Functionalized membranes provide an elegant platform for selective separations and sorptions. In this dissertation, application of functionalized membranes for surfactant and metal sorption studies are discussed. Sorption behavior of surfactants is also studied using quartz crystal microbalance (QCM) and other techniques. Adsorption of the ethoxylated surfactants on polymeric materials (cotton and polyester) and model gold surface was quantified from a non-aqueous siloxane based solvent (D5) and water. The role of ethylene oxide group and the effect of nature of polymeric materials on adsorption behavior was quantified and established. In the case of gold-water interface, the adsorption data was fitted to calculate adsorption/desorption rate constants. The study is important towards applications involving use of the surfactants in cleaning operations. PAA functionalized membranes were prepared and used for separation of the surfactants from the siloxane solvent. Finally the pH sensitivity of the PAA-surfactant complex was verified by successful regeneration of the membrane on permeation of slightly alkaline water. The preparation and application of thiol and sulfonic acid functionalized silica mixed matrix membranes for aqueous phase metal ion sorption is also studied. The functionalized particles were used as the dispersed phase in the polysulfone or cellulose acetate polymer matrix. The effects of the silica properties such as particle size, specific surface area, and porous/nonporous morphology on the metal ion sorption capacity were studied. Silver and ferrous ions were studied for metal sorption capacities. The ferrous ions were further reduced to prepare membrane immobilized iron nanoparticles which are attractive for catalytic applications. One dimensional unsteady state model with overall volumetric mass transfer coefficient was developed to model the metal ion sorption using mixed matrix membrane. The study demonstrates successful application of the functionalized mixed matrix membranes for aqueous phase metal capture with high capacity at low transmembrane pressures. The technique can be easily extended to other applications by altering the functionalized groups on the silica particles. The study is important towards water treatment applications and preparation of membrane immobilized metal nanoparticles for catalytic applications.

Thesis (MScMedSc)--Stellenbosch University, 2012. / Bibliography / ENGLISH ABSTRACT: South Africa is ranked amongst the top tuberculosis (TB) burden countries in the world and the Western Cape has a particularly high incidence of the disease. Previous studies have showed that several genes may play crucial roles in susceptibility to TB. In this study, we investigated the role of three genes previously associated with susceptibility to TB and progression to disease. These genes were Surfactant protein D (SFTPD), Macrophage receptor with collagenous structure (MARCO) and CD14. The proteins from these genes bind M. tuberculosis and are involved in the uptake of the bacteria into macrophages. The study investigated the role of ten polymorphisms from SFTPD and MARCO within a South African Coloured (SAC) population, where tuberculosis is highly prevalent. A casecontrol study design was used and polymorphisms were genotyped with Taqman® genotyping assays and amplification refractory mutation system polymerase chain reaction (ARMS-PCR). The results were analysed for association with disease, linkage disequilibrium, haplotypes and gene-gene interactions. Allele and genotype frequencies were also determined which allowed for comparisons to other populations. Five SNPs were associated with TB: two in SFTPD (rs1923537; rs2255326) and three in MARCO (rs1318645; rs3943679; rs2119112). The associated SNPs were located in regions other than exons and the effects of polymorphisms in these regions are not well understood but studies in other genes have shown them to play a functional role. Gene-gene interaction analysis showed that polymorphisms interacted with each other within and between genes, illustrating the importance of epistasis and the complexity of the genetic influences on TB. In addition to the case-control association studies, the role of the rs2569190 promoter SNP in CD14 was assessed. Gene-expression analysis was conducted with qPCR and a reporter gene assay and results from both of these approaches showed that individuals with the TT genotype had a twofold greater expression level than individuals with the CC genotype. Previously, the TT genotype has been associated with stronger promoter activity and expression of soluble CD14 in serum. Since the TT genotype was present at a higher frequency in the control group, we speculate that greater expression of CD14 may contribute to a more TB resistant phenotype. The work presented in this study illustrates the importance of the host genetic component of TB. Genetic studies will eventually revolutionize the current treatment regime as the identification of vulnerable individuals and populations will aid in the development of personalised medicines. / AFRIKAANSE OPSOMMING: Suid-Afrika is een van die top tuberkulose (TB) lande in die wêreld en die Wes-Kaap het veral ‘n hoë insidensie van die siekte. Vorige studies het gewys dat verskeie gene bydra to die vatbaarheid vir tuberkulose. In hierdie studie het ons drie gene, wat voorheen vir vatbaarheid vir tuberkulose en progressie na die siekte ondersoek is, bestudeer. Hierdie gene is Surfactant protein D (SFTPD), Macrophage receptor with collagenous structure (MARCO) en CD14. Die proteïene van hierdie gene bind M. tuberculosis en is betrokke in die opname van die bakterieë in die makrofages. Hierdie studie het tien polimorfismes van SFTPD en MARCO in die Suid-Afrikaanse Kleurlingbevolking (SAK), wat ‘n hoë TB insidensie het, getoets. Pasiënt-kontrole assosiasie studies is gedoen en polimorfismes is gegenotipeer met Taqman® genotiperingsisteem en die amplifikasie refraktoriese mutasie sisteem polimerase ketting reaksie (ARMS-PCR). Die resultate is geanaliseer vir assosiasies met TB, koppelings disekwilibrium, haplotipes en geen-geen interaksies. Alleel en genotype frekwensies is ook bepaal en vergelyk met die van ander bevolkings. Vyf enkel nukleotied polimorfismes (ENPs) is met TB geassosieer: twee in SFTPD (rs1923537; rs2255326) en drie in MARCO (rs1318645; rs3943679; rs2119112). Die geassosieerde ENPs was nie in eksons nie. Die effek van polimorfismes in areas anders as eksons word nie goed verstaan nie, maar studies het bewys dat hulle wel ‘n funksionele rol kan hê. Geen-geen interaksie analise het gewys dat polimorfismes interaksies met mekaar binne sowel as tussen gene gehad het, wat die belangrikheid van epistase en die kompleksiteit van genetiese invloede op TB illustreer. Tesame met die pasiënt-kontrole assosiasie studies is die rol van die rs2569190 promoter ENP in CD14 ook ondersoek. Geenuitdrukkingsanalise is gedoen met qPKR en rapporteerder geen toetse. Die resultate van beide hierdie benaderings het gewys dat individue met die TT genotipe twee keer soveel uitdrukkingsvlakke gehad het as individue met die CC genotipe. Die TT genotipe is voorheen geassosieer met sterk promoter aktiwiteit en die uitdrukking van oplosbare CD14 in serum. Aangesien die TT genotipe meer in die kontrolegroep gevind is, spekuleer ons dat die hoër uitdrukking van CD14 kan bydra tot ‘n meer TB weerstandbiedende fenotipe. Hierdie werk illustreer die belangrikheid van die gasheer genetiese komponent in TB. Genetiese studies sal in die toekoms die huidige behandeling regime revolusioneer, aangesien die identifikasie van individue en bevolkings met ‘n hoë risiko om TB te ontwikkel sal bydra tot die ontwikkeling van persoonlike medisynes. / The National Research Foundation (NRF); the South African Medical Research Council (MRC); Stellenbosch University and the Harry Crossley Foundation.

Des matériaux hybrides organiques-inorganiques mésostructurés ont été élaborés par deux voies différentes: le procédé sol-gel et l'assemblage de « briques » hybrides moléculaires. Dans une première partie, nous nous sommes intéressés à la synthèse directe de mésoporeux cubiques monofonctionnalisés (SBA-16) par voie sol-gel. Différents groupements organiques ont été insérés dans les pores du matériau (SH, CN, Cl, PO(OEt)2 et acac). Leur accessibilité a été mise en évidence par la complexation d'un lanthanide (europium) grâce aux fonctions acac, mais aussi par la croissance de nanoparticules d'or régulièrement distribuées dans les pores grâce aux groupements SH. Grâce à leur petite taille (2nm) et leur accessibilité, ces nanoparticules ont pu être utilisées en catalyse. Notre étude a ensuite été étendue aux matériaux mésoporeux bifonctionnels. La fonctionnalisation des pores et de la charpente de silices hexagonales (SBA-15) a été réalisée en une seule étape. Plusieurs fonctionnalités chimiques ont été insérées avec succès et ont permis le confinement intime de deux types de nanoparticules pouvant interagir entre-elles. Le matériau est alors qualifié d' « interactif ». Dans une dernière partie, nous avons développé une nouvelle approche de la synthèse de matériaux 3D organisés par assemblage de « cages » moléculaires hybrides (octasilsesquioxanes fonctionnalisés). Nous avons choisi des fonctions Cl, facilement convertibles en acides ou en ions et capables de s'auto-assembler par liaisons faibles (liaisons H) ou par forces coulombiennes. Nous avons également envisagé d'utiliser des « connecteurs » organiques comme le cyclame, capables de lier les différentes cages par liaison covalente et de fixer des ions métalliques. / Mesostructured hybrid materials (organic-inorganic) were prepared according two different ways: the sol-gel process on the one hand, the assembly of molecular hybrid 'bricks' on the other. In the first part, we focused on the one-pot synthesis of monofunctionalised cubic silicas (SBA-16) through the sol-gel process. Different organic functions were successfully introduced within the pores of the material (SH, CN, Cl, PO(OEt)2 and acac). Their accessibility was brought to light by complexation of lanthanide salts (europium) by acac moieties, but also by growing of gold nanoparticles within the pores, regularly distributed thanks to the SH groups. Thanks to their small size (2 nm) and their high accessibility, these supported nanoparticles could be used as catalysts. Secondly, our study was extended to bifunctional materials. 2-D hexagonal silicas (SBA-15) were functionalised by one-step synthesis within both pores and walls. Several organic groups were covalently included within the structure, which then allowed us to confine very closely two kinds of nanoparticles, able to interact between themselves at nanometric scale. The bimetallic material is consequently qualified as 'interactive'. The last part was dedicated to a new approach for the synthesis of 3-D structured materials, consisting in the assembly of hybrid molecular 'cages' (functionalised octasilsesquioxanes). Chloro terminations were chosen because of their easy conversion into acid or ionic moieties, able to self-assemble, driven by weak interactions such as H-bonds or electrostatic forces. The use of organic “linkers” such as cyclam groups was also considered to connect cages and anchor metallic ions.

The administration of pharmaceutical aerosols to infants on mechanical ventilation needs to be improved by increasing the efficiency of delivery devices and creating better ways of evaluating potential therapies. Aerosolized medicines such as surfactants have been administered to ventilated infants with mixed results, but studies have shown improvement in respiratory function with a much lower dose than with liquid instillation through an endotracheal tube (ETT). An aerosolized medicine must be transported through the ventilation tubing and deposit in the lungs to have the desired therapeutic response. This work has taken a systematic approach to (i) develop new devices for the efficient production of small sized charged pharmaceutical aerosols, (ii) adapt a lead device to an infant ventilation system, (iii) develop a novel breathing infant lung (BIL) in vitro model capable of capturing lung delivery efficiency in an infant without the need for human subjects testing, and (iv) evaluate the hypothesis that small sized charged pharmaceutical aerosols can improve drug delivery efficiency to the lungs of a ventilated infant. Three new devices were developed and screened for the efficient generation of small sized charged pharmaceutical aerosols, which were: wick electrospray, condensational vapor, and a modified vibrating mesh nebulizer in a streamlined low flow induction charger (LF-IC). Of these devices, only the LF-IC produced a small [mean(SD) = 1.6(0.1) micrometers] and charged (1/100 Rayleigh limit) aerosol at a pharmaceutically relevant production rate [mean(SD) = 183(9) micrograms per minute]. The LF-IC was selected as a lead device and adapted for use in an infant ventilation system, which produced an increase in in vitro lung filter deposition efficiency from 1.3% with the commercial system to 34% under cyclic ventilation conditions. The BIL model was first shown to produce a realistic pressure-volume response curve when exposed to mechanical ventilation. The optimized LF-IC was then implemented in the BIL model to demonstrate superior reduction in inspiratory resistance when surfactant was delivered as an aerosol compared to liquid instillation. For the delivery of an aerosolized medication, the lung deposition efficiency increased from a mean(SD) 0.4(0.1)% when using the conventional delivery system to 21.3(2.4)% using the LF-IC in the BIL model, a 59-fold increase. The charged aerosol produced by the LF-IC was shown to have more depositional loss in the LF-IC than an uncharged aerosol, but the charge decreased the exhaled fraction of aerosol by 17%, which needs additional study to achieve statistical significance. Completion of this work has produced a device that can achieve lung delivery efficiency that is 59-fold greater than aerosols from conventional vibrating mesh nebulizers in invasively ventilated infants using a combination of small particle size, synchronization with inspiration and appropriate charge. The BIL model produced in this work can be used to test clinically relevant methods of administering medications to infants and can be used to provide more accurate delivery estimates for development of new nebulizers and inhalers. The LF-IC developed in this work could be used for controlled and efficient delivery of aerosolized antibiotics, steroids, non-steroidal anti-inflammatories, surfactants, and vasodilators.

Une série de précurseurs contenant des sous-structures organo-ioniques à base d'entités imidazolium, guanidinium, ammonium et zwitterionique ainsi que des précurseurs neutres contenant des sous-structures amido-thiol, amine-thiol et amine a été synthétisée. Ces précurseurs ont été utilisés pour la synthèse de matériaux silices hybrides nanostructurés par voie template. La formation de matériaux nanostructurés a été réalisée par des réactions d'hydrolyse-polycondensation par l'utilisation de différents agents de structuration. Ce travail avait pour but la détermination des principaux facteurs influençant la structuration des matériaux. Ainsi, nous avons préparé une série d'ionosilicates nanostructurés par une nouvelle méthode de structuration qui met en jeu des interactions spécifiques entre des paires d'ions ‘précurseur cationique - surfactant anionique' et ‘précurseur anionique - surfactant cationique'. Cette approche a permis d'accéder aux matériaux originaux de type PMO ionique. Finalement, nous avons utilisé pour la première fois des surfactants de guanidinium comme ‘template' dans la synthèse des silices ioniques nanostructurées de morphologie sphérique. Les matériaux nanostructurés contenant des sous-structures amine, amine-thiol, ammonium et zwitterionique développés au cours de ce travail présentent des surfaces spécifiques élevées et une bonne accessibilité des sites organiques. Ces propriétés font de ces matériaux des systèmes de choix pour des applications en catalyse ou en séparation. / A series of precursors containing organo-ionic substructures such as imidazolium, guanidinium, ammonium and zwitterionic entities and several neutral precursors containing thiol-amide, thiol-amine and amino groups were successfully synthesized. These precursors were used for the synthesis of nanostructured silica hybrid materials containing ionic substructures via soft templating approaches. The formation of structured materials was achieved using template directed hydrolysis polycondensation procedures in the presence of various structure directing agents. The goal of this study was the determination of the parameters influencing the structuring of the materials. Thus, we prepared a series of nanostructured ionosilicates using a new method of structuring that is based on specific interactions between ‘cationic precursor - anionic surfactant' and ‘anionic precursor - cationic surfactant' ion pairs. This new strategy allowed the synthesis of ionic 'periodic mesoporous organosilicas'. At the end of this thesis, we used a new ‘guanidinium' type template in the preparation of nanostructured i-silica hybrid materials with a spherical morphology. Nanostructured ionosilicates bearing amine, amino-thiol, ammonium and zwitterionic substructures prepared in this work present high specific surface areas and a high accessibility of the organic functional sites. Due to these features, these materials have large potential in the fields of catalysis and separation.

Les mousses liquides sont très utilisées dans l'industrie comme dans la vie quotidienne. Cependant, leur stabilité n'est ni complètement comprise ni complètement maîtrisée, la formulation étant essentiellement empirique. Il est donc difficile d'une part de prédire la capacité d'une solution de tensioactifs à générer des mousses et d'autre part de prédire et de contrôler leur déstabilisation. Ce travail de thèse propose des expériences conceptuellement simples qui s'appuient sur le caractère multi-échelle des mousses pour tenter d'établir des liens clairs entre physico-chimie et mécanismes de déstabilisation. Dans un premier temps, nous avons revisité une expérience d'entraînement de films liquides sur un cadre pour illustrer la stabilité des films lors de la génération des mousses ou pendant un réarrangement (processus T1). Nous avons mis en lumière l’existence de deux régimes. Un régime dit non confiné, pour lequel la stabilité des films et réduite et dépend de la physico-chimie. Un régime dit confiné pour lequel le rôle de la physico-chimie est limité et la stabilité est majoritairement contrôlée par l’hydrodynamique.Dans un second temps nous nous sommes intéressés à l'influence de la physico-chimie et de la fraction liquide sur la compétition entre coalescence et mûrissement grâce à l'étude d'une unique couche de bulles (mousse 2D). Nous proposons une méthode de mesure in situ de la perméabilité des films par l'étude simple et rapide du régime transitoire du mûrissement de mousses 2D. Nous avons observé une corrélation entre coefficient de diffusion du gaz contenu dans les bulles et perméabilité.Enfin nous décrivons les résultats d’une expérience spatiale sur le vieillissement à temps long des mousses humides (fraction liquide supérieure à 30% en volume), extrêmement difficile sur Terre à cause du drainage gravitaire, et à laquelle nous avons participé. / Liquid foams are widely used in industry and in everyday life. However, their stability is not fully understood or fully controlled, their formulation being essentially empirical. It is therefore difficult to predict the ability of a surfactant solution to generate foam and to control their destabilization. This thesis proposes simple experiments that rely on the multi-scale nature of foams in order to attempt to establish clear links between physical chemistry and stability.First of all, we revisited an experiment of liquid films entrainment to illustrate the stability of foam films during generation or rearrangement (T1 process). We have shown the existence of two regimes: (i) a unconfined regime, for which the stability of films is reduced and depends on physical chemistry and (ii) a confined regime for which the role of physical chemistry stability is limited and is mainly controlled by hydrodynamics.Secondly, we investigated the influence of physical chemical and liquid fraction on the competition between coalescence and coarsening thanks to the study of a single layer of bubbles (2D foam). We propose a method for in situ measurement of the permeability of films by simple and fast study of the transient regime of coarsening in 2D foam. We observed a correlation between diffusion coefficient of gas and permeability.Finally we describe the results of a space experiment on wet foam aging at large times (volume liquid fraction higher than 30%), extremely difficult on Earth because of gravity drainage, and to which we participated.

A imunização transcutânea (TCI) é uma via atrativa para o desenvolvimento de vacinação livre de agulhas, atuando nas APCs da pele, podendo substituir algumas das imunizações convencionais, em termos de facilidade, segurança e eficácia. O presente estudo avaliou a resposta imune da TCI com proteína recombinante de leptospira LipL32, uma proteína altamente conservada em cepas patogênicas e potente candidata vacinal. A TCI com a LipL32 na região abdominal de C57BL-6 foi capaz de primar o sistema imune, suscitando resposta sistêmica com altos níveis de anticorpos contra o antígeno, após reforços subimunizantes, ID e Tc. O padrão de citocinas em cultivo de células do sangue total dos grupos imunizados indicou que a imunização Tc foi capaz de primar o sistema imune, tanto inato quanto adaptativo. O tratamento local ou a coadministração com surfactantes ou PEG não evidenciou ação emoliente ou adjuvante. A coadministração Tc da LipL32 com MPL-A levou a efeito moderador da reação pro-inflamatória, redirecionando a resposta adaptativa, tanto humoral quanto celular. / Transcutaneous immunization (TCI) offers an attractive pathway for the development of needle-free vaccination by acting on APCs of the skin, showing potential to replace conventional immunization, in terms of safety and efficacy. In this study we evaluated the immune response by TCI with recombinant protein of leptospira LipL32, a highly conserved protein among pathogenic strains, a potential vaccine candidate. TCI with LipL32 was evaluated in C57BL-6 mice abdominal region and was able to confer systemic response with high levels of antibodies after subimmunizing ID and Tc boosters. The pattern of cytokines in cell cultures from whole blood of immunized groups indicated that the TCI was able to prime the immune system, for both innate and adaptive response. Local treatment of the skin or coadministration with surfactants and PEG did not show an emollient and an adjuvant action. Co-administration of LipL32 with MPL-A influenced the antibody response as well as showed a moderating effect of the pro-inflammatory reaction, redirecting the adaptive response.

Neste trabalho foi estudada a degradação anaeróbia do alquilbenzeno linear sulfonado (LAS), um surfactante largamente utilizado na fabricação de detergentes e presente em águas residuárias domésticas e industriais. Para isso, foram utilizados dois reatores anaeróbios horizontais de leito fixo (RAHLF) preenchidos com diferentes materiais suporte para imobilização da biomassa: carvão vegetal (RAHLF1) e leito misto de argila expandida e espuma de poliuretano (RAHLF2). O inóculo usado foi lodo proveniente de reator anaeróbio de fluxo ascendente e manta de lodo (UASB) utilizado no tratamento de águas residuárias de suinocultura. Os reatores foram alimentados, numa primeira etapa, com esgoto sintético e, posteriormente, suplementados com 14 mg/L de LAS. O tempo de detenção hidráulica (TDH) utilizado foi de 12 horas. Foi possível constatar que a presença do surfactante na alimentação não afetou a remoção de matéria orgânica (DQO), próxima a 90% em ambos os reatores para afluente com DQO de 550 mg/L. Com o balanço de massa constatou-se que os reatores foram aptos a remover LAS em 30% no RAHLF1 e 35% no RAHLF2. Desse total, 28% e 27%, respectivamente, foram degradados biologicamente, após 343 dias de operação. O restante manteve-se adsorvido nos materiais suportes. O pH no efluente dos RAHLFs manteve-se constante e próximo a 7,0. Alcalinidade foi gerada, assim como ácidos voláteis, apresentando concentrações médias de 342 e 353 mgCaCO3/L e 27 e 24 mgHAc/L no RAHLF1 e RAHLF2, respectivamente, durante operação com 14 mg/L de LAS no afluente. Ácidos acético e propiônico foram observados nos reatores em concentrações de até 50 e 12 mg/L, respectivamente. Em ambos os reatores estiveram presentes microrganismos com morfologias semelhantes a Methanosarcina sp., Methanosaeta sp., bacilos, cocos e filamentos, entre outros. Utilizando-se técnicas de Biologia Molecular (PCR/DGGE) verificou-se, em ambos os reatores, ampla variedade populacional de microrganismos pertencentes aos Domínios Bacteria, Archaea e ao Grupo BRS. Os materiais suportes selecionaram o crescimento de diferentes populações microbianas. No entanto, para o RAHLF2, praticamente não ocorreu estratificação populacional para os dois suportes. No RAHLF1, algumas populações foram semelhantes às observadas no reator de leito misto e outras cresceram mais favoravelmente / The aim of this work was to study the anaerobic degradation of LAS (linear alquilbenzene sulphonate), which is a surfactant widely used in manufacture of detergents and commonly found in domestic and industrial wastewaters. For the experimental purpose it was used two horizontal anaerobic immobilized biomass (HAIB) reactors filled with different support materials for biomass immobilization, such as: vegetal coal (HAIB1) and a mix of expanded clay and polyurethane foam (HAIB2). The biological material used as inoculum was obtained with the sludge of an upflow anaerobic sludge blanket reactor (UASB) treating suine wastewater. The reactors were fed, in a first stage, with synthetic sewage and, in a second, with a synthetic sewage supplemented with 14 mg/L of LAS. The applied hydraulic detention time was of 12 hours. With the chemical routine analyses it was possible to ascertain the evidence that the presence of surfactant in the feeding influent did not affect organic matter removal efficiencies (COD), which were close to 90% for both reactors treating 550 mg/L COD. The mass balance results suggested that the reactors removal efficiency of LAS were of 30% in RAHLF1 and 35% in RAHLF2. Of the total concentration of used LAS in the experiments, 28% and 27% were degraded biologically after 343 days of operating regime. The remaining LAS concentrations were adsorbed on the support materials. The pH values in the systems remained unaltered and close to 7.0. Alkalinity was generated (342 and 353 mgCaCO3/L, respectively), and volatile acids were recorded at concentrations of 24 and 27 mgHAc/L in RAHLF1 and RAHLF2, respectively, both treating effluent containing 14 mg/L of LAS. Acetic and propionic acids were detected in the reactors at concentrations up to 50 and 12 mg/L, for reactors 1 and 2, respectively. In both reactors it was observed microorganisms with morphologies resembling Methanosarcina sp., Methanosaeta sp., rods, cocus, filaments and others. Techniques of Molecular Biology (PCR/DGGE) showed high diversity of Bacteria, Archaea and BRS Group in both reactors. The support material selected different microbial populations. For RAHLF2, however, microbial stratification when using the distinct support material was not observed. In RAHLF1, it was observed that some populations were similar within the reactor of mixing bed where others grew more favorably

Zeólitas sintetizadas a partir de cinzas leves e pesadas de carvão e modificadas com hexadeciltrimetilamônio (HDTMA) foram usadas como adsorvente para remoção dos corantes Solophenyl Navy (SN) e Solophenyl Turquesa (ST) e suas formas hidrolisadas, Solophenyl Navy hidrolisada (SNH) e Solophenyl Turquesa hidrolisada (STH), de efluente simulado de indústria têxtil. As zeólitas leve modificada (ZLM) e pesada modificada (ZPM) foram caracterizadas por diferentes técnicas, tais como, espectrometria de fluorescência de raios-X, difração de raios-X e microscopia eletrônica de varredura. As ZLM e ZPM apresentaram carga estrutural negativa devido à formação de uma bicamada parcial de HDTMA na superfície externa da zeólita. A concentração inicial dos corantes, o tempo de contato e o equilíbrio de adsorção foram avaliados. A cinética de adsorção de SN, ST, SNH e STH sobre as zeólitas seguiu o modelo de pseudo segunda- ordem. O tempo de equilíbrio foi de 20 min para SN e ST e 30 min para SNH e STH sobre ZLM, enquanto sobre ZPM foi de 60 min para SN e ST e 20 e 30 min para SNH e STH, respectivamente. Os modelos de Langmuir, Freundlich e Temkin foram aplicados para descrever as isotermas de adsorção. A adsorção dos corantes foi melhor descrita pelo modelo de Langmuir, com exceção dos sistemas SN/ZPM, SNH/ZPM e SNH/ZLM que seguiram modelo de Freundlich. As capacidades máximas de adsorção foram 3,64; 3,57; 2,91 e 4,93 mgL-1 para SN, ST, SNH e STH pela ZLM, respectivamente e 0,235; 0,492; 1,26 e 1,86 mgL-1 pela ZPM, nesta mesma ordem. O melhor desempenho dos corantes hidrolisados foi atribuído à redução do tamanho das moléculas dos corantes durante o processo de hidrólise. A toxicidade aguda dos corantes foi avaliada por diferentes organismos teste. O microcrustáceo C. dubia apresentou valores de EC50 de 1,25; 54,5; 0,78 e 2,56 mgL-1 para SN, ST, SNH e STH, respectivamente. A macrófita L. minor mostrou valores de EC50 de 18,9; 69,4; 10,9 e 70,9 mgL-1 para SN, ST, SNH e STH, respectivamente. As larvas de mosquitos C. tepperi mostraram valores de EC50 de 119 e 440 mgL-1 para a SN e ST, respectivamente. Com relação ao processo de adsorção, os efeitos agudos foram substancialmente reduzidos após o tratamento da solução aquosa de SN e ST com ZLM, assim como de suas formas hidrolisadas, apresentando nenhuma toxicidade após a remoção de 100% da cor. Após o tratamento dos corantes com ZPM houve um aumento da toxicidade, com exceção dos corantes SNH e STH que não apresentaram toxicidade após o tratamento. Testes de Avaliação e Identificação da Toxicidade foram realizados a fim de identificar quais substâncias estariam causando a toxicidade nos corantes SN, ST e no lixiviado de ZLM e ZPM. Os efeitos tóxicos foram reduzidos significativamente após a manipulação com Extração de Fase Sólida (SPE) e ácido etilenodiaminotetracético (EDTA) para o lixiviado de ZLM e ZPM. Os corantes mostraram redução na toxicidade após a manipulação com EDTA indicando que as substâncias tóxicas eram principalmente metais catiônicos. / Zeolites synthesized from fly and bottom ashes and modified with hexadecyltrimethylamonium (HDTMA) were used as adsorbent to remove dyes - Solophenyl Navy (SN) and Solophenyl Turquoise (ST) and their hydrolysed forms Solophenyl Navy Hydrolysed (SNH) and Solophenyl Turquoise Hydrolysed (STH), from simulated textile wastewater. The HDTMA-modified fly zeolite (ZMF) and HDTMA-modified bottom zeolite (ZMB) were characterized by different techniques, as X-ray fluorescence spectrometry, X-ray diffraction and scanning electron microscopy, etc. The ZMF and ZMB presented negative charge probably due to the formation of a partial bilayer of HDTMA on exchangeable active sites on the external surface of unmodified zeolite. Initial dye concentration, contact time and equilibrium adsorption were evaluated. The adsorption kinetic for SN, ST, SNH and STH onto the zeolites followed the pseudo second-order model. The equilibrium time was 20 min for SN and ST and 30 min for SNH and STH, respectively. Langmuir, Freundlich and Temkin models were applied to describe the adsorption isotherms. Adsorption of the dyes were best described by the Langmuir model, with exception to SN/ZPM, SNH/ZPM and SNH/ZLM systems that followed Freundlich model. The maximum adsorption capacities were 3,64; 3,57; 2,91 e 4,93 for SN, ST, SNH e STH by ZLM, respectively and 0,235; 0,492; 1,26 e 1,86 by ZPM, in this order. The best performance for hydrolyzed dyes has been attributed to reduction of the size of dyes molecules during the hydrolysis process. Acute toxicity of the dyes to a different organism were evaluated by different test-organisms. Waterflea, Ceriodaphnia dubia showed EC50 value of 1,25; 54,5; 0,78 and 2,56 mgL-1 for SN, ST, SNH and STH, respectively. The plant Lemna minor showed EC50 values of 18,9; 69,4; 10,9 and 70,9 mgL-1 for SN, ST, SNH and STH, respectively. Midges larvae of Chironomus tepperi showed EC50 values of 119 and 440 mgL-1 for SN and ST, respectively. Regarding the adsorption process, acute effects were substantially reduced after adsorption treatment of aqueous solution with SN and ST by ZMF, as well as their hydrolysed forms, showing no toxicity after removal of 100% of colour. After treatment with ZPM there was an increase of the toxicity, with exception of SHN and STH dyes that do not show toxicity after the treatment. Toxicity Identification Evaluation tests (TIE) were realized in order to identify what substances were causing the observed toxicity for the SN, ST and the leached of ZMF and ZMB. The acute effects were significantly reduced after manipulation with Solid-Phase Extraction (SPE) and Ethylenediaminetetraacetic acid (EDTA) for the leached of ZMB and ZMF. The dyes showed reduced in the toxicity after manipulation with EDTA indicating that the toxicants are mostly cationic metals.

Estima-se que a mortalidade neonatal canina nas primeiras semanas de vida seja de 30%, em razão de diversas causas, dentre elas falhas de assistência neonatal. Em Medicina Humana, protocolos de assistência cardio-respiratória ao recém-nascido estão bem estabelecidos e são utilizados de rotina. Porém, os cuidados direcionados aos neonatos debilitados em Medicina Veterinária são, em geral, empíricos e passíveis de causar traumas e contusões. Deste modo, objetivou-se comparar o padrão do aparelho respiratório ao nascimento e a evolução durante a primeira hora de vida em neonatos nascidos em eutocia via vaginal ou cesariana eletiva; propor um protocolo de conduta para a avaliação do aparelho respiratório de neonatos nascidos em eutocia ou cesariana, por meio da auscultação cardio-torácica, do escore Apgar, hemogasometria, avaliação radiográfica pulmonar e da determinação do surfactante no líquido amniótico; relacionar o exame clínico geral com a avaliação específica do aparelho respiratório; estabelecer a análise de maior sensibilidade e especificidade na identificação de distúrbios respiratórios neonatais; quantificar os fosfolipídeos lecitina (L) e esfingomielina (E) no líquido amniótico; estabelecer a relação L/E, como indício de maturidade pulmonar. Utilizou-se 41 neonatos divididos em 2 grupos conforme a condição obstétrica: eutocia (1) ou cesariana eletiva (2). Foram avaliados o escore Apgar, temperatura corpórea e exame físico completo aos 0, 5 e 60 minutos pós-natal; hemogasometria venosa aos 0 e 60 minutos do nascimento e padrão radiográfico pulmonar ao nascimento. Houve significativo aumento dos valores de Apgar no decorrer da primeira hora de vida. Entretanto, o grupo 2 apresentou escore inferior ao nascimento e após 5 minutos. A temperatura corpórea neonatal apresentou significativa queda ao longo da primeira hora de vida, para ambos os grupos, com hipotermia após 5 e 60 minutos do nascimento. A auscultação pulmonar indicou irregularidade do padrão respiratório, presença de ruído respiratório de moderado a intenso e episódios de agonia respiratória, com evolução satisfatória ao longo da primeira hora de vida para ambos os grupos. Filhotes nascidos de cesariana apresentaram maior percentual de alterações radiográficas, com moderada a intensa opacificação pulmonar difusa, com pouca ou nenhuma definição da silhueta cardíaca e luz dos brônquios principais. Ao nascimento e após 1 hora, todos os neonatos apresentaram acidemia, sendo esta do tipo mista para o grupo 1 e do tipo respiratória para o grupo 2. Após 60 minutos houve parcial evolução do desequilíbrio ácido-básico em ambos os grupos. Não houve diferença estatística entre a relação L/E dos grupos 1 e 2 com valores de 7,29 (±3,55) e 5,89 (±4,87), respectivamente. Conclui-se que o padrão de análise do aparelho respiratório neonatal variou conforme a condição obstétrica; as variáveis de maior sensibilidade e especificidade para identificação de neonatos com distúrbios respiratórios ao nascimento foram auscultação torácica associada à avaliação hemogasométrica das variáveis pH e pCO2; os fosfolipídeos lecitina e esfingomielina presentes no líquido amniótico foram quantificados e a relação L/E estabelecida e indicou maturidade pulmonar independente da condição obstétrica. / Technical and scientific deficit related to veterinary neonatology is conspicuous. It is known that the canine mortality rate is up to 30% in the first weeks of life. In Human Medicine, neonatal cardio-respiratory assistance is well established and widely used. Thus, the objectives of the present study were to compare the respiratory system pattern at birth and its evolution during the first hour of life in puppies born through eutocia or cesarian section; to standardize neonatal respiratory system assessment under distinct obstetrics conditions; to correlate clinical general variables to the specific respiratory ones; to identify the most sensible and specific variables in order to attain neonatal respiratory diagnosis; to quantify the phospholipids lecithin (L) and sphingomielin (S) in amniotic fluid; to establish the L/S ratio and its correlation with lung maturity. Forty-one canine neonates were allocated into 2 groups according to the whelping condition: group 1 - eutocia and group 2 - elective cesarean section. The following assessments were performed at 0, 5 and 60 minutes after birth: Apgar score and rectal temperature. Venous hemogasometric evaluation was attained after birth and 1 hour later. Lung x-ray was performed between 0 and 5 minutes of life. Group 2 neonates showed lower vitality, with Apgar score significantly inferior at birth and after 5 minutes. Nevertheless, there was full satisfactory recovery at 5 minutes in both groups, with the Apgar score superior to 7. There was a significant reduction in rectal temperature with hypothermia at 5 and 60 minutes of birth in both groups. Respiratory pattern was irregular at lung auscultation, with mild to moderate sounds, but all neonates evolved properly among the first hour of life. Lung x-rays indicated relevant alterations in 17% of the puppies of group 1 and 30% of group 2. Cardiac silhouette and the main caudal bronchi were clearly visualized and the image of the thymus appeared like an enlarged domed volume in cranial mediastin, adjacent to the heart. The radiographic findings ranged from mild to moderate diffuse or restricted opacification of pulmonary parenchyma. Little or no definition of the cardiac silhouette, the main bronchi and the vagueness of the thymus were all findings consistent with pulmonary edema. All puppies presented acidemia at 0 and 60 minutes after birth, with partial recovery of the acid-base disorder in both groups during the first hour of life. L/S ratio was 7,29 (±3,55) for group 1 and 5,89 (±4,87) for group 2, with no statistical difference between them. In conclusion, obstetric condition influences neonatal respiratory pattern evaluation; lung auscultation associated with pH and pCO2 hemogasometric values, which were more sensible and specific to identify respiratory disorders at birth; lecithin and sphingomielin were quantified in the amniotic fluid; L/S ratio was established and indicated lung maturity regardless of the whelping condition.