The charge-carriers of the organic layers are one of the dominant factors to influence the performance of OLEDs. Thus, it is very important to study and understand the charge transporting behaviors in the organic layers of OLED. However, the organic materials show usually to have very high resistivity and very low carrier mobility, and then using general modeling techniques suitable for common semiconductors cannot conveniently simulate that. First, a transporting model of the bilayer organic OLED are proposed in this dissertation, in which model were based on the current-voltage characteristics simulation proposed by Lampert and the continuous equation of current transport. The model contains a description of ohmic contacts, thermal emission and tunneling injection, space charge effects, trap effect, field dependent mobility and recombination processes. In addition, the method of Monte Carlo is a computational technique by using random numbers to compute an approximation to something whose exact value is difficult or impossible to compute, and that is used to simulate the bilayer organic OLED. In this study, a numerical model proposed is successfully applied to describe the characteristics of the bilayer organic light-emitting diode. The model is satisfyingly demonstrated not only for applying to simulate several bilayer devices (1-Naphdata/Alq3¡BTPD/Alq3) reported but also for some devices obtained in our results. Finally, it can be extended to optimize the analysis and fabrication of bilayer devices.

In this dissertation, the electrical characteristics of the interface between the metal cathode and organic layer in OLEDs are detailed investigated. Currently, surveying on the literature, it is limited in understanding the interfacial characteristics and the injection process of electron at interface, therefore the carrier injection phenomena investigated here is still based on the traditionally inorganic semiconductor physics. As a thin LiF layer inserted between the Al and Alq3 layers, the performance of OLED shown a great deal of improvement, such as lowering the driving voltage and increasing the luminescence efficiency. At first, we study how a very thin LiF layer affecting the performance of OLED device, and the feasible mechanisms attributed to this improvements. Then, the further discussion should be focused on the injection model built for the charge at metal/organic interfaces. Finally, the relationship that the injection model related to the variety of LiF layer thickness could be investigated. From the experimental data, the Al/LiF/Alq3 devices with the LiF thickness of 0.5nm have shown the best performance, and the device performance decay as the thickness of LiF layer increased over 0.5nm. In this study, it assumes that the LiF layer just forms an ¡§integrated¡¨ thin insulating film and lowing the charge injection as the layer thickness over 0.5nm, and it also assume that in model derived process is independent on the metal work function. Since the molecular structure of organic materials is quite difference from the valence band structure in inorganic semiconductor materials, it could be assumed no band bending like that the p-n junction at the interface of inorganic semiconductor under thermal equilibrium. After theoretical approach, we get the reasonable results by comparing with the literatures reported recently. The conclusion of this study reveals that the charge injection is independent on the metal work function, but is determined by the interface structure characteristic of interface structure at metal/organic interfaces. Furthermore, in the Al/LiF/Alq3 structure, the chemical reaction is saturated at the interface as the LiF layer forms a ¡§integrated¡¨ thin insulating film. Therefore, the device performance decay is the effect due to the insulating LiF layer when the thickness of LiF layer is over 0.5nm.

This dissertation has focused on the study of the ITO/organic heterojunction and the chemistries therein, it proposes appropriate strategies that enhance the interfacial physical and electronic properties for charge injection with application to organic thin-layer devices. We focused on four major aspects of this work: i) To characterize the ITO surface and chemistries that may be pertinent to interaction with adjacent organic layers in a device configuration. This developed a working model of surface and provided a foundation for modification strategies. Characterization of the electronic properties of the surface indicate less than 5% of the geometrical surface is responsible for the bulk of current flow while the rest is electrically inactive. ii) To determine the extent to which these chemistries are variable and propose circumstances where compositional changes can occur. It is shown that the surface chemistry of ITO is heterogeneous and possible very dynamic with respect to the surrounding environment. iii) To propose a strategy for modification of the interface. Modification of ITO surfaces by small molecules containing carboxylic acid functionalities is investigated. Enhancements in the electron transfer rate coefficient were realized after modification of the ITO electrode. The enhancements are found to stem from a light etching mechanism. Additionally, an elecro-catalytic effect was observed with some of the modifiers. iv) Apply these modifications to organic light emitting diodes (OLEDs) and organic photovoltaic devices (OPVs). Enhancements seen in solution electrochemical experiments are indicative of the enhancements seen for solid state devices. Modifications resulted in substantially lower leakage currents (3 orders of magnitude in some cases) as well as nearly doubling the efficiency.An additional chapter describes the creation and characterization of electrochemically grown polymer nano-structures based on blazed angle diffraction gratings. The discussion details the micro-contact printing process and the electro-catalytic growth of the conductive polymers PANI and PEDOT to form diffraction grating structures in their own right. The resulting diffraction efficiency of these structures is shown to be sensitive to environmental conditions outlining possible uses as chemical sensors. This is demonstrated by utilizing these structures as working pH and potentiometric sensors based on the changing diffraction efficiency.

This work focusses on the high brightness performance of phosphorescent organic light-emitting diodes (OLEDs). The use of phosphorescent emitter molecules in OLEDs is essential to realize internal electron-photon conversion efficiencies of 100 %. However, due to their molecular nature, the excited triplet states have orders of magnitude longer time constants compared to their fluorescent counterparts which, in turn, strongly increases the probability of bimolecular annihilation. As a consequence, the efficiencies of phosphorescent OLEDs decline at high brightness – an effect known as efficiency roll-off, for which it has been shown to be dominated by triplet-triplet annihilation (TTA). In this work, TTA of the archetype phosphorescent emitter Ir(ppy)3 is investi- gated in time-resolved photoluminescence experiments. For the widely used mixed system CBP:Ir(ppy)3, host-guest TTA – an additional unwanted TTA channel – is experimentally observed at high excitation levels. By using matrix materials with higher triplet energies, this effect is efficiently suppressed, however further studies show that the efficiency roll-off of Ir(ppy)3 is much more pronounced than predicted by a model based on Förster-type energy transfer, which marks the intrinsic limit for TTA. These results suggest that the emitter molecules show a strong tendency to form aggregates in the mixed film as the origin for enhanced TTA. Transmission electron microscopy images of Ir(ppy)3 doped mixed films give direct proof of emitter aggregates. Based on these results, two concepts are developed that improve the high brightness performance of OLEDs. In a first approach, thin intrinsic matrix interlayers are incorporated in the emission layer leading to a one-dimensional exciton confinement that suppresses exciton migration and, consequently, TTA. The second concept reduces the efficiency roll-off by using an emitter molecule with slightly differ- ent chemical structure, i.e. Ir(ppy)2(acac). Compared to Ir(ppy)3, this emitter has a much smaller ground state dipole moment, suggesting that the improved performance is a result of weaker aggregation in the mixed film. The knowledge gained in the investigation of triplet-triplet annihilation is further used to develop a novel emission layer design for white organic LEDs. It comprises three phosphorescent emitters for blue, green, and red emission embedded in a multilayer architecture. The key feature of this concept is the matrix material used for the blue emitter FIrpic: Its triplet energy is in resonance with the FIrpic excited state energy which enables low operating voltages and high power efficiencies by reducing thermal relaxation. In order to further increase the device efficiency, the OLED architecture is optically optimized using high refractive index substrates and thick electron transport layers. These devices reach efficiencies which are on par with fluorescent tubes – the current efficiency benchmark for light sources. / Diese Arbeit richtet ihren Fokus auf die Untersuchung der Leistungsfähigkeit von phosphoreszenten, Licht-emittierenden organischen Dioden (OLEDs) im Bereich hoher Betriebshelligkeiten. Phosphoreszente Emittermoleku ̈le werden in OLEDs eingesetzt, um interne Elektron-Photon Konversionseffizienzen von 100% zu erreichen. Begründet in ihrer chemischen Struktur, weisen die angeregten Triplett-Zustände dieser Emitter um Größenordnungen längere Zeitkonstanten als die Emission fluo- reszenter Materialien auf, sodass die Wahrscheinlichkeit bimolekularer Auslöschung stark ansteigt. Dies resultiert in einem deutlichen Effizienzrückgang phosphoreszenter OLEDs bei großen Leuchtdichten. Dieser als Roll-off bekannter Effekt wird bei hohen Anregungsdichten hauptsächlich durch Triplett-Triplett Annihilation (TTA) bestimmt. In der Arbeit wird TTA an einem Modellmolekül, dem phosphoreszenten Emit- ter Ir(ppy)3, in zeitaufgelösten Photolumineszenz Experimenten untersucht. Für das bekannte Emittersystem CBP:Ir(ppy)3 wird bei hohen Anregungsdichten Host-Guest TTA beobachtet, was einen zusätzlichen, ungewünschten TTA Kanal darstellt. Dieser Effekt wird durch das Verwenden von Matrix Materialien mit höherer Triplett Energie vermieden, jedoch zeigt sich in weiteren Untersuchungen, dass der Roll-off deutlich stärker ist als von einem auf Förster Energieübertrag basierendem Modell vorhergesagt, welches selbst ein intrinsisches Limit für TTA in phosphoreszenten Systemen beschreibt. Die Diskrepanz zwischen experimenteller Beobachtung und Modellvorhersage wird durch eine starke Tendenz des Emitters, Aggregate zu bilden, erklärt, was TTA deutlich verstärkt. Diese Aggregate werden mit Hilfe von Transmissionselektronenmikroskopie an Ir(ppy)3-dotierten Mischsystemen direkt nachgewiesen. Basierend auf diesen Resultaten werden zwei Konzepte entwickelt, um die Effizienz phosphoreszenter Systeme bei hohen Helligkeiten zu verbessern. Im ersten Ansatz werden dünne intrinsische Schichten des Matrixmaterials in die Emissionsschicht eingebaut, was die Exzitonenbewegung in einer Raumrichtung und damit auch TTA stark unterdrückt. Das zweite Konzept reduziert den Effizienz Roll-off durch die Verwendung eines phosphoreszenten Emitters Ir(ppy)2(acac) mit einer leicht abgeänderten Molekularstruktur. Im Vergleich mit Ir(ppy)3 weist dieser ein deutlich kleineres Dipolmoment im molekularen Grundzustand auf, wodurch die Aggregation vermindert wird. Aufbauend auf den Ergebnissen der TTA wird ein neuartiges Emissionsschicht-Design für weißes Licht entwickelt. In diesem Konzept werden drei phosphoreszente Materialien für blaue, grüne und rote Farbe in eine Vielschicht-Architektur eingebracht. Das Hauptmerkmal der Emissionsschicht ist die Wahl des Matrix-Materials für dem blauen Emitter FIrpic: Seine Triplett Energie liegt resonant zu dem FIrpic Triplett Zustand, wodurch niedrige Betriebsspannungen und hohe Leistungseffizienzen ermöglicht werden, da die thermische Relaxierung reduziert wird. Um die Ef- fizienz dieser weißen OLEDs weiter zu erhöhen, wird die entwickelte OLED Architektur zusätzlich durch die Verwendung von hochbrechenden Substraten und dicken Elektronen-Transportschichten optisch optimiert. Bei beleuchtungsrelevanten Helligkeiten erreichen diese OLEDs das Effizienzniveau von Leuchtstoffröhren – letztere stellen heute den Effizienz-Maßstab dar.

Zugl.: Stuttgart, Univ., Diss., 2009

Zugl.: Stuttgart, Univ., Diss., 2009

University, Diss., 2003--Köln.

Copper(I) complexes have been studied through both experimental and computational means in the presented work. Overall, the work focuses on photophysical and photochemical properties of copper(I) complexes. Photophysical and photochemical properties are found to be dependent on the geometries of the copper(I) complexes. One of the geometric properties that are important for both photochemical and photophysical properties is coordination number. Coordination numbers have been observed to be dependent on both ligand size and recrystallization conditions. The complexes geometric structure, as well as the electronic effects of the coordination ligands, is shown both computationally as well as experimentally to affect the emission energies. Two-coordinate complexes are seen to have only weak emission at liquid nitrogen temperature (77 K), while at room temperature (298 K) the two-coordinate complexes are not observed to be luminescent. Three-coordinate complexes are observed to be luminescent at liquid nitrogen temperature as well as at room temperature. The three-coordinate complexes have a Y-shaped ground (S0) state that distorts towards a T-shape upon photoexcitation to the lowest lying phosphorescent state (T1). The geometric distortion is tunable by size of the coordinating ligand. Luminescence is controllable by limiting the amount of non-radiative emission. One manner by which non-radiative emission is controlled is the amount of geometric distortion that occurs as the complex undergoes photoexcitation. Bulky ligands allow for less distortion than smaller ligands, leading to higher emission energies (blue shifted energies) with higher quantum efficiency. Tuning emission and increasing quantum efficiencies can be used to create highly efficient, white emitting materials for use in white OLEDS.

This thesis deal with the audio preamplifier with input selector. It describes all designed parts of this device. It selects and describes all suitable components. Describes the whole process of electronics design in this device. Then describes the design, manufacture, assembling and testing of the PCB. In conclusion it shows the achieved results and electrical parameters of the device.

This work focusses on the high brightness performance of phosphorescent organic light-emitting diodes (OLEDs). The use of phosphorescent emitter molecules in OLEDs is essential to realize internal electron-photon conversion efficiencies of 100 %. However, due to their molecular nature, the excited triplet states have orders of magnitude longer time constants compared to their fluorescent counterparts which, in turn, strongly increases the probability of bimolecular annihilation. As a consequence, the efficiencies of phosphorescent OLEDs decline at high brightness – an effect known as efficiency roll-off, for which it has been shown to be dominated by triplet-triplet annihilation (TTA). In this work, TTA of the archetype phosphorescent emitter Ir(ppy)3 is investi- gated in time-resolved photoluminescence experiments. For the widely used mixed system CBP:Ir(ppy)3, host-guest TTA – an additional unwanted TTA channel – is experimentally observed at high excitation levels. By using matrix materials with higher triplet energies, this effect is efficiently suppressed, however further studies show that the efficiency roll-off of Ir(ppy)3 is much more pronounced than predicted by a model based on Förster-type energy transfer, which marks the intrinsic limit for TTA. These results suggest that the emitter molecules show a strong tendency to form aggregates in the mixed film as the origin for enhanced TTA. Transmission electron microscopy images of Ir(ppy)3 doped mixed films give direct proof of emitter aggregates. Based on these results, two concepts are developed that improve the high brightness performance of OLEDs. In a first approach, thin intrinsic matrix interlayers are incorporated in the emission layer leading to a one-dimensional exciton confinement that suppresses exciton migration and, consequently, TTA. The second concept reduces the efficiency roll-off by using an emitter molecule with slightly differ- ent chemical structure, i.e. Ir(ppy)2(acac). Compared to Ir(ppy)3, this emitter has a much smaller ground state dipole moment, suggesting that the improved performance is a result of weaker aggregation in the mixed film. The knowledge gained in the investigation of triplet-triplet annihilation is further used to develop a novel emission layer design for white organic LEDs. It comprises three phosphorescent emitters for blue, green, and red emission embedded in a multilayer architecture. The key feature of this concept is the matrix material used for the blue emitter FIrpic: Its triplet energy is in resonance with the FIrpic excited state energy which enables low operating voltages and high power efficiencies by reducing thermal relaxation. In order to further increase the device efficiency, the OLED architecture is optically optimized using high refractive index substrates and thick electron transport layers. These devices reach efficiencies which are on par with fluorescent tubes – the current efficiency benchmark for light sources. / Diese Arbeit richtet ihren Fokus auf die Untersuchung der Leistungsfähigkeit von phosphoreszenten, Licht-emittierenden organischen Dioden (OLEDs) im Bereich hoher Betriebshelligkeiten. Phosphoreszente Emittermoleku ̈le werden in OLEDs eingesetzt, um interne Elektron-Photon Konversionseffizienzen von 100% zu erreichen. Begründet in ihrer chemischen Struktur, weisen die angeregten Triplett-Zustände dieser Emitter um Größenordnungen längere Zeitkonstanten als die Emission fluo- reszenter Materialien auf, sodass die Wahrscheinlichkeit bimolekularer Auslöschung stark ansteigt. Dies resultiert in einem deutlichen Effizienzrückgang phosphoreszenter OLEDs bei großen Leuchtdichten. Dieser als Roll-off bekannter Effekt wird bei hohen Anregungsdichten hauptsächlich durch Triplett-Triplett Annihilation (TTA) bestimmt. In der Arbeit wird TTA an einem Modellmolekül, dem phosphoreszenten Emit- ter Ir(ppy)3, in zeitaufgelösten Photolumineszenz Experimenten untersucht. Für das bekannte Emittersystem CBP:Ir(ppy)3 wird bei hohen Anregungsdichten Host-Guest TTA beobachtet, was einen zusätzlichen, ungewünschten TTA Kanal darstellt. Dieser Effekt wird durch das Verwenden von Matrix Materialien mit höherer Triplett Energie vermieden, jedoch zeigt sich in weiteren Untersuchungen, dass der Roll-off deutlich stärker ist als von einem auf Förster Energieübertrag basierendem Modell vorhergesagt, welches selbst ein intrinsisches Limit für TTA in phosphoreszenten Systemen beschreibt. Die Diskrepanz zwischen experimenteller Beobachtung und Modellvorhersage wird durch eine starke Tendenz des Emitters, Aggregate zu bilden, erklärt, was TTA deutlich verstärkt. Diese Aggregate werden mit Hilfe von Transmissionselektronenmikroskopie an Ir(ppy)3-dotierten Mischsystemen direkt nachgewiesen. Basierend auf diesen Resultaten werden zwei Konzepte entwickelt, um die Effizienz phosphoreszenter Systeme bei hohen Helligkeiten zu verbessern. Im ersten Ansatz werden dünne intrinsische Schichten des Matrixmaterials in die Emissionsschicht eingebaut, was die Exzitonenbewegung in einer Raumrichtung und damit auch TTA stark unterdrückt. Das zweite Konzept reduziert den Effizienz Roll-off durch die Verwendung eines phosphoreszenten Emitters Ir(ppy)2(acac) mit einer leicht abgeänderten Molekularstruktur. Im Vergleich mit Ir(ppy)3 weist dieser ein deutlich kleineres Dipolmoment im molekularen Grundzustand auf, wodurch die Aggregation vermindert wird. Aufbauend auf den Ergebnissen der TTA wird ein neuartiges Emissionsschicht-Design für weißes Licht entwickelt. In diesem Konzept werden drei phosphoreszente Materialien für blaue, grüne und rote Farbe in eine Vielschicht-Architektur eingebracht. Das Hauptmerkmal der Emissionsschicht ist die Wahl des Matrix-Materials für dem blauen Emitter FIrpic: Seine Triplett Energie liegt resonant zu dem FIrpic Triplett Zustand, wodurch niedrige Betriebsspannungen und hohe Leistungseffizienzen ermöglicht werden, da die thermische Relaxierung reduziert wird. Um die Ef- fizienz dieser weißen OLEDs weiter zu erhöhen, wird die entwickelte OLED Architektur zusätzlich durch die Verwendung von hochbrechenden Substraten und dicken Elektronen-Transportschichten optisch optimiert. Bei beleuchtungsrelevanten Helligkeiten erreichen diese OLEDs das Effizienzniveau von Leuchtstoffröhren – letztere stellen heute den Effizienz-Maßstab dar.