There has been much discussion about the beneficial uses of lamellar graphite iron in piston rings–cylinder liner systems, where a good combinations of both thermal and tribological properties are essential. The excellent tribological performance of lamellar iron under such sliding conditions is principally associated with lubrication behaviour of the graphite particles which are distributed as lamellas throughout the matrix. During sliding, graphite particles are extruded and smeared onto the counterfaces, act as solid lubricating agents and form a thin graphite film between the sliding surfaces. Although this process especially, during the running-in period significantly changes the sliding wear response of the components, the exact mechanism behind of this phenomenon has rarely been discussed in previous studies. It is tribologically beneficial to keep the graphite open, particularly in applications where the scuffing issues do matter. In this thesis, the main causes involved in closing the graphite lamellas are discussed, with a focus on matrix plastic deformation that occurs during sliding. In first step, the relationship between graphite lamellae orientation and plastic deformation was investigated. To do so, two piston rings, belonging to the same two-stroke marine engine operated for different periods of time, were selected and compared to the unworn sample. The worn piston rings displayed a substantial decrease in both frequency and area fraction of the graphite lamellas. Most of the lamellas were closed as a result of plastic deformation of matrix. This happening was caused mainly by the interaction between abrasive particles and metallic matrix. Additionally, it was found that graphite lamellas parallel or near-parallel to the sliding direction exhibited maximum closing tendency under sliding condition. In next step, to have a better understanding of the graphite film formation mechanism and matrix deformation role in closing the graphite lamellas, microindentation and microscratch testing were performed on typical lamellar iron. The qualitative results showed a similar mechanism involving in graphite contribution to lubricate the sliding surfaces. Moreover, microindentations made nearby the graphite lamellas demonstrated that the deformation of the matrix causes the formation of cracks in the centre of the graphite lamellas, compressing and then extruding the graphite from its natural position, irrespective of the lamellas′ size. Furthermore, it was found that subsurface graphite orientation had a large influence on the extrusion behaviour, in that, for graphite lamellas oriented towards the indenter, the effect was observed more pronounced. Furthermore, an improved fully ferritic solution strengthened compacted graphite iron was produced for future wear studies. The effects of different Si levels and section thicknesses on tensile properties and hardness were investigated as well. The influence of Si content and section thickness on mechanical properties was revealed by improving the materials strength and slightly enhancing the hardness through increasing Si content. Besides, Si addition up to 4.5 wt% significantly affected the strength and elongation to failure of cast samples. / Helios / FFI

Volvo Cars in Skövde manufacture and assemble Volvo engines. When attaching the ignition coil to all 4-cylinder engines, a special mounting tool is required. This mounting tool is currently manufactured from injection-molded polyoxymethylene (POM), a thermoplastic. It has been noted that the life span of the tool is shortened as a result of abrasive wear that occurs during the attachment process of the ignition coil. An investigation of the possibility of manufacturing the mounting tool with a 3D-printer is undertaken in cooperation with ÅF, a consultant to Volvo Cars. A literature study is first presented to introduce broader knowledge on the subject. The abrasive wear and other material characteristics such as tensile strength, compressive strength and elongation of  POM and an alternative material for 3D-printing,  Ultem™, an amorphous thermoplastic polyetherimide are discussed.  These material characteristics are studied further and considered in tandem with both a theoretical analysis and a wear experiment, based on the pin-on-disc method. It is shown in the theoretical analysis that the wear is approximately six times larger for Ultem™ when compared to POM. The wear resistance of Ultem™ is highest when wear occurs parallel to the direction of the printed layers. In contrast, the experiment shows that the wear is about three times larger in Ultem™ than in POM.  The highest tensile strength of Ultem™ is also found in the direction of the printed layers. Some issues with the small elongation of the 3D-printed material are presented. It is recommended that ÅF apply the 3D-printing technique with Ultem™ only for construction details with complex geometries and where the material elongation will not exceed 5%. It is also recommended that ÅF both support and contribute to this innovative technique in order to develop leading edge competence in the subject. / Volvo Cars i Skövde tillverkar och monterar Volvomotorer. Vid monteringen av tändspolen till alla 4-cylindriga motorer behövs ett monteringsverktyg. Detta monteringsverktyg tillverkas för närvarande från formsprutad termoplast polyoximetylen (POM). Det har noterats att livslängden av verktyget förkortas på grund av abrasiv nötning som uppkommer under monteringsprocessen av tändspolen. Möjligheterna att tillverka monteringsverktyget med en 3D-skrivare utvärderas i samverkan med ÅF, en konsult till Volvo Cars. En litteraturstudie presenteras för att introducera en bredare kunskap i ämnet. Den abrasiva nötningen och materialegenskaper såsom draghållfasthet, tryckhållfasthet samt töjning hos POM och ett alternativt material för 3D-skrivning, Ultem™, en amorf termoplast polyeterimid, behandlas. Dessa materialegenskaper studeras vidare och tas i beaktning med både en teoretisk analys och ett nötningsexperiment, baserat på pin-on-disc metoden. Enligt den teoretiska analysen är nötningen hos Ultem™ approximativt 6 gånger större vid jämförelsen med POM. Nötningsbeständigheten hos Ultem™ är högst då nötning sker parallellt med 3D-skrivningsriktningen av lagren. Nötningsexperimenten visar att nötningen hos Ultem™ är ungefär 3 gånger större vid jämförelsen med POM. Den högsta draghållfastheten hos Ultem™ uppkommer också parallellt med 3D-skrivningsriktningen av lagren. Problem med den låga töjningen hos det 3D-skrivna materialet behandlas. ÅF rekommenderas att tillämpa 3D-skrivning med materialet Ultem™ främst för detaljer med komplexa geometrier med en töjning som inte överskrider 5 %. ÅF rekommenderas även att både stödja och bidra till denna innovativa teknik för att kunna skapa en ledande expertis i ämnet.

A fairly new technology used to produce metallic components is powder metallurgy (PM). Among the advantages with this technique are decreased cost of production for complex-shaped parts, new alloys are made possible, reduced end processing, less material loss, and vibrational damping effects. The downside is the number of pores created which can alter the tribological properties of the material. The focus of this report is to investigate how lean PM steel behaves under tribological contacts.  Friction and wear will be investigated using a pin-on-disc setup to mimic the sliding part of a gear tooth mesh. Previous studies show that the amount of wear, and if the wear increases or decreases with increased density is dependent on the degree of porosity and the pore size. This means that the wear might be minimized by optimizing the number of pores in the material and their shape and size. The result of this study shows that the friction coefficient decreases with increasing density. The wear coefficient show signs of the same correlations but further tests are needed. The main wear comes from adhesive wear, with signs of abrasive wear. The amount of abrasive wear seems to increase with an increase in density, supporting previous studies claiming that pores can trap wear debris and decrease the number of abrasive particles in the contact.

No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de TiN-PVD. Em cada um desses aços, foram produzidas camadas nitretadas de diferentes estruturas e espessuras, e foram determinadas experimentalmente as curvas potencial início de formação de camada branca, para a nitretação a 520oC. Para o aço ferramenta AISI H13, o emprego de tempos de pré-tratamento de nitretação mais prolongados ( aproximadamente 11 h) foi necessário para aprofundar a camada nitretada e, conseqüentemente, aumentar a capacidade de suportar carregamento dos revestimentos, evitando a formação de bordas que provocam o lascamento e a escamação das camadas de TiN. Observou-se que esse tipo de falha persiste se a zona de endurecimento for pouco profunda, uma vez que a transição de propriedades mecânicas da camada de TiN para o núcleo não nitretado continua abrupta e a capacidade de suportar carregamento da camada nitretada ainda é baixa. Por outro lado, curtos tempos de nitretação (aproximadamente 42 min.) foram suficientes para aumentar a aderência das camadas de TiN ao aço ferramenta D2, pois o núcleo não nitretado desse aço possui uma capacidade de suportar carregamento razoável. Observou-se que a resistência ao desgaste microabrasivo e a aderência dos revestimentos são prejudicadas com a presença de uma camada preta na interface camada de TiN/camada nitretada. Quando a superfície dos revestimentos é carregada, falhas do tipo “casca de ovo" facilmente ocorrem. / In this work, the influence of both the microstructure and the load-bearing capacity of nitrided layers, formed on top of AISI D2 and AISI H13 tool steels, on adhesion and wear resistance of PVD-TiN coatings was studied. The threshold nitriding potential curves for the above mentioned steels and the optimum conditions of the pre-treatments which increased the adhesion as well as the wear resistance of the PVD-TiN were determined experimentally. By using longer nitriding times (about 11 h) and lower nitrogen contents in the gas mixture (about N2-5%vol.), it was possible to minimize the pile-up degree of the TiN/H13 nitrided substrates and, consequently, the occurrence of coatings chipping. This flaw persists when the nitrided layer is thin, due to an abrupt transition of mechanical properties at the TiN coating / steel core interface. Shorter nitriding times (about 42 min.) and lower nitrogen contents (about N2-5%vol.), on the other hand, are sufficient to guarantee a better adhesion of TiN coatings on AISI D2 tool steel, as the core of such steel possesses relatively better load-bearing capacity than the AISI H13 tool steel. The presence of a black layer at the TiN/nitrided layer interface was observed in all coatings deposited over nitrided layers produced above the threshold nitriding potential curves. This layer affects adversely the wear resistance and the adhesion of the TiN coatings. When higher loads are applied on the coated surface, “egg shell" type flaws easily occur.

No presente trabalho foi avaliado o efeito da microestrutura e da capacidade de suportar carregamento de camadas nitretadas produzidas em aços ferramenta AISI H13 e AISI D2 sobre a aderência e a resistência ao desgaste microabrasivo de revestimentos de TiN-PVD. Em cada um desses aços, foram produzidas camadas nitretadas de diferentes estruturas e espessuras, e foram determinadas experimentalmente as curvas potencial início de formação de camada branca, para a nitretação a 520oC. Para o aço ferramenta AISI H13, o emprego de tempos de pré-tratamento de nitretação mais prolongados ( aproximadamente 11 h) foi necessário para aprofundar a camada nitretada e, conseqüentemente, aumentar a capacidade de suportar carregamento dos revestimentos, evitando a formação de bordas que provocam o lascamento e a escamação das camadas de TiN. Observou-se que esse tipo de falha persiste se a zona de endurecimento for pouco profunda, uma vez que a transição de propriedades mecânicas da camada de TiN para o núcleo não nitretado continua abrupta e a capacidade de suportar carregamento da camada nitretada ainda é baixa. Por outro lado, curtos tempos de nitretação (aproximadamente 42 min.) foram suficientes para aumentar a aderência das camadas de TiN ao aço ferramenta D2, pois o núcleo não nitretado desse aço possui uma capacidade de suportar carregamento razoável. Observou-se que a resistência ao desgaste microabrasivo e a aderência dos revestimentos são prejudicadas com a presença de uma camada preta na interface camada de TiN/camada nitretada. Quando a superfície dos revestimentos é carregada, falhas do tipo “casca de ovo” facilmente ocorrem. / In this work, the influence of both the microstructure and the load-bearing capacity of nitrided layers, formed on top of AISI D2 and AISI H13 tool steels, on adhesion and wear resistance of PVD-TiN coatings was studied. The threshold nitriding potential curves for the above mentioned steels and the optimum conditions of the pre-treatments which increased the adhesion as well as the wear resistance of the PVD-TiN were determined experimentally. By using longer nitriding times (about 11 h) and lower nitrogen contents in the gas mixture (about N2-5%vol.), it was possible to minimize the pile-up degree of the TiN/H13 nitrided substrates and, consequently, the occurrence of coatings chipping. This flaw persists when the nitrided layer is thin, due to an abrupt transition of mechanical properties at the TiN coating / steel core interface. Shorter nitriding times (about 42 min.) and lower nitrogen contents (about N2-5%vol.), on the other hand, are sufficient to guarantee a better adhesion of TiN coatings on AISI D2 tool steel, as the core of such steel possesses relatively better load-bearing capacity than the AISI H13 tool steel. The presence of a black layer at the TiN/nitrided layer interface was observed in all coatings deposited over nitrided layers produced above the threshold nitriding potential curves. This layer affects adversely the wear resistance and the adhesion of the TiN coatings. When higher loads are applied on the coated surface, “egg shell” type flaws easily occur.