UV APDs into realization. GaN and AlGaN UV <i> p-i-n </i> APDs demonstrated first and record-high true avalanche gain of > 10,000 and 50, respectively. The large stable optical gains are attributed to the improved crystalline quality of epitaxial layers grown on low dislocation density bulk substrates. GaN <i>p-i-n </i> rectifiers have brought much research interest due to its superior physical properties. The AIN-free full-vertical GaN<i> p-i-n </i> rectifiers on<i> n </i>- type 6H-SiC substrates by employing a conducting AIGaN:Si buffer layer provides the advantages of the reduction of sidewall damage from plasma etching and lower forward resistance due to the reduction of current crowding at the bottom<i> n </i> -type layer. The AlGaN:Si nucleation layer was proven to provide excellent electrical properties while also acting as a good buffer role for subsequent GaN growth. The reverse breakdown voltage for a relatively thin 2.5 μm-thick<i> i </i>-region was found to be over -400V.

This thesis describes the development of III-Nitride materials for light emitting applications. The goals of this research were to create and optimize a green light emitting diode (LED) and laser diode (LD). Metalorganic chemical vapor deposition (MOCVD) was the technique used to grow the epitaxial structures for these devices. The active regions of III-Nitride based LEDs are composed of InₓGa₁₋ₓN, the bandgap of which can be tuned to attain the desired wavelength depending on the percent composition of Indium. An issue with this design is that the optimal growth temperature of InGaN is lower than that of GaN, making the growth temperature of the top p-layers critical to the device performance. Thus, an InGaN:Mg layer was used as the hole injection and p-contact layers for a green led, which can be grown at a lower temperature than GaN:Mg in order to maintain the integrity of the active region. However, the use of InGaN comes with its own set of drawbacks, specifically the formation of V-defects. Several methods were investigated to suppress these defects such as graded p-layers, short period supper lattices, and native GaN substrates. As a result, LEDs emitting at ~532 nm were realized. The epitaxial structure for a III-Nitride LD is more complicated than that of an LED, and so it faces many of the same technical challenges and then some. Strain engineering and defect reduction were the primary focuses of optimization in this study. Superlattice based cladding layers, native GaN substrates, InGaN waveguides, and doping optimization were all utilized to lower the probability of defect formation. This thesis reports on the realization of a 454 nm LD, with higher wavelength devices to follow the same developmental path.

Thesis (Ph.D.)--University of Western Australia, 2006.

No description available.

Gallium Nitride (GaN) and its alloys with InN and AlN, the III-nitrides, are of interest for a variety of high power-high frequency electronics and optoelectronics applications. However, unlike Si and GaAs technology that have been developed on native substrates, III-nitride devices have been developed on non-native substrates such as Si, sapphire and SiC. This is because bulk cheap native III-nitride substrates are unavailable. Among the known substrates, III-nitride technology development on Si is desirable because of its large substrate size and low cost. However, the large lattice and thermal expansion mismatch between the III-nitrides films and Si substrate leads to a high level of dislocations, 1010 cm-2, and tensile stress which results in cracking. For successful integration of crack free and low dislocation density GaN on Si various kinds of transition layer schemes are used that help to incorporate a compressive growth stress to neutralize the tensile thermal mismatch stresses and also to reduce dislocation densities to levels required by devices. These transition schemes, ranging from 400 nm to 7 m, involve the use of graded AlGaN layers, high/low temperature interlayers and superlattices. The aim of the research described in this thesis was a systematic comparison of the different transition layer schemes currently used with the objective of increasing the efficiency of integrating device quality, crack free, low dislocation density, <109 cm-2, GaN with Si. A metal organic chemical vapor deposition equipped with an in-situ stress monitor was used for growth. Transmission electron microscopy was used for quantitative measurement of dislocation density. The research shows, for the first time, that all transition layer optimization depends critically on the Si surface made available for growth of the first AlN layer. It needs to be optimally cleaned such that it is oxide free and smooth. A quantitative TEM comparison of various currently used transition layer schemes shows that while they have interesting mechanistic differences, they are not very different in their dislocation reduction efficiency. All of them yield a final dislocation density in a probe GaN layer of 1-3×109 cm-2. In contrast, a combination of Si doping and compressive growth stress has a synergistic effect on dislocation reduction. A simple 210 nm transition layer based on this understanding, the lowest reported yet, yields GaN layers that are crack free and have lower <1x109 cm-2 dislocation density, than those obtained by the aforementioned more complicated schemes. High electron mobility transistor characteristics performance on the probe GaN layers obtained on these transition layers supports the structural observations above.

published_or_final_version / Physics / Doctoral / Doctor of Philosophy