[pt] Os efluentes industriais dos processos de mineração e metalurgia extrativa, podem conter variáveis teores de As, Se, Sb e Bi tornando-se uma fonte potencial de poluição. O presente trabalho teve como objetivo estudar a remoção de As, Se, Sb e Bi presentes na mesma solução aquosa, por precipitação química empregando íons de agentes precipitantes, em condições oxidantes e reduzidas. Para isso, foram empregadas soluções sintéticas mistas dos analitos. As variáveis avaliadas foram: tipo de agente precipitante (Fe(III), Fe(II), Al(III) e Ca(II)), pH, relação molar agente precipitante/analito, concentração inicial de As, Se, Sb e Bi e a pré-oxidação destes elementos com H2O2. Para soluções contendo concentração inicial de 200 mg/L dos analitos sem pré-oxidação, foi possível atingir 99,95 por cento de eficiência de remoção e concentrações residuais de 0,11 mg/L, 0,10 mg/L, 0,08 mg/L, 0,01 mg/L para As, Se, Sb e Bi, respectivamente, por precipitação com Fe(III), a pH 5 em 30 minutos de reação e relação molar Fe(III)/As, Se, Sb e Bi = 7. Esses valores obtidos enquadram-se dentro do permitido pela resolução CONAMA 430/2011 para descarte de efluentes de As e Se. Sendo que o pH ótimo para precipitar As, Se, Sb e Bi depende do estado de oxidação de seus oxiânions, enquanto o agente precipitante Fe(III) foi bem superior ao Fe(II), Al(III) e Ca(II) para remover As, Se, Sb e Bi sem ou com pré-oxidação. A pré-oxidação desses elementos com H2O2 influenciou na remoção de As e Se, uma vez que o As foi bem melhor removido com pré-oxidação e Se sem pré-oxidação. Já o Sb e Bi não foram influenciados pela pré-oxidação. A relação molar ótima de Fe(III)/As, Se, Sb e Bi foi de 5 e 7 Finalmente as micrografias obtidas por MEV mostram uma estrutura compacta aglomerada de tamanho irregular, variando de protuberância de várias dezenas de mícrons e, a análise semiquantitativa mostrou que estão constituídos principalmente pelos elementos As, Se, Sb, Bi, Fe, O, Cl e Na, estando Fe e O em maior quantidade. / [en] The industrial effluents from mining and extractive metallurgy processes may contain varying amounts of As, Se, Sb and Bi becoming a potential source of pollution. The object of the present work was to investigate the removal of As, Se, Sb and Bi present in the same aqueous solution, by chemical precipitation using cations of precipitating agents, under oxidizing and reduced conditions. For this, mixed synthetic solutions. The variables evaluated were: precipitating agent type (Fe (III), Fe (II), Al (III) and Ca (II)), pH, precipitating /analytes molar ratio, initial concentration of As, Se, Sb and Bi And the preoxidation of these elements with H2O2. For solutions containing the initial concentration of 200 mg / L of the analytes without pre-oxidation, it was possible to achieve 99.95 percent removal efficiency and residual concentrations of 0.11 mg / L, 0.10 mg / L, 0.08 mg / L, 0.01 mg / L for As, Se, Sb and Bi, respectively, by Fe (III) precipitation, at pH 5 in 30 minutes of reaction and Fe (III) / As, Se, Sb and Bi = 7. These values are within the limits allowed by CONAMA Resolution 430/2011 for the disposal of As and Se effluents. The optimum pH to precipitate As, Se, Sb and Bi depends on the oxidation state of its oxyanions, while the Fe (III) precipitating agent was well above Fe (II), Al (III) and Ca (II) to remove As, Se, Sb and Bi. Pre-oxidation of these elements with H2O2 influenced the removal of As and Se, however Sb and Bi were not influenced by pre-oxidation. The optimal molar ratio of Fe (III) / As, Se, Sb and Bi was 5 and 7 to precipitate these elements. Finally, the micrographs obtained by MEV show a compact agglomerated structure, and the semiquantitative analysis showed that they are constituted mainly by elements As, Se, Sb, Bi, Fe, O, Cl and Na , With Fe and O being in greater quantity.

Submitted by Pedro Silva Filho (pfsilva@ipen.br) on 2017-11-22T17:15:11Z No. of bitstreams: 0 / Made available in DSpace on 2017-11-22T17:15:11Z (GMT). No. of bitstreams: 0 / O excessivo processo de urbanização da Região Metropolitana de São Paulo resultou na perda das características naturais dos seus cursos d\'água ocasionando profundas alterações nos regimes de vazão e de qualidade. O objetivo desse estudo foi avaliar a concentração de metais tóxicos, os semi-metais As, Sb e Se e os elementos terras raras, presentes em amostras de sedimento superficiais coletadas nos Reservatórios Billings, Guarapiranga e Rio Grande. Os elementos Ag, Al, As, Ba, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sb, Se e Zn foram determinados pela técnica de Espectrometria de Emissão Ótica com Plasma Indutivamente Acoplado (ICP OES). Alguns elementos maiores, traço e elementos terras raras (Ce, Eu, La, Lu, Nd, Sm, Tb e Yb) foram determinados pela técnica de Análise por Ativação Neutrônica Instrumental (INAA). A concentração de Hg total foi determinada pela técnica Espectrometria de Absorção Atômica com Geração de Vapor Frio (CVAAS). A validação das metodologias foi realizada por meio da análise de materiais de referência certificados. Para avaliar as possíveis fontes de contaminação antrópicas foram utilizadas as ferramentas de fator de enriquecimento (FE) e o índice de geoacumulação (IGeo). Os resultados obtidos pelas técnicas foram comparados com os valores orientadores TEL e PEL estabelecidos pelo CCME (Canadian Council of Ministers of the Environment) e adotados pela CETESB. Todos os pontos analisados apresentaram valores > TEL para todos os metais e dois pontos da represa Billings (BILL02100 e 02030), valores > PEL para As, Cr, Cu, Hg, Ni, Pb e Zn, provavelmente em decorrência do recebimento das águas do Rio Pinheiros e das bacias de drenagem do ribeirão Cocaia e Bororé. Os valores de FE e IGeo calculados apontaram possíveis contaminações antrópicas para Sb e Se para os elementos determinados por ICP OES e de As, Cr, Sb e Zn, por INAA. O reservatório Billings apresentou, em geral, as maiores concentrações para os elementos analisados, indicando uma má qualidade de seus sedimentos. Este estudo confirma a necessidade de um monitoramento frequente da qualidade do sedimento nos reservatórios estudados como procedimento indispensável para avaliação periódica da qualidade das bacias, considerando sua importância no fornecimento de água para a Região Metropolitana de São Paulo. / Dissertação (Mestrado em Tecnologia Nuclear) / IPEN/D / Instituto de Pesquisas Energéticas e Nucleares - IPEN-CNEN/SP

Procedimentos analíticos espectrofotométricos foram desenvolvidos empregando etapas de separação e pré-concentração em sistemas de análises em fluxo com multi-impulsão ou lab-in-syringe, com aplicação a amostras de interesse agronômico (ferro em materiais vegetais e alimentos) e ambiental (cianeto dissociável em ácidos, ferro e antimônio em águas). A determinação de cianeto explorou a descoloração do complexo formado entre Cu(I) e ácido 2-2´-biquinolino-4,4´-dicarboxílico (BQA) pela presença de CN-, após a separação de HCN por difusão gasosa. Espectrofotometria com longo caminho óptico foi empregada para aumentar a sensibilidade, com resposta linear entre 5 e 200 g L-1, limite de detecção, coeficiente de variação (n = 10) e frequência de amostragem de 2,0 g L-1, 1,5% e 22 h-1, respectivamente. O procedimento consumiu apenas 48 ng de Cu(II), 5,0 g de ácido ascórbico e 0,9 g de BQA por determinação e gerou 2,6 mL de efluente. Tiocianato, nitrito e sulfito não afetaram a determinação de cianeto e peróxido de hidrogênio evitou a interferência de sulfeto até 200 g L-1. Os resultados para as amostras de águas naturais foram concordantes com o procedimento fluorimétrico em fluxo com 95% de confiança. Novas estratégias foram propostas para a extração em ponto nuvem (EPN) em fluxo: (i) a fase rica em surfactante foi retida diretamente na cela de fluxo, evitando a diluição; (ii) microbombas solenoide foram exploradas para melhorar a mistura e modular a vazão na retenção e remoção da fase rica, evitando a eluição com solvente orgânico e (iii) o calor liberado e os sais fornecidos por uma reação de neutralização em linha foram explorados para indução do ponto nuvem, sem dispositivo externo de aquecimento. Estas inovações foram demonstradas pela determinação espectrofotométrica de ferro baseada no complexo com 1-(2-tiazolilazo)-2-naftol (TAN). Resposta linear foi observada entre 10 e 200 g L-1, com limite de detecção, coeficiente de variação e frequência de amostragem de 5 g L-1, 2,3% (n = 7) e 26 h-1, respectivamente. O fator de enriquecimento foi de 8,9 com consumo apenas de 6 g de TAN e 390 g de Triton X-114 por determinação. Os resultados para amostras de águas foram concordantes com o procedimento de referência e os obtidos para digeridos de materiais de referência de alimentos concordaram com os valores certificados. A determinação espectrofotométrica de antimônio foi realizada explorando pela primeira vez a EPN em sistema lab-in-syringe. O complexo iodeto e antimônio forma um par iônico com H+, que pode ser extraído com Triton X-114. Planejamento fatorial demonstrou que as concentrações de ácido ascórbico, H2SO4 e Triton X-114, bem como as interações de segunda e de terceira ordem foram significativas (95% de confiança). Planejamento Box-Behnken foi aplicado para a identificação dos valores críticos. Robustez com 95% de confiança, resposta linear entre 5 e 50 g L-1, limite de detecção, coeficiente de variação (n = 5) e frequência de amostragem foram estimados em 1,8 g L-1, 1,6% e 16 h-1, respectivamente. Os resultados para amostras de águas naturais e medicamentos anti-leishmaniose foram concordantes com os obtidos por espectrometria de absorção atômica com geração de hidretos (HGFAAS) com 95% de confiança / Spectrophotometric analytical procedures were developed by exploiting separation and preconcentration steps in flow systems based on multi-pumping or lab-in-syringe approaches with application to agronomic (iron in plant materials and food) and environmental samples (acid dissociable cyanide, iron and antimony in waters). Cyanide determination exploited bleaching of the Cu(I)/2,2\'-biquinoline 4,4\'-dicarboxylic acid (BCA) complex by the analyte, after separation of HCN by gas diffusion. Long path length spectrophotometry was successfully exploited to increase sensitivity, thus achieving a linear response from 5 to 200 g L-1, with detection limit, coefficient of variation (n = 10) and sampling rate of 2 g L-1, 1.5% and 22 h-1, respectively. Each determination consumed 48 ng of Cu(II), 5 g of ascorbic acid and 0.9 g of BCA. As high as 100 mg L-1 thiocyanate, nitrite or sulfite did not affect cyanide determination and sample pretreatment with hydrogen peroxide avoided sulfide interference up to 200 g L-1. The procedure is environmentally friendly and presented one of the lowest detection limits associated to high sampling rate. The results for freshwater samples agreed with those obtained with the flow-based fluorimetric procedure at the 95% confidence level. Novel strategies were proposed for on-line cloud point extraction (CPE): (i) the surfactant-rich phase was retained directly into the flow cell to avoid dilution prior to detection; (ii) solenoid micro-pumps were explored to improve mixing and for flow modulation in the retention and removal of the surfactant-rich phase, thus avoiding the elution step with organic solvents and (iii) the heat released and the salts provided by an on-line neutralization reaction were exploited to induce cloud point without an external heating device. These approaches were demonstrated for the spectrophotometric determination of iron based on complex formation with 1-(2-thiazolylazo)-2-naphtol (TAN). A linear response was observed from 10 to 200 g L-1, with detection limit, coefficient of variation, and sampling rate of 5 g L-1, 2.3% (n = 7) and 26 h-1, respectively. The enrichment factor was 8.9 and the procedure consumed only 6 g of TAN and 390 g of Triton X-114 per determination. The results for freshwater samples agreed with the reference procedure and those obtained for certified reference materials of food agreed with the certified values. Spectrophotometric determination of antimony was performed for the first time exploiting CPE in the lab-in-syringe system. The antimony/iodide complex forms an ion-pair with H+, which can be extracted with Triton X-114. Factorial design showed that the concentrations of ascorbic acid, H2SO4 and Triton X-114, as well as the second and third order interactions were significant (95% confidence). The Box-Behnken design was applied to identify the critical values. The system is robust with 95% confidence and a linear response was observed from 5 to 50 g L-1, with detection limit, coefficient of variation (n = 5) and sampling rate of 1.8 g L-1, 1.6% and 16 h-1, respectively. The results for water samples and antileishmanial drugs agreed with those obtained by hydride generation atomic absorption spectrometry at the 95% confidence level

Abstract Pollutant (such as metals and sulphate) contamination exists in the wastewaters of many industries, including mining operations, metal plating facilities, and tanneries. Adsorption is one of the most commonly used processes for the removal of pollutants from waters and wastewaters due to its high efficiency and simple operation. Activated carbon is the most frequently used adsorbent material, although its high cost inhibits its widespread use in wastewater treatment. Therefore, there is a need to develop other adsorbents from alternative inexpensive raw materials such as locally available industrial and mineral waste and by-products. The aim of this thesis was to study the possibility of using industrial waste materials such as carbon residue, metakaolin, blast-furnace slag and analcime as an inexpensive sorbent for iron, copper, nickel, arsenic, antimony and sulphate removal from aqueous solutions. To enhance their adsorption capacity, different chemical treatments (i.e. activation, modification, geopolymerisation) were performed. As a result, the level of removal of iron, copper and nickel by carbon residue and zinc chloride activated carbon residue was higher than that by the commercial activated carbon. Iron chloride modified carbon residue was the most effective sorbent material for sulphate removal when compared to the other studied chemically modified/activated carbon residues. Blast-furnace slag and metakaolin geopolymers as well as their raw materials, were examined for the simultaneous removal of nickel, arsenic and antimony from the spiked mine effluent. In the case of blast-furnace slag, geopolymerisation clearly increased the efficiency of nickel, arsenic and antimony removal to a beneficial level. The barium chloride modified blast-furnace-slag geopolymer was a very efficient sorbent material for sulphate removal and it could thus be a technically feasible sulphate sorbent for wastewater treatment (e.g. in the mining industry in applications in which very low sulphate levels are desired). Barium chloride modified acid washed analcime could also be a potential sorbent for sulphate removal. / Tiivistelmä Teollisuuden jätevedet kuten kaivosvedet ja metalliteollisuuden prosessien jätevedet voivat sisältää monenlaisia haitallisia ja jopa myrkyllisiä aineita kuten metalleja ja sulfaattia. Adsorptiota käytetään yleisesti esimerkiksi metallien ja orgaanisten yhdisteiden poistossa vesiliuoksista, koska se on tehokas ja yksinkertainen menetelmä. Aktiivihiili on yleisimmin käytetty adsorbenttimateriaali vedenpuhdituksessa, mutta sen hinta joissain tapauksissa rajoittaa sen käyttöä. Tämän vuoksi on tarvetta kehittää vaihtoehtoisia adsorbenttimateriaaleja edullisista raaka-aineista. Viime vuosien aikana on raportoitu mm. teollisuus- ja mineraalijätteistä, joita voidaan hyödyntää vesien ja jätevesien puhdistuksessa. Tämän työn tavoitteena oli hyödyntää teollisuudesta muodostuvia jätemateriaaleja (hiilijäännös, metakaoliini, masuunikuona ja analsiimi) raudan, kuparin, nikkelin, arseenin, antimonin tai sulfaatin poistossa malli- ja jätevesistä. Materiaaleja käsiteltiin erilaisilla kemikaaleilla (aktivointi, modifiointi tai geopolymerointi), jotta niiden adsorptiotehokkuudet paranisivivat poistettavia aineita kohtaan. Tulokset osoittivat, että raudan, kuparin ja nikkelin poisto oli sekä käsittelemättömällä että sinkkikloridilla aktivoidulla hiilijäännöksellä korkeampi kuin kaupallisella aktiivihiilellä. Arseenin, nikkelin ja antimonin poistoa kaivosvedestä tutkittiin masuunikuona- ja metakaoliinigeopolymeereillä, joista masuunikuonageopolymeeri osoittautui tehokkaimmaksi metallien poistajaksi. Bariumkloridilla modifioitu masuunikuonageopolymeeri puolestaan poisti erittäin tehokkaasti sulfaattia kaivoksen jätevedestä. Rautakloridilla modifioitu hiilijäännös ja happopesty bariumkloridilla modifioitu analsiimi osoittatuivat myös lupaavaksi materiaaliksi sulfaatin poistossa.

Abstract This thesis examines three different areas of water treatment technology: the application of organic peracids in wastewater treatment; the removal of organic residues from boiler make-up water; and the use of geopolymers as sorbents. The main advantages of peracids as alternative wastewater disinfectants are their effective antimicrobial properties and high oxidation power, as well the absence of harmful disinfection by-products after their use. Performic, peracetic and perpropionic acids were compared in laboratory-scale disinfection, oxidation and corrosion experiments. From the techno-economical point of view, performic acid proved to be the most effective disinfectant against E. coli and fecal enterococci. However, in the bisphenol-A oxidation experiments, no advantages compared to hydrogen peroxide use were observed. It was also determined that corrosion rates on stainless steel 316L were negligible, while carbon steel seemed unsuitable in terms of corrosion for use with peracids even in low concentrations. Organic compounds in the boiler plant water-steam cycle thermally decompose and form potentially corrosive species. Activated carbon filtration was confirmed to be a suitable method for the removal of organic residue from deionized boiler make-up water. No significant differences in terms of treatment efficiency between commercial activated carbons were observed. However, acid washing as a pre-treatment reduced the leaching of impurities from new carbon beds. Nevertheless, a mixed-bed ion exchanger was required to remove leached impurities, such as silica and sodium. Geopolymers, or amorphous analogues of zeolites, can be used as sorbents in the treatment of wastewater. Metakaolin and blast-furnace-slag geopolymers showed positive potential in the treatment of landfill leachate (NH4+ ) and mine effluent (Ni, As, Sb). / Tiivistelmä Tämä väitöskirja käsittelee kolmea erillistä vedenkäsittelyteknologian osa-aluetta: orgaanisten perhappojen käyttöä jäteveden käsittelyssä, orgaanisten jäämien poistoa suolavapaasta kattilalaitoksen lisävedestä ja geopolymeerien sovelluksia vedenkäsittelysorbentteina. Orgaanisten perhappojen pääasialliset edut verrattuna kilpaileviin tekniikoihin ovat hyvä desinfiointiteho, korkea hapetuspotentiaali ja desinfioinnin sivutuotteiden muodostumattomuus. Permuurahais-, peretikka- ja perpropaanihapon vertailu osoitti permuurahaishapon olevan kemikaaleista tehokkain E. coli - ja enterokokkibakteerien inaktivoinnissa kustannus- ja teknisistä näkökulmista. Hapetuksessa, jossa käytettiin bisfenoli-A:ta malliaineena, ei kuitenkaan havaittu etua verrattuna edullisempaan vetyperoksidiin. Ruostumattoman teräksen (316L) pinnalla ei havaittu merkittävää korroosiota, kun taas hiiliteräs ei sovellu käytettäväksi perhappojen kanssa. Orgaaniset jäämät kattilalaitoksen vesi-höyrykierrossa hajoavat termisesti pienen moolimassan hapoiksi ja aiheuttavat korroosioriskin. Aktiivihiilisuodatuksen todettiin olevan soveltuva menetelmä orgaanisten jäämien poistoon lisävedestä. Aktiivihiililaatujen välillä ei havaittu merkittäviä eroja, mutta happopesu aktiivihiilen esikäsittelynä vähensi hiilestä liukenevien epäpuhtauksien määrää. Geopolymeerit ovat zeoliittien amorfisia analogeja ja niiden ioninvaihtokykyä voidaan hyödyntää vedenkäsittelysovelluksissa. Metakaoliini- ja masuunikuonapohjaisten geopolymeerien todettiin olevan lupaavia materiaaleja malliliuosten, kaatopaikan suotoveden ja kaivoksen purkuveden käsittelyssä poistettaessa ammoniumia, nikkeliä, arseenia ja antimonia.

The implementation of energy storage systems in the current electrical grid will increase the grid's reliability and e ciency. Room temperature sodium batteries are seen as potential technology, especially to assist renewable energy generation sources. Currently, suggested negative electrode materials, however, are still not satisfactory for practical use in terms of fabrication costs, gravimetric /volumetric energy densities, cyclability, and irreversible capacity losses occur at the rst cycle. The literature describes various strategies that enhance the specific capacity and/or the cyclability of negative electrode materials but all involve increasing the fabrication costs due to the chosen synthesis or the complexity of the electrode's design. Furthermore, strategies, that reduce the irreversible capacity loss at first cycle, are not discussed. In this present experimental research work, presodiating bulk metallic negative electrode materials prior to cycling, prepared via a simple, cheap and easy-to-scaleup synthesis route, is introduced as a new strategy to improve the cyclability and to effectively reduce the first cycle irreversible capacity loss. Electrochemical and structural experiments were carried out to investigate sodiumtin-antimony powders. Presodiating mechanically bulk Sn-Sb negative electrode materials e ectively reduces the irreversible capacity loss at first cycle and enhances the specific capacity when compared to the non-presodiated powder, while the proper choice of electrode composite and electrolyte formulation improves the cycle life of the electrodes. The enhancement of the electrochemical properties of the presodiated NaSnSb powder, composed of the ternary phase Na5Sb3Sn and an unknown ternary phase crystallising in a hexagonal setting P6, is associated with the stabilisation of the SnSb as desodiation product. Presodiating bulk SnSb negative electrode material is a viable strategy to reduce the first cycle irreversible capacity loss, alleviating the volume changes. With an optimised system, this approach may be extended to other negative electrode materials, reducing the fabrication costs of high capacity negative electrode materials for room temperature sodium batteries. Presodiated NaSnSb negative electrode material may be combined with non-sodiated positive electrode material, such as sulphur to develop competitive room temperature sodium-sulphur batteries. / Die Implementierung von Energiespeichersystemen im bereits bestehenden Stromnetz ist eine der Lösungen, um die Zuverlässigkeit und die Effizienz des Netzes zu nutzen. Raumtemperatur Natrium-Batterien gelten als erfolgsversprechende Technologie insbesondere zur Unterstützung erneuerbarer Energieerzeugungsquellen. Jedoch sind die naheliegenden negativen Elektrodenmaterialien für eine praktische Anwendung hinsichtlich Herstellungskosten, gravimetrischer oder volumetrischer Energiedichte, Zyklenfestigkeit und irreversiblen Kapazitätsverlusten im ersten Zyklus noch nicht zufriedenstellend. Die Literatur beschreibt verschiedene Strategien, die die spezifische Kapazität und / oder die Zyklenfestigkeit von negativen Elektrodenmaterialien verbessern. Diese führen jedoch alle zu einer Erhöhung der Herstellungskosten aufgrund der gewählten Synthese oder des Designs der komplexierten Elektrode. Darüber hinaus werden Strategien zur Reduzierung des irreversiblen Kapazitätsverlusts im ersten Zyklus nicht erörtert. Diese experimentelle Forschungsarbeit präsentiert mit Natrium angereicherte metallische negative Elektrodenmaterialien vor der Wechselbeanspruchung/dem periodischen Durchlaufen, die durch einen schlichten, billigen und einfach zu skalierenden Syntheseweg hergestellt wurden, als eine neue Strategie zur Verbesserung der Zyklenfestigkeit und zur wirksamen Verringerung des irreversiblen Kapazitätsverlusts im ersten Zyklus. Elektrochemische und strukturelle Experimente wurden durchgeführt, um mit Natrium angereichertes Zinn-Antimon-Pulver zu untersuchen. Die mechanischen mit Natrium angereichertes Sn-Sb-negativen Elektrodenmaterialien verringert effektiv den irreversiblen Kapazitätsverlust im ersten Zyklus und erhöht die spezische Kapazität im Vergleich zu dem ohne Natrium angereicherte Pulver, während die richtige Wahl der Elektrodenzusammensetzung und der Elektrolytformulierung die Lebenszyklus der Elektroden verbessert. Die Verbesserung der elektrochemischen Eigenschaften des mit Natrium angereicherten NaSnSb-Pulvers, bestehend aus der ternären Phase Na5Sb3Sn und einer unbekannten ternären Phase, die in einer hexagonalen Aufbau P6 kristallisiert, ist mit der Stabilisierung des Enddesodiationsproduktes beim periodischen Zyklus verbunden, wobei das intermetallische SnSb nach Rekristallisation vorliegt. Mit Natrium angereicherte SnSb negativen Elektrodenmaterialien sind eine tragfähige Strategie zur Verringerung des irreversiblen Kapazitätsverlustes im ersten Zyklus, die Volumenänderungen abschwächen. Mit einem optimierten System kann dieser Ansatz auf andere negative Elektrodenmaterialien erweitert werden um die Herstellungskosten von negativen Elektrodenmaterialien mit hoher Kapazität für Raumtemperatur-Natrium-Batterien zu verringern. Mit Natrium angereichertes NaSnSb-negatives Elektrodenmaterial kann mit nicht mit Natrium versetztem positivem Elektrodenmaterial wie Schwefel kombiniert werden, um realisierbare Raumtemperatur Natrium-Schwefel-Batterien zu entwickeln.

Climate change is a subject of deep distress in today’s world. Over dependence on hydrocarbon has resulted in serious environmental problems. Rising sea level, global warming and ozone layer depletion are the mainstream of any discuss world over. The collective goal of cutting carbon emission by the year 2020has prompted the search for clean, alternative energy sources. This effort are already yielding good reward as other forms of energy such as solar, wind, nuclear and hydro have received huge investment and renew interest over the past decade. Thermoelectric materials over the past decades have been tipped to replace conventional means of power generations as these materials have the ability to convert heat to electrical energy and vice versa. They are simple, have no moving parts and use no greenhouse gases. But the major drawback of these materials is their low conversion efficiency. Hence there is a need to enhance the efficiency of thermoelectric material to fulfill their undeniable potentials. A parameter called the thermoelectric figure of merit, ZT defines the efficiency of a thermoelectric material. ZT relates three non-mutually exclusive transport properties namely Seebeck coefficient, electrical conductivity and thermal conductivity. Efficient thermoelectric material should possess high Seebeck coefficient, high electrical conductivity and low thermal conductivity. Hence, one of the interesting ideas in the area of thermoelectric research is the concept of designing a bulk material with high density of phonon scattering centers so has to reduce the lattice contribution to thermal conductivity but at the same time have minimum impact oncharge carriers. This is usually achieved by utilizing interphase and grain boundaries which are localized defects to scatter phonons. The volume fraction of the grain/interphase boundaries can be control through phase modification and microstructure design. This thesis is centered on Bi-Sb-Te systems which are the present room temperature state of the earth thermoelectric material. The investigation revolves around developing a new kind of microstructure in the well-studied Bi-Sb-Te system that shows tremendous potential as a means to reduce lattice contribution to thermal conductivity. The idea of having both p and n-type thermoelectric material preferably from the same material was also a motivation in our investigation. The thesis isdivided into six chapters. The first chapter introduces the concept of thermoelectricity i.e. the direct conversion of thermal energy into electricity. The physics involved and contribution of individual to the science of thermoelectricity were enumerated. Efficiency, optimization and material selection for better thermoelectric performance were briefly enumerated. Prospective materials that are currently been investigated for better thermoelectric properties were also mentioned. The structure of the Bi-Sb-Te system which is the focus of this thesis is present in this chapter including doping effect on the thermoelectric performance of the system as well as the various methods present been employed to improve the thermoelectric properties of the system. Finally the chapter enumerates the scope and object of the present thesis. The different experimental procedures adopted in the present thesis arediscussed in chapter 2. The details of different processing routes followed to synthesize flame-melted ingots, flame-melted + low temperature milled (cryo milling) + spark plasma sintering (SPS) alloy and flame-melted + melt spinning + spark plasma sintering (SPS) alloy, are discussed followed by the various structural and functional characterization techniques. The unique advantage of the spark plasma sintering techniques over the conventional sintering method was talked out in detail. The structural characterizations performed on the synthesized alloys include XRD, SEM and whilethe functional characterizations comprised of Hall measurement, Seebeck coefficient, electrical resistivity and thermal conductivity measurements. Thermoelectric properties of selected composition of Bi-Sb-Te synthesized via flame-melting are presented in chapter 3.Detail study of four analyzed compositions namelyBi24Sb20Te56, Bi20Sb12Te69, Bi16Sb5Te79 and Bi29Sb11Te60resulted in four unique microstructure and different volume fraction of primary and secondary phases. The resultant morphologies of the microstructure were observed to have influence the thermoelectric behavior corresponding to each composition. The sole influence of anti-structural defects on the conductivity type and the role of microstructure morphologies and length scale were understood in this chapter. Samples with segregated Te and a solid solution BiSbTe3(eutectic morphology) form an n-type thermoelectric material while samples with only solid solution BiSbTe3 forms a p-type thermoelectric material. Pair of n-type and p-type material was obtained without the introduction of external dopant.The pair shows good compatibility factorsuitable for thermoelectric device. In chapter 4, the thermoelectric properties of four selected composition of Bi-Sb-Te synthesized via low temperature milling plus spark plasma sintering is addressed. The analyzed compositions are as follows Bi24Sb20Te56, Bi18Sb11Te71, Bi17Sb6Te77, and Bi28Sb15Te57 respectively. The effect of low temperature milling combine with the prospect of minimum grain growth of spark plasma sintering on the thermoelectric properties of the selected compositions were determined. Samples with eutectic morphology which would otherwise scatter charge carriers were observed to have the highest carrier mobility as a result of high volume fraction of Te phase which serves as a donor injecting excess electrons into the system. The impact of small grain size was observed on the transport properties of the sample Bi28Sb15Te57 with the highest electrical resistivity, the best Seebeck coefficient and the lowest thermal conductivity. Pair of n-type and p-type material was obtained without the introduction of external doping elements. The pairshows good compatibility factor suitable for segmented thermoelectric device. Chapter 5 narrates the thermoelectric properties of four compositions namely Bi30Sb13Te58, Bi23Sb13Te65, Bi18Sb5Te77 and Bi23Sb20Te58subjected to melt spinning plus spark plasma sintering.High cooling rate obtained during melt spinning process was observed in this chapter to cause a shift of composition which resulted in a microstructure morphology with eutectic colonies that is predominantly Te rich. These Te rich colonies in the sample Bi30Sb13Te58 was observed to change the conductivity type of the sample from an otherwise p-type to n-type while also aiding bipolar conduction which was detrimental to the overall thermoelectric performance of the alloy. Segregated Te in the form of eutectic morphology helps to inject excess electron into the bulk of the sample Bi23Sb13Te65 and Bi18Sb5Te77hereby increases the observed electrical conductivity which by virtue of the microstructure morphology is expected to be low. As a result of the processing routes, all four compositions in this chapter shown-type conductivity. Chapter 6 presents the summary of the important conclusions drawn from this work.

In this thesis, a Sb/C composite electrode for sodium-ion batteries isprepared by a simple high energy ball milling and calenderingmethod. The prepared Sb/C composite electrode was assembled in ahalf-cell and symmetrical cell setups in order to perform avariety of electrochemical measurements.The composite electrode showed a reversible specific capacity of595 mAh/g, at a discharge/charge current rate of 15 mA/g. Theelectrode also showed a relatively good performance (compared toprevious studies) of 95% capacity retention after more than 100cycles, at a higher discharge/charge current rate of 60 mA/g. Theelectrode furthermore showed excellent self-dischargecharacteristics, in pause tests implemented over 200 hours (overeight days), which underlined the electrode materials good shelflife properties. A series of Sb/C symmetrical cells assembledthrough-out the project, furthermore, highlighted the stability ofthe solid electrolyte interface (SEI) layer formed on the Sb/Ccomposite electrode during cycling. Scanning electron microscopy(SEM) and Energy-dispersive X-ray spectroscopy (EDS) were used tocharacterize the surface morphology and composition of the Sb/Celectrode, respectively.A non-milled and milled (12 hours) graphite electrodes were alsoprepared for reference and comparison. The milled graphite matrixelectrode provided a reversible capacity of 95 mAhg-1 and acoulombic efficiency (CE) of 99% in over 250 cycles, at a currentrate of 30 mA/g. Milled and non-milled graphite were characterizedwith SEM and Raman spectroscopy, to help have a fundamentalunderstanding of the particle size and material phase,respectively.

Capability of a prototype of miniature collection device based on a strip of the molybdenum foil for collecting hydride forming elements (As, Se, Sb and Bi) was studied. The device was combined with a miniature hydrogen diffusion flame for detection by atomic absorption spectrometry. The conditions for trapping and subsequent vaporization of analytes of interest were optimized. A twin-channel hydride generation system was used for study of mutual interference effects of co-generated hydride forming elements. The influence of modification of the molybdenum surface with noble metals - Rh, Pt and Ir on trapping and vaporization processes was also studied and changes of microstructure of the foil surface after modification were investigated using scanning electron microscope equipped with energy dispersive x-ray analyzer and electron backscattered diffraction system. Complementary radiotracer and radiography experiments were performed in order to determine trapping efficiency and to assess the spatial distribution of collected analytes within the device. Practical application of the method was demonstrated on determination of antimony in water samples at trace level. Possibility of multi-element analysis was demonstrated by combining the collection device with atomization and excitation of the analyte in microwave induced plasma and with detection by atomic emission spectrometry method. The results of the experiments proved that tested miniature collection device is capable of trapping analytes that form volatile hydrides. This device can be coupled to various types of atomizers, typically used in spectrometry methods. Thus, very sensitive and specific detection of hydride forming elements can be performed.

The implementation of energy storage systems in the current electrical grid will increase the grid's reliability and e ciency. Room temperature sodium batteries are seen as potential technology, especially to assist renewable energy generation sources. Currently, suggested negative electrode materials, however, are still not satisfactory for practical use in terms of fabrication costs, gravimetric /volumetric energy densities, cyclability, and irreversible capacity losses occur at the rst cycle. The literature describes various strategies that enhance the specific capacity and/or the cyclability of negative electrode materials but all involve increasing the fabrication costs due to the chosen synthesis or the complexity of the electrode's design. Furthermore, strategies, that reduce the irreversible capacity loss at first cycle, are not discussed. In this present experimental research work, presodiating bulk metallic negative electrode materials prior to cycling, prepared via a simple, cheap and easy-to-scaleup synthesis route, is introduced as a new strategy to improve the cyclability and to effectively reduce the first cycle irreversible capacity loss. Electrochemical and structural experiments were carried out to investigate sodiumtin-antimony powders. Presodiating mechanically bulk Sn-Sb negative electrode materials e ectively reduces the irreversible capacity loss at first cycle and enhances the specific capacity when compared to the non-presodiated powder, while the proper choice of electrode composite and electrolyte formulation improves the cycle life of the electrodes. The enhancement of the electrochemical properties of the presodiated NaSnSb powder, composed of the ternary phase Na5Sb3Sn and an unknown ternary phase crystallising in a hexagonal setting P6, is associated with the stabilisation of the SnSb as desodiation product. Presodiating bulk SnSb negative electrode material is a viable strategy to reduce the first cycle irreversible capacity loss, alleviating the volume changes. With an optimised system, this approach may be extended to other negative electrode materials, reducing the fabrication costs of high capacity negative electrode materials for room temperature sodium batteries. Presodiated NaSnSb negative electrode material may be combined with non-sodiated positive electrode material, such as sulphur to develop competitive room temperature sodium-sulphur batteries. / Die Implementierung von Energiespeichersystemen im bereits bestehenden Stromnetz ist eine der Lösungen, um die Zuverlässigkeit und die Effizienz des Netzes zu nutzen. Raumtemperatur Natrium-Batterien gelten als erfolgsversprechende Technologie insbesondere zur Unterstützung erneuerbarer Energieerzeugungsquellen. Jedoch sind die naheliegenden negativen Elektrodenmaterialien für eine praktische Anwendung hinsichtlich Herstellungskosten, gravimetrischer oder volumetrischer Energiedichte, Zyklenfestigkeit und irreversiblen Kapazitätsverlusten im ersten Zyklus noch nicht zufriedenstellend. Die Literatur beschreibt verschiedene Strategien, die die spezifische Kapazität und / oder die Zyklenfestigkeit von negativen Elektrodenmaterialien verbessern. Diese führen jedoch alle zu einer Erhöhung der Herstellungskosten aufgrund der gewählten Synthese oder des Designs der komplexierten Elektrode. Darüber hinaus werden Strategien zur Reduzierung des irreversiblen Kapazitätsverlusts im ersten Zyklus nicht erörtert. Diese experimentelle Forschungsarbeit präsentiert mit Natrium angereicherte metallische negative Elektrodenmaterialien vor der Wechselbeanspruchung/dem periodischen Durchlaufen, die durch einen schlichten, billigen und einfach zu skalierenden Syntheseweg hergestellt wurden, als eine neue Strategie zur Verbesserung der Zyklenfestigkeit und zur wirksamen Verringerung des irreversiblen Kapazitätsverlusts im ersten Zyklus. Elektrochemische und strukturelle Experimente wurden durchgeführt, um mit Natrium angereichertes Zinn-Antimon-Pulver zu untersuchen. Die mechanischen mit Natrium angereichertes Sn-Sb-negativen Elektrodenmaterialien verringert effektiv den irreversiblen Kapazitätsverlust im ersten Zyklus und erhöht die spezische Kapazität im Vergleich zu dem ohne Natrium angereicherte Pulver, während die richtige Wahl der Elektrodenzusammensetzung und der Elektrolytformulierung die Lebenszyklus der Elektroden verbessert. Die Verbesserung der elektrochemischen Eigenschaften des mit Natrium angereicherten NaSnSb-Pulvers, bestehend aus der ternären Phase Na5Sb3Sn und einer unbekannten ternären Phase, die in einer hexagonalen Aufbau P6 kristallisiert, ist mit der Stabilisierung des Enddesodiationsproduktes beim periodischen Zyklus verbunden, wobei das intermetallische SnSb nach Rekristallisation vorliegt. Mit Natrium angereicherte SnSb negativen Elektrodenmaterialien sind eine tragfähige Strategie zur Verringerung des irreversiblen Kapazitätsverlustes im ersten Zyklus, die Volumenänderungen abschwächen. Mit einem optimierten System kann dieser Ansatz auf andere negative Elektrodenmaterialien erweitert werden um die Herstellungskosten von negativen Elektrodenmaterialien mit hoher Kapazität für Raumtemperatur-Natrium-Batterien zu verringern. Mit Natrium angereichertes NaSnSb-negatives Elektrodenmaterial kann mit nicht mit Natrium versetztem positivem Elektrodenmaterial wie Schwefel kombiniert werden, um realisierbare Raumtemperatur Natrium-Schwefel-Batterien zu entwickeln.