This master´s thesis proposal addresses the heating from the perspective of primary energy in the object. The building is located in Brno and is used as a villa with a pool hall. The object of this work is the selection of appropriate variants of three heat sources (gas boiler, pellet and electric) in terms of primary energy. The project is design of the heating system chosen mode of heat, which is a pellet boiler. The theoretical part is focused on the pellets and their history, classification, properties, production, storage and transport.

This master´s thesis focuses on a design of a heating system in the functionalist villa Stiassni. The building is located in Brno and was used as a government villa. The objec-tive of this work is to select the appropriate type of heating system out of three differ-ent heat sources – an automatic pellet boiler, a gas boiler and an oil boiler. The theo-retical part is focused on the history of the villa Stiassnia, functionalism itself and other functionalist monuments. In the project part, the design of a heating system using the chosen type of heat source, which is a pellet boiler, is described.

MENVSC / Department of Ecology and Resource Management / See the attached abstract below

<p>  </p> <p>Direct reduction ironmaking has gained popularity as a low carbon alternative to the typical blast furnace ironmaking route. A popular method of producing direct reduced iron is through the reduction of iron ore pellets in a reduction shaft furnace. Critical to this process is the use of a reliable continuous pellet feed system to provide a steady flow of pellets to the furnace. Therefore, any disruption in pellet flow can have a significant negative impact on the production rate of iron. </p> <p><br></p> <p>An iron ore pellet feed system for a direct reduction ironmaking furnace is jamming during winter operation. The pellets are jamming in a hopper at the top of the feed system above the furnace, and a hot gas, that seals off the furnace flue gas, flows counter to the pellets. A computational model of the feed system is built utilizing the discrete element method and computational fluid dynamics, using Siemen’s commercial multiphysics software Star-CCM+, to study the conditions that cause the jam to occur. The study is divided into six parts: pellet bulk flow calibration, computational cost reduction, modeling of the baseline operation, modeling the effect of moisture, development of a thermal model, and investigation of the minimal amount of icy and wet material to jam the system. The findings show that the location of jamming during operation matches the area in the simulation where it is most likely to occur, and that moisture alone is unlikely to result in jamming. Results indicate that the system will jam when charged with a minimum of 15% icy pellets, and when charged with 10% icy together with 5% wet pellets. Experimental work is recommended to validate the findings and to calibrate the simulations accordingly.</p>

The number of biogas plants in Germany is increasing from 3,711 in 2007 to 8,075 in 2016. In these biogas plants, it occurred more than 50 Mt digestate. Therefore, several investigations are started to use digestate as organic fertiliser mostly for field crop cultivation. Experiment with tomatoes was carried out were digestate was used as a supplement to the growing media in an amount of 5%, 15%, and 25%, compared with a treatment of mineral fertiliser and lupine wholemeal. The tomato yield was highest in the treatment with mineral fertilisation, the yield with 25% digestate was only a little lower. More experiments are necessary for particular regarding the amount and frequency of fertilization with digestate from biogas plants. In Germany and in Vietnam the number of sheep flocks is increasing, high amounts of uncleaned sheep wool are available. Because of the high amount of nutrients - especially nitrogen -, sheep wool pellets could be used as multi-functional fertiliser in vegetable cultivations. Four types of sheep wool pellets have been tested in protected cultivation. Tomatoes were cultivated in a greenhouse using substrate culture with perlite, bark compost, sheep wool slabs, respectively, and sheep wool pellets as fertiliser. Best growth and highest yield for tomatoes were obtained using pine bark and perlite as a substrate, both fertilised with sheep wool pellets. Based on the results of the yield and the analyses of the nutrient content in plants it seems that sheep wool pellets can be used, for the cultivation of vegetables in greenhouses. / Số lượng các nhà máy biogas tại CHLB Đức tăng từ 3.711 năm 2017 lên 8.075 năm 2016. Các nhà máy biogas sản sinh ra hơn 50 triệu tấn chất thải. Vì vậy đã có nhiều nghiên cứu liên quan đến sử dụng nguồn chất thải này làm phân bón hữu cơ cho canh tác nông nghiệp. Thí nghiệm với cà chua sử dụng chất thải biogas làm chất bổ sung dinh dưỡng cho giá thể trồng cây theo các tỷ lệ 5%, 15% và 25% đối chứng với công thức sử dụng phân hóa học và bột nguyên vỏ họ đậu. Năng suất cà chua thu được từ các công thức bổ sung chất thải biogas đều cao hơn đối chứng, chỉ có công thức bổ sung 25% có năng suất thấp hơn. Tuy nhiên vẫn cần có những nghiên cứu tiêp theo về lượng và tần xuất sử dụng bón phân với chất thải từ nhà máy biogas. Ở Đức và ở Việt Nam số lượng đàn cừu đang tăng lên, một lượng lớn lông cừu phế phẩm phát sinh. Với hàm lượng dinh dưỡng cao, đặc biệt là nitơ, viên nén từ lông cừu phế phẩm có thể sử dụng làm phân bón đa chức năng cho trồng trọt. Nghiên cứu đã sử dụng 4 loại viên nén lông cừu làm phân bón trong điều kiện trồng có kiểm soát. Cà chua được trồng trong nhà kính với 3 loại giá thể là perlite, vỏ cây thông đã ủ hoai, thảm lông cừu với phân bón là viên nén từ lông cừu phế phẩm. Năng suất cao nhất và đem lại sinh trưởng tốt nhất cho cây cà chua là công thức sử dụng vỏ cây thông và perlite. Dựa trên kết quả về năng suất và phân tích dinh dưỡng trong cây và sản phẩm, nghiên cứu cho thấy sự phù hợp của viên nén từ lông cừu phế phẩm làm phân bón cho canh tác rau trong nhà kính.

[pt] O processo de formação de pelotas de minério de ferro consiste na preparação das matérias-primas, formação da pelota crua e endurecimento por meio da queima. O produto final deve ser um material poroso que permita a difusão de gases no forno de redução e que, simultaneamente, resista a compressão, característica relevante durante o transporte e no carregamento do forno. No entanto, durante o tratamento térmico e o transporte podem surgir trincas que comprometem a integridade das pelotas. A discriminação de poros e trincas é, portanto, um importante fator para a análise microestrutural e controle de qualidade do material. A microtomografia de raios-x é uma técnica não destrutiva que gera imagens tridimensionais, o que permite uma visualização completa da pelota. No entanto, a metodologia usual de processamento digital de imagens, baseada em extração de atributos de tamanho e forma, apresenta limitações para discriminar poros de trincas. Redes Neurais Deep Learning são uma alternativa poderosa para classificar tipos de objetos em imagens, utilizando como entrada as intensidades dos pixels e atributos automaticamente determinados pela rede. Após treinar um modelo com os padrões correspondente a cada classe, é possível atribuir cada pixel da imagem a uma das classes presentes, permitindo uma segmentação semântica. Nesta dissertação, otimizou-se uma rede Deep Learning com arquitetura U-Net, usando como conjunto de treinamento poucas camadas 2D da imagem 3D original. Aplicando o modelo à pelota utilizada no treinamento foi possível discriminar poros de trincas de forma adequada. A aplicação do modelo a outras pelotas exigiu a incorporação de camadas destas pelotas ao treinamento e otimização de parâmetros do modelo. Os resultados apresentaram classificação adequada, apesar de apresentar dificuldades de criar um modelo geral para discriminação entre poros e trincas em pelotas de minério de ferro. / [en] The iron ore pellet forming process consists of preparing the raw materials, forming the raw pellet and hardening by firing. The end product must be a porous material which allows gas to diffuse in the blast furnace and at the same time resists compression, which is a relevant feature during transport and loading of the furnace. However, during heat treatment and transport cracks may appear that compromise the integrity of the pellets. The discrimination of pores and cracks is therefore an important factor for microstructural analysis and material quality control. X-ray microtomography is a non-destructive technique that generates three-dimensional images, allowing a full view of the pellet. However, the usual methodology of digital image processing, based on extraction of size and shape attributes, has limitations to discriminate crack from pores. Deep Learning Neural Networks are a powerful alternative to classifying object types in images, using as input the pixel intensities and attributes automatically determined by the network. After training a model with the patterns corresponding to each class, it is possible to assign each pixel of the image to one of the classes present, allowing a semantic segmentation. In this dissertation, a Deep Learning network with U-Net architecture was optimized, using as a training set a few 2D layers of the original 3D image. Applying the model to the pellet used in training it was possible to discriminate cracks pores properly. Application of the model to other pellets required the incorporation of layers of these pellets into the training and optimization of model parameters. The results were adequately classified, despite the difficulty of creating a general model for discrimination between pores and cracks in iron ore pellets.

This thesis aims to find out the effective diffusivity (Deff) of a porous material – γ-alumina, using an unsteady state method with two inert gases at ambient condition with no reactions. For porous materials, Deff is important because it determines the amount of reactants that transfers to the surface of pores. When Deff is known, the apparent tortuosity factor of γ-alumina is calculated using the parallel pore model. The apparent tortuosity factor is important because: (a) it can be used to back-calculate Deff at reacting conditions; (b) once Deff with reactions is known, the Thiele modulus can be calculated and hence the global reaction rate can be found; (c) apparent tortuosity factor is also important for modelling purposes (e.g. modelling a packed-bed column or a catalytic combustion reactor packed with porous γ-alumina in various shapes and monoliths). Experimental measurements were performed to determine the effective diffusivity of a binary pair of non-reacting gases (He in N2, and N2 in He) in spherical γ-alumina pellets (1 mm diameter), and in γ-alumina washcoated monoliths (washcoat thickness 20 to 60 µm, on 400 cpsi (cells per square inch) cordierite support). The method used is based on the chromatographic technique, where a gas flows through a tube, which is packed with the sample to be tested. A pulse of tracer gas is injected (e.g. using sample loops: 0.1, 0.2, 0.5 ml) and by using an on-line mass spectrometer the response in the outlet of the packed bed is monitored over time. For the spherical pellets, the tube i.d. = 13.8 mm and the packed bed depths were 200 and 400 mm. For monoliths the tube i.d. = 7 mm and the packed lengths were 500 and 1000 mm. When the chromatographic technique was applied to the monoliths, it was observed that experimental errors can be significant, and it is very difficult to interpret the data. However, the technique worked well with the spherical pellets, and the effective diffusivity of He in N2 was 0.75 – 1.38 × 10-7 m2 s-1, and for N2 in He was 1.81 – 3.10 × 10-7 m2 s-1. Using the parallel pore model to back-calculate the apparent tortuosity factor, then a value between 5 to 9.5 was found for the pellets.

Today a lot of attention is focused on compounds called endocrine disrupters (EDs) among substances released to environment by humans. They are a group of substances which can disturb function of hormonal system of organisms including humans. Their poor removal at wastewater treatment plants (WwTP) were shown at various studies, thus they can reach the environment in water. A prospective way for the degradation of EDs at WwTP can be their removal by ligninolytic fungi. They are able to degrade lots of lignin-like aromatic substances because of their highly nonspecific enzymes. In this work growth and enzyme production capability of four ligninolytic fungal strains were monitored on three solid substrates (straw pellets, poplar sawdust mixed with straw pellets, oak sawdust with straw pellets), which may be suitable substrates for fungal growth in bioreactors for wastewater treatment. Ability of these enzymes to degrade EDs were tested in in-vitro degradation experiment. Trametes versicolor was found as best degrading strain with 20 μg/ml of bisphenol A, 17 α- ethynylestradiol and nonylphenol degraded below a quantification limit within 24 hours. Fungal strains degraded EDs well on all of the three substrates but wood sawdust seemed to be a better substrate for fungal growth because straw pellets...

Ce travail porte sur la synthèse, la mise en forme et la caractérisation desolutions solides de type tysonite RE1-xMxF3-x (RE = La, Sm, Ce et M = Ba, Ca, Sr). Dans unpremier temps, une démarche d’étude rigoureuse est mise en place pour la solution solide ditede référence, La1-xBaxF3-x. Les synthèses menées à l’état solide aboutissent à une maîtrise dela composition chimique et à l'établissement de lois de variations des paramètres structuraux.Une meilleure compréhension de l’influence de la structure sur la mobilité des ions F- estégalement acquise. L’influence du frittage dans l’obtention de bonnes valeurs de conductivitéionique est également à souligner. Dans un second temps, les effets de la nanostructurationpar mécanobroyage sur les propriétés de conductivité sont évalués. L’utilisation de laméthodologie des plans d’expériences mène à la mise au point des réglages optimums debroyage. Il apparaît alors que la synthèse des électrolytes peut être accélérée et mise àl’échelle tout en gardant des valeurs optimales de conductivité. Enfin, la démarche déterminéeest appliquée à d'autres solutions solides de type tysonite et à la recherche du conducteurionique le plus performant. Si les composés issus de la substitution Ce/Sr ou encore Sm/Casemblent les plus prometteurs, la plus grande stabilité chimique de la solution solide La1-xSrxF3-x est le compromis idéal pour l'utiliser comme électrolyte solide lors des mesuresélectrochimiques des batteries. / This work deals with the synthesis, shaping and characterization of RE1-xMxF3-x (RE = La, Sm, Ce et M = Ba, Ca, Sr) tysonite-type solid solutions. In a first part, onemeticulous approach has been set up for La1-xBaxF3-x solid solution, chosen as a reference.The solid-state synthesis of these materials led to a better knowledge of their chemicalcomposition (Vegard’s laws) and of the structure-ionic mobility correlations. The impact ofthe sintering process on the ionic conductivity is also highlighted. In a second part, the effectsof the nanostructuration conducted by ball-milling of the microcrystalline samples areevaluated. The use of the Design of Experiments methodology led to identify the optimummilling conditions. It appears that the synthesis of electrolytes can be sped- and scaled-up,while keeping high ionic conductivity properties. At last, this approach is applied on othertysonite-type solid solutions, to look for the best electrolyte. The Ce/Sr and Sm/Casubstitutions generate very promising ionic conductors but not really (electro)chemicallystable compounds. A compromise has been found with the choice of the La1-xSrxF3-x solidsolution as the FIB electrolyte for the electrochemical performances tests, regarding its higherchemical stability.

Solution combustion synthesis (SCS) with its origin at IPC department of IISc has been widely practiced for synthesis of oxide materials. It is simple and low cost process, with energy and time savings that can be used to produce homogeneous, high purity, uniformly doped, nano crystalline ceramic powders. The powders characteristics such as crystallite size and surface area are primarily governed by enthalpy, flame temperature of combustion, fuel and fuel to oxidizer ratio ( F/O). In the present work an attempt has been made to investigate the process in order to exercise a control over the phase formation and nature of the product. Initial part of the work deals with the effect of fuel to oxidizer ratio on the powder properties of binary oxides with urea as fuel. The variation of adiabatic flame temperatures are calculated theoretically for different F/O ratios according to thermodynamic concept and correlated with the observed flame temperatures. Difference in the measured flame temperature and theoretical flame temperature in the fuel rich region is explained on the basis of incomplete combustion model. The effect of decomposition temperature difference of fuel and oxidizer, solubility of reactants on exothermicity of combustion reaction taking aluminiumnitrate system for various fuels is investigated. The effect of mixed fuel approach is studied by using the urea-glycine mixed fuel system using aluminium nitrate as oxidizer and employed for successful synthesis of the gamma alumina. Further Compaction behavior of SCS nano ceramic powders is studied by using Universal testing machine and the effect of F/O ratio, on agglomeration strength, aggregation strength of powder is investigated. Very few reports can be found on usage of SCS ceramic powder for biomaterial applications. By using these investigations a pyroxene series Diopside (CaMgSi2O6) silicate material is synthesized by SCS. Effect of different fuels on Diopside (DP) phase formation is investigated. Finally the DP and DP-ZnO composites, made by using Uniaxial hot pressing are investigated for their antibacterial, cytocompatibility properties. Antibacterial activity of E.Coli bacterium of Diopside powders was dose dependent type. Results of the bioactivity investigations shown flattened MC3T3 mouse osteoblast cells and MC C2C12 Myoblast cells and linkage bridges formed between them on Diopside and DP-ZnO surfaces show cyto compatibility and MTT results showed that percentage of ZnO needs to be tailored between 0-10 in order to achieve maximum cytocompatibility coupled with antibacterial property.