This thesis proposes an analytical method to synthesize bandpass filter with multiple transmission zeros. By using the six pre-determined parameters including two reflection zeros, two matching quality factors, and two transmission zeros, the method can exactly synthesize the corresponding prototype of second-order coupled-resonator bandpass filter. The synthesized filters not only can provide two pre-determined transmission zeros in the lower and upper side of the passband, but also can generate an extra transmission zero in the stopband. This thesis presents the prototypes of the bandpass filter and the methods of synthesis in detail. Finally this thesis implements compact LTCC bandpass filters by using the proposed synthesis method for 3.5 GHz WiMAX applications.

In this thesis two different research topics are undertaken, both in the area of compact RF/microwave circuits design. The first topic involves the design of a compact circularly polarized (CP) slot-ring antenna. A study of several compact CP microstrip and slotline antennas reported in the past has been carried out. In this research, a method of reducing the size of a printed slot-ring antenna is proposed. The reduction in size is achieved by introducing meandered-slot sections in the ring. Circular polarization is achieved by introducing an asymmetry, also a meandered-slot section, and feeding the antenna at an angle of 45o from the asymmetry using a microstrip feed line. The minimum axial ratio of 0.4 dB is obtained at 2.46 GHz, which is the operating frequency of the antenna. The size of the proposed antenna is reduced by about 50% compared to a conventional CP slot-ring antenna and it displays a CP bandwidth of about 2.5%. The simulated and measured results are presented, and they are in good agreement. The small size of the antenna makes it very suitable for use in modern RF/microwave wireless systems which require compact, low cost, and high performance circuits. Moreover, its CP behavior makes it more attractive for applications such as satellite communications. The second topic in the thesis involves the design of a compact microstrip bandpass filter using triangular open-loop resonators. A new compact three-pole microstrip bandpass filter using four triangular open-loop resonators is presented. A fourth resonator is placed to provide cross-coupling in the structure which gives a better skirt rejection. The measured pass-band center frequency is 2.85 GHz. The filter demonstrates about 7% bandwidth with insertion loss of less than 1 dB in the passband, a return loss of greater than 15 dB and out-of-band rejection of greater than 30 dB. The simulated and measured results are in good agreement. The proposed filter is very attractive for use in modern wireless systems which require bandpass filters having compact size, low insertion loss, high selectivity, and good out-of-band rejection.

With the rapidly progress in the microwave communication systems, miniaturization and performance enhancement have become two main requirements of the microwave devices. Microwave dielectric substrates would be the best choice for these requirements, because high dielectric constant of the substrates would reduce the size of the devices, high quality factor of the substrates would improve the microwave characteristics of the devices, and low temperature coefficient of resonant frequency would reduce the shift of the operating frequencies due to the variation of temperature. As mentioned above, the main research of this dissertation is divided into two parts: microwave dielectric materials and microwave filters. 1. Microwave dielectric materials AB2O6 (A=Mg, Zn; B=Ta, Nb) microwave dielectric ceramics have been developed as the microwave dielectric resonators (DRs) in the past, because the dielectric resonators fabricated by AB2O6 ceramics reveal the good microwave dielectric characteristics. However, the temperature coefficients of resonant frequency of MgTa2O6, MgNb2O6, ZnTa2O6, and ZnNb2O6 ceramics are still not good enough for the applications at the microwave frequency. In addition, MgTa2O6 and ZnTa2O6 ceramics reveal positive temperature coefficients of resonant frequency but the MgNb2O6 and ZnNb2O6 ceramics reveal negative temperature coefficients of resonant frequency. In this study, combining of MgNb2O6 ceramics (with negative temperature coefficients of resonant frequency) and MgTa2O6 ceramics (with positive temperature coefficients of resonant frequency) to form Mg(Ta1-xNbx)2O6 ceramics and combining of ZnNb2O6 ceramics (with negative temperature coefficients of resonant frequency) and ZnTa2O6 ceramics (with positive temperature coefficients of resonant frequency) to form Zn(Ta1-xNbx)2O6 ceramics, which all reveal near-zero temperature coefficients of resonant frequencyand are suitable for the applications of microwave communication devices. The sintering and microwave dielectric characteristics of the Mg(Ta1-xNbx)2O6 and Zn(Ta1-xNbx)2O6 dielectric ceramics are also investigated. 2. Wide-band, dual-band, tri-band, and tetra-band bandpass filters Microwave filters have been widely used in the communication systems. The optimal microwave dielectric characteristics of AB2O6 ceramics developed in this thesis were adopted as the substrates of the filters. The performance of the filters was improved obviously due to the high dielectric constant and high quality factor of the microwave dielectric ceramic substrates. At first, a wide-band and a dual-band (2.45/5.2 GHz) bandpass filters are developed by the combination technique of modified end-coupled microstrip lines and half-wavelength ombination technique will generate three transmission zeros easily in the stop-band to improve the characteristics of the filters. And the next, the tri-band (1.57/2.45/5.2 GHz) bandpass filters are developed by the combination of modified end-coupled microstrip lines, outer-frame structures and half-wavelength U-shaped hairpin resonators. The Defected Grounded Structures (DGS) are add into the ground planes of the tri-band bandpass filters to generate the fourth frequency (3.5 GHz), hence, the tetra-band (1.57/2.45/3.5/5.2 GHz) bandpass filters are accomplished. In addition, due to the uses of the high dielectric constant ceramic substrates and the combination techniques, the size of this tetra-band bandpass filter is only 26.3 mm*9.9 mm. Besides, six deeply transmission zeros are generated in the stop-band to improve the characteristics of the filters (1~7 GHz), all the characteristics of this tetra-band filters (frequency, bandwidth, insertion loss, and stop-band rejection) are suitable for the applications of modern communication systems.

Esta dissertação de mestrado apresenta uma metodologia de projeto de filtros de microondas planares passa-faixa tipo patch dual-mode, que associam baixas perdas nos condutores, boa capacidade de potência, rejeição da banda de segunda harmônica e miniaturização. Utilizou-se a ferramenta computacional MATLAB para desenvolver programas de cálculo de dimensões de ressoadores patch single-mode em função da freqüência fundamental e do substrato escolhido, bem como para cálculo da distribuição de campos eletromagnéticos (EM) ao longo destes ressoadores. O simulador EM 3D Momentum/ADS foi utilizado na análise, otimização e simulação do desempenho dos filtros. A metodologia desenvolvida consiste no projeto do ressoador patch single-mode nas geometrias quadrada, triangular e circular, com perturbações tais que resultem na freqüência central e banda de passagem desejadas para o filtro, bem como na miniaturização do mesmo. A metodologia engloba a análise do posicionamento das linhas de entrada e de saída para excitação dos modos desejados e seu acoplamento ao ressoador projetado. Foram propostos três ressoadores patch com topologias originais, modificados pela inserção de fendas, os quais foram aplicados ao projeto, construção e caracterização de cinco filtros. Desses, dois filtros passa-faixa dual-mode de banda mediana utilizam a nova topologia proposta de ressoador patch quadrado. Esses filtros, com dois e com quatro pólos, operam em 2,4 GHz e 2,35 GHz, com banda de passagem fracional de 14% e 9,8%, respectivamente. Outros dois filtros passa-faixa dual-mode de banda estreita, um com dois pólos e outro com quatro pólos, utilizam a topologia original proposta de ressoador patch triangular, com fenda em forma de \"T\" invertido. O filtro com dois pólos opera em 7,8 GHz, com banda de passagem fracional de 4,3% e o filtro de quatro pólos, em 7,5 GHz, com banda de 3,5%. Por fim, o filtro passa-faixa circular banda larga utiliza o ressoador patch circular proposto, que foi modificado para operar como triple-mode, comportamento inédito na literatura internacional enfocando ressoadores patch. Esse filtro triple-mode com três pólos apresenta freqüência central de 2,4 GHz e banda fracional de 29%. Os resultados experimentais validam a aplicação da metodologia, que apresenta grande flexibilidade no projeto de filtros com bandas estreitas, medianas ou largas, com boa rejeição na faixa de segunda harmônica (resultados acima de 13 dB). Conseguem-se leiautes miniaturizados com redução em área maior que 50% e ao mesmo tempo sem dimensões críticas, o que resulta em facilidade de fabricação através de métodos tradicionais de fotogravação em placas de circuito impresso. / This dissertation presents a methodology for the design of microwave planar bandpass filters using dual-mode patch resonators, which have low conductor loss, high power handling, second harmonic band rejection and miniaturization. MatLab software was used to develop routines that can calculate the dimensions of the single-mode patch resonators as a function of their fundamental frequency and of the chosen substrate. Further, these routines are able to calculate the electromagnetic (EM) field patterns across these resonators. Momentum/ADS EM 3D software was used for the analysis, optimization and simulation of the performance of the filters. The developed methodology consists on the design of the single-mode patch resonator in either square, rounded or triangular shape with perturbations that result in the desired filter\'s central frequency and bandwidth, and also in its miniaturization. The methodology involves the positioning of the input and output transmission lines to excite the desired modes and their coupling to the developed resonator. Three patch resonators were proposed with novel topologies that were modified by the insertion of slots, and applied to the design, fabrication, and measurements of five filters. Out of these five filters, two are dualmode medium band filters that use the proposed new topology for the square patch resonator. These filters, with two and four poles, are centered at 2.4 GHz and 2.35 GHz, with fractional bandwidth of 14% and 9.8%, respectively. Other two filters are dual-mode narrowband filters, a two-pole and a four-pole, that use the original topology proposed for the triangular patch resonator with a \"T\"-shaped slot. The two-pole filter is centered at 7.8 GHz with fractional bandwidth of 4.3%, whereas the four-pole filter is centered at 7.5 GHz with 3.5% of bandwidth. The last filter is a broadband circular filter that uses the proposed circular triplemode patch resonator, which is a brand new behavior in the international literature that focus on patch resonators. This triple-mode filter with three poles is centered at 2.4 GHz with fractional bandwidth of 29%. Experimental results validate the methodology, which presents wide filter design flexibility with narrow, medium or broad bands, and good second harmonic rejection (results better than 13 dB). Layouts can be designed with more than 50% of area reduction, and without critical dimensions at the same time, resulting in a simple fabrication that utilizes conventional PCB photopatterning process.

Esta dissertação de mestrado apresenta uma metodologia de projeto de filtros de microondas planares passa-faixa tipo patch dual-mode, que associam baixas perdas nos condutores, boa capacidade de potência, rejeição da banda de segunda harmônica e miniaturização. Utilizou-se a ferramenta computacional MATLAB para desenvolver programas de cálculo de dimensões de ressoadores patch single-mode em função da freqüência fundamental e do substrato escolhido, bem como para cálculo da distribuição de campos eletromagnéticos (EM) ao longo destes ressoadores. O simulador EM 3D Momentum/ADS foi utilizado na análise, otimização e simulação do desempenho dos filtros. A metodologia desenvolvida consiste no projeto do ressoador patch single-mode nas geometrias quadrada, triangular e circular, com perturbações tais que resultem na freqüência central e banda de passagem desejadas para o filtro, bem como na miniaturização do mesmo. A metodologia engloba a análise do posicionamento das linhas de entrada e de saída para excitação dos modos desejados e seu acoplamento ao ressoador projetado. Foram propostos três ressoadores patch com topologias originais, modificados pela inserção de fendas, os quais foram aplicados ao projeto, construção e caracterização de cinco filtros. Desses, dois filtros passa-faixa dual-mode de banda mediana utilizam a nova topologia proposta de ressoador patch quadrado. Esses filtros, com dois e com quatro pólos, operam em 2,4 GHz e 2,35 GHz, com banda de passagem fracional de 14% e 9,8%, respectivamente. Outros dois filtros passa-faixa dual-mode de banda estreita, um com dois pólos e outro com quatro pólos, utilizam a topologia original proposta de ressoador patch triangular, com fenda em forma de \"T\" invertido. O filtro com dois pólos opera em 7,8 GHz, com banda de passagem fracional de 4,3% e o filtro de quatro pólos, em 7,5 GHz, com banda de 3,5%. Por fim, o filtro passa-faixa circular banda larga utiliza o ressoador patch circular proposto, que foi modificado para operar como triple-mode, comportamento inédito na literatura internacional enfocando ressoadores patch. Esse filtro triple-mode com três pólos apresenta freqüência central de 2,4 GHz e banda fracional de 29%. Os resultados experimentais validam a aplicação da metodologia, que apresenta grande flexibilidade no projeto de filtros com bandas estreitas, medianas ou largas, com boa rejeição na faixa de segunda harmônica (resultados acima de 13 dB). Conseguem-se leiautes miniaturizados com redução em área maior que 50% e ao mesmo tempo sem dimensões críticas, o que resulta em facilidade de fabricação através de métodos tradicionais de fotogravação em placas de circuito impresso. / This dissertation presents a methodology for the design of microwave planar bandpass filters using dual-mode patch resonators, which have low conductor loss, high power handling, second harmonic band rejection and miniaturization. MatLab software was used to develop routines that can calculate the dimensions of the single-mode patch resonators as a function of their fundamental frequency and of the chosen substrate. Further, these routines are able to calculate the electromagnetic (EM) field patterns across these resonators. Momentum/ADS EM 3D software was used for the analysis, optimization and simulation of the performance of the filters. The developed methodology consists on the design of the single-mode patch resonator in either square, rounded or triangular shape with perturbations that result in the desired filter\'s central frequency and bandwidth, and also in its miniaturization. The methodology involves the positioning of the input and output transmission lines to excite the desired modes and their coupling to the developed resonator. Three patch resonators were proposed with novel topologies that were modified by the insertion of slots, and applied to the design, fabrication, and measurements of five filters. Out of these five filters, two are dualmode medium band filters that use the proposed new topology for the square patch resonator. These filters, with two and four poles, are centered at 2.4 GHz and 2.35 GHz, with fractional bandwidth of 14% and 9.8%, respectively. Other two filters are dual-mode narrowband filters, a two-pole and a four-pole, that use the original topology proposed for the triangular patch resonator with a \"T\"-shaped slot. The two-pole filter is centered at 7.8 GHz with fractional bandwidth of 4.3%, whereas the four-pole filter is centered at 7.5 GHz with 3.5% of bandwidth. The last filter is a broadband circular filter that uses the proposed circular triplemode patch resonator, which is a brand new behavior in the international literature that focus on patch resonators. This triple-mode filter with three poles is centered at 2.4 GHz with fractional bandwidth of 29%. Experimental results validate the methodology, which presents wide filter design flexibility with narrow, medium or broad bands, and good second harmonic rejection (results better than 13 dB). Layouts can be designed with more than 50% of area reduction, and without critical dimensions at the same time, resulting in a simple fabrication that utilizes conventional PCB photopatterning process.

In modern wireless communication and radar systems, filters play an important role in getting a high-quality signal while rejecting spurious and neighboring unwanted signals. The filters with reconfigurable features, such as tunable bandwidths or switchable dual bands, also play a key part both in realizing the compact size of the system and in supporting multi-communication services. The Chapters II-IV of this dissertation show the studies of the filters for microwave communication. Bandpass filters realized in ring resonators with stepped impedance stubs are introduced. The effective locations of resonant frequencies and transmission zeros are analyzed, and harmonic suppression by interdigital-coupled feed lines is discussed. To vary mid-upper and mid-lower passband bandwidths separately, the characteristic impedances of the open-circuited stubs are changed. Simultaneous change of each width of the open-circuited stub results in variable passband bandwidths. Asymmetric stepped-impedance resonators are also used to develop independently controllable dual-band (2.4 and 5.2 GHz) bandpass filters. By extending feed lines, a transmission zero is created, which results in the suppression of the second resonance of 2.4-GHz resonators. To determine the precise transmission zeros, an external quality factor at feeders is fixed while extracting coupling coefficients between the resonators. Two kinds of feed lines, such as hook-type and spiral-type, are developed, and PIN diodes are controlled to achieve four states of switchable dual-band filters. Beam-scanning features of the antennas are very important in the radar systems. Phase shifters using piezoelectric transducers and dielectric leaky-wave antennas using metal strips are studied in the Chapters V-VII of this dissertation. Meandered microstrip lines are used to reduce the size of the phase shifters working up to 10 GHz, and reflection-type phase shifters using piezoelectric transducers are developed. A dielectric film with metal strips fed by an image line with a high dielectric constant is developed to obtain wide and symmetrical beam-steering angle. In short, many techniques are presented for realizing reconfigurable filters and large beam-scan features in this dissertation. The result of this work should have many applications in various wireless communication and radar systems.

In wireless transceiver circuits some of the most prevalent required off-chip components are discrete filters. These components are generally implemented with surface acoustic wave (SAW) or ceramic components. These devices are used in the receiver section for discrimination of incoming radio frequency (RF) signals as well as downconverted intermediate frequency (IF) signals. Presently, with the growing demand for multi-functional wireless consumer devices, the need for full integration of RF and logic circuits in wireless communications systems is becoming increasingly evident. If integrated RF filters with acceptable electrical characteristics could be realized, this might reduce or eliminate the currently required off-chip filters, prospectively decreasing the complexity, size, and cost of future wireless transceiver circuits and systems. The objective of the present research effort is to implement an integrated Q-enhanced LC bandpass filter in a prospective receiver front-end RF amplifier using the passive and active components available in a standard digital complementary metal-oxide semiconductor (CMOS) process. CMOS is the standard design medium for digital circuitry, and with the increased unity gain or transit frequency (fT) values that accompany steadily shrinking CMOS device sizes, the implementation of gigahertz frequency communications circuits in this medium is increasingly feasible. The circuit design specifically investigated in this work introduces a loss-compensated second-order gigahertz range bandpass filter implemented in a 0.18 쭠digital CMOS process provided by National Semiconductor. This filter incorporates a unique design technique that provides improvements in filter linearity through an independently variable bias level shifting method, while also facilitating prospective single-to-differential signal conversion. One distinctive characteristic of the investigated circuit, in comparison to other RF integrated filter work, is the implementation of a novel integrated transformer feedback method that facilitates magnetically coupled loss-restoration and subsequent filter Q-enhancement. Additionally, this loss restoration method is achieved using a single transistor, in contrast to the multi-transistor cross-coupled transconductor Q-enhancement technique commonly implemented in other previous and current integrated RF filter research.

This research focuses on biologically inspired audio signal processing using programmable analog circuitry. This research is inspired by the biology of the human cochlea since biology far outperforms any engineered system at converting audio signals into meaningful electrical signals. The human cochlea efficiently decomposes any sound into the respective frequency components by harnessing the resonance nature of the basilar membrane, essentially forming a bank of bandpass filters. In a similar fashion, this work revolves around developing a filter bank composed of continuous-time, low-power, analog bandpass filters that serve as the core front end to this silicon audio-processing system. Like biology, the individual bandpass filters are tuned to have narrow bandwidths, moderate amounts of resonance, and exponentially spaced center frequencies. This audio front end serves to efficiently convert incoming sounds into information useful to subsequent signal-processing elements, and it does so by performing a frequency decomposition of the waveform with extremely low-power consumption and real-time operation. To overcome mismatch and offsets inherent in CMOS processes, floating-gate transistors are used to precisely tune the time constants in the filters and to allow programmability of analog components.

This dissertation aims to design and implement wireless passive components using domestic integrated passive device (IPD) technology. The research focuses on exploiting novel 3-D structures for various kinds of IPD-based wireless passive components including high-quality and high-efficiency planar transformers, baluns, filters, and combiners to achieve miniature size and high performance. A physical model has been developed for modeling the planar transformers. In this dissertation, a scalable transformer model in integrated passive device technology is further used to correlate with the coupled-line sections of a conventional Marchand balun. This improves the efficiency of the design of planar transformers with equivalent coupled-line parameters such as the coupling factor, and even- and odd-mode characteristic impedances and quality factors. Additionally, the proposed model-based design approach provides effective optimization techniques that incorporate geometrical and material parameters. In addition, a compact transformer-based coupled balun bandpass filter design is proposed based on integrated circuit technology and the equivalent circuit is established. Using a planar transformer with high-density fully symmetrical wiring not only greatly reduces the component size but also provides a superior stopband rejection and selectivity. Finally, by using the spiral-shaped resonators, the dual-band third-order bandpass filter has been implemented on organic substrates. The proposed BPF design is verified to overcome the elements¡¦ parasitic effects, and thus can be miniaturized and optimized with high degree of freedom. The simulation and measurement results have good agreement for the proposed design in this dissertation.

Due to the demand for high‐performance radio frequency (RF) integrated circuit design in the past years, a system‐on‐chip (SoC) that enables integration of analog and digital parts on the same die has become the trend of the microelectronics industry. As a result, a major requirement of the next generation of wireless devices is to support multiple standards in the same chip‐set. This would enable a single device to support multiple peripheral applications and services. Based on the aforementioned, the traditional superheterodyne front‐end architecture is not suitable for such applications as it would require a complete receiver for each standard to be supported. A more attractive alternative is the highintermediate frequency (IF) radio architecture. In this case the signal is digitalized at an intermediate frequency such as 200MHz. As a consequence, the baseband operations, such as down‐conversion and channel filtering, become more power and area efficient in the digital domain. Such architecture releases the specifications for most of the front‐end building blocks, but the linearity and dynamic range of the ADC become the bottlenecks in this system. The requirements of large bandwidth, high frequency and enough resolution make such ADC very difficult to realize. Many ADC architectures were analyzed and Continuous‐Time Bandpass Sigma‐Delta (CT‐BP‐ΣΔ) architecture was found to be the most suitable solution in the high‐IF receiver architecture since they combine oversampling and noise shaping to get fairly high resolution in a limited bandwidth. A major issue in continuous‐time networks is the lack of accuracy due to powervoltage‐ temperature (PVT) tolerances that lead to over 20% pole variations compared to their discrete‐time counterparts. An optimally tuned BP ΣΔ ADC requires correcting for center frequency deviations, excess loop delay, and DAC coefficients. Due to these undesirable effects, a calibration algorithm is necessary to compensate for these variations in order to achieve high SNR requirements as technology shrinks. In this work, a novel linearization technique for a Wideband Low‐Noise Amplifier (LNA) targeted for a frequency range of 3‐7GHz is presented. Post‐layout simulations show NF of 6.3dB, peak S21 of 6.1dB, and peak IIP3 of 21.3dBm, respectively. The power consumption of the LNA is 5.8mA from 2V. Secondly, the design of a CMOS 6th order CT BP‐ΣΔ modulator running at 800 MHz for High‐IF conversion of 10MHz bandwidth signals at 200 MHz is presented. A novel transconductance amplifier has been developed to achieve high linearity and high dynamic range at high frequencies. A 2‐bit quantizer with offset cancellation is alsopresented. The sixth‐order modulator is implemented using 0.18 um TSMC standard analog CMOS technology. Post‐layout simulations in cadence demonstrate that the modulator achieves a SNDR of 78 dB (~13 bit) performance over a 14MHz bandwidth. The modulator’s static power consumption is 107mW from a supply power of ± 0.9V. Finally, a calibration technique for the optimization of the Noise Transfer Function CT BP ΣΔ modulators is presented. The proposed technique employs two test tones applied at the input of the quantizer to evaluate the noise transfer function of the ADC, using the capabilities of the Digital Signal Processing (DSP) platform usually available in mixed‐mode systems. Once the ADC output bit stream is captured, necessary information to generate the control signals to tune the ADC parameters for best Signal‐to‐Quantization Noise Ratio (SQNR) performance is extracted via Least‐ Mean Squared (LMS) software‐based algorithm. Since the two tones are located outside the band of interest, the proposed global calibration approach can be used online with no significant effect on the in‐band content.